Features : 24V 48V RATED CURRENT 62.5A CURRENT RANGE 125A 0 ~ 125A 0 ~ 62.5A RATED POWER. 3000W RIPPLE & NOISE (max.) Note.

Transcription

1 P-000CC P ss 000W ingle Output Power upply Features : AC input ~ 6AC AC input active surge current limiting Conformal Coating High efficiency up to 90% Built-in active PFC function,pf>0.9 Protections: hort circuit / Overload / Over voltage / Over temperature / Fan alarm Forced air cooling by built-in DC with fan speed control function Output voltage can be trimmed between ~0% of the rated output voltage High power density.6w/inch Current sharing up to units Alarm signal output (relay contact and L signal) Built-in /0.A auxiliary output for remote control Built-in remote ON-OFF control Built-in remote sense function years warranty PECIFICAION P-000-CC P-000- P-000-CC P-000- P-000-8CC P DC OLAGE 8 AED CUEN 0A A 6.A CUEN ANGE 0 ~ 0A 0 ~ A 0 ~ 6.A AED POWE 0W 000W 000W IPPLE & NOIE (max.) Note. 0mp-p 0mp-p 0mp-p OLAGE ADJ. ANGE ~ 8 ~ 6.0%.0% MODEL OUPU INPU 0.8 ~. OLAGE OLEANCE Note..0% LINE EGULAION LOAD EGULAION 89.% 9 EUP, IE IME 0ms, ms at full load HOLD UP IME (yp.) 0ms at full load OLAGE ANGE ~ 6AC FEQUENCY ANGE 7 ~ 6Hz POWE FACO (yp.) 0.9/AC at full load EFFICIENCY (yp.) 86% AC CUEN (yp.) INUH CUEN (yp.) A/AC A/AC LEAKAGE CUEN <.0mA / AC OELOAD POECION OE OLAGE ~ 70DC 6A/AC ~ % rated output power User adjustable continuous constant current limiting or constant current limiting with delay shutdown after seconds, re-power on to recover 8.8 ~.6.8 ~ 6.8 OE EMPEAUE ILIAY POWE() Protection type : hut down o/p voltage, recovers automatically after temperature goes for emote ON/OFF control) EMOE ON/OFF CONOL FUNCION ALAM IGNAL OUPU OUPU OLAGE IM Note. CUEN HAING WOKING EMP. (), 0 (), 8 (), 0 (8) (W: detect on heatsink of power transistor) (), 7 (8) (W : detect on heatsink of o/p diode) Please see the Function Manual Please see the Function Manual. ~..8 ~ 8 - ~ +70 (efer to "Derating Curve") ~90% H non-condensing EMP. COEFFICIEN IBAION AFEY ANDAD AFEY & WIHAND OLAGE IOLAION EIANCE EMC EMC EMIION (Note ) 0.0%/ (0 ~ 0 ) 0 ~ 00Hz, G 0min./cycle, min. each along X, Y, Z axes UL90-, U EN90- approved EMC IMMUNIY MBF DIMENION PACKING NOE 9.6 ~ 6 Please see the Function Manual WOKING HUMIDIY ENIONMEN OAGE EMP., HUMIDIY OHE 7.6 ~ 67. Protection type : hut down o/p voltage, re-power on to recover - ~ +8, 0 ~ 9% H I/P-O/P:KAC I/P-:KAC O/P-:0.KAC I/P-O/P, I/P-, O/P-:M Ohms / 00DC / / 70% H Compliance to EN0 (CIP) Class B, EN60--,- Compliance to EN60--,,,,6,8,, EN0, light industry level, criteria A 0.K hrs min. MIL-HDBK-7F ( 78*77.8*6.mm (L*W*H) Kg; pcs/6kg/.89cuf ). All parameters NO specially mentioned are measured at AC input, rated load and of ambient temperature.. ipple & noise are measured at MHz of bandwidth by using a " twisted pair-wire terminated with a 0.uf & 7uf parallel capacitor.. olerance : includes set up tolerance, line regulation and load regulation.. he power supply is considered a component which will be installed into a final equipment. he final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on Can't use the PWM signal to control the output voltage. File Name:P-000PEC -09-

