Industrial Applications

Transcription

1 Model: Industrial Applications Product Name: Smart Receiver (Mk2) RoHS Compliant Product Code: SR2 The sr-2 is the second generation of the Hanwell Smart Receiver. It is a network enabled receiver, designed for collecting environmental monitoring data from multiple points within a site, or across multiple sites. In addition, it can be upgraded to a transceiver which both receives and retransmits the data. It uses standard TCP/IP communications protocols for speedy data handling. The network traffic generated is very low and data is automatically sorted and filed. This multipoint operation can be further expanded, with the use of optional GPRS, and used on a larger national or international basis. See the diagram overleaf for some potential ways of using the sr-2, or contact Hanwell to discuss your site specific requirements. In addition to receiving data from the rl-2000, rl-4000, rl-5000 and rl-8000 ranges of sensors, the unit can also read hard-wired sensors and, optionally, be fitted with up to eight on-board probes. Each sr-2 can handle data from up to 253 sensors, and up to 16 sr-2s can be run on a single system bringing it to a total of 4048 sensors. The sr-2 supports Hanwell s standard and extended transmission data formats. The sr-2 logs all received data in its on-board 512kb memory. The Radiolog software continually interrogates the sr-2 for the most recent data, and downloads the data according to user-defined logging periods to the server or operating PC. Software users can view live and historic data, produce out of spec and summary reports and set alarms on both the data levels and the rate of change. In addition to the data readings from the sensors, the sr-2 can log the corresponding Received Radio Signal Indicators (RSSI) which reveal the strength of radio reception of each Sensor. As well as being logged, the RSSI is indicated on the front LCD along with other status information. An optional remote Receiver can be connected to improve radio reception in difficult areas. The sr-2 is designed to be in constant communication with the software but has user-configurable fallback behaviour in the event of network or power failure. An on-board battery provides a UPS with 2.3A/hour life to carry it through up to 12 hours power disruption (larger external UPSs are available as an optional extra). Alarm relays are included: these can indicate that the readings are out of specification, and can be optionally set to indicate a network failure. A MS BUS connection allows the sr-2 to drive the Hanwell MS1000 environmental control system. See diagram overleaf Transmitter 1 Not available in US, 2 US only Dimensions Weight Power Supply Options Case Material(s) Operating Humidity Range Operating Temperature Range 300 x 200 x 85mm 1.2kg 110V AC or 240V AC. On-board 12V battery back-up supplying 2.3A/hr Powder coated mild steel 10 90% RH, non-condensing 5 40C (Temperature compensated range) Radio Specification FF 1 F1 1 SF 1 HP 2 Radio Frequency MHz MHz to MHz in 25 KHz increments Synthesized Radio Power 10mW 10mW 10mW Programmable Radio Range 2 miles over open ground Outputs Alarm Outputs 1 x nominal 12V, 2 x changeover relays (energised when no alarms exist) MSBUS 4 core signal cable Accessories (e.g. mounting brackets, remote probe etc) Codes RX-xx Y Y Y ABR12/24 SR2-E-7.0-UPS SR2-E-15-UPS Description Remote receiver please specify the frequency required Thermistor probe on 5m cable with bare ends suitable for wiring into the sr-2 s on-board probe inputs Humidity probe on 5m cable with bare ends, as above. Combined thermistor & RH probe on 5m cable with bare ends, as above Alarm beacon, red strobe, 12/24V with bracket and 2m cable 7.0Ah external wall mounted UPS 15Ah external wall mounted UPS Instrumentation for Science and Industry ISI sa-nv Rue du Doyenné 3 Dekenijstraat 1180 Brussels Tel +32 (0) web : mail : sales@isi-be.com

