FORMIKE ELECTRONIC CO.,LTD

Size: px

Start display at page:

Download "FORMIKE ELECTRONIC CO.,LTD"

Arnold Hunter
5 years ago
Views:

1 PRODUCT SPECIFICATION TFT LCD MODULE MODEL : KWH104KQ05-F01 Preliminary Specification Finally Specification CUSTOMER'S APPROVAL SIGNATURE: DATE: APPROVED PM PD PREPARED BY REVIEWD REVIEWD BY Kam / Stephen Roy Prepared By : Address :Room 14H, HanKing Building, 23# DengLiang Road, NanShan District, ShenZhen, , China. TEL:(86) , FAX:(86) This specification is subject to change without notice.please contact FORMIKE or it's representative before designing your product based on this specification. 1/18 Issued Date: Feb

2 TABLE OF CONTENTS N0 CONTENTS PAGE 0 TABLE of CONTENTS 2 0 RECORD of REVISION 3 1 SUMMARY 4 2 FEATURES 4 3 GENERAL SPECIFICATIONS 4 4 OUTLINE DRAWING 5 5 PIN CONNECTION 6 6 ABSOLUTE MAXIMUM RATING 8 7 ELECTRICAL CHARACTERISTICS 8 8 DC CHARACTERISTICS 9 9 AC CHARACTERISTICS OPTICAL CHARACTERISTICS BLOCK DIAGRAM QUALITY ASSURANCE PRECAUTIONS FOR USE /18

3 0 Record of Revision Version Issued Date Page Content Created or Modified by Dec-5 All New Creation Tom Feb-10 The first version final specification Stephen 3/18

4 1. Summary KWH104KQ05-F01is a transmissive type color active matrix liquid crystal display (LCD), which uses amorphous thin film transistor (TFT) as switching devices. This panel has a 10.4 inches diagonally measured active display area with SVGA (800 RGB x 600) resolution. The following describes the features of this product. 2. Features 10.4 (diagonal) inch configuration SVGA ( pixels) resolution 3. General Specifications No. Item Specification Unit 1 Screen Size 10.4 (Diagonal) inch 2 Display Resolution 800 RGB x 600 pixel 3 Dot Pitch (H) x (V) mm 4 Pixel Pitch (H) x0.264 (V) mm 5 Active Area 211.2(H) x 158.4(V) mm 6 Outline Dimension (H) x (V) x 5.9 (D) mm 7 Pixel Configuration RGB-Stripe -- 8 Color Depth 16.2M colors 9 LCD Type TN Interface Type Digital 24bit RGB Surface Treatment 3H View direction (Gray inversion) 6 o clock Weight 390 g 4/18

5 4. Outline Drawing 5/18

6 5. Interface Pin Connection Pin Symbol I/O Function Remark 1 GND G Power Ground 2 AVDD P Analog input voltage 3 VCC P Digital input voltage 4 R0 I Red data input (LSB) 5 R1 I Red data input 6 R2 I Red data input 7 R3 I Red data input 8 R4 I Red data input 9 R5 I Red data input 10 R6 I Red data input 11 R7 I Red data input (MSB) 12 G0 I Green data input (LSB) 13 G1 I Green data input 14 G2 I Green data input 15 G3 I Green data input 16 G4 I Green data input 17 G5 I Green data input 18 G6 I Green data input 19 G7 I Green data input (MSB) 20 B0 I Blue data input (LSB) 21 B1 I Blue data input 22 B2 I Blue data input 23 B3 I Blue data input 24 B4 I Blue data input 25 B5 I Blue data input 26 B6 I Blue data input 27 B7 I Blue data input (MSB) 28 CLKIN I Dot clock input 29 DEN I Data enable signal 30 HSD I HSYNC signal 31 VSD I VSYNC signal 32 MODE I H: DE mode (Default) L: SYNC mode 6/18

7 33 NC I No connect (please leave it open) 34 NC I No connect (please leave it open) 35 NC - No connect (please leave it open) 36 VCC P Digital input voltage 37 NC - No connect (please leave it open) 38 GND G Power Ground 39 GND G Power Ground 40 AVDD P Analog input voltage 41 VCOM P VCOM DC input 42 DITH I Dithering function setting H: Disable dithering function L: Enable dithering function 43 NC - No connect (please leave it open) 44 VCOM out O connect a capacitor 45 NC No connect (please leave it open) 46 NC No connect (please leave it open) 47 NC No connect (please leave it open) 48 NC No connect (please leave it open) 49 NC No connect (please leave it open) 50 NC No connect (please leave it open) 51 NC No connect (please leave it open) 52 NC No connect (please leave it open) 53 NC No connect (please leave it open) 54 NC No connect (please leave it open) 55 NC - No connect (please leave it open) 56 VGH P TFT turn on voltage 57 VCC P Digital input voltage 58 VGL P TFT turn off voltage 59 GND G Power Ground 60 NC - No connect (please leave it open) Note: (1) Suggested connector: MT-FP160N-2FR (UJU)or any equivalent 7/18