2 P-000CC P ss 000W ingle Output Power upply Mechanical pecification Case No.98B Unit:mm CN CN CN M(Both ides) L=mm M L=mm OUPU 6 Air flow direction + CN LED CN CN B 0 INPU 6max. AC Input erminal Control (CN,CN) : H DF-8DP-D or equivalent AC/L AC/N CG C P P,7 6 8 erminal Mating Housing (Current hare) H DF-8D H DF-**C or equivalent or equivalent CG: emote ON/OFF Ground C : emote ON/OFF P :Output oltage External Control P : eference oltage erminal : -emote ensing : Load hare : +emote ensing Control (CN) : H DF-0DP-D or equivalent GND GND 6 CG C GND: Power OK Ground : Power OK ignal (elay Contact) : Power OK ignal (L ignal) G OLP 0 CG: emote ON/OFF Ground C: emote ON/OFF G: Auxiliary Ground OLD Mating Housing erminal H DF-0D H DF-**C or equivalent or equivalent : Auxiliary Output OLP: OLP/OLD:OLP mode select PFC fosc : 88KHz PWM fosc : KHz Block Diagram I/P EMI FILE ACIE INUH CUEN LIMIING ECIFIE & PFC ECIFIE & FILE POWE WICHING PFC CONOL O..P. O..P. O.L.P. PWM CONOL LOAD HAING POWE DEECION CICUI EMOE CONOL C FAN ECIFIE & FILE POWE (/0.A) File Name:P-000PEC -09-

3 P-000CC P ss 000W ingle Output Power upply Derating Curve tatic Characteristics a= 90 0 LOAD (%) LOAD (%) AMBIEN EMPEAUE ( 70 (HOIZONAL) ) INPU OLAGE () Hz Function Manual.emote ON/OFF ()emote ON/OFF control becomes available by applying voltage in CN & CN & CN. ()able. shows the specification of emote ON/OFF function. ()Fig.. shows the example to connect emote ON/OFF control function. able. pecification of emote ON/OFF Connection Method Fig..(A) Output on W Open W Logic Output off W Close Fig..(B) W Open W Close Fig..(C) W Close W Open Fig.. Examples of connecting remote ON/OFF (A)Using external voltage source (B)Using internal auxiliary output K K C typ. W CG C typ. CG W G G (C)Using internal auxiliary output K typ. C K W CG G File Name:P-000PEC -09-

4 P-000CC P ss 000W ingle Output Power upply.alarm ignal Output ()Alarm signal is sent out through "" & " GND" and & GND pins. ()An external voltage source is required for this function. ()able. explain the alarm function built-in the power supply. Function Description Output of alarm(, elay Contact) Output of alarm(, L ignal) he signal is "Low" when the power supply is above Low (0. max at 00mA) Low (0. max at 0mA) % of the rated output voltage-power OK High or open he signal turns to be "High" when the power supply High or open is under % of the rated output voltage-power Fail (External applied voltage, 00mA max.) (External applied voltage, 0mA max.) able. Explanation of alarm 0.uF GND GND External voltage and (he max. sink is 00mA and ) External voltage and (he max. sink is 0mA and 0) Fig.. Internal circuit of (Open collector method) Fig.. Internal circuit of (elay, total is 0W).Output oltage IM ()Connecting an external DC source between P & on CN or CN, and &, & also need to be connected that is shown in Fig... ()Adjustment of output voltage is possible between ~0%(yp.) of the rated output which is shown in Fig... educing output current is required when the output voltage is trimmed up. out OP >% P ~6 Fig.. Add on ~6 external voltage OUPU CUEN (%) LOAD OUPU OLAGE (%) Non-Linear 6 EXENAL OLAGE (DC) OUPU OLAGE (%) Fig.. Output voltage trimming File Name:P-000PEC -09-

5 P-000CC P ss 000W ingle Output Power upply.current haring ()Parallel operation is available by connecting the units shown as below (, and are connected mutually in parallel): ()he voltage difference among each output should be minimized that less than 0. is required. ()he total output current must not exceed the value determined by the following equation. (Output current at parallel operation)=(he rated current per unit) x (Number of unit) x 0.9 () In parallel operation units is the maximum, please consult the manufacturer for other applications. () When remote sensing is used in parallel operation, the sensing wire must be connected only to the master unit. (6) Wires of remote sensing should be kept at least 0 cm from input wires. No.(Master) CN CN AC/L AC/N No.(lave) CN Load CN AC/L AC/N No.(lave) CN CN AC/L AC/N (7) When in parallel operation, the minimum output load should be greater than % of total output load. (Min. Load >% rated current per unit number of unit) (8) Under parallel operation, the "output voltage trim" function is not available..elect O.L.P mode ()emove the shorting connector on CN that is shown in Fig., the O.L.P. mode will be "continuous constant current limiting". ()Insert the shorting connector on CN that is shown in Fig., the O.L.P. mode will be "constant current limiting with delay shutdown after seconds, re-power on to recover. OLD OLD OLP OLP Fig.. emove the CN OLP Mode : constant current limiting Fig.. Insert the CN OLP Mode : constant current limiting with delay shutdown after seconds File Name:P-000PEC -09-

6 P-000CC P ss 000W ingle Output Power upply 6.hree Phase Connect FIG. A: W AC YEM (ANDAD MODEL FO OCK) L N L N L N N (NC) FIG. B: W /AC YEM L N L N N L N N W 90/0AC YEM 0 L N L N N (N.C.) L N N (NC) 90 FIG. C: File Name: P-000PEC -09-