GP1F31T/R, GP1F32T/R, GP1F33TT/RR/RT, GP1C331/331A/332/333/334/335

Transcription

1 GPFT/R, GPFT/R, GPFTT/RR/RT, GPC/A//// GPFT/R, GPFT/R, GPFTT/RR/RT, GPC/A//// Features. Low jitter ( : TYP. ). High speed tramission (8Mbps, NRZ ). Directly connectable to modulation /demoduration for digital audio equipment Fiber optic... Built-in light emitting diode driving Fiber optic receiver... Built-in processing. With two fixing holes for easy mounting on set panel GPFT/GPFR/GPFRR/ ( GPFTT/RT ). -channel type (GPFRR/GPFTT/GPFRT) * Sharp's optical fiber cables, (GPC, GPCA, GPC, GPC, GPC, GPC) are recommended The model marked with may not be available in the near future. Contact Sharp sales personnel for details before use Applicatio. CD players. BS tuners. Digital amplifiers Fiber Optic Tramitting /Receiving Units Outline Dimeio GPFT/GPFR GPFT/GPFR φ. fixing hole φ Depth (Shield case sec.) GPFT r (Resin sec.) Protection cap 0. GPFR Protection cap.7 φ. fixing hole φ (Unit : mm). Detector Amp. V out OP light detector (.) GPFT GPFR r Detector Amp. V out OP light detector OP (Optical ) is a trademark of the SHARP Corporation. An OP coists of a light-detecting element and processing integrated onto a chip. Notice Internet In the absence of confirmation by device specification sheets, SHARP takes no respoibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet address for Electronic Components Group

2 GPFT/R, GPFT/R, GPFTT/RR/RT, GPC/A//// Model Line-ups Absolute Maximum Ratings (Ta= C) Parameter Symbol Rating Unit Supply voltage voltage Power dissipation High level output current Low level output current * * * * Vcc Vin P IOH IOL 0. to to VCC+0. V V mw ma ma Operating temperature * 0 to +0 C Topr *7 0 to +70 C Storage temperature Soldering temperature Tstg Tsol 0 to C C * * * Model No. GPFT GPFR GPFT GPFR GPFTT GPFRR GPFRT GPC GPCA GPC GPC GPC GPC Internal Cotitution Fiber optic Fiber optic receiver Fiber optic Fiber optic receiver Fiber optic (-channel) Fiber optic receiver (-channel) Fiber optic /receiver Fiber optic cable (m) Fiber optic cable (0.m) Fiber optic cable (m) Fiber optic cable (m) Fiber optic cable (m) Fiber optic cable (m) * Source current * Sink current * seconds/ times or less * GPFT/GPFT/GPFTT/Tramitting portion of GPFRT * GPFR/GPFR/GPFRR/Receiving portion of GPFRT * GPFT/GPFR *7 GPFT/GPFR/GPFTT, GPFRR, GPFRT Fiber Optic Cable (GPC, GPCA, GPC, GPC, GPC, GPC) (Ta= C) Parameter Symbol Rating Unit Tpf 0 N Tf 0 N R MIN. mm Plug & optical fiber Teion Optical fiber Bending radius Operating temperature Storage temperature Topr Tstg 0 to to +70 C C Outline Dimeio GPFTT/GPFRR GPFRT φ. fixing hole φ Depth GPFTT,,,,,, V out V out.0 Protection cap P P P P P=. (Lead root dimeion) GPFRR GPFRT Fiber optic cable (GPC). 0. MAX Terminal arrangement Receiver L=000 φ. ; GaAlAs ; silicon 8.0 Receiving portion 0.µF.7µF φ. fixing hole φ Tramitting portion Receiving portion Internal equivalent 0.µF.7µF OP light detector OP light detector 0.µF.0 ; GaAlAs ; silicon OP light detector Tramitter 0.µF ; GaAlAs ; silicon.0 0.µF 0.µF.7µF Tramitting portion VIEW A VIEW A / -C -C C. Model No. Dimeio GPC GPCA GPC 000 GPC 000 GPC 000 GPC 000

