CURRENT TRANSFORMERS CATALOG
|
|
|
- Priscilla Haynes
- 6 years ago
- Views:
Transcription
1 URRENT TRANSFORMERS ATALOG split core solid core flex core TRENPOINT.OM
2 TABLE OF ONTENTS SPLIT ORE Model TN2/TN3/TN4 (TNx Series) 3 TNx Series Ordering Guide 4 Model TLF/ TBF (TxF Series) 5 TxF Series Ordering Guide 6 Model TSF 7 TSF Series Ordering Guide 8 Model TNF 9 TNF Series Ordering Guide 10 Model TMF 11 TMF Series Ordering Guide 12 SOLI ORE Model TTA 14 TTA Series Ordering Guide 15 Model TTB 16 TTB Series Ordering Guide 17 Model TT 18 TT Series Ordering Guide 19 Model TT 20 TT Series Ordering Guide 21 FLEX ORE Model TSR 23 TSR Series Ordering Guide 24
3 split core
4 Model TN2/TN3/TN4 (TNx Series) FEATURES Listed to UL 2808 and SA Revenue Grade Accuracy 75A to 600A Full Load Amps (FKA) 50/60Hz Measurement AT III / 600V Rated Low urrent Sensitivity Shrouded Split ore urrent Transformers Thick Plastic Hinged Snap Lid Top and Latch Nickel ore The TNx series current transformers are shrouded nickel core with snap, locking tilt top and classified as XOBA for direct installation under UL2808 and SA 22.2 No These are measurement category III current transformers for use in installations over insulated or bare conductors. The TNx series have been tested to 100 for use within Industrial control panels that meet the requirements of UL508. An internal burden resistor sets the full scale output voltage to 250mV and serves as an alternative to Ts that require shorting blocks to prevent open circuit shock. Type Specifications Input urrent A current, sine wave, 50 or 60 Hz urrent (Amps) 75, 100, 150, 200, 250, 300, 350, 400, 500, 600 Amps Voltage Rating 600VA rms, AT III per IE rest Factor Set to times full scale rated current Bandwidth 40Hz to 400Hz Output Voltage 250 mv Accuracy --- Temperature Range -40 o to 55 o Altitude Up to 2000 meters Pollution egree 2 Humidity Up to 95%, non-condensing onstruction Lead Wires Nickel-core, Molded case 120 o UL recognized plastic B/W twisted pair 18 AWG MTW UL1015, 600V, 105 o, double insulated TN2 =.40in [10.16mm] Window Opening TN3 =.70 [17.78mm] TN4 = 1.25in [31.75mm]
5 TNx Series Ordering Guide ATALOG NUMBER: _ A B E LETTER A B E ORRESPONING NUMBER Series Type urrent Rating (AMPS) Window Height Window Length Lead Length (FT.) A SERIES TYPE TN2 TN3 TN4 B urrent Rating (AMPS) 0020, 0075, , 0100, 0150, , 0100, 0150, 0200, 0300*, 0350, 0400, 0500, 0600 Width of Opening Height of Opening E Lead Length (FT) 012, , *, 012*, 030 *Normally Stocked Product Offering, (ustom sizes are available, requires longer lead times) EXAMPLE: _ T _ N _ 3 _ - 0 _ 1 _ 5 _ 0 _ - _ 0 0 _ 7 _ 0 _ - _ 0 0 _ 7 _ 0 _ - 0 _ 1 _ 2_ = Type TN3, 150 Amp rating, 0.70-inch window width, 0.70-inch window height, with a 12ft lead length
6 Model TFL / TBF (TxF Series) FEATURES Listed to UL 2808, AN/SA Accuracy ±0.5S% per IE Table 11 an be used on bare non-insulated conductors ategory III Field Installable Shrouded Split ore urrent Transformer Thick plastic hinged snap and tilt lid top and latch The Model TxF iron-core shrouded split current transformer is an indoor transducer designed for installation within breaker panels and industrial control cabinets. The snap and pull hinged top and latch simplifies installation over wires. TxF series Ts are UL Listed to UL2808 and SA AN for energy metering equipment, AT III. The T is provided with an internal resistor that produces a low voltage A designed output signal for 250mV at 100% of the rated current. omes with black and white twisted pair 600V (UL1015) output leads for VA output type and red and black for V output type. The Ts can be installed over either bare or insulated conductors. Type Specifications Input urrent A current, sine wave, 50 or 60 Hz urrent (Amps) 75, 100, 150, 200, 250, 300 Amps Voltage Rating 250VA rms (TLF); 600VA rms (TBF); AT III per UL2808 & SA rest Factor Set to times full scale rated current Bandwidth 40Hz to 400Hz Output Voltage 250 mv Accuracy --- Temperature Range -40 o to 55 o Altitude Up to 2000 meters Pollution egree 2 Humidity Up to 95%, non-condensing onstruction Lead Wires Window Opening Iron-core, Molded case 120 UL Listed, XOBA per E B/W twisted pair 18 AWG MTW UL1015, 600V, 105 o, double insulated TLF =.35in [8.89mm] TBF = 1.00 [25.4mm]
7 TxF Series Ordering Guide ATALOG NUMBER: _ A B E LETTER A B E ORRESPONING NUMBER Series Type urrent Rating (AMPS) Window Height Window Length Lead Length (FT.) A SERIES TYPE TLF TBF B urrent Rating (AMPS) 0075*, , 0100, 0150, 0200, 0250, 0300* Width of Opening Height of Opening E Lead Length (FT) 012*, *, 030* *Normally Stocked Product Offering, (ustom sizes are available, requires longer lead times) EXAMPLE: _ T _ N _ 3 _ - 0 _ 1 _ 5 _ 0 _ - _ 0 0 _ 7 _ 0 _ - _ 0 0 _ 7 _ 0 _ - 0 _ 1 _ 2_ = Type TN3, 150 Amp rating, 0.70-inch window width, 0.70-inch window height, with a 12ft lead length
8 Model TSF FEATURES Select any current from 400A up to 6000A 50/60Hz Listed to UL2808 and SA 22.2 No AT IV Revenue grade lass 0.5 Universal molds to any custom window size The TSF split current transformers are indoor type for Measurement ategory lass IV for use in energy monitoring and general electrical current sensing for field installations. The transformers have been designed to meet the requirements of UL2808 and SA 22.2 No They are provided with internal burden resistors to set the A output voltage. ustomer selects full load input current and with window size. The Model TSF can be used in both commercial and industrial applications. Type Specifications Input urrent A current, sine wave, 50 or 60 Hz urrent (Amps) Amps Voltage Rating 600VA rms; Tested AT IV per SA rest Factor Set to times full scale rated current Bandwidth 50Hz to 400Hz Output Voltage 250 mv Accuracy --- Temperature Range -40 o to 55 o Altitude Up to 2000 meters Pollution egree 2 Humidity Up to 95%, non-condensing onstruction Iron-core, UL approved per UL2808 AT IV to 120 Lead Wires B/W twisted pair 18 AWG MTW UL1015, 600V, 105 o, double insulated Window Opening ustom sizing from 1 x 1 to 12 x 12
