Product Selector Guide Appliance Power Supply ICs

Transcription

1 Product elector Guide Appliance Power upply ICs July 2011

2 Product elector Guide Power Products to upport Low tandby and No-Load Operation Isolated Flyback Main, Bias, or tandby upply CAPZero / ENZero TOPwitch-JX AC-C PI-miniappliancechart Non-Isolated Buck or Buck-Boost Linkwitch-TN 2.5 W W 10 W 25 W 0 W 5 W 5 W 40 W 45 W 50 W 75 W 90 W 100 W 150 W 250 W 500 W 1000 W 1500 W 000 W Output Characteristic (Wide Input ) Loose CV No OPTO LNK584 LNK562 LNK TNY 274 CV ±5% No OPTO LNK KEY Linkwitch-LP Linkwitch-CV Linkwitch-AX Tinywitch-III Linkwitch-XT CV ±2% OPTO LNK LNK62 64 TNY274 0 W 1 W 1.9 W 2.5 W.0 W 4.7 W 6 W 6.5 W 8 W 8.9 W 10 W 11.5 W 15 W 18 W 21.5 W 25 W 28.5 W ENZero and CAPZero can be used on any power applications as energy saving devices. IC Product Tables and esign Examples Very Low Power AC-C, Non-Isolated Linear/Passive upply Replacement ( 60 ma) Product 4 Output Current 1 (ma) Output Current 1 (ma) MCM 2 CCM MCM 2 CCM Linkwitch-TN 20 ± 15% LNK02P/G/ LNK04P/G/ LNK05P/G/ LNK06P/G/ V internal MOFET rating elf-powered ON/OFF control Hysteretic thermal shutdown Power limiting Frequency jitter reduces EMI Ecomart TM low standby/no-load power consumption 1. Typical output current in a non-isolated buck converter. Output power capability depends on respective output voltage. 2. Mostly discontinuous conduction mode.. conduction mode. 4. Packages: P: IP-8B, G: M-8B, : O-8C. Very Low Power AC-C Power Conversion (Up to 17 W) Product Adapter 1 Frame 2 Adapter 1 Frame 2 Linkwitch-CV 20 ± 15% LNK62P/ LNK624P/ LNK625P/ LNK626P/ Linkwitch-LP 20 ± 15% LNK562P/G/ LNK56P/G/ LNK564P/G/ LinkZero-AX 20 ± 15% LNK584G LNK584 LNK585G LNK LNK586G 6 5 LNK Linkwitch-XT 20 ± 15% LNK62P/G/ LNK6P/G/ LNK64P/G/ Minimum continuous power in a typical non-ventilated enclosed adapter measured at 50 C ambient. 2. Minimum practical continuous power in an open frame design with adequate heat sinking, measured at 50 C ambient.. Packages: P: IP-8B, P: IP-8C, G: M-8B, : O-8C. 700 V internal MOFET rating elf-powered ON/OFF control Hysteretic overtemperature protection Power limiting Frequency jitter reduces EMI Ecomart low standby/no-load power consumption