8 6. Absolute Maximum Rating (Ta = 25 ± 2 ) Item Symbol Values Min. Max. Unit Note Storage Temperature T ST Operation Temperature T OP Digital Supply Voltage VCC V (2) Analog Power Supply Voltage AVDD V (3) TFT Device on voltage V GH V (4) TFT Device off voltage V GL V GH V (4) Note: (1) All of the voltages listed above are with respective to GND= 0V (2) Device is subject to be damaged permanently if stresses beyond those absolute maximum ratings listed above. 7. Electrical Characteristics 7-1. Operating Conditions: (Ta = 25 ± 2 ) Item Symbol Values Min. Typ. Max. Unit Note Digital Power Supply Voltage VCC V Digital Supply Current I CC ma Black Pattern Analog Power Supply Voltage AVDD V Analog Supply Current I AVDD ma Black Pattern TFT Device on voltage V GH - (18) - V TFT Device off voltage V GL - (-7) - V Common Electrode Driving Voltage VCOM V LED Reverse Voltage Vr 1.5 V For single LED LED Forward Current If ma For single LED 7-2. Backlight Driving Conditions: Note: (1) Brightess to be decreased to 50% of the initial value ma (Ta = 25 ± 2 ) Item Symbol Values Min. Typ. Max. Unit Note Power Consumption P BL W -- LED Current I F ma -- Backlight Voltage V BL V -- Life Time hrs (1) ma 8/18

9 8. DC Characteristics 8.1 Parameter Note: (1) For Digital Circuit (Ta = 25 ± 2 ) Item Symbol Values Min. Typ. Max. Unit Note Low Level Input Voltage V IL 0-0.3VCC V (1) High Level Input Voltage V IH 0.7 VCC - VCC V (1) 8.2 Power Sequence The LCD panel power ON/OFF sequence is as below Min. Typ. Max. Unit T ms T ms T3 T4 T5 T6 > 0 >0 >0 >0 ms ms ms ms 9/18

10 9. AC Characteristics 9.1. Data Timing (Under frame rate is equal to 60Hz) Horizontal Timing Parameter Symbol Spec Min. Typ. Max. Unit Horizontal Display Area thd 800 CLK CLK Frequency fclk MHz One Horizontal Line th CLK HS Pulse Width thpw 1-40 CLK HS Back Porch thb 46 CLK HS Front Porch thfp CLK Vertical Timing Parameter Symbol Spec Min. Typ. Max. Unit Vertical Display Area tvd 600 th VS Period Time tv th VS Pulse Width tvpw 1-20 th VS Back Porch tvb th VS Front Porch tvfp th Note: FORMIKE suggest using frame rate 60Hz to have better performance Horizontal Timing 10/18

11 Vertical Timing 9.2. AC Electrical characteristic Parameter Symbol Spec. Min. Typ. Max. Unit HS setup time T hst ns HS hold time T hhd ns VS setup time T vst ns VS hold time T vhd ns Data setup time T dsu ns Data hold time T dhd ns DE setup time T esu ns DE hold time T ehd ns VDD Power On Slew Rate T POR ms RSTB pulse width T Rst us CLKIN cycle time T cph ns CLKIN pulse duty T cwh % Output stable time T sst ns Repair OPA Output Stable time T Rsst ns 11/18

12 9.3. Input Clock and Data Timing Waveform 12/18

13 10.. Optical Characteristics (Ta = 25 ± 2, I F =20mA) Item Symbol Conditions Specifications Min. Typ. Max. Contrast Ratio CR Unit Note (2),(4), (6) Brightness B cd/m 2 T r ms Response time (3) T f Viewing ms Rx normal Red angle Ry θ= 0 Gx Green Φ = 0 Gy Chromaticity B/L On (2)(5)(6) Bx Blue By White Wx Wy Viewing Angle Hor. θ L θ R CR Ver. Φ T B/L On Φ B deg. (1) NTSC % Uniformity % (7) Note: (1) Definition of viewing angle range 13/18

14 Fig. 8-1 Definition of viewing angle (2) Test equipment setup: After stabilizing and leaving the panel alone at a driven temperature for 10 minutes, the measurement should be executed. Measurement should be executed in a stable, windless, and dark room. Optical specifications are measured by Topcon BM-7 luminance meter 1.0 field of view at a distance of 50cm and normal direction. Fig. 8-2 Optical measurement system setup (3) Definition of Response time: The response time is defined as the LCD optical switching time interval between White state and Black state. Rise time, Tr, is the time between photo detector output intensity changed from 90 to 10. And fall time, Tf, is the time between photo detector output intensity changed from10 to /18

