Technical Description. Wireless Proximity Switches Antenna WAT100

Transcription

1 Technical Description Wireless Proximity Switches Antenna

2 Please note the following Target group This description is intended for the use of trained specialists in electrical installation and control and automation engineering, who are familiar with the applicable national standards. Safety requirements The responsible staff must ensure that the application or use of the products described satisfy all the requirements for safety, including all the relevant laws, regulations, guidelines and standards. Liability The documentation has been prepared with care. The products described are, however, constantly under development. For that reason the documentation is not in every case checked for consistency with performance data, standards or other characteristics, and does not represent an assurance of characteristics in the sense of 459, Para. 2 of the German Civil Code. In the event that it contains technical or editorial errors, we retain the right to make alterations at any time and without warning. No claims for the modification of products that have already been supplied may be made on the basis of the data, diagrams and descriptions in this documentation. This manual is copyrighted. Any reproduction or third party use of this protected publication, whether in whole or in part, without the written permission of ABB Automation Products GmbH, is forbidden

3 : Antenna and accessories for input module WDI100 Fig. 1: Antenna and antenna cable WAC100 Content : Antenna and accessories for input module WDI Purpose and short description...4 Technical data...4 Ordering data...5 Installation instructions

4 Purpose and short description The antenna transmits and receives the signals exchanged between the input module and the wireless proximity switches. For each input module, two antennas with different polarization (-R and -L) are connected. The connection is made by one antenna cable each (WAC100-N03 or WAC100-N05). Longer or series connected cables lead to a loss of range For the wall and mast assembly of the antenna there is the antenna support (WAM100-N), which permits a swivelling of the antenna for accurate adjustment also after the assembly. Technical data -R, -L Frequency range Polarization Gain -R -L 3 db beamwidth, horizontal 70 3 db beamwidth, vertical GHz circular left polarized circular right polarized 8.5 dbi Max. power 75 W (CW) at 25 C Impedance 50 Ω Operating temperature -40 C C Storage temperature -40 C C Degree of protection according to IEC Housing material Antenna back Antenna body Dimensions (width x height x depth) Weight Connection WAC100-N03, WAC100-N05 IP54 ASA and aluminium, colour: RAL 7042 (dark-gray) ASA, colour: RAL 7035 (light-gray) 101 mm x 95 mm x 32 mm 100 g SMA female Cable construction Material Diameter Inner conductor CuAg 1.00 mm Dielectric SPEX 3.00 mm 1. outer conductor CuAg network 3.60 mm 2. outer conductor CuAg network 4.15 mm cable sheath RADOX 125, 4.95 mm colour: RAL 9005 (black) Impedance 50 Ω +/-2 Ω Capacity 95.0 pf/m Signal delay 4.75 ns/m Min. shielding > 81 db (up to 3 GHz) Isolation resistance > 10,000 MΩ/m Material aluminium, steel Operating temperature -40 C C Storage temperature -40 C C - 4 -

5 WAC100-N03, WAC100-N05 (continuation) Min. bending radius static: 20 mm; repeated bending: 40 mm Halogen-free Yes, according to IEC Flame protection according to IEC ; UL Length WAC100-N03 3 m WAC100-N05 5 m Weight WAC100-N g WAC100-N g Connection SMA male both sides WAM100-N Weight 95 g Material aluminium, steel Ordering data Type Designation Ordering number EAN number -R Antenna for input module, 1SAF900600R right-handed circular polarization -L Antenna for input module, 1SAF900600R left-handed circular polarization Accessories WAC100-N03 Antenna cable, 3 m, 1SAF900600R male SMA connection on both sides WAC100-N05 Antenna cable, 5m, 1SAF900600R male SMA connection on both sides WAM100-N Antenna holder for wall and mast mounting 1SFA900900R

6 Installation instructions WARNING! Be careful when working at height! Always secure ladders! Always tighten screws! Never close the drainage holes! - 6 -

7 - 7 -

8 Contact us ABB Automation Products GmbH Wallstadter Str Ladenburg, Germany Phone: Fax : plc.sales@de.abb.com Note: We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB AG does not accept any responsibility whatsoever for potential errors or possible lack of information in this document. We reserve all rights in this document and in the subject matter and illustrations contained therein. Any reproduction, disclosure to third parties or utilization of its contents in whole or in parts is forbidden without prior written consent of ABB AG. Copyright 2012 ABB All rights reserved 3ADR071004D