Limelight by Lutron Wireless Lighting Control System

Size: px

Start display at page:

Download "Limelight by Lutron Wireless Lighting Control System"

Stephen Chambers
5 years ago
Views:

Limelight by Lutron Wireless Lighting Control System 3691100d 1 10.16.18 Limelight by Lutron is a wireless lighting control system for exterior parking garage and parking lot applications.

Features Typical jobs require a single gateway without a need for wireless repeaters. A cellular gateway option eliminates the need to get an Ethernet connection.

Fixtures can be grouped together to turn an entire floor on at once to make sure there is plenty of light available in safety-critical areas.

1 Limelight by Lutron Wireless Lighting Control System d Limelight by Lutron is a wireless lighting control system for exterior parking garage and parking lot applications. Limelight by Lutron uses a high-density mesh wireless technology to communicate between the Limelight gateway and the Limelight nodes at every luminaire. Features Typical jobs require a single gateway without a need for wireless repeaters. A cellular gateway option eliminates the need to get an Ethernet connection. Single sign-on for Lutron interior and exterior controls when connected to Enterprise Vue. Fixtures can be grouped together to turn an entire floor on at once to make sure there is plenty of light available in safety-critical areas. In areas with cameras, the unoccupied level can be set to a reduced light level instead of OFF. Limelight by Lutron uses sensors to intelligently reduce power consumption and will monthly reports of energy usage data. limelight LL-ETHGATE LL-CELLGATE LL-EXTMOUNT LL-INTMOUNT LL-PIR * Controls inside the box are integrated into the fixture Model Number Installation to Fixture Description LL-ETHGATE N/A Limelight by Lutron Gateway Panel Assembly Ethernet based LL-CELLGATE N/A Limelight by Lutron Gateway Panel Assembly Cellular based LL-PIR-L OEM Limelight by Lutron PIR Sensor Assembly for 8 to 15 ft (2.5 to 4.6 m) mounting height LL-PIR-M OEM Limelight by Lutron PIR Sensor Assembly for 16 to 30 ft (4.9 to 9 m) mounting height LL-PIR-H OEM Limelight by Lutron PIR Sensor Assembly for 31 to 40 ft (9.5 to 12 m) mounting height LL-INTMOUNT OEM Limelight by Lutron Radio Module PCB Assembly LL-EXTMOUNT-L Field retrofit Limelight by Lutron UL Listed Field-installable Radio Sensor Module (RSM) - for 8 to 15 ft (2.5 to 4.6 m) mounting height LL-EXTMOUNT-M Field retrofit Limelight by Lutron UL Listed Field-installable Radio Sensor Module (RSM) - for 16 to 30 ft (4.9 to 9 m) mounting height LL-EXTMOUNT-H Field retrofit Limelight by Lutron UL Listed Field-installable Radio Sensor Module (RSM) - for 31 to 40 ft (9.5 to 12 m) mounting height

2 System Components Limelight by Lutron Enabled Luminaire The Limelight by Lutron wireless radio sensor module (RSM) is currently integrated into a variety of luminaires. Fixtures with an integrated RSM can turn on/off and provide full dimming drive capability using 0 10 V. A Limelight by Lutron enabled fixture requires no special communication wiring or special installation instructions. Installation is equivalent to a simple (non- Limelight) luminaire. When AC ( V~) power is applied, the fixture powers up with a factory default setting of 100% light output until the Limelight by Lutron commissioning process begins. Contact Lutron for assistance in identifying current OEM fixture offerings for your application. Limelight by Lutron Gateway The gateway serves as the communication hub between the RSMs and the Web User Interface. Up to 800 RSMs per gateway. Installs in a utility closet or ceiling mounted nearest the center of the RF mesh. Connects to the internet via an Ethernet cable or cellular connection. Secured in an IP65 tamper-proof housing. Through an internet connection, the gateway communicates to the cloud server. Fixtures can be grouped into multiple zones, operating hours established, with information on the system s status and performance immediately available. Every fixture in the system is individually addressable d Limelight by Lutron Radio Sensor Module (RSM) Every RSM has a fully integrated wireless radio. The radios leverage the Zigbee communication (IEEE ) protocol, with high-density mesh technology built on top. These radios provide: A robust, redundant communications scheme. Communication between multiple floors above or below in parking facilities. Each radio communicates to the neighbor radios around it, creating a high-density mesh (on average, each radio will be in communication with 8 to 12 other radios). This redundant communications system enables Limelight by Lutron to be self-healing. If a radio ever stops functioning or is vandalized, the other radios will immediately search out and establish communication with other neighbors in the mesh. This high-density mesh system enables the Limelight by Lutron control system to operate smoothly even in the most difficult conditions. Occupancy Sensor: Projecting from the underside of each of the radios is a passive infrared occupancy sensor. e Maintains up to 30 ft (9 m) diameter coverage at 8 ft (2.5 m) high. e Creates maximum coverage of the garage floor. e Captures all sensing activity (time of day and fixture number) in a centralized database for activity reporting and analysis. Daylight Sensor: Daylight harvesting capabilities are supported. e Provides daylight measure every 15 minutes (programmable). e Measures foot candles per fixture to analyze for maximum harvesting capability.

