TC ANT MOBILE... Mobile communication antennas and antenna cables. Data sheet _en_00. 1 Description

Transcription

1 Mobile communication antennas and antenna cables Data sheet _en_00 PHOENIX CONTACT Description This data sheet describes the accessories for mobile communication products. All mobile communication products from Phoenix Contact have an SMA antenna connection. Therefore, you can use the following antennas: Designation Order No. Mounting Illustration PSI-GSM-STUB-ANT Mounting directly on the device TC ANT MOBILE WALL 5M Wall or mast mounting with mounting bracket, inside or outside PSI-GSM/UMTS-QB-ANT Installation on the control cabinet TC ANT MOBILE/GPS Furthermore, antenna cables are also available for extending to 5 meters or 10 meters. Make sure you always use the latest documentation. It can be downloaded at phoenixcontact.net/products. This data sheet is valid for all products listed on the following page:

2 Table of contents 1 Description Ordering data Antenna for mounting directly on the device: PSI-GSM-STUB-ANT Mounting Dimensions Antenna with mounting bracket: TC ANT MOBILE WALL 5M Safety notes Mounting with mounting bracket Mounting on a surface Lay the antenna cable Antennas for mounting on the control cabinet: PSI-GSM/UMTS-QB-ANT and TC ANT MOBILE/ GPS Mounting Antenna cable Ordering data Antennas Description Type Order No. Pcs./Pkt. GSM antenna for direct assembly on the device, angled antenna plug (90, SMA circular connector). The antenna is suitable for installation in plastic control cabinets not visible from the outside. Multiband mobile communication antenna with mounting bracket for outdoor installation. 5 m antenna cable with SMA circular connector GSM-UMTS antenna, with omnidirectional characteristics, 2 m antenna cable with SMA circular connector, for mounting on the control cabinet Combined mobile communication GPS antenna with omnidirectional characteristic, 2 m antenna cable with SMA circular connector (GSM/UMTS) and R-SMA circular connector (GPS) for mounting on the control cabinet PSI-GSM-STUB-ANT TC ANT MOBILE WALL 5M PSI-GSM/UMTS-QB-ANT TC ANT MOBILE/GPS Antenna cable Description Type Order No. Pcs./Pkt. GSM/UMTS antenna cable, 5 m long; SMA (male) -> SMA (female), 50 Ohm impedance GSM/UMTS antenna cable, 10 m long; SMA (male) -> SMA (female), 50 Ohm impedance PSI-CAB-GSM/UMTS- 5M PSI-CAB-GSM/UMTS-10M _en_00 PHOENIX CONTACT 2/7

3 3 Antenna for mounting directly on the device: PSI-GSM-STUB-ANT The antenna is suitable for installation in plastic control cabinets not visible from the outside. PSI-GSM-STUB-ANT MHz / 900 MHz / 1800 MHz / 1900 MHz / 2100 MHz Standing wave ratio VSWR in a 50 Ohm system Typical < 2.0 Gain Typical 0 db General data Function GSM omnidirectional antenna Ambient temperature range -40 C C Connection SMA circular connector, angled at 90 Dimensions Height Diameter 85.7 mm 10 mm 3.1 Mounting 3.2 Dimensions Ø7,8 Ø10 85,7 ² 90 20,5 25,6 Figure 2 Dimensions in mm Figure 1 Antenna for mounting directly on the device When installing in a control cabinet, reception may be so strongly impaired that trouble-free operation cannot be ensured. Use a GSM antenna with connection cable (e.g., , PSI-GSM/UMTS-QB-ANT) and mount it outside the control cabinet _en_00 PHOENIX CONTACT 3/7

4 4 Antenna with mounting bracket: TC ANT MOBILE WALL 5M This antenna is particularly suitable for mounting on inside or outside walls. TC ANT MOBILE WALL 5M MHz / 800 MHz / 850 MHz / 900 MHz / 1800 MHz / 1900 MHz / 2100 MHz / 2600 MHz Standing wave ratio VSWR in a 50 Ohm system < 2.50 Gain 700 MHz / 800 MHz 3dBi 900 MHz / 1800 MHz 4dBi 1900 MHz MHz 5dBi Maximum power 30 W Polarization Vertical General data Function 4.1 Safety notes Multiband mobile communication antenna with omnidirectional characteristics Ambient temperature range -40 C C Connection 5 m antenna cable with SMA circular connector Dimensions Height Diameter Antenna housing material WARNING: Risk of electric shock Parts of the antenna are electrically conductive. Contact with live cables can lead to death or serious injuries. The antenna and the mast must not be in the vicinity of live cables during installation or removal. If there is a risk of lightning strike: make sure that the antenna is mounted and grounded by qualified specialist personnel according to generally recognized technical regulations. WARNING: Fall hazard Make sure that the mounting location can be reached with the available equipment. 82 mm 48 mm ABS CAUTION: High frequency Mount the antenna such that there will not be anyone within a radius of 30 centimeters during operation. Figure 3 Antenna with mounting bracket _en_00 PHOENIX CONTACT 4/7