9 TSF Series Ordering Guide ATALOG NUMBER: _ A B E LETTER A B ORRESPONING NUMBER Series Type urrent Rating (AMPS) Window Height Window Length EXAMPLE: _ T _ N _ 3 _ - 0 _ 1 _ 5 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 1 _ 2_ = Type TN3, 150 Amp rating, 0.70-inch window width, 0.70-inch window height, with a 12ft lead length E Lead Length (FT.) A SERIES TYPE TSF (SMALL) TSF (MEIUM) TSF (LARGE) B urrent Rating (AMPS) 0200, 0300, 0400, 0500, 0600, 0800, 01000, , 1800, 2000, , 4000, 4500, 5000, 6000 Width of Opening Height of Opening ustom Sizing ustom Sizing ustom Sizing ustom Sizing ustom Sizing ustom Sizing E Lead Length (FT) 012, , , 030 *Normally Stocked Product Offering, (ustom sizes are available, requires longer lead times)
10 Model TNF FEATURES Select any current from 400A up to 6000A 50/60Hz Listed to UL2808 and SA 22.2 No AT IV Revenue grade lass 0.5 Universal molds to any custom window size The TNF split current transformers are indoor type for Measurement ategory lass IV for use in energy monitoring and general electrical current sensing for field installations. The transformers have been designed to meet the requirements of UL2808 and SA 22.2 No They are provided with internal burden resistors to set the A output voltage. ustomer selects full load input current and with window size. The Model TNF can be used in both commercial and industrial applications. Type Specifications Input urrent A current, sine wave, 50 or 60 Hz urrent (Amps) Amps Voltage Rating 600VA rms; Tested AT IV per SA rest Factor Set to times full scale rated current Bandwidth 50Hz to 400Hz Output Voltage 250 mv Accuracy --- Temperature Range -40 o to 55 o Altitude Up to 2000 meters Pollution egree 2 Humidity Up to 95%, non-condensing onstruction Nickel-core, UL approved per UL2808 AT IV to 120 Lead Wires B/W twisted pair 18 AWG MTW UL1015, 600V, 105 o, double insulated Window Opening ustom sizing from 1 x 1 to 12 x 12
11 TNF Series Ordering Guide ATALOG NUMBER: _ A B E LETTER A B ORRESPONING NUMBER Series Type urrent Rating (AMPS) Window Height Window Length EXAMPLE: _ T _ N _ 3 _ - 0 _ 1 _ 5 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 1 _ 2_ = Type TN3, 150 Amp rating, 0.70-inch window width, 0.70-inch window height, with a 12ft lead length E Lead Length (FT.) A SERIES TYPE TNF (SMALL) TNF (MEIUM) TNF (LARGE) B urrent Rating (AMPS) 0200, 0300, 0400, 0500, 0600, 0800, 01000, , 1800, 2000, , 4000, 4500, 5000, 6000 Width of Opening Height of Opening ustom Sizing ustom Sizing ustom Sizing ustom Sizing ustom Sizing ustom Sizing E Lead Length (FT) 012, , , 030 *Normally Stocked Product Offering, (ustom sizes are available, requires longer lead times)
12 Model TMF FEATURES High sensitivity, linearity, and minimum phase shift Available in 75A, 50/60Hz Listed to UL2808 and SA 22.2 No AT IV Revenue grade lass 1 Accuracy Universal molds to any custom window size Ferrite core material The TMF miniature split-core current transformers feature a small physical size to accommodate tight-space applications and a mechanical hinge for multiple open/ close actions. The ferrite splitcore design permits easy non-contact installation and current measurements through magnetic field induction. Installation does not require the primary wire that is being measure be taken offline. The transformers have been designed to meet IE accuracy and UL2808 / SA 22.2 No safety requirements. An internal burden resistor sets the full-scale output voltage to 250mV and serves as an alternative to Ts that require shorting blocks to prevent open circuit shock protection for the installer. Type Specifications Input urrent A current, sine wave, 50 or 60 Hz urrent (Amps) 75 Amps Voltage Rating 720VA rms; AT IV per rest Factor Set to times full scale rated current Bandwidth 50Hz to 400Hz Output Voltage 250 mv Accuracy --- Temperature Range -15 to 60 Altitude Up to 2000 meters Pollution egree 2 Humidity Up to 95%, non-condensing onstruction Lead Wires Window Opening Ferrite core; Epoxy encapsulated; Nylon UL flame retardant rating 94V-0 case B/W twisted pair 18 AWG MTW UL1015, 600V, 105 o, double insulated.40in [10.16mm]
13 TMF Series Ordering Guide ATALOG NUMBER: _ A B E LETTER A B ORRESPONING NUMBER Series Type urrent Rating (AMPS) Window Height Window Length EXAMPLE: _ T _ N _ 3 _ - 0 _ 1 _ 5 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 1 _ 2_ = Type TN3, 150 Amp rating, 0.70-inch window width, 0.70-inch window height, with a 12ft lead length E Lead Length (FT.) A SERIES TYPE TMF B urrent Rating (AMPS) 0075* Width of Opening Height of Opening E Lead Length (FT) I04*, 002*, 012*, 030* *Normally Stocked Product Offering, (ustom sizes are available, requires longer lead times)
14 solid core
15 Model TTA FEATURES Rated Primary: 5A to 120A depending upon primary to secondary ratio selected. UL recognized, E compliant, RoHS compliant Revenue grade lass 0.1 Accuracy Nanocrystalline core The TTA Series is a toroidal (solid core) current transformers designed for applications where A current signals must be transformed into lower A current or voltage signals appropriate for microprocessor based circuits. The TTA series is designed specifically for integration into products which require exceptionally accurate signal transformation with low phase shift while exposed to harsh environmental operating conditions. Type Specifications Input urrent A current, sine wave, 50 or 60 Hz urrent (Amps) 20, 50, 100, 120 Amps Voltage Rating 720VA rms; AT IV per rest Factor Set to times full scale rated current Bandwidth 50Hz to 400Hz Output Voltage 250 mv at full scale rated current Accuracy --- Temperature Range -25 to 85 Altitude Up to 2000 meters Pollution egree 2 Humidity Up to 95%, non-condensing onstruction Nanocrystaline core; PBT Resin, UL flame retardant rating 94 V-0, Epoxy encapsulated Lead Wires B/W twisted pair 22 AWG AWM 1007, 300V, 80 Window Opening.50in [12.8mm]