3 Specifications d Limelight by Lutron Gateway Panel Assembly Models LL-ETHGATE Ethernet Based LL-CELLGATE Cellular Based 3 years of cellular data is included in the price of the LL-CELLGATE For additional cellular contract lengths, please contact your local Lutron representative Standards For commercial use, Class A only culus Listed FCC / IC RSS-247 Power Maximum current draw: 120 V~ 60 Hz 0.3 A Maximum power consumption: 15 W (51.2 BTU/hr) Power Cord (standard 3-prong plug) AC Power Indicator LED (green) Operating Temperature -4 F 122 F (-20 C 50 C) Physical Dimensions: 10.3 in (261.6 mm) x 6.3 in (160 mm) x 5.5 in (139.7 mm) Lock Protection capable (padlock not provided) Solid body: ABS/PC plastic, UL94-5VB flammability rating Clear cover: Polycarbonate plastic with UL94V-0 flammability rating, UV stabilized AC power cord: Black, 5 ft (1.5 m), straight plug to standard 120 V~ outlet (receptacle required) Mounting Four (4) mounting brackets pre-attached Wall anchors (supplied by others) Mount vertical with space for field service access to side connectors Not intended for direct exposure to the elements Location Recommendations Maintenance closet or environment-friendly location Mount away from dense metal obstructions (maintain at least 2 ft [0.6 m]) Nearest to the middle of the RF Mesh/Parking facility preferred Connections Ethernet (LL-ETHGATE only) CAT5 (or equivalent) cable, straight-through wiring (T568B) cable supplied by others Field wired with RJ45 Ethernet plug (by others) Waterproof mating connector Cellular (LL-CELLGATE only) QuickCarrier USB - with SIM Socket GSM 3G HSPA+ technology Mount to wall and power on For LL-ETHGATE, also connect Ethernet At startup, display will confirm connection to cloud services Warranty continued on next page...

4 Specifications (continued) d Limelight by Lutron Gateway Panel Assembly (continued) Housing Model Dimensions Materials Industrial Standards External Connectors NBE BOX ABS/PC Body: ABS/PC blended plastic UL508, Type 1, 2, 4, 4x Waterproof RJ-45 (Bud Industries) in (286 mm) L x UL94-5VB flammability rating NEMA Type 1, 2, 3, 4 Ethernet connection or equivalent 7.48 in (190 mm) W Cover: polycarbonate plastic for ETH0 UL94V-0 flammability rating Internal Components Latches and hinges non-metallic Cover includes polyurethane gasket Power Supply Computer Radio Module M2M Cellular Modem FSP036-RAB UL Listed power supply Input voltage range: V~ 1.5 A Hz Output 12 V- at 3 A (36 W) Lockable DC jack design Intel Atom N GHz dual core processor or equivalent RJ-45 port10/100basetx Ethernet Controller USB 2.0 connection RS-232 serial communication Zigbee RF USB Module Transmit power 1 mw (0 dbm) Operating frequency 2.45 GHz GSM 3G HSPA+ technology AT command compatible Antenna mounted on top of gateway housing continued on next page...

5 Specifications (continued) d Limelight by Lutron Radio Module PCB Assembly Model LL-INTMOUNT Standards RoHS Compliant FCC /IC RSS-247 culus Recognized for internal mounting at a fixture OEM Power Requirements Input power: V~ (± 10%) 50/60 Hz Device consumption: 1.0 W (load enabled) 0.5 W (load disabled) Maximum Load: Electronic ballast: 5 A at 120 V~ 3.65 A at 277 V~ Environment -40 F 176 F (-40 C 80 C) Radio Sensor Module Control up to a 1000 W luminaire Power Measurement Accuracy +/- 5% Isolated 0 10 V- dimming output, capable of sinking up to 1.0 ma of 0 10 V- signal On board temperature sensor, accurate to +/-2 C 4 pin terminals for remote connection to LL-PIR Relay Maximum Inrush Current rating: 270 A for 1.05 ms Integrated ZigBee radio transceiver IC and FCC approved Title 47 Part 15 Subpart B and Subpart C section for Digital Transmission Systems Operating within the band MHz RF transmissions security: 128 AES plus application layer Can be configured to control non-dim loads Warranty Note: Outdoor fixtures should be minimum IP-65 rated continued on next page...

