General Specifications

Transcription

1 General Specifications GS 0121F01-02E odel EJ530/H Gauge Pressure Transmitter (High ccuracy Type) [Style: S2] The gauge pressure transmitter model EJ530/H can be used to measure liquid, gas, or steam pressure. oth output a 4 to 20 m signal corresponding to the measured pressure, and also feature remote setup and monitoring through communications with the RIN terminal and ENTU S or µxl or HRT 275 host. STNR SPEIFITIONS Refer to GS 0122T02-00E for FOUNTION Fieldbus communication type and GS 0122T03-00E for PROFIUS P communication type marked with. PERFORNE SPEIFITIONS Zero-based calibrated span, linear output, wetted parts material code S and silicone oil. Reference ccuracy of alibrated Span (including the effects of zero-based linearity, hysteresis, and repeatability) % of Span, (, and capsule) 0.12 % of Span, ( capsule) For spans below X, [ X ] % of span, (, and capsule) Span X [ ] % of span, ( capsule) Span Where X equals: apsule X Pa {psi} 40 kpa {5.8} 0.2 {29} 1 {145} 8 {1160} mbient Temperature Effects Total Effects per 28 (50 F) hange [0.15% Span 0.15% URL] Stability 0.1% of URL per 12 months Vibration Effects 0.1 % of URL (5 to 15Hz; 4mm peak-to-peak constant displacement, 15 to 150Hz; 2g, 150 to 2000Hz; 1g) Power Supply Effects % per Volt (from 21.6 to 32 V, 350 ) FUNTIONL SPEIFITIONS Span & Limits easurement Span and Pa psi (/1) bar (/3) kgf/cm 2 (/4) Span Span 10 to 200 kpa 0.1 to to to to to to 2 1 to 20 5 to to 2 1 to 20 5 to to 200 kpa 0 to 2 0 to 10 0 to 29 0 to to to 2 0 to 20 0 to to 2 0 to 20 0 to 100 Span 5 to to to to to 50 0 to to to 500 T01E.EPS URL is defined as the Upper Limit from the table above. Zero djustment Limits Zero can be fully elevated or suppressed, within the Lower and Upper Limits of the capsule. External Zero djustment External zero is continuously adjustable with 0.01 % incremental resolution of span. Span may be adjusted locally using the digital indicator with range switch. ounting Position Effect Rotation in diaphragm plane has no effect. Tilting up to 90 will cause zero shift up to 0.27 kpa {1.1 inh 2 O} which can be corrected by the zero adjustment. Output Two wire 4 to 20 m output with digital communications. RIN or HRT FSK protocol are superimposed on the 4 to 20 m signal. Failure larm Output status at PU failure and hardware error; Up-scale: 110%, 21.6 m or more (standard) own-scale: -5%, 3.2 m or less -2.5%, 3.6 m or less (Optional code /F1) Note : pplicable for Output signal code and E. Yokogawa Electric orporation , Nakacho, usashino-shi, Tokyo, Japan Phone: Fax.: GS 0121F01-02E opyright pr th Edition pril 2013

2 amping Time onstant (1st order) The sum of the amplifier and capsule damping time constant must be used for the overall time constant. mp damping time constant is adjustable from 0.2 to 64 seconds. apsule (Silicone Oil),,, and Time onstant (approx. sec) 0.2 mbient Temperature Limits (approval codes may affect limits) -40 to 85 (-40 to 185 F) -30 to 80 (-22 to 176 F) with L isplay Process Temperature Limits (approval codes may affect limits) -40 to 120 (-40 to 248 F) mbient Humidity Limits 5 to 100 % 40 (104 F) aximum Overpressure apsule Pressure 4 Pa {580 psig} 4 Pa {580 psig} 20 Pa {2900 psig} 60 Pa {8500 psig} Working Pressure Limits (Silicone Oil) aximum Pressure Limit apsule Pressure 200 kpa {29 psig} 2 Pa {290 psig} 10 Pa {1450 psig} 50 Pa {7200 psig} Supply & Load Requirements (Safety approvals can affect electrical requirements, see graph below) With 24 V supply, up to a 570 load can be used. 600 External load resistance 250 R= E igital ommunication range Supply Voltage 10.5 to 42 V for general use and flameproof type 10.5 to 32 V