16 TTA Series Ordering Guide ATALOG NUMBER: _ A B E WHITE 1.51 SOURE URRENT FLOW LOA BLAK FRONT VIEW TOP VIEW LETTER A B ORRESPONING NUMBER Series Type urrent Rating (AMPS) Window Height Window Length EXAMPLE: _ T _ N _ 3 _ - 0 _ 1 _ 5 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 1 _ 2_ = Type TN3, 150 Amp rating, 0.70-inch window width, 0.70-inch window height, with a 12ft lead length E Lead Length (FT.) A SERIES TYPE TTA B urrent Rating (AMPS) 0020*, 0050*, 0100*, 0120 Width of Opening Height of Opening E Lead Length (FT) 012*, 020, 030* *Normally Stocked Product Offering, (ustom sizes are available, requires longer lead times)
17 Model TTB FEATURES Rated Primary: 300A and 400A depending upon primary to secondary ratio selected. UL recognized, E compliant, RoHS compliant Revenue grade lass 0.1 Accuracy Nanocrystalline core The TTA Series is a toroidal (solid core) current transformers designed for applications where A current signals must be transformed into lower A current or voltage signals appropriate for micro processor based circuits. The TTA series is designed specifically for integration into products which require exceptionally accurate signal transformation with low phase shift while exposed to harsh environmental operating conditions. Type Specifications Input urrent A current, sine wave, 50 or 60 Hz urrent (Amps) 100, 200, 300, 400 Amps Voltage Rating 720VA rms; AT IV per rest Factor Set to times full scale rated current Bandwidth 50Hz to 400Hz Output Voltage 250 mv at full scale rated current Accuracy --- Temperature Range -25 to 55 Altitude Up to 2000 meters Pollution egree 2 Humidity Up to 95%, non-condensing onstruction Nanocrystaline core; PBT Resin, UL flame retardant rating 94 V-0, Epoxy encapsulated Lead Wires B/W twisted pair 22 AWG AWM 1007, 300V, 80 Window Opening 1.38in [35mm]
18 TTB Series Ordering Guide ATALOG NUMBER: _ A B E LETTER A B ORRESPONING NUMBER Series Type urrent Rating (AMPS) Window Height Window Length EXAMPLE: _ T _ N _ 3 _ - 0 _ 1 _ 5 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 1 _ 2_ = Type TN3, 150 Amp rating, 0.70-inch window width, 0.70-inch window height, with a 12ft lead length E Lead Length (FT.) A SERIES TYPE TTB B urrent Rating (AMPS) 0100, 0200, 0300, 0400 Width of Opening Height of Opening E Lead Length (FT) 012*, 030 *Normally Stocked Product Offering, (ustom sizes are available, requires longer lead times)
19 Model TT FEATURES Rated Primary: 600A and 800A depending upon primary to secondary ratio selected. UL recognized, E compliant, RoHS compliant Revenue grade lass 0.1 Accuracy Nanocrystalline core The TTA Series is a toroidal (solid core) current transformers designed for applications where A current signals must be transformed into lower A current or voltage signals appropriate for micro-processor based circuits. The TTA series is designed specifically for integration into products which require exceptionally accurate signal transformation with low phase shift while exposed to harsh environmental operating conditions. Type Specifications Input urrent A current, sine wave, 50 or 60 Hz urrent (Amps) 100, 200, 300, 400 Amps Voltage Rating 720VA rms; AT IV per rest Factor Set to times full scale rated current Bandwidth 50Hz to 400Hz Output Voltage 250 mv at full scale rated current Accuracy --- Temperature Range -25 to 55 Altitude Up to 2000 meters Pollution egree 2 Humidity Up to 95%, non-condensing onstruction Nanocrystaline core; PBT Resin, UL flame retardant rating 94 V-0, Epoxy encapsulated Lead Wires B/W twisted pair 22 AWG AWM 1007, 300V, 80 Window Opening 2.17in [55mm]
20 TT Series Ordering Guide ATALOG NUMBER: _ A B E LETTER A B ORRESPONING NUMBER Series Type urrent Rating (AMPS) Window Height Window Length EXAMPLE: _ T _ N _ 3 _ - 0 _ 1 _ 5 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 1 _ 2_ = Type TN3, 150 Amp rating, 0.70-inch window width, 0.70-inch window height, with a 12ft lead length E Lead Length (FT.) A SERIES TYPE TT B urrent Rating (AMPS) 0100, 0200, 0300, 0400, 0600, 0800 Width of Opening Height of Opening E Lead Length (FT) 012*, 030 *Normally Stocked Product Offering, (ustom sizes are available, requires longer lead times)
21 Model TT FEATURES Rated Primary: 5A to 120A depending upon primary to secondary ratio selected. UL recognized, E compliant, RoHS compliant Revenue grade lass 0.1 Accuracy Nanocrystalline core The TTA Series is a toroidal (solid core) current transformers designed for applications where A current signals must be transformed into lower A current or voltage signals appropriate for micro-processor based circuits. The TTA series is designed specifically for integration into products which require exceptionally accurate signal transformation with low phase shift while exposed to harsh environmental operating conditions. Type Specifications Input urrent A current, sine wave, 50 or 60 Hz urrent (Amps) 100, 200, 300, 400, 600, 800, 1000, 1200, 1500 Amps Voltage Rating 720VA rms; AT IV per rest Factor Set to times full scale rated current Bandwidth 50Hz to 400Hz Output Voltage 250 mv at full scale rated current Accuracy --- Temperature Range -25 to 55 Altitude Up to 2000 meters Pollution egree 2 Humidity Up to 95%, non-condensing onstruction Nanocrystaline core; PBT Resin, UL flame retardant rating 94 V-0, Epoxy encapsulated Lead Wires B/W twisted pair 22 AWG AWM 1007, 300V, 80 Window Opening 2.83in [71.9mm]