3 Low Power AC-C Power Conversion (Up to 6.5 W) Product Adapter 1 Adapter Frame 1 2 Frame 2 Tinywitch-III 20 ± 15% TNY274P/G TNY275P/G TNY276P/G TNY277P/G TNY278P/G TNY279P/G TNY280P/G V internal MOFET rating elf-powered Hysteretic overtemperature protection Frequency jitter reduces EMI Ecomart low standby/no-load power consumption On-time extension Latching output overvoltage protection Line undervoltage (UV) lockout electable current limit 1. Minimum continuous power in a typical non-ventilated encased adapter with minimal heat sinking, measured at a device ambient of 50 C. 2. Minimum continuous power in an open frame with adequate heat sinking. Tinywitch-III operates without bias winding.. Packages: P: IP-8C, G: M-8C. High Efficiency AC-C Power Conversion (Up to 244 W) PCB Copper Area 1 Product 5 Adapter 2 (W) Adapter 2 (W) TOPwitch-JX 20 ± 15% TOP264V TOP264K TOP265V TOP265K TOP266V TOP266K TOP267V TOP267K TOP268V TOP268K TOP269V TOP269K TOP270V TOP270K TOP271V TOP271K Metal Heat ink 1 Product 5 Adapter 2 (W) Adapter 2 (W) TOPwitch-JX 20 ±15% TOP264E/V TOP265E/V TOP266E/V TOP267E/V TOP268E/V TOP269E/V TOP270E/V TOP271E/V Multi-mode operation maximizes efficiency at all loads eip -12 package - Low profile horizontal orientation for ultra-slim designs - Heat transfer to both PCB and heat sink - Optional external heat sink provides thermal impedance equivalent to a TO-220 eip -12 package - Vertical orientation for minimum PCB footprint - imple heat sink mounting using clip provides thermal impedance equivalent to a TO-220 eop -12 package - 66 W universal input output power capability - Low profile surface mounted for ultra-slim designs - Heat transfer to PCB via exposed pad and OURCE pins - upports wave or reflow soldering Output overvoltage protection is user programmable for latching/non-latching shutdown with fast AC reset - Allows both primary and secondary sensing Line undervoltage detection prevents turn-off glitches Line overvoltage shutdown extends line surge limit Accurate programmable current limit Optimized line feed-forward for line ripple rejection 12 khz frequency reduces transformer and power supply size - Half frequency option for video applications Frequency jittering reduces EMI filter cost Improved auto-restart delivers <% of maximum power in short circuit and open loop fault conditions Accurate hysteretic thermal shutdown function automatically recovers Fully integrated soft-start for minimum start-up stress 1. ee Key Application Considerations section for more details. 2. Minimum continuous power in a typical non-ventilated enclosed adapter measured at +50 C ambient temperature.. Minimum continuous power in an open frame design at +50 C ambient temperature or 110/115 with doubler. 5. Packages:E: eip-7c, V: eip-12, K: eop-12. Zero 1 Loss Automatic X Capacitor ischarge IC Product BV Max Total X Capacitance CAPZero CAP002 CAP012 CAP00 CAP01 CAP004 CAP014 CAP005 CAP015 CAP006 CAP016 CAP007 CAP017 CAP008 CAP018 CAP009 CAP nf Total eries Resistance 2 ( + ) 1.5 MW 750 nf 1.02 MW 1 mf 780 kw 1.5 mf 480 kw 2 mf 60 kw 2.5 mf 00 kw.5 mf 200 kw 5 mf 150 kw Blocks current through X capacitor discharge resistors when AC voltage is connected Automatically discharges X capacitors through discharge resistors when AC is disconnected implifies EMI filter design larger X capacitor allows smaller inductive components with no change in consumption Only two terminals meets safety standards for use before or after system input fuse >4 mm creepage on package and PCB elf supplied no external bias required High common mode surge immunity no external ground connection High differential surge withstand internal MOFETs 1. IEC 6201 clause 4.5 rounds standby power use below 5 mw to zero. 2. Values are nominal. RC time constant is <1 second with ±20% X capacitor and ±5% resistance from these nominal values.. Package: : O-8.

4 Zero 1 Loss High Voltage ense ignal isconnect IC ENZero Product 2 Integrated isconnect MOFETs 20 Power Consumption in tandby EN012 2 <1 mw EN01 <1.5 mw 1. IEC 1601 clause 4.5 rounds standby power use below 5 mw to zero. 2. Package: : O-8. Eliminates significant standby losses - isconnects unnecessary circuit blocks during standby, remote-off, or light-load conditions Ultra-low leakage (maximum 1 ma) 6 MOFETs - <0.5 mw per channel during standby Linkwitch-TN Non-Isolated ual Output Buck (RK-18) 1., ±5 V, 50 ma, 7 V / 12 V, 80 ma, INPUT BUCK ERIVE POWER UPPLY L R 8.2 Ω 2.5 W µh BP C 12.4 kω 2.05 kω 2.2 mh L V, 80 ma +12 V µf Linkwitch-TN 4.7 µf LNK04N BYV26C 100 µf Q1 2N kω 1/8 W 20 Ω 1/8 W Q2 2N V N V BZX55V1 100 µf R5 5. 1/8 W -5 V, 50 ma PI V, +5 V, -5 V +12 V LinkZero-AX Non-Isolated, Zero tandby Consumption Power upply (ER-260) 1.5 W, 5 V, 00 ma, INPUT FLYBACK POWER UPPLY L 1 mh EE16 8 R8 220 pf 5.1 Ω 100 V L4 1.8 µh 56 µf 510 Ω 5 V, 00 ma kω R 10 Ω C9 0 nf µf. µf LinkZero-AX LNK584G BP/M 150 nf Ω Q1 MMBT Ω Ω Q2 MMBT904 W kω 0 20 kω P et 4 2 kω P Reset PI Linkwitch-CV Two-Output Constant Voltage Power upply (ER-21).8 W, 5 V, 0.15 A, 12 V, 0.25 A, INPUT FLYBACK POWER UPPLY 1 R 10 Ω µf 2200 µh µh 0 kω 00 Ω C 5 GP BP 1 6 B NC 7 B140 Linkwitch-CV E6 R5 1 LNK62PG 1 µf 8 6, kω R7 51 Ω 680 pf 100 V 0 µf L. uh PI V, 0.25 A 5 V, 0.15 A