for lightning protector (Optional code /) 10.5 to 30 V for intrinsically safe, Type n, nonincendive, or non-sparking type inimum voltage limited at 16.4 V for digital communications, RIN and HRT Load (Output signal code and E) 0 to 1335 for operation 250 to 600 for digital communication E onformity Standards :, EN lass, Table2 (For use in industrial locations) EN European Pressure Equipment irective 97/23/E Sound Engineering Practice With option code /PE3 ategory III, odule H, Type of Equipment: Pressure ccessory-vessel, Type of Fluid: Liquid and Gas, Group of Fluid: 1 and 2 Safety Requirement Standards EN ltitude of installation site: ax. 2,000 m above sea level Installation category: I Pollution degree: 2 Indoor/Outdoor use ommunication Requirements RIN ommunication istance Up to 2 km (1.25 miles) when using EV polyethylene-insulated PV-sheathed cables. ommunication distance varies depending on type of cable used. Load apacitance 0.22 F or less (see note) Load Inductance 3.3 mh or less (see note) Spacing from power line 15 cm or more. Input Impedance of communicating device 10 k or more at 2.4 khz. Note : For general-use and Flameproof type. For Intrinsically safe type, please refer to OPTIONL SPEIFITIONS. 2 R ( ) Power supply voltage E (V ) F01E.EPS Figure 1. Relationship etween Power Supply Voltage and External Load Resistance GS 0121F01-02E pril 01,

3 PHYSIL SPEIFITIONS Wetted Parts aterials: iaphragm and Process connector Refer to OEL N SUFFIX OE. Non-wetted Parts aterials: Housing Low copper cast-aluminum alloy with polyurethane paint (unsell 0.6GY3.1/2.0) egrees of Protection IP67, NE4X over O-rings una-n, fluoro-rubber (optional) ata plate and tag SUS304 or SUS316 (option) Fill Fluid Silicone, Fluorinated oil (option) Weight 1.6 kg (3.5 lb) without integral indicator, mounting bracket. onnections Refer to the model code to specify the process and the electrical connection type. < Settings When Shipped > Tag Number Output ode isplay ode Operation ode amping Time onstant alibration Lower Value alibration Higher Value alibration Units s specified in order *1 Linear Linear Normal unless otherwise specified in order 2 sec. s specified in order s specified in order Selected from mmh 2 O, mmq, mmwg, mmhg, Torr, Pa, hpa, kpa, Pa, mbar, bar, gf/cm 2, kgf/cm 2, inh 2 O, inhg, fth 2 O, psi, or atm.(only one unit can be specified) *1: Up to 16 alphanumeric characters for RIN and 8 characters for HRT including - and. will be entered in the amplifier memory. If specified Tag includes other characters than above, it will not be entered in the amplifier memory. T05E.EPS < Related Instruments > Power istributor: Refer to GS 0104T01-02E or GS 0104T02-02E RIN TERINL: Refer to GS E < Reference > 1. Teflon; Trademark of E.I. upont de Nemours & o. 2. Hastelloy; Trademark of Haynes International Inc. 3. HRT; Trademark of the HRT ommunication Foundation. 4. FOUNTION ; Trademark of Fieldbus Foundation. 5. PROFIUS; Registered trademark of Profibus Nutzerorganisation e.v., Karlsruhe, Germany. aterial ross Reference Table SUS316L ISI 316L SUS316 SUS304 ISI 316 ISI 304 S25 ISI 1025 S435 ISI 4137 SUS630 ST630 SS14 ST F-8 T07E.EPS 6. Other company names and product names used in this material are registered trademarks or trademarks of their respective owners. < Specification onformance > The model EJ530 maintain a specification conformance to at least 3. 3 GS 0121F01-02E July 01,