2 Radiologger - Transmitter rl5001 radio transmitter Product Code Series RL5001-xxx rl Not available in US 2 Only available in US Typical Applications Environmental monitoring Warehouse monitoring Pharmaceutical monitoring Laboratory monitoring Building monitoring & control Event logging T emporary monitoring New from Hanwell is the rl5000 dp radiotelemetry transmitter, designed for use withthe Radiolog 8 environmental monitoringsystem. The units are in IP65-rated cases andare suitable for use in tough environments. Utilising an integral temperature compensated pressure sensor the rl5000 differential pressure transmitter delivers exceptional performance. The sensor utilises a silicon, micro machined, stress concentration enhanced structure to provide a very linear output to the measured pressure. The ports are designed with matched dead volumes. This series is intended for use with non-corrosive, nonionic working fluids such as clean dry air, dry gases and the like. pressure sensor when disconnecting for calibration. The transmitter is typically powered by a 7.5V 2700mAh battery or 2 x Lithium C size 5 Ah that can be fitted by the user. The battery life will be dependant on the transmission speed. Larger battery packs are available, local power input is also an option. An indicator on the LCD will warn when the battery is low, and the transmitter maintains a record of when the battery has been changed. The rl-5000 range has been designed to comply with the RoHS and WEEE EU directives, and carries the CE mark. Instrument Dimensions: 197 x 106 x 60mm Weight: 300 grams Case Material: ABS Power Supply: 7.5V 2700mAh or 2 x Lithium C size Op. Humidity Range: 0 95% RH, non-condensing Op. Temp. Range: -20 C to +60 C Sensors Code RL5001 Description Thermistor, PT100, Humidity, Linear Radio *Radio Frequency: Fixed frequency modules MHz MHz Synthesised modules to MHz in 25KHz increments MHz 2 Radio power: 10 mw Radio range: 3 km over open ground The media wetted materials are the silicon diaphragm, glass filled nylon, RTV and alumina ceramic. The transmitter ID, transmission speed and calibration data is programmed into its onboard memory using Radiolog 8, a software package which automatically recognises the type of unit connected to the PC via the USB lead. Fitted with a custom-designed LCD to indicate current readings, battery life remaining and alarm conditions. There is an instantaneous display update button located on the front panel. Pressure connections are made via quick release Lemo pressure connectors, which avoid damage to the Communications & Software PC/Logger Interface: Standard USB A/ USB mini-b PC Software: 32bit Windows with Radiolog 8.3 or later Minimum O/S: Windows 2000, Windows XP, Windows NT Accessories Code Y055 W250 USB communications lead USB configuration tool (required for users with Radiolog software earlier than 8.3) ISI sa-nv - Instrumentation for Science and Industry (INTERCONTINENTAL SERVICES INC) Rue du Doyenné 3 Dekenijstraat 1180 Brussels Belgium - Tel 02/ Fax mail : sales@isi-be.com web :

3 Isolate mains supply before removing this cover. Live parts enclosed. Isolate mains supply before removing this cover. Live parts enclosed. Isolate mains supply before removing this cover. Live parts enclosed. Model: Industrial Applications Product Name: Smart Receiver (Mk2) Product Code: SR2 Local Site One or more sr-2 s on a main site connected via LAN points LAN Network Server Collects data from all sr-2 s and is interrogared by Network Users Remote Sites One or more sr-2 s from remote sites via LAN or WAN, for example, off-site Network User For example, main system administrator LAN or WAN Network User For example, someone needing weekly reports Remote Sites Non-networked site connected via modem Network User For example, a home worker Modem Interface One system can comprise up to 16 separate sites but all data is treated the same way. Instrumentation for Science and Industry ISI sa-nv Rue du Doyenné 3 Dekenijstraat 1180 Brussels Tel +32 (0) web : mail : sales@isi-be.com