22 TT Series Ordering Guide ATALOG NUMBER: _ A B E LETTER A B ORRESPONING NUMBER Series Type urrent Rating (AMPS) Window Height Window Length EXAMPLE: _ T _ N _ 3 _ - 0 _ 1 _ 5 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 1 _ 2_ = Type TN3, 150 Amp rating, 0.70-inch window width, 0.70-inch window height, with a 12ft lead length E Lead Length (FT.) A SERIES TYPE TT B urrent Rating (AMPS) Width of Opening Height of Opening 0100, 0200, 0300, 0400, 0600, 0800, 1000, 1200, E Lead Length (FT) 012*, 030 *Normally Stocked Product Offering, (ustom sizes are available, requires longer lead times)
23 flex core
24 Model TSR FEATURES High sensitivity, linearity, and minimum phase shift Wide Range of urrent and Sensitivity Listed to UL2808 and SA 22.2 No AT IV Revenue grade lass 1 Accuracy Flexible ore Material Type Specifications Input urrent A current, sine wave, 50 or 60 Hz urrent (Amps) 1000A, 1200A, 1500A, 2000A, 3000A, 4000A Voltage Rating 600VA rms; AT IV rest Factor Set to times full scale rated current Bandwidth 1Hz to 100kHz Output Voltage 250 mv +/- 1% Accuracy --- Temperature Range -25 to 70 Altitude Up to 2000 meters Pollution egree 2 Humidity Up to 95%, non-condensing Lead Wires Window Opening (iameter) Input Power Source Power Source Lead Wires B/W twisted pair 18 AWG MTW UL1015, 600V, 105, double insulated 3.80in [96.52mm], 7.50in [190.5mm], 10.00in [254mm], 12.50in [317.5mm], 25.10in [637.54mm] +24 V R/W twisted pair 18 AWG MTW UL1015, 600V, 105, double insulated
25 TSR Series Ordering Guide ATALOG NUMBER: _ A B E LETTER A B ORRESPONING NUMBER Series Type urrent Rating (AMPS) Window Height Window Length EXAMPLE: _ T _ N _ 3 _ - 0 _ 1 _ 5 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 _ 0 7 _ 0 _ - _ 0 1 _ 2_ = Type TN3, 150 Amp rating, 0.70-inch window width, 0.70-inch window height, with a 12ft lead length E Lead Length (FT.) A SERIES TYPE TSR B urrent Rating (AMPS) 1000, 1200, 1500, 2000, 3000, 4000 Width of Opening Height of Opening 268, 530, 707, , 530, 707, 883 E Lead Length (FT) 30 *Normally Stocked Product Offering, (ustom sizes are available, requires longer lead times)
26 URRENT TRANSFORMERS ATALOG
CURRENT TRANSFORMERS CATALOG
URRENT TRANSFORMERS ATALOG split core solid core flex core TRENPOINT.OM TABLE OF ONTENTS SPLIT ORE Model TN2/TN3/TN4 (TNx Series) 4 TNx Series Ordering Guide 5 Model TLF/ TBF (TxF Series) 6 TxF Series
Current Transformers. Technical Data Sheet and Order Form
Current Transformers Technical Data Sheet and Order Form Model CTN2/CTN3/CTN4 (CTNx SERIES) FEATURES: Listed to UL 2808 and CSAC22.2 61010-1 Revenue Grade Accuracy 75A to 600A Full Load Amps (FLA) 50/60Hz
Powered by technology...driven by service CURRENT TRANSFORMERS. Multifunction Meters. Transducers & Isolators. Temperature Controllers
Multifunction Meters Transducers & Isolators Temperature Controllers Converters & Recorders Digital Panel Meters CURRENT TRANSFORMERS Current Transformers Analogue Panel Meters Shunts Digital Multimeters
TV31 Voltage/ Current Transformer
TV31 PCB Mounted Voltage/Current Transformers The Yuanxing TV31 voltage/ current transformer is designed for applications where the primary AC signal must be transformed accurately into a lower secondary
TRANSFORMERS CHASSIS TANSFORMERS FERRITE ROD 2328 LIGHTING TRANSFORMERS 2328 TOROIDAL TRANSFORMERS 2327 TRANSFORMERS
TRANSFORMERS PULSE TRANSFORMER DAVID USE PHOTO SD0010 AUDIO TRANSFORMER CHASSIS TRANSFORMER TOROIDAL TRANSFORMER LIGHTING TRANSFORMER DAVID USE PHOTO SD0010 CHASSIS TANSFORMERS 2325-2328 FERRITE ROD 2328
CPCO Series DC-AC Current Probe, Clamp On, 160mm, ±1000A ±2000A ±4000A ±8000A ±12000A, ±16000A
The CPCO Series (160mm aperture) Current Probes are Clamp On current sensors capable of measuring ac and dc currents. The Current Probe splits along a diameter allowing easy installation to existing cables
Efficient Energy Systems 3315ENG.
Efficient Energy Systems 3315ENG http://cleantechnica.com/2012/01/09/republican-fight-against-new-light-bulb-efficiency-regulations/ Topics Power and Energy Energy Auditing Efficient lighting Energy Harvesting
I PM. Current Transducer ITZ 5000-SB FLEX ULTRASTAB = 5000 A
urrent Transducer ITZ 5000-SB FLEX ULTRASTAB I PM = 5000 A For ultra-high precision measurement of current: D, A, pulsed..., with galvanic separation between primary and secondary. Separate magnetic head
Current / residual current and voltage transformers. Current / residual current and voltage transformers
Current / residual current and voltage transformers Current / residual current and voltage transformers 1 Overview Current transformer overview DIN rail current transformer with fuse Current transformer...
PRECISION CLAMP ON FLEXIBLE ROGOWSKI COIL CURRENT TRANSFORMER
JRF333M-X 333mVAC 24VDC, 2VA S1 S2 Vin + Vin - PRECISION CLAMP ON FLEXIBLE ROGOWSKI COIL CURRENT TRANSFORMER LED SINGLE PHASE output 333mV AC THREE PHASE output 333mV AC Power isast OPEN RCT is made with
Wide-band Models from DC to 100 MHz
CLAMP ON PROBE 327 series AC/DC CURRENT SENSOR CT686 series 99 Washington Street Melrose, MA 2176 Phone 781-665-14 Toll Free 1-8-517-8431 Visit us at www.testequipmentdepot.com Wide-band Models from DC
ENVIRONMENTAL. Operating Temperature: -40ºC to +125ºC. Insulator Color All Sizes 9 = UL White (Standard) 8 = UL Black (Special Order)
The market and applications for simple and reliable discrete Wire-to-Board connectors continue to evolve. AVX first introduced the 9176 series of surface mountable Displacement Connectors (IDC) in 2007.
