Wireless Sensor Networks (aka, Active RFID)

Transcription

1 Politecnico di Milano Advanced Network Technologies Laboratory Wireless Sensor Networks (aka, Active RFID) Hardware and Hardware Abstractions Design Challenges/Guidelines/Opportunities 1

2 Let s start From the edge.. o A Sensor Node (or mote) is a device with the following capabilities: n Sensing external phenomena n Processing information n Storing information n Communicating with other motes or devices 2

3 Mote Architecture Storage Flash data logs pgm images Processing / Sampling microcontroller proc Data SRAM timers EPROM ADC Low-power Standby & Wakeup I/O Sensor Interface ADC Wireless Net Interface Wired Net Interface analog sensors digital sensors RF transceiver serial link USB,EN, antenna System Architecture Directions for Networked Sensors, Hill,. Szewcyk, Woo, Culler, Hollar, Pister, ASPLOS

4 o IoT Hardware offer is vast, fragmented and heterogeneous power IoT Hardware Breakdown n Type of CPU, connectivity, storage, sensing peripherals beagleboard RaspberryPI TelosB cost 4

5 Power Consumption o Sensor node has limited power source o Sensor node LIFETIME depends on BATTERY lifetime o Goal: Provide as much energy as possible at smallest cost/volume/weight/recharge o Problem: recharging and/or battery replacement may be immaterial or too expensive o Options n n Primary batteries not rechargeable Secondary batteries rechargeable, only makes sense in combination with some form of energy harvesting 5

6 POWER CONSUMPTION o Sensors can be a DATA ORIGINATOR or a DATA ROUTER. o Power conservation and power management at different levels are mandatory: n Power-aware communication n Low-power processing (and processors) n Low-power sensing 6

7 Energy Sources o How to Characterize a Battery n Voltage n Source current n Leakage n Voltage profile n Recharge o Battery Delivered Capacity n Measured in Ah n E.g.: 1000 [mah] means that battery is able to provide a current of 1000 [ma] for 1 hour, or of 1mA for 1000 hours (approx) Source: Lecture slides of Wireless Embedded Internetworking, Prof. D. Culler 7

8 Energy Scavenging o Solar (Outdoors) 15 mw/cm 2 (direct sun) o Solar (Indoors) n mw/cm 2 (office desk) n 0.57 mw/cm 2 (<60 W desk lamp) o Temperature Gradients 80 mw/cm 2 at about 1V from a 5Kelvin temp. difference o Vibrations 0.01 and 0.1 mw/cm 3 o Acoustic Noises 3*10 {-6} mw/cm 2 at 75dB - 9.6*10 {-4} mw/cm 2 at 100dB Source: Lecture slides of Sensor Networks, Prof. I. Akyildiz 8

9 Power Consumption Dissected RADIO 20 Power (mw) SENSOR CPU TX RX IDLE SLEEP General Design Guideline: To switch off the Radio (TX/RX/IDLE) as soon as possible Source: Lecture slides of Sensor Networks, Prof. I. Akyildiz 9

10 The Idle Listening Problem o The power consumption of short range (i.e., lowpower) wireless communications devices is roughly the same whether the radio is transmitting, receiving, or simply ON, listening for potential reception n includes IEEE , Zwave, Bluetooth, and the many variants n WiFi too! n Circuit power dominated by core, rather than large amplifiers o Radio must be ON (listening) in order receive anything. n Transmission is infrequent. n Listening (potentially) happens all the time Þ Total energy consumption dominated by idle listening 10

11 Power: Model of operation Active Active Sleep WakeUP Work Sleep WakeUP Work o o o o o Sleep Active [Wakeup / Work] Peak Power n MW in supercomputer, kw in server, Watts in PDA n milliwatts in mote class device Sleep power n Minimal running components + leakage n Microwatts in mote-class Average power n P ave = = (1-f active )*P sleep + f active *P active n P ave = f sleep *P sleep + f wakeup *P wakeup + f work *P work Lifetime n EnergyStore / (P ave - P gen ) Duty Cycle Source: Lecture slides of Wireless Embedded Internetworking, Prof. D. Culler 11

12 Power Consumption for Communication P = N [P (T + T ) + P (T )] + N [P (R + c T te on wu O on R re on R wu )] where P te is power consumed by transmitter P re is power consumed by receiver P O is output power of transmitter T on is transmitter on time R on is receiver on time T wu is start-up time for transmitter R wu is start-up time for receiver N T is the number of times transmitter is switched on per unit of time N R is the number of times receiver is switched on per unit of time 1 E. Shih et al., Physical Layer Driven Protocols and Algorithm Design for Energy-Efficient Wireless Sensor Networks, ACM MobiCom, Rome, July