15 (4) Definition of contrast ratio: The contrast ratio is defined as the following expression. Contrast ratio (CR)= Luminance measured when LCD on the White state Luminance measured when LCD on the Black state (5) Definition of color chromaticity (CIE 1931) Color coordinates measured at the center point of LCD (6) Measured at the center area of the panel when all the input terminals of LCD panel are electrically opened. Brightness (min) (7) Uniformity (U) = x 100% Brightness (max) 15/18

16 11. Block Diagram Out1 800 RGB x 600 LCD Panel Out 600 Gate Driver Q1 Q 2400 R, G, B 1 st ~ 60 th Source Driver 12. Quality Assurance No. Test Items Test Condition Note 1 High Temperature Storage Test Ta=70 Dry 240h 2 Low Temperature Storage Test Ta=-20 Dry 240h 3 High Temperature Operation Test Ta=60 Dry 240h 4 Low Temperature Operation Test Ta=-10 Dry 240h 5 High Temperature and High Humidity Operation Test 6 Electro Static Discharge Test 7 Shock Test (non-operating) 8 Vibration Test (non-operating) 9 Thermal Shock Test Ta=50 80%RH 240h Panel surface / top case Contact / Air ±6KV / ±15KV 150pF 330Ω Shock Level : 100G Waveform: Half Sinusoidal wave Shock Time : 6ms 3 Axis for all six faces/ each Random Vibration G 2 /Hz from 5-200Hz -6dB/ octave from Hz -10 (0.5Hr) ~ +60 (0.5Hr) for 100 cycles Note: (1) All the cosmetic specifications are judged before the reliability stress. Non-operating 16/18

17 13.PRECAUTIONS FOR USE 13.1.Safety (1) Do not swallow any liquid crystal, even if there is no proof that liquid crystal is poisonous. (2) If the LCD panel breaks, be careful not to get liquid crystal to touch your skin. (3) If skin is exposed to liquid crystal, wash the area thoroughly with alcohol or soap Storage Conditions (1) Store the panel or module in a dark place where the temperature is 23±5 C and the humidity is below 50±20%RH. (2) Store in anti-static electricity container. (3) Store in clean environment, free from dust, active gas, and solvent. (4) Do not place the module near organics solvents or corrosive gases. (5) Do not crush, shake, or jolt the module. (6) Do not exposed to direct sun light of fluorescent lamps Installing LCD Module Attend to the following items when installing the LCD Module. (1) Cover the surface with a transparent protective plate or touch panel to protect the polarizer and LC cell. (2) When assembling the LCD Module into other equipment, the spacer to the bit between the LCD Module and the fitting plate should have enough height to avoid causing stress to the module surface, refer to the individual specifications for measurements. The measurement tolerance should be ±0.1mm Precautions For Operation (1) Viewing angle varies with the change of liquid crystal driving voltage (Vo). Adjust Vo to show the best contrast. (2) Driving the LCD in the voltage above the limit will shorten its lifetime. (3) Response time is greatly delayed at temperature below the operating 17/18

18 temperature range. However, this does not mean the LCD will be out of the order. It will recover when it returns to the specified temperature range. (4) When turning the power on, input each signal after the positive/negative voltage becomes stable. (5) Do not apply water or any liquid on product which composed of T/P Handling Precautions (1) Avoid static electricity which can damage the CMOS LSI; please wear the wrist strap when handling. (2) The polarizing plate of the display is very fragile. so, please handle it very carefully. (3) Do not give external shock. (4) Do not apply excessive force on the surface; it may cause display abnormal. (5) Do not wipe the polarizing plate with a dry cloth, as it may easily scratch the surface of plate. (6) Do not use ketonics solvent & Aromatic solvent, use with a soft cloth soaked with a cleaning naphtha solvent. (7) Do not operate it above the absolute maximum rating. (8) Do not remove the panel or frame from the module. (9) Do not apply water or any liquid on product, which composed of T/P Warranty (1) The period is within 12 months since the date of shipping out under normal using and storage conditions. (2) The warranty will be avoided in case of defect induced by customer. 18/18

ZETTLER DISPLAYS SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY XIAMEN ZETTLER ELECTRONICS CO., LTD. CUSTOMER APPROVAL

ZETTLER DISPLAYS SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY CUSTOMER APPROVAL PART NO. : ATM1040D3 (ZETTLER DISPLAYS) VER1.0 COMPANY APPROVAL CHOP CUSTOMER COMMENTS ZETTLER DISPLAYS ENGINEERING APPROVAL