LCD Module + Touch Panel Specifications

Size: px

Start display at page:

Download "LCD Module + Touch Panel Specifications"

Claude Boone
5 years ago
Views:

1 LCD Module + Touch Panel Specifications Customer: Model Name: MRTP043R35A-006 Date: Version: V.0 Preliminary Specification Final Specification Customer Signature Approved By Comment Approved By Checked By Prepared By Carrio Carrio LXL 1

2 Record of Revision Version Revise Date Page Content Modified by V ALL First Issue LXL 2

3 Contents 1. General Description Electrical Characteristics Touch Panel Specifications Optical Characteristics Reliability Test Items General Precautions Mechanical Drawing Packing Standard

4 1. General Description 1.1 Introduction This specification applies to the 4.3 inch diagonal display module with touch panel. 1.2 Features 4.3 inch configuration Compatible with NTSC & PAL system Image Reversion: UP/DOWN and LEFT/RIGHT Resistive Touch panel ROHS design 1.3 General information Feature SPEC Display Spec Pixel pitch(mm) 0.198(H) x 0.198(V) Display Mode TN, Normally white Surface Treatment Anti-glare Mechanical Electrical Characteristics RTP Siza Resolution Technology Type Pixel Configuration Viewing Direction Gray Scale Inversion Direction OD(W*H*D)(mm) Active Area With/Without TP Matching Connection Type LED Numbers 6 O clock 12 O clock (H) x 62.7(V) x 4.1(D) With TP N/A 10 LED Weight(g) (g) Interface 24 bits RGB Color Depth 16.7M Driver IC Connector Hardness Structure Input Method Active Area(mm) 4.3 inch 480(H) x 3RGB x 272(V) a-si TFT R.G.B.Vertical Stripe 95.04(H) x 53.86(V) 0TA5180A FPC 3H F/G Stylus or Finger 97.00(H) x 55.5(V) 4

5 Number of simultaneous touches 1 Linearity 1.5% Stylus(mm) 0.8 5

6 2. Electrical Characteristics 2.1 Interface Pin connection No. Symbol Description 1 VSS Gound 2 VSS Gound 3 VDD Power Supply 4 VDD Power Supply 5 R0 Red Data Bit 0 6 R1 Red Data Bit 1 7 R2 Red Data Bit 2 8 R3 Red Data Bit 3 9 R4 Red Data Bit4 10 R5 Red Data Bit 5 11 R6 Red Data Bit 6 12 R7 Red Data Bit 7 13 G0 Green Data Bit 0 14 G1 Green Data Bit 1 15 G2 Green Data Bit 2 16 G3 Green Data Bit 3 17 G4 Green Data Bit 4 18 G5 Green Data Bit 5 19 G6 Green Data Bit 6 20 G7 Green Data Bit 7 21 B0 Blue Data Bit 0 22 B1 Blue Data Bit 1 23 B2 Blue Data Bit 2 24 B3 Blue Data Bit 3 25 B4 Blue Data Bit 4 26 B5 Blue Data Bit 5 27 B6 Blue Data Bit 6 28 B7 Blue Data Bit 7 29 VSS Ground 30 PCLK Dot Data Clock 31 PON Standby mode. PON = 1 : Normally operation. PON = 0 : Standby mode. 32 HSYNC Horizotal Sync Input 33 VSYNC Vertical Sync Input 6

7 34 NC Data input enable. If unused, please pull low level. 35 NC Not Connection 36 VSS Gound 37 XR Touch horizontal Pin 38 YD Touch vertical Pin 39 XL Touch horizontal Pin 40 YU Touch vertical Pin 41 VSS Ground 42 LED Back light cathode 43 LED+ Back light anode 44 NC No connection 45 NC No connection 2.2 Block diagram 7

8 2.3 Backlight characteristics Backlight specification Item Symbol Condition Min Typ Max Unit Forward Voltage Vf Ta=25,If=40mA V Forward Current If Ta= ma Uniformity Avg 75 - % Reverse Current Ir 20 ua Power dissipation Pd W Drive method Constant current 40mA LED configuration 10EDs (5LEDs in series and 2 branches in parallel) Backlight Unit Item Symbol Min Max Unit CONDITION Note LED Voltage Vf V Ta=25 1 LED Current If Ma Ta=25 1 Life Time 30K 50K Hr Ta=25 2 Note 1:LED supply voltage defined by an array of 2 branches of 5 diodes in series. Note 2:Useful Life is defined as the time for the emitted luminance of the backlight to decline to 50% of its initial brightness. Stresses above those listed under "Absolute Maximum Rating" may cause permanent damage to the device. 8

9 2.4 Electrical and mechanical characteristics TFT LCD DC Characteristics Item Symbol Min Typ Max Unlt Supply Voltage VDD V IO Supply Voltage VDDI VDD V. Charge Supply Voltage PVDD V NVM Supply Voltage VPP V Input Voltage VCI V Conditlons Item Symbol Min Typ Max Unlt Positive High-voltage power VGH V Negative High-voltage power. Output Voltage Deviation Standby Current Operation Current VGL Vod Isc V mv ua Ioc 15 ma Conditlons PVDD=3.3V PVDD=3.3V VDD=PVDD= 3.3V No Load VDD=VDDI= 9