Amveco Toroidal Solutions. Acme Electric s class leading toroidal magnetics is the perfect solution for the most challenging applications.
Amveco Toroidal Solutions Acme Electric s class leading toroidal magnetics is the perfect solution for the most challenging applications. AMVECO TOROIDAL SOLUTIONS Acme Electric s Amveco brand specializes
CPCO Series (160mm) DC-AC Current Probe, Clamp On ±4000A, ±8000A, ±12000A,
The CPCO Series (160mm) Current Probes are Clamp On current sensors capable of measuring ac and dc currents available in ranges of ±4000A ±8000A, ±12000A with an accuracy of +/-1% and non-linearity of
Voltage Adjustment. Load Regulation
HIGH DENSITY, CONFIGURABLE AC-DC POWER SUPPLY RCB1200 SERIES DS RCB1200 RE02 NOEMBER 2010 Description The RCB1200 is a modular, user configurable power supply offering unrivalled performances and flexibility.
2.2 American National Standards Institute Corporation and its applicable standards C39.1, C80.1, C89, C84.1.
TECHNICAL SPECIFICATIONS for Single Phase, 1 to 3 KVA Power Conditioner with Regulation and Distribution Constant Power 3 (CP3) CP36508A 7/15/04 1.0 General This specification covers the electrical characteristics
AC/DC current clamps (1/2) E N series
AC/DC current clamps The clamps use Hall-effect technology for the measurement of AC and DC currents from several milliamps to over 100 A. These clamps' narrow, elongated design makes them ideal areas
LFWLP W 12V 15.00A 25.00A 92%
WLP350 Series 350 Watts Low profile 1 5 x 3 footprint 200W / 350W Fan Up to 94% efficient Cover kits available EN55032 Level B conducted & radiated 5 Year warranty The LFWLP350 series of low profile, open
I P I OUT R L. Applications. Standards. N 52.D ; Page 1/8
Ref: ATO-10-B225-D10/SP3 r = 10 A ATO series is a split core current transformer for the electronic measurement of AC waveform current with galvanic separation between the primary circuit (power) and the
Product Specification sheet
INPUT MINIMUM RATED MAXIMUM Input Voltage 90V AC 100 240V AC 264V AC Input Frequency 47 Hz 50 / 60 Hz 63 Hz Input Current * 350mA Inrush Current **
Standard AWG: WTB
The 917X series of surface mount Insulation Displacement Connectors (IDC) were developed to meet the harsh automotive and industrial market applications for connecting individual wires directly to a PCB
EMI Cores ESD-R-B Toroidal Cores for Round Cables for Low & High Frequency (with snail-shaped case) Applications
EMI Cores ESD-R-B Toroidal Cores for Round Cables for Low & High Frequency (with snail-shaped case) Overview The KEMET ESD-R-B series solid toroidal cores are designed to use on round cables. The wide
World-Class Accuracy & Measurement Range (40 Conventional Models)
AC/DC CURRENT SENSOR CT6904 Ultra-High Performance AC/DC Current Sensor World-Class Accuracy & Measurement Range (40 Conventional Models) 500 A (rms) Rated for measurement of large currents 4 MHz (±3 db)
Amphenol. Advantage. R-Line R-146. Rectangular Attached Multi-Pin Industrial Cable Assemblies. Amphenol - Sine Systems
Amphenol Rectangular Attached Multi-Pin Industrial Assemblies Advantage R-146 R-Line Amphenol - Sine Systems Advantage * vs. the R-Line Molded Advantage Series * Patents pending Low Cost UL & CSA Listed
ENVIRONMENTAL. Operating Temperature: -40ºC to +125ºC. Insulator Color 9 = UL White 8 = UL Black Special Order Ø Ø Ø
The market and applications for simple and reliable discrete Wire-to-Board connectors continue to evolve. AVX first introduced the 9176 series of surface mountable Displacement Connectors (IDC) in 2007.
RI-D440. Three Phase easywire Multifunction DIN Rail Energy Meter. Telephone : +44 (0) Displayed Parameters
RI-D440 Three Phase easywire Multifunction DIN Rail Energy Meter Four module DIN rail mounted Energy pulse LED 330mV Input from easywire CTs (or -/1A and -/5A current transformer input with TAS-SCTEWA
SEALED, ILLUMINATED ROCKER SWITCHES
K/K LOW OST, ROKER FOR WET & DUSTY ENVIRONMENTS The K series rockers are rugged, high performance sealed switches designed for use under severe conditions found in marine, appliance, heavy equipment and
ENVIRONMENTAL. Operating Temperature: -40ºC to +125ºC. Insulator Color 9 = UL White 8 = UL Black Special Order
The market and applications for simple and reliable discrete Wire-to-Board connectors continue to evolve. AVX first introduced the 9175 series of surface mountable Insulation Displacement Connectors (IDC)
ENVIRONMENTAL. Operating Temperature: -40ºC to +125ºC 0XX. Wire Gauge Size. Code Accepted Wire Cap Code Wire Gauge Insulation Pages 6-7
The 917X series of surface mount Displacement Connectors (IDC) were developed to meet the harsh automotive and industrial market applications for connecting individual wires directly to a PCB ranging from
Tap Changer Analyzer & Winding Ohmmeter RMO25TD
Tap Changer Analyzer & Winding Ohmmeter RMO25TD Test current 5 ma 25 A DC Rapid automatic demagnetization AC Current monitoring channel Lightweight 9,5 kg Measuring range 0,1-2 k Two voltage sense channels
Over or Under Current. Over and Under Current Monitor. Current Transducer. Current Indicator. DIN Rail Mounting Current Monitors
Selection Guide...8.2 Over or Under ECS... 8.4 TCS... 8.8 Over and Under Monitor ECSW... 8.6 Transducer TCSA... 8.10 DCSA... 8.12 Indicator LCS... 8.14 LPM... 8.14 DIN Rail Mounting CM-SFS CM-SRS.1 CM-SRS.2
LDW25-24 is a single or two phase AC or DC input DIN Rail Switching Power Supply.