4 Radiologger - Transmitter Single channel thermistor Product Code Series RL * & RL * rl4000 The rl4001 & rl4002 are precision thermistor temperature measuring and radio transmission devices. The rl4001 has a single channel the rl4002 is dual channel. The sensors are connected via 2 pin Lemo plugs and sockets. They allow wire-free monitoring of a site, with real time alarm notification and historical analysis of data. Each 4000 unit reads its on-board sensors providing accurate and reliable information about environmental conditions. This data is transmitted, at user-defined intervals, to the Radiolog system where it is filed for analysis. rl4000 series transmitters can be used in accordance with GAMP and FDA regulations. The transmitters and sensors can be calibrated by the either user or Hanwell staff on-site or at Hanwell s in-house calibration laboratory. Transmitter ID number and transmission rate are set in the transmitter using a simple software program (free to download) and a USB cable. Each unit has an LCD screen simultaneously displaying the most recent readings taken and the predicted battery life.the transmitter is powered by a single 3.6V AA Lithium battery, which can be fitted by the user. The battery life will be dependent on the transmission rate set. An indicator on the LCD will warn when the battery is low, and the transmitter maintains a Above: Detail of USB socket Below: Optional wall mounting security bracket record of when the battery was last changed. Each 4000 series radio transmitter has enough internal memory to store up to readings and is in fact continually logging guaranteeing 100% validity of the data. The 4000 series unit can be downloaded via the high speed USB connection directly into the PC software (V8.4 or later only). The data logged will be added to the radio data, providing a continuous history for that transmitter. The moulded case allows easy access to the battery and USB socket, as well as having slots to fit onto secure wall brackets. CFR21 part 11 compliant software is available. OQ & IQ templates are included, full on-site validation services are available. The 4000 range has been designed to comply with the RoHS and WEEE EU directives, and carries the CE mark. Typical Applications Monitoring in: Fridge/Freezer monitoring Laboratories Hospitals Pharmaceutical Warehousing Instrument Dimensions: 110 x 80 x 35mm Weight: 200 grams Power Supply: 3.6 Volt AA Lithium battery Battery Life: 18 months Case Materials: ABS & PC Operating Humidity Range: 0 100% non-condensing Operating Temp Range: -20 to +60 C Memory Capacity: readings Sensors Temperature Sensor: Range: Accuracy: Resolution: Precision thermistor -40 to +70 C +/- 0.1 C between -25 C to +50 C +/-0.3 elsewhere 0.1 C Radio *Radio Frequency: MHz MHz (fixed) MHz in 25KHz increments (synthesised) Radio Power: 10 mw Radio Range: 3 km over open ground Accessories Code: Y119 Y055 G129 CAL-T CAL-T-LOW CAL-T-2 CAL-T-LOW-2 Wall mounting security bracket Setup communications cable Replacement 3.6V Lithium AA battery 3 point calibration between -20 and +110C (single Ch) 3 point calibration between -90 and +110C (single Ch) 3 point calibration between -20 and +110C (dual Ch) 3 point calibration between -90 and +110C (dual Ch) Instrumentation for Science and Industry ISI sa-nv Rue du Doyenné 3 Dekenijstraat 1180 Brussels Tel +32 (0) web : mail : sales@isi-be.com

5 Radiologger - Transmitter Temperature & humidity Product Code Series RL4106 rl4000 The rl4106 radio transmitter is one of a new range of advanced temperature and humidity radio transmitters. They allow wire-free monitoring of a site, with real time alarm notification and historical analysis of data. Each rl4106 unit reads its on-board sensors to provide accurate and reliable information about environmental conditions. This data is transmitted, at user-defined intervals, to the Radiolog for Museums system where it is filed for analysis. The rl4106 has two sensors as standard: a precision temperature probe and a high quality humidity probe. These sensors can be mounted internally to the transmitter body, externally on the case or remotely on a probe. An additional surface temperature probe can be added to check the dewpoint margins. These sensors can be calibrated by the users or at Hanwell s in-house calibration laboratory. The ID number and transmission rate are set in the rl4106 using a simple software program (free to download) and a USB cable. Each unit has an LCD screen simultaneously displaying the most recent readings taken and the predicted battery life. Above: Detail of USB socket Below: Optional wall mounting security bracket the battery is low, and the rl4106 maintains a record of when the battery was last changed. The moulded case allows easy access to the battery and USB socket, as well as having slots to fit onto secure wall brackets and a plain front panel to hide the LCD if more discreet monitoring of public areas is desired. The rl4000 range has been designed to comply with the RoHS and WEEE EU directives, and carries the CE mark. Typical Applications Monitoring in: Hospitals Pharmaceutical Warehousing Instrument Dimensions: 110 x 80 x 35mm Weight: 200 grams Power Supply: 3.6 Volt AA Lithium battery Battery Life: 18 months Case Materials: ABS & PC Operating Humidity Range: 0 to 100% non-condensing Operating Temp Range: -15 to +65 C Memory Capacity: readings Sensors Temperature Sensor: Range: Accuracy: Resolution: Humidity Sensor: Range: Accuracy: Resolution: Precision thermistor -15 to +65 C +/- 0.2 C between -15 C to +65 C 0.1 C Capacitive polymer 0 to 100% non-condensing +/- 0.2 C 0.1 C Radio *Radio Frequency: MHz MHz (fixed) MHz in 25KHz increments (synthesised) Radio Power: 10 mw Radio Range: 3 km over open ground Accessories Code: Y119 Y055 G129 Wall mounting security bracket Setup communications cable Replacement 3.6V Lithium AA battery The rl4106 is powered by a single 3.6V AA Lithium battery, which can be fitted by the user. The battery life will be dependent on the transmission rate set. An indicator on the LCD will warn when ISI sa-nv - Instrumentation for Science and Industry (INTERCONTINENTAL SERVICES INC) Rue du Doyenné 3 Dekenijstraat 1180 Brussels Belgium - Tel 02/ Fax mail : sales@isi-be.com web :

6 Instrumentation for Science and Industry ISI sa-nv Rue du Doyenné Brussels Tel +32 (0) Fax 02/ web : mail : sales@isi-be.com