6 Specifications (continued) d Limelight by Lutron PIR Sensor Assembly Model LL-PIR Standards culus Recognized (for internal mounting at a fixture OEM) IP66 capable (when lens assembly is installed correctly at fixture manufacturer) Power Requirements V- (provided by LL-INTMOUNT) 50 mw maximum (20 mw typical) Operating Temperature -40 F 158 F (-40 C 70 C) Occupancy Sensor Assembly UL rated silicone washer for water and dust seal (IP66 wet locations) Threaded nut for secure fit 4-wire harness with low profile connector Features Reduced false triggers for more energy savings Small footprint allows it to fit almost anywhere Wide or narrow field of view with wireless settings adjustment Wirelessly choose between multiple profiles to optimize settings for various environments (flat lot, parking deck, high wind, various heights 8 40 ft [ m]) Integrated Daylight Sensor measures light to 1500 fc On board temperature sensor, accurate to +/-2 C LED with wireless brightness adjustment to provide user feedback Wireless field re-programmable Recommended mounting heights (8 40 ft [ m]) Low: 8 15 ft ( m) (ex. parking garage) Medium: ft (4.9 9 m) (ex. pole lights) High: ft ( m) (ex. specialty poles) Occupancy detection can be disabled (ships disabled, requires system activation to enable) Daylight Sensor can be disabled independently of occupancy detection Warranty Note: Outdoor fixtures should be minimum IP-65 rated continued on next page...

7 Specifications (continued) d Limelight by Lutron UL Listed Field-installable Radio Sensor Module (RSM) Model LL-EXTMOUNT Standards culus Listed UL244A UL773A CSA 22.2 No. 205 IP66 FCC /IC RSS-247 Power Requirements V~ (± 10%) 50 / 60 Hz 1.0 W (load enabled) 0.5 W (load disabled) Operating Temperature -40 F 158 F (-40 C 70 C) External Housing Aluminum Alloy 0.5 in (12.7 mm) NPT thread male Silver color only Installation The Limelight by Lutron UL Listed RSM must be physically connected to a conductive surface that is earth grounded (i.e. conduit, junction box, luminaire, etc.) The Limelight by Lutron UL Listed RSM should always be mounted with the occupancy sensor lens pointing toward the ground surface The internal RF antenna polarization is optimized to work best when the occupancy sensor lens pointing toward the ground surface See wiring diagram for details. If being used as a non-dim load controller, cap the violet wire and cap the gray wire Water Ingress The UL Listed RSM has been tested to the IP66 (wet locations) dust and water ingress protection standards Mounting Regardless of whether factory or field installed, it is the responsibility of the installer to attach the Limelight by Lutron to the fixture in a manner that maintains the IP66 integrity Lutron will only warranty water ingress issues if proper attachment methods are observed and documented Wet Location Mounting An excellent method of attachment to a fixture is a Myers Hub (not included) There are a variety of styles depending on the luminaire type, environment and desired occupancy coverage Ensure that the Myers Hub includes an O-ring gasket that has excellent environmental ratings When using a Myers Hub, the best solution is to use a thread sealant. If thread sealant is not available, apply high torque in all areas Observe all local codes Warranty continued on next page...

8 Specifications (continued) d Limelight by Lutron UL Listed Field-installable Radio Sensor Module (RSM) (continued) Radio Sensor Module Control up to a 1000 W luminaire Power Measurement Accuracy +/- 5% Isolated 0 10 V- dimming output, capable of sinking up to 1.0 ma of 0 10 V- signal On board temperature sensor, accurate to +/-2 C Relay Maximum Inrush Current rating: 270 A for 1.05 ms Integrated ZigBee radio transceiver IC and FCC approved Title 47 Part 15 Subpart B and Subpart C section for Digital Transmission Systems Operating within the band MHz RF transmissions security: 128 AES plus application layer Can be configured to control non-dim loads