10 2.4.2 TFT LCD AC Characteristics Item Symbol Min Typ Max Unlt System operation timing VDD power source slew time TPOR ms GRB pulse width RSTW us Input/ Output timing Conditlons From 0V to 99% VDD R=10Kohm, C=1uF CLK pulse duty Hsync width Hsync period Vsync setup time Vsync hold time Hsync setup time Hsync hold time Data setup time Data hold time SD output stable time GD output rise and fall time Tcw % Thw DCLK Th us Tvst us Tvhd us Thst us Thhd us Tdsu us Tdhd us Tst us Tgst us Output settled within +20mV Loading= 6.8k+28.2pF. Output settled (5%-95%), Loading= 4.7k+29.8pF 10

11 2.5 Data Transmission Timing in parallel RGB(24bit) Interface Clock and Data input Timing Diagram wire Commuication Timing Diagram Parallel RGB Input Timing Table Item Symbol Min Typ Max Unlt DCLK Frequency Fclk MHz DCLK Period Tclk ns Period Time Th DCLK Display Period Thdisp 480 DCLK HSYNC Back porch Thbp DCLK Front Porch Thfp DCLK Pulse Width Thw DCLK Period Time Tv H Display period Tvdisp 272 H HSYNC Back Porch Tvbp H Front Porch Tvfp H Pulse Width Tvw H Remark 11

12 2.5.4 SYNC Mode Timing Diagram SYNC-DE Mode Timing Diagram 12

13 2.6 Power Sequence Power-On Sequence Power Off Sequence 13

14 3. Touch Panel Specifications 3.1 Features Item Specifications (1) Product Structure F/G (2) ITO Glass 0.7 mm (3) ITO Film mm (4) Input Mode Stylus or Finger (5) Connector FPC (4-wire) 3.2 Optical Characteristics Item Specifications (1) Transparency 78%-550nm 3.3 Electrical Characteristics (1) Item Terminal resistance Specifications Rx-x: Ω R y-y: Ω (2) Linearity 1.5 (3) Chattering 20ms (4) Insulation 20M Ω /25V (DC) 3.4 Mechanical Characteristics Item Specification Condition (1) Operating Force Stylus=R0.8 Range at 50g 115g (2) Hardness 3H pencil, pressure 1N/45 3H 14

15 4. Optical Characteristics Item Symbol condition Min Typ Max Unit Note Luminous intensity LV cd/ m2 1,4 Contrast CR ,2 Response time Tr+Tf msec 1,3 NTSC % White Wx Wy Color chromaticity (CIE1931) Red Green Blue Rx Ry Gx Gy Bx By θ=0 Normal viewing angle ,4 Viewing angle Hor Ver ΘL ΘR CR>10 ΘU ΘD Luminance Uniformity YU θ= % 5 View Direction 6 o'clock(max.contrast Gray level inversion) 6 15

16 4.1 Measuring Condition Measuring surrounding : dark room Ambient temperature : 25±2 30min. warm-up time. 4.2 Measuring Equipment TOPCON BM-5A Measuring spot size : field 2 Note 1: Definition of viewing angle range Fig. 4-1 Definition of viewing angle Note 2: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 30 minutes operation, the optical properties are measured at the center point of the LCD screen. (Response time is measured by Photo detector TOPCON BM-7, other items are measured by BM-5A/Field of view: 1 /Height: 50cm.) 16

17 1 Fig. 4-2 Optical measurement system setup Note 3: Definition of Response time The output signals of photo detector are measured when the input signals are changed from black to white (rising time) and from white to black (falling time), respectively. The response time is defined as the time interval between the 10% and 90% of amplitudes. Refer to figure as below Fig. 4-3 Definition of response time 17

18 Note 4: Definition of contrast ratio: Contrast ratio (CR)= Luminance measured when LCD on the "White" state Luminance measured when LCD on the "Black" state Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel. The LED driving condition is IL=40mA. Note 7: Definition of Luminance Uniformity Active area is divided into 9 measuring areas Refer to Fig.4-4. Every measuring point is placed at the center of each measuring area. Luminance Uniformity (Yu)= Bmin Bmax Bmin: The measured minimum luminance of all measurement position. Bmax: The measured maximum luminance of all measurement position. L Active area length W----- Active area width L L/6 L/3 L/3 W/ W/3 W W/ Fig. 4-4 Definition of measuring points 18