13 On the emitted power o The emitted power is often a tunable parameter o Good practice is to set it to the lowest value which allows for good reception o The quality of the reception process is measured in terms of n n n Bit Error Rate (BER): fraction of bit not correctly received ( 1 for a 0 or viceversa) Packet Error Rate (PER): fraction of packet not correctly received PER/BER relation (packet of length l, independent errors): PER =1 (1 BER) l 13

14 Signal to noise and Interference Ratio o BER (and PER in turn) depends on the level of noise in the TX/RX channel, which, in turn, depends on the transmitted/received power Thermal noise: KTB o BER can be computed once given the specific TX/RX channel (modulation) and the specific SINR

15 Receiver Sensitivity o Each receiver is characterized by a sensitivity parameter (e.g. P min =-95dBm), n The minimum input signal power needed at receiver input to provide adequate SNR at receiver output to do data demodulation o Example: IEEE n Receiver sensitivity (packet error rate < 1%) o P min > GHz band o P min > /915 MHz band o Knowing such parameter, one can find the required emitted power at the transmitter by inverting the propagation law of the channel to get to required emitted power

16 Emitted power - Example o A wireless receiver is characterized by a sensitivity P r =-0.1[uW]; the transmitter is d=10[m] from the receiver; the TX-RX is performed at a carrier frequency f=2.4ghz; the propagation on the channel is characterized by the following model * P r = P t g t g r ( 4 d ) 2 o Further assuming the antenna gains equal to 1, we get a required emitted power P t = P r ( 4 d ) 2 100[mW ] *If you have no clue on where this model comes from you may want to have a look at the primer on wireless propagation available at the course web site 16

17 Wake-Up Overhead o Wake-Up comes with energy overhead o Question: n What is the consumed energy per bit for transmitting a packet of L [bits]? n Energy spent in transmission: E o =P o T L n Energy spent during wake-up: E wu =P te T wu n Energy spent for TX circuitry: E tx =P tx (T wu +T L ) n Energy per bit: (E wu +E o +E tx )/L 17

18 Wasted Energy o Parameters: R=1 Mbps; T WU ~ 450 msec, P te ~81mW; P out = 0 dbm 18

19 Sample Radio Data sheets 19

20 Processing Power Consumption o CPU power dissipation due to: P p = P dyn + P sc + P leak Job done Short circuits leakage n Where P dyn = CfV 2 n C: capacitance (~ 0.67nF) n f: frequency n V: voltage 20

21 Processing Power Consumptions o Rough Comparison: n Energy cost of transmitting 1 KB a distance of 100 m is approx. equal to executing 3 Million instructions by a 100 million instructions per second processor. o Local data processing (if possible) is crucial in minimizing power consumption in a multi-hop network Source: Lecture slides of Sensor Networks, Prof. I. Akyildiz 21

22 Multiple Power Consumption Modes o Multiple modes possible Deeper sleep modes o Strongly depends on hardware n TI MSP 430, e.g.: four different sleep modes n Atmel ATMega: six different modes Source: Lecture slides of Sensor Networks, Prof. I. Akyildiz 22

23 Optimize Power Consumption o Power aware computing n Ultra-low power microcontrollers n Dynamic power management HW n Dynamic voltage scaling (e.g Intel s PXA, Transmeta s Crusoe) n Components that switch off after some idle time 23

24 Memory Power Consumption o Crucial part: FLASH memory n Power for RAM almost negligible o FLASH writing/erasing is expensive n Example: FLASH on Mica motes n Reading: 1.1 nah per byte n Writing: 83.3 nah per byte Source: Lecture slides of Sensor Networks, Prof. I. Akyildiz 24

25 Design Guidelines o Do not run motes at full operation all the time n If nothing to do, switch to power safe mode n Question: When to throttle down? How to wake up again? o Typical modes n Controller: Active, idle, sleep n Radio mode: Turn on/off, transmitter/receiver, both Source: Lecture slides of Sensor Networks, Prof. I. Akyildiz 25

26 Optimize Power Consumption o Energy aware software n Power aware OS: dim displays, sleep on idle times, power aware scheduling o Energy aware packet forwarding n Radio automatically forwards packets at a lower level, while the rest of the node is asleep o Energy aware wireless communication n Exploit performance energy tradeoffs of the communication subsystem, better neighbor coordination, choice of modulation schemes 26

27 What About Sensing? o A unifying framework is missing: n Wide array of low-power micro sensors available (Temp, Light, Humidity, Acceleration, Mag, Pressure, ) n Several digital interfaces (RS232, SPI, I2C, ) n Several Analog Interfaces o Design and integration with other components are critical 27