7 i S E N S E G P R S T R A N S M I T T E R isense GPRS Transmitter Evolved from Hanwells existing range of established radio logging products the isense is an innovative self contained unit enabling remote monitoring of diverse parameters via wireless GPRS technology. Locations that previously seemed inaccessible including, buildings, machinery, infrastructure or vehicles can now easily be accessed and monitored. A number of different sensors can be attached to the isense in order to monitor parameters such as energy, temperature, pressure, structural stress and many more. This real-time information is then transmitted via GPRS to a central database, and can be accessed immediately on a PC for viewing, recording and assessment. Features: Completely self contained (battery operated) Date and time stamped monitoring Up to five year battery life Transmit rate increase on event Remote setup options Data stored in non volatile memory All data recovered in the event of temporary GPRS coverage problems Easy to understand journey profile information Works with a range of sensor families Technical Summary Instrument Dimensions: 100 x 100 x 60 mm Weight: 600g Power Supply: User replaceable 2 x alkaline D cell Battery pack. Battery Life: Up to five years (Based on one message a day i.e. 30 minute pulse count and no events enabled) Case Material: ABS & PC N.B Instrument operating range -20 o C to 60 o C in a non-condensing RH environment GPRS Quad band module Network Compatibility: Quad band, band user selectable (Quad Band) Aerial Connection: SMA socket Aerial Type: Stubby straight/right angle + optional remote mount on 2mtrs cable Product benefits GPRS technology Non-Intrusive design Easy installation A wide range of monitoring parameters available Individual configuration options Easy reading management system Comprehensive analysis and data history Up to five year battery life Instrumentation for Science and Industry ISI sa-nv Rue du Doyenné Brussels Tel +32 (0) Fax 02/ web : mail : sales@isi-be.com

8 isense communication to your local PC is easy using GPRS technology Typical applications Bridge stress and vibration monitoring Schools energy monitoring Hospitals and hospital food transportation monitoring Fridge temperature monitoring Civil engineering Laboratory monitoring Chemical transportation Application: Truck Temperature Application: Oil tank Pressure and level Application: Bridge Shock and vib ration Application: Hospital Fridges and freezer monitoring hanwell.com Application: School Energy monitoring GPRS IP Address secure access via DMZ (demilitarised zone) Server SR2 User PC Network Instrumentation for Science and Industry ISI sa-nv Rue du Doyenné Brussels Tel +32 (0) Fax 02/ web : mail : sales@isi-be.com

9 i S E N S E G P R S T R A N S M I T T E R Uncomplicated set-up capabilities Easy installation of software Clear set up capabilities Easily integrated into existing Hanwell monitoring system The screen shot opposite is an example of the set-up capabilities available to the user. Straightforward data retrieval Immediate access to graphical data Date and time specific Clear visual and statistical evidence of isense environmental conditions These screen shots show typical results for an isense transmitting data for temperature and humidity (above) and energy (right). Instrumentation for Science and Industry ISI sa-nv Rue du Doyenné Brussels Tel +32 (0) Fax 02/ web : mail : sales@isi-be.com

10 IS isense Basic Module The part numbers for the isense product range are constructed in four parts as follows: IS: C1 C2 C3 PS Where C1 = code for sensor on channel 1 C2 = code for sensor on channel 2 (00 = channel not used) C3 = code for sensor on channel 3 (00 = channel not used) PS = power supply option Currently available channel options include: Temperature Humidity Voltage Current Pulse Counting i S E N S E G P R S T R A N S M I T T E R Not all combinations are possible, please check with factory before ordering. For parameters not listed, please contact our sales team on +44 (0) or sales@hanwell.com. For further information and a full list of part numbers, visit Each isense unit requires a valid sim card contract and adequate network coverage at the intended location. Never compromising on craftsmanship, we have enhanced our products and services through design and manufacture, with all units being produced at our facility within the UK. We pride ourselves in our ability to accurately interpret customer requirements. If you require the monitoring of any substance or element not mentioned in this brochure, please call as we will, almost certainly, have a solution for you. Instrumentation for Science and Industry ISI sa-nv Rue du Doyenné Brussels Tel +32 (0) Fax 02/ web : mail : sales@isi-be.com

11 C O N T A C T Contact T: +32 (2) W: Instrumentation for Science and Industry Rue du Doyenné, Brussels Belgium Instrumentation for Science and Industry ISI sa-nv Rue du Doyenné Brussels Tel +32 (0) Fax 02/ web : mail : sales@isi-be.com