LDW25-24 is a single or two phase AC or DC input DIN Rail Switching Power Supply. Its compact size, high efficiency, excellent reliability together with easy installation due to pluggable connectors makes
Mitered Mortise & Tenon - Raised Panel
abinet Door & Drawer Front Options Mitered Mortise & Tenon - Raised Panel Style: 10M P: 301 Frame: P301 x 0.6 Min. Size: 8x8 [03.mm x 03.mm] Style: 10M* Drawer Front P: 301 Frame: P301 x 0.6 Min. Size:
LIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING
LIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING 1.0 General This specification covers the electrical characteristics and general
EMI Cores ESD-R-H Toroidal Cores for Round Cables for Low & High Frequency & High Heat Resistance (with case) Applications
EMI Cores ESD-R-H Toroidal Cores for Round Cables for Low & High Frequency & High Heat Resistance (with case) Overview The KEMET ESD-R-H Series solid toroidal cores feature high heat resistance for round
HC2F100-SN CLIPS AUTOMOTIVE CURRENT TRANSDUCER HC2F100-SN CLIPS. Datasheet
AUTOMOTIVE CURRENT TRANSDUCER Datasheet 071113/1 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. Page 1/ 6 www.lem.com Introduction
AC FLEXIBLE CURRENT PROBE CA 3000
AN ISO 9001:2008 COMPANY AC FLEXIBLE CURRENT PROBE CA 3000 Symbol Definition & Button Location Name of Parts & Position: 2 1 Flexible current probe 2 Probe coupling 3 Power on / Range switch 4 Banana plugs
Application Description
- N Mechanically Held February ontents Description Page Product Description...... - Application Description... - Features................ - Operation.............. - Instructional Leaflets..... - Standards
Power Supplies 3. SDN-C Compact DIN Rail Series
SDN-C Compact DIN Rail Series The SDN-C DIN rail power supplies are the next generation of the popular SDN series. These models combine high efficiency and compact size with new visual diagnostic LEDs
Suitable for lighting and motor load, 1 Form A 50A latching relays
Suitable for lighting and motor load, 50A latching relays DJ-H RELAYS (ADJH) 9.0 5 1 0.2 9.0 5 New 1 FEATURES 1. High inrush capability Tungsten load (TV-20 class) Electronic ballast load (NEMA10) Capacitive
DOBLE F6150e TECHNICAL SPECIFICATIONS
DOBLE F6150e TECHNICAL SPECIFICATIONS The F6150e line of System Simulators is designed for simulation tests on relay and protection schemes. There are four distinct models for your specific testing needs.
Input Modules for TESLA Power System Recorders
Input Modules for TESLA Power System Recorders Modules Described In This Document DC Isolation Input Module - Model 401016 Input (ac or dc signals) AC Current Module - 5 A, new model 110739, old model
Industrial Serie +600S
D A T A S H E E T Industrial Serie +6S Modular Configurable Reduced fan noise Enhanced Line Derating 6 watts in the palm of your hand The +6S series fetures improved low input line derating delivers 6
User s Manual Current Probe. IM E 1st Edition. Yokogawa Electric Corporation
User s Manual 701932 Current Probe Yokogawa Electric Corporation 1st Edition Foreword Revisions Thank you for purchasing the 701932 Current Probe. This user's manual contains useful information about the
1.7 mm pitch, Low Profile Board to Wire Connectors for Power Supplies
NEW 1.7 mm pitch, Low Profile Board to Wire Connectors for Power Supplies DF65 Series (UL Pending) Lock structure and operation Socket Header Latch Latches are deflected slightly during mating. Features
INTELLIMETER REGISTER
INTELLIMETER REGISTER MODEL RG2 INSTALLATION AND CONNECTIONS INSTALLATION MANUAL WARNING: Any work on or near energized metering equipment can present a danger of electrical shock. All work on these products
NK Technologies Ground Fault Sensor. Instrument Transformer AC Current Transducers NEW SPECIFICATIONS
Instrument Transformer urrent Transducers Large Window rea 4-20m The PL is a 4 terminal device with separate connections for power and load. The PM is a two terminal device. 24V is applied between the
Installation Manual DOC R1 Date: 05/27/99. Plug-in Meter Installation Manual
Installation Manual DOC-4004-5015-R1 Date: 05/27/99 Plug-in Meter Installation Manual Document Number: Doc-4004-5015-R1 Document Release Date: 5/99 Copyright 1999 TeCom Inc. All rights reserved. No part
Power supply CP-E 24/2.5
2CDC 271 015 F0t06 a OUTPUT L+, L : terminals output b DC OK: terminal signalling output c INPUT L, N, PE: terminals input d OUTPUT OK: green LED output voltage OK e OUTPUT Adjust: potentiometer adjustment
SERIE E N. The E N series clamps use Hall-effect technology for the measurement of AC and DC currents from several milliamps to over 100 A.
Pinces Current ampèremetriques clamps for AC/DC pour current courant AC SERIE E N The E N series clamps use Hall-effect technology for the measurement of AC and DC currents from several milliamps to over
DOBLE F6150SV TECHNICAL SPECIFICATIONS
DOBLE F6150SV TECHNICAL SPECIFICATIONS The F6150sv line of System Simulators is designed for simulation tests on relay and protection schemes. There are four distinct models for your specific testing needs.
JIANGYIN SPARK ELECTRONIC TECHNOLOGY CO.,LTD
Split Core (Clip on) Current Sensor The JIANGYIN SPARK series of split core current sensors are designed for fast and easy installation. Split-core transformers are ideal for installation on existing electrical
Power Processor - Series 700F 10KVA to 150KVA
Power Processor - Series 700F 10KVA to 150KVA Power Conditioning and Regulation for Commercial & Industrial Equipment General Specifications PART 1 - GENERAL 1.1 DESCRIPTION This specification defines
ENVIRONMENTAL. Operating Temperature: -40ºC to +130ºC. Wire Size. Code Accepted Max Wire Gauge Insulation AWG Solid or Stranded
Wire-to-Wire (WTW) connectors have been used in the industrial market for years with traditional 2-Piece (plug & socket) connector systems. These require crimp and poke wire terminations to connect discrete
Current clamps for AC current
Current clamps for AC current "C100" series The "C100" series is a range of thirteen transformer clamps with all the advantages of our old "C30" series clamps whilst incorporating considerable improvements,
MODEL: M2VF MODEL: M2VF [1][2] [3][4]
![MODEL: M2VF MODEL: M2VF [1][2] [3][4]](/thumbs/79/79182356.jpg "MODEL: M2VF MODEL: M2VF [1][2] [3][4]")
Super-mini Signal Conditioners Mini-M Series SIGNAL TRANSMITTER (high speed response) Functions & Features Converts DC input from a sensor into a standard process signal Isolation between input and output
Electromechanical Printed Circuit Board Relays Application Data
Electromechanical Printed Circuit Board Relays Application Data Introduction: In the past several years the dry reed relay has become an important product among relay specifiers, primarily because of the
PQube 3 Specifications
PQube 3 Specifications Reference conditions for factory tests: 19~25 C, 10%~70% RH MAINS VOLTAGE MEASURING CHANNELS Measurement Channels Power Configuration/ Range of Nominal Input Voltage 3 Line to Neutral,
HPS Universal BUCK-BOOST TRANSFORMERS
BUCK-BOOST TRANSFORMERS Single and Three Phase Potted Buck-Boost Transformers Buck-Boost Applications & Standard Specification... 80 Selecting Buck-Boost Transformers... 81 Single Phase Selection Tables...