4 4 OEL N SUFFIX OES odel EJ530 odel EJ530 Output Signal easurement span (capsule) Wetted parts material *2 Process connection Electrical connection Integral indicator ounting bracket High accuracy Optional codes Suffix odes E F G S # H # N E N E F L N /H... escription Gauge pressure transmitter 4 to 20 m with digital communication (RIN protocol) 4 to 20 m with digital communication (HRT protocol, refer to GS 0122T01-00E) igital communication (FOUNTION Fieldbus protocol, refer to GS 0122T02-00E) igital communication (PROFIUS P protocol, refer to GS 0122T03-00E) 10 to 200 kpa {0.1 to 2 kgf/cm 2 } {1.45 to 29 psi} {0.1 to 2 bar} 0.1 to 2 Pa {1 to 20 kgf/cm 2 } {14.5 to 290 psi} {1 to 20 bar} 0.5 to 10 Pa {5 to 100 kgf/cm 2 } {72.5 to 1450 psi} {5 to 100 bar} 5 to 50 Pa {50 to 500 kgf/cm 2 } {720 to 7200 psi} {50 to 500 bar} [Process onnection] [iaphragm] SUS316L * 4 Hastelloy -276 * 3 Hastelloy -276 *3 Hastelloy -276 * 3 1/2 NPT female 1/2 NPT male G 1/2 IN male IN male lways N lways 0 G1/2 female, one electrical connection 1/2 NPT female, two electrical connections without blind plug Pg 13.5 female, two electrical connections without blind plug 20 female, two electrical connections without blind plug G1/2 female, two electrical connections and a blind plug 1/2 NPT female, two electrical connections and a blind plug Pg 13.5 female, two electrical connections and a blind plug 20 female, two electrical connections and a blind plug G1/2 female, two electrical connections and a SUS316 blind plug 1/2 NPT female, two electrical connections and a SUS316 blind plug 20 female, two electrical connections and a SUS316 blind plug igital indicator igital indicator with the range setting switch * 1 (None) SE arbon steel 2-inch pipe mounting SUS316 2-inch pipe mounting SUS316 2-inch pipe mounting (None) lways /H / Optional specification The marks indicate the most typical selection for each specification. Example: EJ530-S4N-02NN/H/ The # marks indicate the construction materials conform to NE material recommendations per R For the use of SUS316 material, there may be certain limitations for pressure and temperature. Please refer to NE standards for details. *1: Not applicable for Output signal code F and G. *2: Users must consider the characteristics of selected wetted parts material and the influence of process fluids. The use of inappropriate materials can result in the leakage of corrosive process fluids and cause injury to personnel and/or damage to plant facilities. It is also possible that the diaphragm itself can be damaged and that material from the broken diaphragm and the fill fluid can contaminate the user's process fluids. e very careful with highly corrosive process fluids such as hydrochloric acid, sulfuric acid, hydrogen sulfide, sodium hypochlorite, and high-temperature steam (150 [302 F] or above). ontact Yokogawa for detailed information of the wetted parts material. *3: Hastelloy -276 or ST N *4: SUS316L or ST grade 316L. T02E.EPS GS 0121F01-02E Jul. 08,

5 5 OPTIONL SPEIFITIONS (For Explosion Protected types ) For FOUNTION Fieldbus explosion protected type, see GS 0122T02-00E. For PROFIUS P explosion protected type, see GS 0122T03-00E. Item escription ode F Explosionproof pproval * 1 * 3 * 4 pplicable standard: F3600, F3615, F3810, NSI/NE250 Explosionproof for lass I, ivision 1, Groups, and ust-ignitionproof for lass II/III, ivision 1, Groups E, F and G FF1 Hazardous (classified) locations, indoors and outdoors (NE 4X) Temperature class: T6 mb. Temp.: 40 to 60 ( 40 to 140 F) F Intrinsically safe pproval * 1 * 3 * 4 pplicable standard: F3600, F3610, F3611, F3810, NSI/NE250 Factory utual (F) Intrinsically Safe for lass I, ivision 1, Groups,, &, lass II, ivision 1, Groups E, F & G and lass III, ivision 1 Hazardous Locations. Nonincendive for lass I, ivision 2, Groups,, &, lass II, ivision. 