GB FREQUENCY HVDC FREQUENCY RESPONSE PARAMTERS HVDC CONNECTIONS (TITLE II)

Transcription

1 GB FREQUENCY HVDC FREQUENCY RESPONSE PARAMTERS HVDC CONNECTIONS (TITLE II) HVDC Article 11 Range Requirement Range Suggested GB Value Comments Hz 60 seconds Hz 60 seconds Hz Hz than RfG and DCC and DC PPm s (ie 90 minutes plus) than RfG and DCC and DC PPm s (ie 90 minutes plus) Hz 100 minutes Hz 100 minutes Hz Unlimited Hz Unlimited Hz 51.5Hz - 52 than RfG and DCC and DC PPm s (ie 90 minutes plus) Hz 100 minutes 51.5Hz minutes Mandatory requirement s may be agreed Work group to s may be agreed Work group to GB s may be agreed Work group to Policy Req d? (e.g. ncompatibility to be defined) Change req d?

2 12 ROCOF -2.5 to +2.5Hz/s than DC PPm s (ie 15 minutes plus) Measured over the previous 1 second -2.5 to +2.5Hz/s Measured over the previous 1 second s may be agreed Work group to Mandatory requirement 13(1)(a)(i) 13(1)(a)(ii) 13(1)(a)(iii) Controlability and Power Step Size for Transmitting HVDC Active Power Transmission capacity for each direction below which active power transmission is not requested The maximum delay within which the Max Step Size = 1MW Min Step Size = 1MW to believed to be part of data submission as part of trading in wholesale market / TSOG? to MW transfer should be controllable to the nearest whole MW to MW transfer should be controllable to the nearest whole MW 2 minutes as per BC2

3 13(1)(b) 13(1)(c) 13(1)(d) HVDC System shall be capable of adjusting the transmitted active power upon receipt of request from the relevant TSO Capability of modifying transmitted infeed in case of disturbances into one or more AC networks Reversal Ability to modify transmitted active power for the purpose of cross boarder balancing t specified Covered by Fault Ride Through additional text to be added for HVDC and delays greater than 10ms Would be required only on a site specific basis and would be specified in the Bilateral Agreement. General Grid Mod to refer to the requirement and delay Covered by CC through the requirement to have a load controller and the Balancing s General words required in relation to Power Reversal?

4 13(2) Ramp Rate Limit adjustment 13(3) Automatic Remedial Action t specified Ramp Rate Limits covered under BC1.A.1.1 Adjustment of Ramp Rates below the limits of BC1.A.1.1 are permissible see BC1 Other than the current requirements under the Balancing s any other requirements would be specified under the Bilateral Agreement 14 Synthetic Inertia t required see FFCI requirements Option 1 15 FSM, LFSM-O, LFSM-U Annex II(A)(1) FSM Deadband 0 ±500mHz Deadband 0 RfG See Insensitivity Annex II(A)(1)(d) Droop S1(u) Droop S2(d) Insensitivity 0.1% 0.1% 30mHz 0.5 seconds DroopS1 (u) 3 5% DroopS2 (d) 3 5% for upward regulation Insensitivity 15mHz for Deadband 0.5 seconds RfG for non synchronous Only by reference to additional requirements being specified in the Bilateral Current Grid does not make this clear Introduce term insensitivity as per RfG

5 Annex II(B)(1) Annex II(c)(1) LFSM-O LFSM-U 16 Control delay t1 delay t1 plant set to 1s Time t2 30 seconds Time t2 10 seconds RfG and current Grid practice Threshold f1 Droop S3 0.1% upwards Initial Full Threshold f2 Droop S4 0.1% Initial Full Modulation of Active Power in relation to Hz Threshold f1 50.4Hz Droop S2 10% or less Initial Full <2s RfG 10s current RfG Hz Threshold f2 49.5Hz Droop S4 10% RfG upwards Initial <2s RfG Full Modulation of Active Power in relation to To be determined plant Dependent CC of Grid Discuss with Working Group Discuss with Working Group

6 17 Loss of Active Power Changes Changes Loss of 1800MW 37 Black Start Black Start Specified in Bilateral Agreement in the same way as Generation SQSS with and Bilateral Agreement