USB 2.0-IP67 Water Resistant Connector System
Section 6 USB 2.0-IP67 Water Resistant Connector System CONEC completed its product line of bayonet locking series, IP67 rated industrial USB 2.0 connector system for harsh environments. The housing can
General Specifications
General Specifications GS 77M00-0EN Models R-S, R-H, R-T, R-RT, R-LP, R-HP, R-SP, R-SY, R-PS, R-PH, R-PW, R-, R-D6 rrester [Style: S] General This high quality arrester protects electronic instruments
Safety Warnings Features Specifications Instrument Layout Operation Preparation AC Current Measurement How to Use Peak Hold Function How to Use The
Safety Warnings Features Specifications Instrument Layout Operation Preparation AC Current Measurement How to Use Peak Hold Function How to Use The Frequency Selector Switch How to Use Data Hold Function
Current clamps for AC current
Current clamps for AC current Small, compact and particularly resistant, this range of miniature clamps is designed for measurements from a few milli-amperes to 150 A AC. Their shape makes them very practical
SPECIFICATIONS FOR THE NI PXI/PCI-4060
SPECIFICATIONS FOR THE NI PXI/PCI-4060 This document lists the specifications of the NI PXI/PCI-4060. These specifications are guaranteed between 15 and 35 C unless otherwise specified. DC Voltage (% of
Specifications. Specifications and Characteristics Specifications
Specifications and Specifications Specifications All specifications are warranted. Specifications are valid after a 30-minute warm-up period and ±5 C from last calibration temperature. Bandwidth (-3dB)
Protection components
Multifunction protection relays LT-P Environment Conforming to standards IEC 947-4-1, IEC 34-11, IEC 755, VDE 010, VDE 00. &Ãmarking Meets the essential requirements of the Low Voltage equipment (LV) &
CURRENT TRANSFORMERS FOR ELECTRONIC WATTHOUR METERS ADVANCED MATERIALS THE KEY TO PROGRESS
CURRENT TRANSFORMERS FOR ELECTRONIC WATTHOUR METERS ADVANCED MATERIALS THE KEY TO PROGRESS CURRENT TRANSFORMERS FOR ELECTRONIC WATTHOUR METERS VACUUMSCHMELZE GmbH & Co. KG (VAC) is one of the worldwide
Metallized Polyester Film Capacitors MKT Radial Potted Type
MKT 372 168x12(halfpage) l w FEATURES Available taped and loose in box h lt Lead (Pb)-free product RoHS-compliant product APAITANE TOLERANE ± 10 %; ± 5 % e3 RoHS OMPLIANT P Dimensions in mm Ødt RATED (D)
Data Sheet. Hall effect transducers, current and voltage
Data Pack E Issued March 200 232-20 Data Sheet Hall effect transducers, current and voltage This data sheet covers the following products: RS stock no. Type of transducer 28-3 Multi-range current, PCB
10.00 (1/2) PAC series
Clamp-on AC/DC current probes PAC Series The is a range of professional AC/DC clamp-on current probes designed to meet the very latest in safety and performance standards. There are two different jaw designs
Review 6. unlike poles cause the magnets to attract. like poles cause the magnets to repel.
Review 6 1. The two characteristics of all magnets are: they attract and hold Iron, and, if free to move, they will assume roughly a south - north position. 2. Lines of flux always leave the north pole
IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL:
IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: 61-352 The Service Information provides the following information: Precautions and safety information Specifications Basic maintenance (cleaning, replacing
PRELIMINARY DATA SHEET RI-D140. Three Phase Multifunction DIN Rail Energy Meter (MID Certified) MID
RI-D140 Three Phase Multifunction DIN Rail Energy Meter (MID Certified) Four module DIN rail mounted Energy pulse LED True RMS measurement Cost effective and accurate Modbus communication -/1A or -/5A
DUAL OUTPUT AC CURRENT/VOLTAGE TRANSDUCER
OPERATOR S MANUAL DUAL OUTPUT AC CURRENT/VOLTAGE TRANSDUCER Masibus Automation & Instrumentation Pvt. Ltd. B/30, GIDC Electronics Estate, Sector-25, Gandhinagar-382044, Gujarat, India Web Site: www..com
Asia-Pacific North America Europe, Middle East Bel Power Solutions, Inc. BCD.
The MPU200/MDU200 Series is based upon the proven architecture of the MPU150/MDU150 product line. The MPU products incorporate Power Factor Correction (PFC) with a low-profile package designed to meet
ET-3888 True RMS Clamp Meter. User Manual
ET-3888 True RMS Clamp Meter User Manual Index Introduction... 3 Safety Notes... 4 Features... 5 Specifications... 6-8 Instrument Layout... 9 Measurement... 10 Maintenance... 11 Page 2 1. Introduction
Agilent 1146A AC/DC Oscilloscope Current Probe
A User s Guide Publication number 01146-92003 May 2005 Copyright Agilent Technologies 1996-2005 All Rights Reserved Contents Receiving Your Shipment -2 Packaging -2 Description -3 Compatibility -3 Control
MM V 10A ENGLISH. INSTRUCTION MANUAL Auto-Ranging DATA HOLD AUDIBLE CONTINUITY MIN / MAX TEMPERATURE DIODE TEST CAPACITANCE
INSTRUCTION MANUAL Auto-Ranging Digital Multimeter MM400 DATA HOLD AUDIBLE CONTINUITY MIN / MAX TEMPERATURE DIODE TEST CAPACITANCE 600V 10A 40MΩ 2 GENERAL SPECIFICATIONS Klein Tools MM400 is an auto-ranging
Product Data Sheet 3252J/2H3PU
3252J/2H3PU INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating Data... 7 3.3
2.1 Performance Standards The UPS is designed with the applicable sections of UL, CUL, and ISO The UPS has UL and CUL listing.
