8-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT

Size: px

Start display at page:

Download "8-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT"

Bruce Woods
6 years ago
Views:

Frequency Range Dual Polarization HPB Adjust. Electr. DT R1 790 960 B1 1710 1880 B2 1920 2170 Y1 2490 2690 X X X X 65 65 65 65 0.5 9.

1 Frequency Range Dual Polarization HPB Adjust. Electr. DT R B B Y X X X X set by hand or by optional RCU (Remote Control Unit) 8-Port Antenna / / / /65 /65 /65 17/17.5/18/18dBi /2 8 /2 8 /2 8 T Type No V01 Lowband R1, connector Frequency Range MHz Gain at mid Tilt dbi Gain over all Tilts dbi 16.8 ± ± ± 0.4 Horizontal Pattern: Azimuth Beamwidth 68 ± ± ± 1.2 Front-to-Back Ratio, Total Power, ± 30 db > 22 > 24 > 24 Cross Polar Discrimination over Sector db > 9.5 > 10.0 > 11.0 Azimuth Beam Squint 0.0 ± ± ± 1.5 Vertical Pattern: Elevation Beamwidth 7.6 ± ± ± 0.3 Electrical Downtilt continuously adjustable Tilt Accuracy < 0.3 < 0.3 < 0.4 First Upper Side Lobe Suppression db > 17 > 18 > 18 Cross Polar Isolation db > 30 Port to Port Isolation db > 35 (R1 // B1, B2, Y1) per Port 400 (at 50 C ambient temperature) Port (at 50 C ambient temperature) Values based on NGMN-P-BASTA (version 9.6) requirements V01 Page 1 of 4

2 Highbands B1, connector 3 4 B2, connector 5 6 Y1, connector Frequency Range MHz Gain at mid Tilt dbi Gain over all Tilts dbi 17.7 ± ± ± 0.3 Horizontal Pattern: Azimuth Beamwidth 62 ± ± ± 3.0 Front-to-Back Ratio, Total Power, ± 30 db > 24 > 26 > 23 Cross Polar Discrimination over Sector db > 8.0 > 11.0 > 10.5 Azimuth Beam Squint 0.5 ± ± ± 1.2 Vertical Pattern: Elevation Beamwidth 4.9 ± ± ± 0.2 Electrical Downtilt continuously adjustable Tilt Accuracy < 0.2 < 0.2 < 0.1 First Upper Side Lobe Suppression db > 18 > 17 > 20 Cross Polar Isolation db > 28 Port to Port Isolation > 30 (B1 // B2, Y1) db > 30 (B2 //B1, Y2) > 30 (Y1 // B1, B2) > 35 (B1, B2, Y1 // R1) per Port 150 (at 50 C ambient temperature) Port (at 50 C ambient temperature) Values based on NGMN-P-BASTA (version 9.6) requirements. Page 2 of V01

3 Electrical specifications, all systems Impedance Ω 50 VSR < 1.5 Return Loss db > 14 Interband Isolation db > 30 Passive Intermodulation dbc < 150 (2 x 43 dbm carrier) Polarization +45, (at 50 C ambient for the Antenna temperature) Values based on NGMN-P-BASTA (version 9.6) requirements. Mechanical specifications Input Connector Position Adjustment Mechanism 8 x 7-16 female long neck bottom 4x, Position bottom continuously adjustable ind load (at Rated N lbf Frontal: ind Speed: 150 km/h) Maximal: Max. ind Velocity Height / idth / Depth Category of Mounting Hardware eight Packing Size Scope of Supply km/h mph mm inches kg lb mm inches / 300 / / 11.8 / 6.0 H (Heavy) 34.0 / 36.2 (clamps incl.) 74.9 / 79.7 (clamps incl.) 2951 / 322 / / 12.7 / 7.5 Panel and 2 units of clamps for mm inches diameter Accessories (order separately if required) 1) 2) 1) ) Type No. Description Remarks mm inches eight approx. kg lb Units per antenna clamp Mast diameter: clamp Mast diameter: downtilt kit Downtilt angle: Accessories (included in the scope of supply) clamp Mast diameter: For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit. all mounting: No additional mounting kit needed. Material: Grounding: Reflector screen: Aluminum. Fiberglass housing: It covers totally the internal antenna components. The special design reduces the sealing areas to a minimum and guarantees the best weather protection. Fiberglass material guarantees optimum performance with regards to stability, stiffness, UV resistance and painting. The color of the radome is light grey. All nuts and bolts: Stainless steel or hot-dip galvanized steel. The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. Adjustment mechanism with integrated scale All dimensions in mm inches V01 Page 3 of 4