3 GPFT/R, GPFT/R, GPFTT/RR/RT, GPC/A//// Electro-optical Characteristics() Tramitter GPFT/GPFT/GPFTT/Tramitting portion of GPFRT Parameter Symbol Conditio MIN. TYP. MAX. Unit Operating voltage VCC V Peak emission wavelength λp nm Optical power output coupling with fiber PC Refer to Fig. 7 dbm Dissipation current Icc Refer to Fig. 0 ma High level input voltage ViH Refer to Fig. V Low level input voltage ViL Refer to Fig. 0.8 V Low High propagation delay time tplh Refer to Fig. 00 High Low propagation delay time tphl Refer to Fig. 00 Pulse width distortion tw Refer to Fig. (0)** +(+0)** Jitter Operating trafer rate T Refer to Fig. (0)** 8 Mbps ** Value in parenthesis : GPFT Electro-optical Characteristics() Receiver GPFR/GPFR/GPFRR/Receiving portion of GPFRT (Ta= C) (Ta= C) Parameter Symbol Conditio MIN. TYP. MAX. Unit Operating voltage VCC V Peak seitivity wavelength λp 700 nm Maximum input optical power level for receiving unit Minimum input optical power level for receiving unit AX IN Refer to Fig. Refer to Fig.. dbm dbm Dissipation current Icc Refer to Fig. 0 ma High level output voltage Low level output voltage Rise time Fall time Low High propagation delay time High Low propagation delay time Pulse width distortion VOH VOL tr tf tplh tphl tw V V Jitter Refer to Fig.8, PC=dBm 0 Refer to Fig.8, PC=dBm 0 Operating trafer rate T NRZ. duty input 0. 8 Mbps Electro-optical Characteristics() Fiber Optic Cable Parameter Symbol MIN. TYP. MAX. Unit Optical output coupling fiber PC 7 dbm Refracting ratio distribution Step index

4 Mechanical Characteristics GPFT/R, GPFT/R, GPFTT/RR/RT, GPC/A//// Parameter Symbol Conditio MIN. TYP. MAX. Unit Iertion force, In compliance with EIAJ RC-70 0 withdrawal force Initial value when a square connector in used. N Fig. Measuring Method of Optical Output Coupling With Fiber GPFT/GPFT/ GPFTT Optical power meter (Anritsu)ML9B Notes () VCC=.0±0.0V(Operating) () To bundle up the standard fiber cable, make it into a loop with the diameter (D) of 0cm or more. D The optical power meter must be calibrated to have the wavelength seitivity of 0nm. (0dBm=mW) Fig. Voltage/Power Dissipation Measuring method GPFT/GPFT/ GPFTT/GPFRT Sample I CC fiber cable Light power meter (Anritsu) ML9B Light power meter should be corrected to wavelength seitivity (0nm) (0dBm=mW) condition and measuring method condition Vin=.0V or more Vin=0.8V or less Note () VCC=.0±0.0V (ON-State) Measuring method <=PC<=dBm, C=0mA or less PC<=dBm, C=0mA or less

5 Fig. Pulse Respoe Measuring Method GPFT/R, GPFT/R, GPFTT/RR/RT, GPC/A//// GPFT/GPFT/ GPFTT/GPFRT receiver Output Mbps NRZ 00 successive pattern Oscilloscope CH CH GPFT/GPFT GPFTT/GPFRT (CH) receiver Output (CH) t PLH t PHL Pulse width distortion tw=t PHL t PLH Notes () VCC=.0±0.0V (Operating) () The probe for the oscilloscope must be more than MΩ and less than 0pF. Fig. Measuring Method of Jitter GPFT/GPFT/ GPFTT/GPFRT receiver Output 0 0 Mbps biphase mark PRBS CH CH Oscilloscope Trigger : CH Storage mode receiver output Notes () The waveform write time shall be seconds. But do not allow the waveform to be distorted by increasing the brightness too much. () VCC=.0±0.0V (Operating) () The probe for the oscilloscope must be more than MΩ and less than 0pF.