1.0 Scope This document describes the specification for Toshiba 1000 Series On-Line Uninterruptible Power System (UPS). The UPS will supply a computer grade AC output sine wave which is unaffected by the
1.7mm pitch, Low Profile Wire-to-Board Connectors for Power Supplies
1.7mm pitch, Low Profile Wire-to-oard onnectors for Power Supplies DF Series (UL, -UL, Listed) Lock structure and operation Socket Latch Header Latches are deflected slightly during mating. Features 1.
Power supply CP-T 48/20.0 Primary switch mode power supply
Data sheet Power supply CP-T 48/20.0 Primary switch mode power supply The CP-T range of three-phase power supply units is the youngest member of ABB s power supply family. In terms of design and functionality,
Overview. Applications. Benefits. EMI Cores ESD-SR Snap-on Cores for Round Cables for Low & High Frequency (with case)
EMI Cores ESD-SR Snap-on Cores for Round Cables for Low & High Frequency (with case) Overview The KEMET ESD-SR Series snap-on toroidal cores are designed for use on round cables. The wide range of Manganese
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer ITL 4000-S I PN = 4000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. I > 0 P Features Closed
ZBRRA Programmable receiver - 2 relays V AC/ DC - 2 pusbuttons - 6 LEDs
Characteristics Programmable receiver - 2 relays - 24..240 V AC/ DC - 2 pusbuttons - 6 LEDs Product availability : Stock - Normally stocked in distribution facility Price* : 410.00 USD Main Range of product
CL900. True RMS 1000V 2000A 60MΩ ENGLISH. INSTRUCTION MANUAL 2000A Digital Clamp Meter. Measurement Technology
ENGLISH INSTRUCTION MANUAL 2000A Digital Clamp Meter True RMS Measurement Technology NON-CONTACT VOLTAGE TESTING INRUSH CURRENT LOW IMPEDANCE DATA HOLD RANGE HOLD AUDIBLE CONTINUITY DIODE TEST CAPACITANCE
374/375/376 Clamp Meter. Users Manual
374/375/376 Clamp Meter Users Manual Introduction XWWarning Read "Safety Information" before you use the Meter. The Fluke 374, 375, and 376 (the Meter) measure true-rms ac current and voltage, dc current
Advanced Test Equipment Rentals ATEC (2832) CIBANO in-1 test system for medium- and high-voltage circuit breakers
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) CIBANO 500 3-in-1 test system for medium- and high-voltage circuit breakers Medium- and high-voltage circuit breaker
EA16, EB16, EA17, EA19, EA12 MOVING-IRON METERS Ammeters and Voltmeters
EA16, EB16, EA17, EA19, EA12 MOVING-IRON METERS Ammeters and Voltmeters EA12 EA19 EA17 EA16 EB16 APPLICATION EA16, EB16, EA17, EA19 and EA12 moving-iron meters are intended for measuring AC voltage or
Clip-on RF Current Meter
1. Introduction 3. Clip-on RF Current Meter The most useful tool for RF interference troubleshooting! Also in Japanese G0SNO's original article was in RadCom (RSGB) April 1993, page 74. The original Maplin
The MDU150 Series provides the same benefits as the MPU150 Series, with nominal 48 volt DC input.
The innovative MPU products incorporate Power Factor Correction (PFC) with a low-profile package designed to meet 1U height constraints. The MPU150-4530G and MPU150-4350G provide high current +3.3 V and
Jewell DPM Power / Power Factor Size 96/96 BEST IN CLASS
Application: The Jewell DPM Power 96x96 series measures system active Power (Import/Export), Reactive Power (Import/Export), Apparent Power & Power Factor of Three Phase and Single Phase Network. It has
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. FEATURES AND SPEIFIATIONS Features and Benefits Board-mounting pegs provide
Relays & Sockets RU Series Universal Relays. With Latching or Momentary Lever. Standard (without lever) Key features:
RU Series Universal Relays Key features: Full featured universal miniature relays Designed with environment taken into consideration Two terminal styles: plug-in and PCB mount Non-polarized LED indicator
Flexible AC current probes
Flexible AC current probes Making use of the principle of Rogowski coils, the MiniFLEX models are flexible sensors offering a wide dynamic range for measuring AC intensities and viewing high-speed current
MEDER electronic. DIL Series DESCRIPTION FEATURES CHARACTERISTICS. DIMENSIONS All dimensions in mm [inch] ORDER INFORMATION
![MEDER electronic. DIL Series DESCRIPTION FEATURES CHARACTERISTICS. DIMENSIONS All dimensions in mm [inch] ORDER INFORMATION](/thumbs/72/67828129.jpg "MEDER electronic. DIL Series DESCRIPTION FEATURES CHARACTERISTICS. DIMENSIONS All dimensions in mm [inch] ORDER INFORMATION")
kvd Breakdown Option DESRIPTION Several pin out options are possible with the 14 pin DIL series. Suitable for telecommunication applications where breakdown voltages up to 4.25 kvd is required. FEATURES
Metallized Polyester Film Capacitors MKT Radial Potted Type
MKT 372 168x12(halfpage) l w FEATURES Available taped and loose in box h lt Lead (Pb)-free product RoHS-compliant product APAITANE TOLERANE ± 10 %; ± 5 % e3 RoHS OMPLIANT P Dimensions in mm Ødt RATED (D)
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer CAS 25-NP/SP2 N = 25 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Closed loop (compensated)
PRODUCT SPECIFICATION FOR A 15 AND 75 kva, THREE PHASE MODULAR POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING (Varian)
PRODUCT SPECIFICATION FOR A 15 AND 75 kva, THREE PHASE MODULAR POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING (Varian) 1.0 General This specification covers the electrical characteristics and
ProLine P Precise Temperature Measurement at High Voltage Potentials up to 6.6 kv
Precise Temperature Measurement at High Voltage Potentials up to 6.6 kv When temperatures are to be measured using Pt100 resistance thermometers in high-voltage environments, standard temperature transmitters