4 Layout of interface: * Tilt Tilt Tilt Tilt * * Bottom view * Dimensions refer to radome All dimensions in mm inches Correlation Table Frequency range Array Connector MHz R MHz B MHz B MHz Y x 1x Y1 B2 B1 R1 Any previous data sheet issues have now become invalid. Page 4 of V01

5 Mounting Hardware Clamp Included in the Scope of Supply Suitable for mast diameter Antenna mast distance Material of clamp and screws eight (mm) [inches] (mm) [inches] (kg) [lb] [ ] [ ] Hot-dip galvanized steel / stainless steel 1.1 [2.43] 152 [5.98] 100 [3.94] 72 [2.83] [ ] 40 [1.57] 35 [1.38] 64 [2.52] 125 [4.92] /c Subject to alteration. 40 [1.57] [ ] M10 M A = 25 Nm M8 M A = 20 Nm [ ] Please note: Kathrein does not recommend to use counter nuts. The additional nuts supplied are only meant as spares. All dimensions in mm and [inches] Page 1 of 1

General Instructions for Adjustment Mechanism Description of the adjustment mechanism (protective cap

➁ Downtilt spindle with integrated scale.

The lower edge of the gearwheel must be used for alignment. Manual adjustment procedure: 0 max.

6 General Instructions for Adjustment Mechanism Description of the adjustment mechanism (protective cap removed): ➀ Adjustment wheel with twist-lock function. ➁ Downtilt spindle with integrated scale. ➀ Thread for fi xing the pro tective cap or the RCU (Remote Control Unit). ➁ Gearwheel for RCU power drive. To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gearwheel must be used for alignment. Manual adjustment procedure: 0 max. 0 max. Remove the protective cap. Set downtilt angle by rotating the adjustment wheel. Screw on the protective cap again. Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment: /a Subject to alteration. For a description of RCU installation please refer to the respective data sheet. Page 1 of 2

General Instructions for Feederline Installation for Triple- and Quad-band Antennas Please note: To avoid any damage to the interfaces, please ensure that only suitable tools are used.

Description of bottom end cap (exemplary picture): Ventilation hole Adjustment mechanism (protective cap removed) Spindle with tilting scale 7-16 female (long neck) Colour coding: Correlation of each

Installation of the feederline connector and RCU (optional): In order to protect the adjustment mechanism the protective caps have to be attached during feederline installation!

7 General Instructions for Feederline Installation for Triple- and Quad-band Antennas Please note: To avoid any damage to the interfaces, please ensure that only suitable tools are used. To tighten the feederline connector interfaces, we strongly recommend using a special Kathrein installation tool (as shown below) in combination with a standard torque-wrench. Description of bottom end cap (exemplary picture): Ventilation hole Adjustment mechanism (protective cap removed) Spindle with tilting scale 7-16 female (long neck) Colour coding: Correlation of each RF input to: the corresponding adjustment mechanism the frequency range the polarization There are eight feederline connectors and four adjustment mechanisms located at the bottom of the antenna. Installation of the feederline connector and RCU (optional): In order to protect the adjustment mechanism the protective caps have to be attached during feederline installation! Kathrein installation set: Type No Set has to be ordered separately! Set consists of three spanners of 27, 32 and 41 mm width. For the feederline installation carefully put the connector in place and hand-screw the nut. Page 2 of 2 mm After feederline installation, the optional remote control units (RCU) R1, B1 and Y1 can be mounted if required. For a full description of RCU installation please refer to the respective data sheet. m 27 Use a torque-wrench to finish installation. 41 m These tools are suitable for 7-16 connectors with a wrench size of 27 or 32 mm, and the RCU attachment nut with a wrench size of 41 mm. Tighten nuts within a torque range of Nm depending on connector manufacturers specifications, respectively the RCU nut with a torque range of Nm /a 32 mm Subject to alteration. 1/2ß square actuation according to DIN 3120 Form C

6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by hand or by optional RCU (Remote Control Unit)

6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by hand or by optional RCU (Remote Control Unit) Frequency Range Dual Polarization HPB Adjust. Electr. DT 698 960 1710 2690 1710 2690 1 12 2 12 2 12 set by hand or by optional RCU (Remote Control Unit) X X 65 65 65 X 6-Port Antenna 698 960/1710 2690/1710