9 Dimensions Dimensions shown as in (mm) LL-ETHGATE LL-CELLGATE d Mounting Brackets (4) Mounting Brackets (4) limelight limelight 10.3 (261.6) 10.3 (261.6) Cloud Connection Status Rev 2.3 DISPLAY Cloud Connection Status Rev 2.3 DISPLAY ETH0 PWR LED PWR LED 5.5 (139.7) 6.3 (160) 5.5 (139.7) 6.3 (160) LL-INTMOUNT 1.24 (31.4) 1.12 (28.5) 0.57 (14.5) Top View Tallest component approx. 0.8 (20.3) Tallest component approx (4) Bottom View 2.69 (68.3) 1.12 (28.5) 0.19 (4.8) 0.24 (6.19) 0.57 (14.5) (21) 0.57 (14.5) 0.24 (6.19) 1.12 (28.5) Holes Ø2.751 (Ø69.9) Clearance areas both sides of PCB Ø0.23 (Ø5.84) 1.12 (28.5) Ø2.751 (Ø69.9) 0.57 (14.5) continued on next page...

10 Dimensions (continued) Dimensions shown as in (mm) LL-PIR d (38.09) 1.08 (27.47) Ø0.99 (Ø25.29) Ø1.18 (Ø29.94) Ø0.06 (Ø1.69) LL-PIR-L Lens LL-PIR-M Lens LL-PIR-H Lens (60.375) (60.375) 3.17 (80.5) (22.225) (22.225) LL-PIR Lens assembly 1.07 (27.16) LL-PIR PCB assembly Nut (supplied) Fixture Gasket (supplied)

11 Dimensions (continued) Dimensions shown as in (mm) d LL-EXTMOUNT Ø4.409 (Ø112.0) 2.24 (56.8) 1.74 (44.17) 1/2-14 NPT threads

LL-INTMOUNT Wiring Diagram (LL-INTMOUNT / LL-PIR) Luminaire Power Connection Line/ Hot Neutral LED

12 LL-PIR Wiring d Connector is polarized so that it cannot be inserted in the wrong orientation To LL-PIR To LL-INTMOUNT Wiring Diagram (LL-INTMOUNT / LL-PIR) Luminaire Power Connection Line/ Hot Neutral LED Driver Switched Hot Dimming LL-INTMOUNT LL-PIR Dimming Ground Wiring Diagram (LL-EXTMOUNT) Luminaire Power Connection LED Driver Line/ Hot Neutral Switched Hot Dimming Dimming Ground LL-EXTMOUNT

13 Coverage All units on the graph are shown in ft (m) Limelight by Lutron PIR d Limelight by Lutron PIR can be configured wirelessly to have different profiles depending on its environment. Profile can be adjusted (in the software) to reduce coverage. Height: 8 ft (2.4 m), LL-PIR-L and LL-EXTMOUNT-L: 22.5 (6.8) 15 (4.5) 7.5 (2.3) 0 36 (11) 7.5 (2.3) 15 (4.5) 22.5 (6.8) 22.5 (6.8) 15 (4.5) 7.5 (2.3) (2.3) 15 (4.5) 22.5 (6.8) 0 8 (2.4) 18 (5.5) (2.4) (1.5) (0.6) (0.6) (1.5) (2.4) 18 (5.5) Height: 20 ft (6 m), LL-PIR-M and LL-EXTMOUNT-M 20 (6) 0 10 (3) 0 10 (3) 40 (12.1) 5 (1.5) 10 (3) 15 (4.5) 20 (6) 20 (6) (6) 20 (6) 20 (6) (5.4) (4.5) (3.6) (2.7) (1.8) (0.9) (0.9) (1.8) 9 (2.7) 12 (3.6) 15 (4.5) 18 (5.4) 20 (6) Height: 40 ft (12.1 m), LL-PIR-H and LL-EXTMOUNT-H 50 (15.2) 50' 25 (7.6) 25' 00' ' (30.4) 25' (7.6) 50 (15.2) 50' 50' (15.2) 25' (7.6) 0' 0 25' (7.6) 50' (15.2) 0' 0 15' (4.5) 27' (8.2) 40' (12.1) 50' 40' 30' 20' 10' 0' 0 10' 20' 30' 40' (15.2) (12.1) (9.1) (6) (3) (3) (6) (9.1) (12.1) 50' (15.2)

Technical System Overview 3691100d 14 10.16.18 Log in using Enterprise Vue (sold separately) or direct access to the Limelight by Lutron cloud server (included with system).