5 Tinywitch-III Two-Output Residential Heating Control Power upply (I-12) 9.65 W, 5 V, 250 ma and 24 V, 50 ma, INPUT FLYBACK POWER UPPLY L N 1 A µh L Ω 4 pf R8 75 kω 100 Ω 8 F06 EN/UV BP/M µf , 9 EF20 Tinywitch-III TNY275PN 2 0 Ω Ω 1/ 470 pf 1 UF N5819 U2 P17A L4 L 0 µf U LM41 2% L, L4 and L5 are.5 mm 10 mm Ferrite beads µf 47 Ω 15 kω 0 R5. kω 26 PI V, 50 ma 5 V, 250 ma Tinywitch-III Air Conditioner Power upply (I-176) 20 W, 12 V, 1.6 A and 15 V, 50 ma, 200 C INPUT FLYBACK POWER UPPLY VC 82 kω 1 0 µf 4 10 nf 60V EN/UV BP C 50V EE Tinywitch-III TNY279PN U2B P17A UG4 4 UG4 UG2 470 µf 1000 µf 12 µh U2A P17A nf 2AC 0 µf 220 Ω 12 µh 2 A 1000 µf V BZX V 0.1 µf C9 0.1 µf 12 V, 1.6 A IO_ 15 V, 50 ma 700 Ω 1/ PRI_ PI TOPwitch-HX Condensing Boiler Power upply (I-144) 50 W (70 W Peak), 24 V, 2.08 A, INPUT FLYBACK POWER UPPLY 2.2 nf 2AC kω C4 22 nf V P6KE170A EE8 2 11,12 4 7,8 14 UG4 C µf. µh C2 24 V, 2.08 A 10 mh 275 R A t O µf 10 Ω 0.5 W 22 nf 60 V TOPwitch-HX U4 TOP258PN M CONTROL C 6.8 Ω uf U2B P17A 1 BAV kω W U2A P17A U TL41 2% Ω W C5 1.0 µf kω C6 1.0 µf 1 PI

6 TOPwitch-HX Refrigerator Power upply (ER-218) 100 W, 12 V, 8 A and 8 V, 0.4 A, INPUT FLYBACK POWER UPPLY 2.2 nf 2AC 47 Ω V P6KE200A 200 V 1 EE MB0100CT 1.5 µh 12 V, 8 A GBU8K 800 V 2 MΩ 100 kω 1 W C9. nf 4 MU , V 0 47 Ω 47 Ω MB0100CT U2 LM117 C µf 2200 µf 1500 µf 8 V, 0.4 A 6.2 mh L CMC Ferrite 150 µf. nf R5 2 MΩ R8 1 Ω kω Ω 4 UA PC57C 1 R A 1 1 MΩ 1/ 2 1 MΩ 1/ 6 0 nf KΩ 7 MU60 TOPwitch-HX V TOP260EN CONTROL X F C Ω UB PC57C 4 90 Ω kω 5 5. kω L N pf kω AC 1 U4 TL41 2% kω E PI CAPZero Active ischarging of the X Capacitor for Reduced tandby or No-load Power Consumption (RK-252) 2 A 90 kω RV1 20 CAPZero CAP014G A* 220 nf 275 V B 1 µf 275 V C* 2.2 µf 275 V 90 kω *A and C are not populated PI ENZero Zero Loss High Voltage ignal isconnect for Reduced tandby or Light-Load Power Consumption ystem V CC + ENZero EN01G ystem tandby ignal AC Input Control & rive High Voltage C PFC IC World Headquarters 5245 Hellyer Avenue, an Jose, CA 9518, UA, Main: Customer ervice Phone: , Fax: , info@powerint.com PI-5968a On the Web Power Integrations. Power Integrations, TOPwitch, Tinywitch, Linkwitch, PA-witch, Peakwitch, CAPZero, ENZero, LinkZero, HiperPF, HiperTF, HiperLC, Qspeed, Ecomart, Clampless, E-hield, Filterfuse, takfet, PI Expert and PI FACT and the Power Integrations logo are trademarks or registered trademarks of Power Integrations, Inc. All rights reserved.