2, Groups E, F & G, and lass III, ivision 1 Hazardous Locations. FS1 Enclosure: NE 4X, Temp. lass: T4, mb. Temp.: 40 to 60 ( 40 to 140 F) Intrinsically Safe pparatus Parameters [Groups,,,, E, F and G] Vmax=30 V, Imax=165 m, Pmax=0.9 W, i=22.5 nf, Li=730 H [Groups,, E, F and G] Vmax=30 V, Imax=225 m, Pmax=0.9 W, i=22.5 nf, Li=730 H ombined FF1 and FS1 * 1 * 3 * 4 FU1 TEX Flameproof pproval * 2 * 4 pplicable standard: EN , EN ertificate: KE 02TEX2148 II 2G Ex d II T4, T5, T6 KF21 mb. Temp.: T5; 40 to 80 ( 40 to 176 F), T4 and T6; 40 to 75 ( 40 to 167 F) ax. process Temp.: T4; 120 (248 F), T5; 100 (212 F), T6; 85 (185 F) TEX TEX Intrinsically safe pproval * 2 * 3 * 4 pplicable standard: EN50014, EN50020, EN50284 ertificate: KE 02TEX1030X KS2 II 1G EEx ia II T4, mb. Temp.: 40 to 60 ( 40 to 140 F) Ui=30 V, Ii=165 m, Pi=0.9 W, i=22.5 nf, Li=730 H *1: pplicable for Electrical connection code 2, 7 and (1/2 NPT female). *2: pplicable for Electrical connection code 2, 4, 7, 9, and (1/2 NPT and 20 female). *3: pplicable for Output signal code and E. For intrinsically safe approval, use the safety barrier certified by the testing laboratories (R-400 is not applicable). *4: Lower limit of ambient temperature is 15 (5 F) when /HE is specified. T03-1E.EPS GS 0121F01-02E pril 01,

6 6 Item escription ode S Explosionproof pproval * 1 * 3 * 4 pplicable standard: 22.2 No. 0, No. 0.4, No. 25, No. 30, No. 94, No. 142 ertificate: Explosionproof for lass I, ivision 1, Groups, and ustignitionproof for lass II/III, ivision 1, Groups E, F and G ivision2 SELS NOT REQUIRE, Temp. lass: T4, T5, T6 Encl Type 4x ax. Process Temp.: T4; 120 (248 F), T5; 100 (212 F), T6; 85 (185 F) mb. Temp.: 40 to 80 ( 40 to 176 F) Process Sealing ertification ual Seal ertified by S to the requirement of NSI/IS No additional sealing required. Primary seal failure annunciation: at the zero adjustment screw anadian Standards ssociation (S) S Intrinsically safe pproval * 1 * 3 * 4 pplicable standard: 22.2 No. 0, No. 0.4, No. 25, No. 30, No. 94, No. 142, No. 157, No. 213 ertificate: lass I, Groups,, and lass II and III, Groups E, F and G Encl Type 4x, Temp. lass: T4, mb. Temp.: 40 to 60 ( 40 to 140 F) Vmax=30 V, Imax=165 m, Pmax=0.9 W, i=22.5 nf, Li=730 H Process Sealing ertification ual Seal ertified by S to the requirement of NSI/IS No additional sealing required. Primary seal failure annunciation: at the zero adjustment screw IEEx Scheme ombined F1 and S1 * 1 * 3 * 4 IEEx Intrinsically safe, type n and Flameproof pproval * 3 * 4 * 5 Intrinsically safe and type n pplicable Standard: IE :2004, IE :1999, IE :2005, IE :2005 ertificate: IEEx KE X Ex ia II T4, Ex nl II T4 Enclosure: IP67 mb. Temp.: 40 to 60 ( 40 to 140 F), ax. Process Temp.: 120 (248 F) Electrical Parameters: [Ex ia] Ui=30 V, Ii=165 m, Pi=0.9 W, i=22.5 nf, Li=730 H [Ex nl] Ui=30 V, i=22.5 nf, Li=730 H Flameproof pplicable Standard: IE :2004, IE :2003 ertificate: IEEx KE Ex d II T6...T4 Enclosure: IP67 ax.process Temp.: T4;120 (248 F), T5;100 (212 F), T6; 85 (185 F) mb.temp.: 40 to 75 ( 40 to 167 F) for T4, 40 to 80 ( 40 to 176 F) for T5, 40 to 75 ( 40 to 167 F) for T6 *1: pplicable for Electrical connection code 2, 7 and (1/2 NPT female). *2: pplicable for Electrical connection code 2, 4, 7, 9, and (1/2 NPT and 20 female). *3: pplicable for Output signal code and E. For intrinsically safe approval, use the safety barrier certified by the testing laboratories (R-400 is not applicable). *4: Lower limit of ambient temperature is 15 (5 F) when /HE is specified. *5: pplicable for Electrical connection code 2, 4, 7, and (1/2 NPT and 20 female). F1 S1 U1 SU2 T03-2E.EPS GS 0121F01-02E July 01,