14 Technical System Overview d Log in using Enterprise Vue (sold separately) or direct access to the Limelight by Lutron cloud server (included with system). Lutron Cloud Platform Web-Based Interface Capabilities Ability to turn all fixtures on (via override) with a single button Ability to run diagnostics on a fixture Ability to check fixture status and identify errors Ability to flash any fixture Ability to see the total number of connected luminaries Gateway Wireless high-density mesh to luminaries Cellular or Ethernet to the cloud Wall-mounted inside a facility utility closet Limelight by Lutron Enabled Luminaire Each luminaire is shipped with the Limelight by Lutron radio and sensor integrated into the luminaire A retrofit (external mount) is also available Each Limelight by Lutron radio has occupancy and daylight sensors Up to 800 luminaires controlled by a single gateway as long as no other range restrictions are violated * * For Parking Garages, nodes should be no further than 4 floors above or below the gateway. (i.e. If the gateway is on floor 1, then nodes can be on floors 1 5. If the gateway is on floor 5, then nodes can be on floors 1 9).

15 Technical System Overview (continued) d Web-based Interface Standalone system OR Connect to Enterprise Vue for single login and navigation. See the Enterprise Vue Software spec submittal ( ) at for more information Wireless Range Best Practices RF range recommendations 3 nodes within this distance of the gateway Max distance from the gateway to any one node Max distance from node to node Gateway proximity to dense metal obstructions (including electrical panels) Max number of luminaires controlled by a single gateway Parking Garage Flat Lot 50 ft (15.2 m) 250 ft (76.2 m) 500 ft (152.4 m) 3000 ft (914.4 m) 50 ft (15.2 m) 300 ft* (91.4 m) Minimum 2 ft (0.6 m) away at height of no less than 6 ft (1.8 m) Up to 800, as long as no other range restrictions are violated. Nodes should be no farther than 4 floors above or below the gateway (i.e. If the gateway is on floor 1, then nodes can be on floors 1 5. If the gateway is on floor 5, then nodes can be on floors 1 9). Minimum 2 ft (0.6 m) away at height of no less than 6 ft (1.8 m) Up to 800, as long as no other range restrictions are violated * Nodes without a direct line of sight to another node should be placed no farther than 150 ft (45 m) apart.

Key Design Rules 3691100d 16 10.16.18 1. Maximum of 800 nodes per gateway 2.

16 Key Design Rules d Maximum of 800 nodes per gateway 2. Keep at least 3 nodes close to the gateway without dense metal between the gateway and the nodes. a. For a parking garage, keep within 50 ft (15 m) b. For a flat lot, keep within 250 ft (76 m)

17 Key Design Rules (continued) d Maximum distance from gateway to the farthest node a. For a parking garage, do not go further 500 ft (152.5 m) b. For a flat lot, 3000 ft (914.5 m) 4. Maximum node-to-node distance a. For a parking garage, the distance should not exceed 50 ft (15 m) b. For a flat lot, 300 ft (91.4 m) (nodes without a direct line of sight to another node should be placed no farther than 150 ft [45 m] apart)

18 Cloud Connection Status Rev x.x DISPLAY Cloud Connection Status Rev x.x DISPLAY Typical One-Line Diagram Components d To Limelight by Lutron cloud To network (QS-EO or Corporate Ethernet network) E LL-ETHGATE Limelight by Lutron gateway with Ethernet connection, IP65 rated (not intended for direct exposure to the elements), 120 V~ 60 Hz with 5 ft (1.5 m) power cord LL-CELLGATE Limelight by Lutron gateway with cellular connection, IP65 rated (not intended for direct exposure to the elements), 120 V~ 60 Hz with 5 ft (1.5 m) power cord LL-EXTMOUNT - (L/M/H) V~ 50/60 Hz, Limelight by Lutron, ULR Listed, field-installable, radio sensor module (RSM) with integral occupancy and daylight sensors RF signal to/ from gateway Switched Power, 1000 W max. RF signal to/ from gateway Switched Power, 1000 W max V- Dim 0 10 V- Dimming Switching Legend: Input power (normal) Two 12 AWG (4.0 mm 2 ) wires 0 10 V- Signal: Two 18 AWG (1.0 mm 2 ) wires E CAT5E or better cable for Lutron network terminated with RJ45 connectors (provided by others). 328 ft (100 m) maximum run )Lutron and Lutron are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries. Limelight is a trademark of TwistHDM, LLC. Zigbee is a trademark of Zigbee Alliance. UL is a trademark of UL LLC.

Installing the FSP-211 Sensor in Light Fixture

Installing the FSP-211 Sensor in Light Fixture (grey) WATTSTOPPER VOLTAGE HIGH/LOW/OFF PIR FIXTURE INTEGRATED OUTDOOR PHOTO/MOTION SENSOR Product Overview The is a passive infrared (PIR) outdoor sensor that raises or lowers the electric lighting level