6 GPFT/R, GPFT/R, GPFTT/RR/RT, GPC/A//// Fig. Muximum Optical Power Level/Minimum Optical Power Level Measuring Method of Receiving Unit Variable optical attenuator GPFR/GPFR GPFRR/GPFRT Notes () Optical power meter must be calibrated to have the wavelength seitivity of 0nm. () With no optical attenuator connected, use the GPFT/GPFT/GPFTT and the fiber optic cable GPC with the fiber coupling light output set at dbm/dbm. Optical power meter Anritsu : ML9B Fig. Measuring Method of Dissipation Current VCC=.0±0.0V PC=dBm Mbps NRZ, duty or Mbps biphase PRBS GPFR/GPFR GPFRR/GPFRT A Ammeter V out (DC average current value) Fig.7 Measuring Method of Output Voltage and Pulse Mbps NRZ, duty V GPFR/GPFR/ GPFRR/GPFRT Vcc V out R so CH CH R si Oscilloscope (CH) V OH GPFR/GPFR GPFRR/GPFRT Output (CH) t r t f 90% Notes () VCC :.0±0.0V (Operating) () The probe for the oscilloscope must be more than MΩ and less than 0pF. () Rsi, Rso ; load resistrance (Rsi :.kω, Rso :.kω) V OL 0% t PLH t PHL

7 Fig.8 Measuring Method of Jitter GPFT/R, GPFT/R, GPFTT/RR/RT, GPC/A//// GPFT/GPFT/ GPFTT Tramitter GPFR/GPFR/ GPFRR/GPFRT V out R so V R si 0 0 Mbps biphase PRBS CH CH Oscilloscope Trigger : CH Storage mode Sweep : AUTO/NORM GPFR output GPFR output GPFRR output GPFRT output Notes () Rsi Rso : Strandard load resistance (Rsi :.Ω Rso :.kω) () VCC=.0±0.0V (Operating) () Set the oscilloscope to be storage mode and write time to seconds. Do not allow the waveform to be distorted by icreasing the brightness too much. () The probe for oscilloscope must be more than MΩ and less than 0pF. Fig.9 Measuring Method of Optical Output Coupling With Fiber Optical power meter Anritsu ML9B light : Light that provides the fiber-end optical output of dbm±0.dbm when the standard fiber optic cable is connected.

8 Fig.0 System Configuration Example GPFT/R, GPFT/R, GPFTT/RR/RT, GPC/A//// CD/DAT/BS Tuner Modulation (LZ9F9) Digital Amp. Demodulation (LZ9F9) Light emitter Fiber optic GPFT/ GPFT Fiber optic cable GPC Signal processing Fiber optic recelver GPFR/GPFR BS tuner Modulation (LZ9F9) Fiber optic cable GPC Digital Amp. Demodulation (LZ9F9) Fiber optic GPFTT Modulation (LZ9F9) Light emitter Light emitter Fiber optic cable GPC Signal processing Light detector Signal processing Light detector LZ9F9 is Sharp s modulation/demodulation. Demodulation (LZ9F9) Fiber optic receiver GPFR GPFR In addition, you can also choose the following system configuration according to your application. GPFTT GPC GPFRR GPFRT GPC GPFRT Precautio for Use Please refer to the chapter "Precautio for Use"

9 Application Circuits NOTE The application examples in this publication are provided to explain representative applicatio of SHARP devices and are not intended to guarantee any design or licee any intellectual property rights. SHARP takes no respoibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specificatio, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locatio are also subject to change without notice. Observe the following points when using any devices in this publication. SHARP takes no respoibility for damage caused by improper use of the devices which does not meet the conditio and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditio: (i) The devices in this publication are designed for use in general electronic equipment desig such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Coumer electronics (ii)measures such as fail-safe function and redundant design should be taken to eure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Traportation control and safety equipment (i.e., aircraft, trai, automobiles, etc.) --- Traffic s --- Gas leakage seor breakers --- Alarm equipment --- Various safety devices, etc. (iii)sharp devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applicatio --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). Contact a SHARP representative in advance when intending to use SHARP devices for any "specific" applicatio other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or tramitted in any form or by any mea, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. Contact and coult with a SHARP representative if there are any questio about the contents of this publication.