7 7 OPTIONL SPEIFITIONS Item escription ode mplifier cover only P Painting * 11 olor change oating change mplifier cover and terminal cover, unsell 7.5 R4/14 Epoxy resin-baked coating * 14 PR X1 316 SST exterior parts Exterior parts on the amplifier housing (name plates, tag plate, zero-adjustment screw, stopper screw) will become 316 SST * 16 H Fluoro-rubber O-ring ll O-rings of amplifier housing. Lower limit of ambient temperature: 15 (5 F) HE Lightning protector Oil-prohibited use alibration units * 1 Fast response * 9 Failure alarm down-scale * 2 NUR NE43 compliant * 2 * 10 ata configuration at factory * 15 Stainless steel amplifier housing * 3 ill ertificate Pressure test/leak test ertificate * 12 Transmitter power supply voltage: 10.5 to 32 V (10.5 to 30 V for intrinsically safe type, 9 to 32 V for Fieldbus communication type.) llowable current: ax (1 40 ms), Repeating 1000 (1 40 ms) 100 times egrease cleansing treatment egrease cleansing treatment with fluorinated oil filled capsule. Operating temperature 20 to 80 P calibration (psi unit) bar calibration (bar unit) calibration (kgf/cm 2 unit ) (See Table for Span and Limits.) Update time: sec mplifier damping time constant: 0.1 to 64 sec in 9 increments Response time (with min. damping time constant): max. 0.3 sec Output status at PU failure and hardware error is 5%, 3.2 m or less. Output signal limits: 3.8 m to 20.5 m escription into escriptor parameter of HRT protocol mplifier housing material; SS14 stainless steel (equivalent to SUS316 cast stainless steel or ST F-8) Process connector Test Pressure: 200 kpa (2 kgf/cm 2 ) * 4 Test Pressure: 2 Pa (20 kgf/cm 2 ) * 5 Test Pressure: 10 Pa (100 kgf/cm 2 ) * 6 Test Pressure: 50 Pa (500 kgf/cm 2 ) * 7 Failure alarm down-scale: output status at PU failure and hardware error is 5%, 3.2 m or less. Failure alarm up-scale: output status at PU failure and hardware error is 110%, 21.6 m or more. Wired tag plate Stainless steel tag plate wired onto transmitter N4 European Pressure Equipment irective * 13 PE 97/23/E ategory: III, odule: H, Type of Equipment: Pressure ccessory-vessel, Type of Fluid: Liquid and Gas, Group of Fluid: 1 and 2 Nitrogen (N 2 ) Gas or Water * 8 Retention time: 10 minutes *1: The unit of WP (ax. working pressure) on the name plate of a housing is the same unit as specified by Option code 1, 3 and 4. *2: pplicable for Output signal code and E. The hardware error indicates faulty amplifier or capsule. When combining with Option code F1, output status for down-scale is 2.5%, 3.6 m or less. *3: pplicable for Electrical connection code 2, 3, 4,, and. Not applicable for Option code P and X1. *4: pplicable for apsule code. *5: pplicable for apsule code. *6: pplicable for apsule code. *7: pplicable for apsule code. Write protection switch is attached for Output code E. *8: Pure nitrogen gas or pure water is used for oil-prohibited use (Option code K1 and K2) *9: pplicable for Output signal code and E. Write protection switch is attached for Output code E. *10: Not applicable for Option code 1. *11: Standard polyurethan painting can be used in acid atmosphere, whereas the epoxy resin-baked coating (Option code X1) can be used in alkaline atmosphere. nti-corrosion coating, the combination of polyurethan and epoxy resin-baked coating, is available by special order as sea water, alkaline, and acid resistant. *12: The unit on the certificate is always kpa or Pa regardless of selection of option code 1, 3, or 4. *13: If compliance with category III is needed, specify this option code. *14: Not applicable for color change option. *15: pplicable for Output signal code E. *16: 316 or 316L SST. The specification is included in option code /E1. K1 K F E1 PE3 15 T05 T06 T07 T08 T04E.EPS GS 0121F01-02E July 01,