19 5. Reliability Test Items NO. Test Item Test Conditions Remark 1 High Temperature Storage Ta = hrs Note 1,Note 4 2 Low Temperature Storage Ta = hrs Note 1,Note 4 3 High Temperature Operation Ts = hrs Note 2,Note 4 4 Low Temperature Operation Ta = hrs Note 1,Note 4 5 Operate at High Temperature and Humidity +60, 90%RH 240hrs Note 4 6 Thermal Shock -20 /30 min ~ +60 /30 min for a total 200 cycles, Start with cold temperature and end NON- Operation with high temperature. 7 Mechanical Shock 100G 6ms,±X, ±Y, ±Z 3 times for each direction NON- Operation 8 Package Vibration Test Random Vibration : 0.015G*G/Hz from 5-200HZ, -6dB/Octave from HZ 2 hours for each direction of X. Y. Z. (8 hours for total) NON- Operation Note1:Condition of image Sticking test:25 ±2 Operation with test pattem sustained for 4 hrs,then change to gray pattern immediately. After 5 mins, the mura be disappeared completely. (a)test Pattern(chess board Pattern) (b)gray Pattern Note 2: Ta is the ambient temperature of samples. Note 3: Ts is the temperature of panel s surface. Note 4: In the standard condition, there shall be no practical problem that may affect the display function. After the reliability test, the product only guarantees operation,but don t guarantee all of the cosmetic specification. Note 5: Before cosmetic and function test, the product must have enough recovery time,at least 2 hours at room temperature. 19

20 Electrostatic Discharge TEST ITEM CONFITIONS NOTE ESD Note: Measure point: 1. LCD glass and metal bezel 2. IF connector pins 150Pf,330Ω 8kV&±15kV air& contact test 1 200Pf,0Ω,±200V contact test 2 20

21 6. General Precautions 6.1 Safety Liquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your skin or clothes, wash it off immediately by using soap and water. 6.2 Handling (1). The LCD panel is plate glass. Do not subject the panel to mechanical shock or to excessive force on its surface. (2). The polarizer attached to the display is easily damaged. Please handle it carefully to avoid scratch or other damages. (3). To avoid contamination on the display surface, do not touch the module surface with bare hands. (4). Keep a space so that the LCD panels do not touch other components. (5). Put cover board such as acrylic board on the surface of LCD panel to protect panel from damages. (6). Transparent electrodes may be disconnected if you use the LCD panel under environmental conditions where the condensation of dew occurs. (7). Do not leave module in direct sunlight to avoid malfunction of the ICs. 6.3 Static Electricity (1). Be sure to ground module before turning on power or operating module. (2). Do not apply voltage which exceeds the absolute maximum rating value. 6.4 Storage (1). Store the module in a dark room where must keep at 25±10 and 65%RH or less. (2). Do not store the module in surroundings containing organic solvent or corrosive gas. (3). Store the module in an anti-electrostatic container or bag. 6.5 Cleaning (1). Do not wipe the polarizer with dry cloth. It might cause scratch. (2). only use a soft cloth with IPA to wipe the polarizer, other chemicals might permanent damage to the polarizer. 21

22 7. Mechanical Drawing Pin SYNBOLS 1 VSS VSS VDD VDD R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7 VSS PCLK LB B BL xxxxxx 20.1± ± PON HSYNC VSYNC DE NC VSS XR YD XL YU VSS LED- LED+ NC ± ±0.03 Pin OUT 0.3± ± ± ±0.10 TEL (0755) FAX (0755) N/A LM Size LCM+RTP Module Description MRTP043R35A-006 Name N/A Unit mm 1:1 Mothed N/A Versions V0 4.1±0.3 (RTP+LCM) 1.1±0.1 (RTP) 3±0.2 (LCM) 0.3± ± ± A Authorizer Date Proofread Designed Plot Surface treatment Date Date Texture Stock size processing sequence heat treating Proportion Quantity Outsourcing processing Carrio LXL Date N/A are no NC 105.5±0.2 (LCM OD) 104.7±0.2 (RTP OD) (RTP V.A) (LCD A.A) 480X3(RGB)X (LCD A.A) (RTP V.A) 64.9±0.2 (RTP OD) 67.2±0.2 (LCM OD) Determination condition Unit max typ min Symbol Item V VF Forward Voltage ma IF Forward Current If= 40 ma cd/m Lv Brightness(LCM+RTP) (Constant current) X Chroma Coordinate Y % 75 Uniformity Operation Topr -20 C TO 70 C Temperature Storage Tsto -30 C TO 80 C Temperature A Third place Tolorence size tolorence ±0.05 0~10.00 ± ~50.00 ± ~80.00 ± ~ Change content Modificator Date 22

L495*W342*H185mm, and the pallet is L1200*W1000*H150mm.

23 8. Packing Standard Step1 Step2 Step4 6PCS Product 1Tray 72 PCS Product 1PE bag Step3 EPE Protect Sheet PE Bag Package EPE Protect Sheet Outer Box 90PCS Product 1 Outer Box Outer Box Step5 The carton size is L495*W342*H185mm, and the pallet is L1200*W1000*H150mm. Each pallet packs 25 cartons (5layers) and each layer is including 5 cartons. The size of packed pallet is L1200*W1000*H1075mm, There are 72pcs in a carton. 23

CHIMEI INNOLUX DISPLAY CORPORATION LCD MODULE SPECIFICATION

CHIMEI INNOLUX DISPLAY CORPORATION LCD MODULE SPECIFICATION DISPLAY CORPORATION LCD MODULE SPECIFICATION Customer: Model Name: EJ101IA-01F Date: 2012/01/03 Version: 01 Preliminary Specification Final Specification For Customer s Acceptance Approved by Comment Approved