TOSHIBA BIPOLAR DIGITAL INTEGRATED CIRCUIT SILICON MONOLITHIC TD62771AP

Transcription

1 TOSHIBA BIPOLAR DIGITAL INTEGRATED CIRCUIT SILICON MONOLITHIC 7CH HIGH VOLTAGE SOURCE DRIVER The is comprised of seven source current Transistor Array. This driver is specifically designed for fluorescent display applications. Applications include relay, hammer and lamp drivers. FEATURES High output voltage VCC = 60 V MIN. Output current (single output) IOUT = 50 ma MIN. Input compatible with TTL. 5 V CMOS Pull down resistors / each output Single supply voltage Package Type : DIP 16 pin Weight: 1.11 g (Typ.) CHARACTERISTIC DESIGNATION TTL, 5 V CMOS PIN CONNECTION (TOP VIEW) SCHEMATICS (EACH DRIVER) Note: The input and output parasitic diodes cannot be used as clamp diodes. 1

2 MAXIMUM RATINGS (Ta = 25 C) CHARACTERISTIC SYMBOL RATING UNIT Supply Voltage V CC 60 V Output Voltage V OUT V CC V Output Current I OUT 50 ma / ch Input Voltage V IN 20 V Power Dissipation P D (Note) 1.47 W Operating Temperature T opr 40~85 C Storage Temperature T stg 55~150 C Note: Delated above 25 C in the proportion of 11.7 mw / C RECOMMENDED OPERATING CONDITIONS (Ta = 40~85 C) CHARACTERISTIC SYMBOL TEST CONDITION MIN TYP. MAX UNIT Supply Voltage V CC V Output Voltage V OUT 0 V CC V Output Current I OUT 0 40 Input Voltage V IN 0 7 V Power Dissipation P D 0.52 W ma / ch ELECTRICAL CHARACTERISTICS (Ta = 25 C) Input Voltage CHARACTERISTIC SYMBOL TEST CIR CUIT TEST CONDITION MIN TYP. MAX UNIT H Level V IH L Level V IL Input Current H Level I IH µa Output Current L Level I OL 3 V IN = 2.4 V 200 µa Output Voltage Supply Current I H Level V OUT = 40 ma OH 4 V IN = V IH MIN. L Level V OL V CC 2.5 V CC 1.7 I OUT = 0, V IN = V IL MAX mv I CC (ON) 1 V CC = 55 V, V IN = V IH MIN. 20 I CC (OFF) V CC = 55 V, V IN = V IL MAX. 1 Turn On Delay t ON 5 V CC = 55 V, C L = 15 pf 0.2 µs Turn Off Delay t OFF 6.0 µs V V ma 2

3 TEST CIRCUIT 1. V IH, V IL, I CC 2. I IH 3. I OL 4. V OH, V OL 5. t ON, t OFF Note 1: Pulse width 50 µs, duty cycle 10% Output impedance 50 Ω, t r 100 ns, t f 100 ns Note 2: C L includes probe and jig capacitance PRECAUTIONS for USING This IC does not integrate protection circuits such as overcurrent and overvoltage protectors. Thus, if excess current or voltage is applied to the IC, the IC may be damaged. Please design the IC so that excess current or voltage will not be applied to the IC. Utmost care is necessary in the design of the output line, VCC and GND line since IC may be destroyed due to short circuit between outputs, air contamination fault, or fault by improper grounding. 3

4 4

5 PACKAGE DIMENSIONS DIP16 P A Unit: mm Weight: 1.11 g (Typ.) 5

6 RESTRICTIONS ON PRODUCT USE EBA TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the Handling Guide for Semiconductor Devices, or TOSHIBA Semiconductor Reliability Handbook etc.. The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ( Unintended Usage ). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer s own risk. The products described in this document are subject to the foreign exchange and foreign trade laws. The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. The information contained herein is subject to change without notice. 6

7 This datasheet has been download from: Datasheets for electronics components.