5 4.2 Mounting with mounting bracket Select the mounting location Mount the antenna vertically with the antenna cable downwards. Note that there must be a gap of at least 30 centimeters between the antenna and metallic parts or surfaces. Select the mounting location so that the antenna cable can be routed safely to the device. If you use screws, make sure that there is sufficient space behind the mounting area. Only use the mounting bracket supplied. Other brackets could impair the performance of the antenna. Select an antenna position providing good wireless network conditions. Mounting You can fix the mounting bracket using the four 5.5 mm fixing holes. Use M5 machine screws or self-tapping screws. You can use the bracket as a drilling template. Alternatively, you can fix the mounting bracket to a mast. Fix the bracket using a worm drive clip with a maximum width of 14 mm. Fix the antenna firmly to the mounting bracket with the nut and washer supplied. If you wish to mount the antenna permanently, you can also use the adhesive surface on the underneath of the antenna. In this case, make sure that the surface of the bracket is clean and dry. Pull the foil off the adhesive surface and press the antenna firmly onto the bracket. 4.3 Mounting on a surface Select the mounting location For optimum performance, you must mount the antenna on a sufficiently dimensioned electrically conductive grounding plate. Plates with a thickness of 1 mm mm and a diameter of at least 200 mm are suitable. Note that there must be a gap of at least of 30 centimeters between the antenna and other metallic parts. Make sure that there is sufficient space underneath the mounting surface. Mounting Cover the plate around the hole to be drilled in order to protect the surface. Drill a small hole and enlarge it to a diameter of 14 mm. Make sure that you do not damage any parts underneath the drill hole with the drill. Clean the surface surrounding the drill hole and remove any chipping. Remove paint and primer on the underneath of the plate so that sufficient electrical contact is ensured via the washer and the nut. Remove the washer and the nut from the antenna. Pull the foil off the adhesive surface. Feed the antenna cable through the drill hole. Press the antenna firmly onto the plate. Secure the antenna underneath the plate with the washer and the nut. Tighten the nut. 4.4 Lay the antenna cable Route the antenna cable to the device. Do not route the cable in the immediate vicinity of other cables. Make sure that moving parts do not knock the antenna cable _en_00 PHOENIX CONTACT 5/7

6 5 Antennas for mounting on the control cabinet: PSI-GSM/UMTS-QB-ANT and TC ANT MOBILE/GPS Gain 800 MHz / 900 MHz 1800 MHz / 1900 MHz 2100 MHz GPS PSI-GSM/UMTS-QB-ANT TC ANT MOBILE/GPS MHz / 900 MHz / 1800 MHz / 1900 MHz / 2100 MHz 5dBi 5dBi 3dBi 3dBi 1dBi 1dBi - 25 dbi General data Function 5.1 Mounting Multi-band mobile communication antenna for UMTS and quad band GSM, with omnidirectional characteristics Combined mobile communication GPS antenna with omnidirectional characteristics Ambient temperature range -40 C C -25 C C Connection 2 m antenna cable with SMA circular connector 2 m antenna cable with SMA circular connector (GSM/UMTS) and R-SMA circular connector (GPS) Dimensions Height Diameter 20 mm 76 mm 23 mm 76 mm Degree of protection - IP69K Figure 4 Antenna for mounting on the control cabinet Figure 5 Installation on the control cabinet Drill a hole with a diameter of 16.5 mm into the top of the control cabinet. When mounting, please note that: the antenna has a diameter of 76 mm. The cable is 2 meters long. Secure the antenna using the washer and nut provided _en_00 PHOENIX CONTACT 6/7

7 6 Antenna cable The antenna cables are equipped with SMA connector and socket respectively. You can simply mount it without an additional adapter between the antenna and device. PSI-CAB-GSM/UMTS- 5M PSI-CAB-GSM/UMTS-10M Length 5 meters 10 meters Impedance 50 Ω 850 MHz / 900 MHz / 1800 MHz / 1900 MHz / 2100 MHz Connection SMA (male) - SMA (female) Attenuation 850 MHz 900 MHz 1800 MHz 2100 MHz 0.23 db/m 0.24 db/m 0.35 db/m 0.39 db/m Bending radius, permanent 82 mm Outside diameter 5.5 mm Material of outer cable sheath Ambient temperature Operation Storage/transport LSFH -40 C C -40 C C We recommend using only one of these cables in applications. Otherwise attenuation is too high. Figure 6 Antenna cable _en_00 PHOENIX CONTACT GmbH & Co. KG Flachsmarktstraße Blomberg Germany 7/7 phoenixcontact.com