8 8 IENSIONS odel EJ530 With Process onnection code 7 Unit: mm(pprox. inch) 96(3.77) 41(1.61) onduit connection 12 (0.47) 110(4.33) 45 (1.77) Ground terminal Shrouding bolt * 2 127(5.0) 170(6.69) 78 (3.07) Zero adjustment LOK ZERO LOK 111(4.37) 124(4.88) dapter Pipe(Open to atmosphere) *1 47 (1.85) 44(1.73) 91(3.58) 2-inch pipe (O mm) ounting bracket *1: pplied to odel EJ530 with easurement span code,, and. *2: pplicable only for TEX and IEEx Flameproof type. For Process onnection code 4 163(6.41) For Process onnection code 8 and 9 5(0.19) 20(0.78) 176(6.92) φ6(0.24) F02E.EPS Terminal onfiguration Terminal Wiring + SUPPLY Power supply and output terminal HEK + External indicator(ammeter) terminal *2 ommunication Terminals(T200 etc.) onnection hook SUPPLY HEK HEK ETER onnection hook *2 Ground terminal *2: When using an external indicator or a check meter, the internal resistance must be 10 or less. Not available for Fieldbus communication (Output signal code F and G). F03E.EPS GS 0121F01-02E June 01,

9 9 SELETION GUIE pplication ifferential Pressure Flow ifferential Pressure & Liquid Level with Remote Seals Type Traditional-ounting *1 Integral Orifice Extended Flush ombination raft Traditional-ounting *1 ifferential Pressure & Liquid Level Liquid Level, losed or Open Tank bsolute (vacuum) Pressure Gauge Pressure Gauge Pressure with Remote Seal Gauge Pressure with Remote Seal High Gauge bsolute & Gauge Pressure *3 Traditional-ounting *1 Flush Extended Traditional-ounting *1 Traditional-ounting *1 Extended Flush Traditional-ounting *1 irect-ounting odel EJ110 EJ115 EJ118N EJ118W EJ118Y EJ120 EJ130 EJ210 EJ220 EJ310 EJ430 EJ438N EJ438W EJ440 EJ510 EJ530 apsule L HV L H H E H H easurement Span kpa inh 2 O 0.5 to 10 2 to 40 1 to to to to to 14Pa 20 to 2000 psi 1 to 10 2 to to to to to 40 8 to to to to to to 4 1 to to to to 500 L 0.67 to 10 *2 1.3 to 130 * to 3 Pa * to 3 Pa 0.14 to 14 Pa 0.06 to 3 Pa 0.46 to 7 Pa 0.06 to 3 Pa 0.46 to 14 Pa 5 to 32 Pa 5 to 50 Pa 10 to to 2 Pa 0.5 to 10 Pa 5 to 50 Pa 4 to to to to to 40 * to 38 inhg *2 4.3 to 430 psi *2 4.3 to 430 psi 20 to 2000 psi 8.6 to 430 psi 66 to 1000 psi 8.6 to 430 psi 66 to 2000 psi 720 to 4500 psi 720 to 7200 psi 1.45 to 29 psi 14.5 to 290 psi 72.5 to 1450 psi 720 to 7200 psi aximum Working Pressure Pa psi 16 * * ased on Flange Rating 50 kpa ased on Flange Rating 10 kpa * kpa *2 430 *2 130 kpa *2 40 in H *2 O* ased on Flange Rating ased on Flange Rating kpa *1: Traditional-mounting is 1/4-18 NPTF process connections ( 1/2-14 NPTF with process adapters ) on 2-1/8" centers. *2: easurement values in absolute. *3: easurement values in absolute for EJ510. *4: When combined with Wetted parts material code H,, T,,, and, the value is 3.5 Pa (500 psi) T06E.EPS < Ordering Information > Specify the following when ordering 1. odel, suffix codes, and optional codes 2. alibration range and units: 1) alibration range can be specified with range value specifications up to 5 digits (excluding any decimal point) for low or high range limits within the range of to ) Specify only one unit from the table, Settings when shipped. 3. Select linear or square root for output mode and display mode. Note: If not specified, the instrument is shipped set for linear mode. 4. Select normal or reverse for operation mode Note: If not specified, the instrument is shipped in normal operation mode. 5. isplay scale and units (for transmitters equipped with integral indicator only) Specify either 0 to 100 % or engineering unit scale and and Unit for engineering units scale: Scale range can be specified with range limit specifications up to 5 digits (excluding any decimal point) for low or high range limits within the range of to Tag Number (if required) Subject to change without notice. GS 0121F01-02E ar. 23,