Datasheet G156HCE-E01. Cover Lens. Bezel Touch Sensor. Bonding/Optical/Tape. Embedded Board/ AD Driving solution. TFT display

Size: px

Start display at page:

Download "Datasheet G156HCE-E01. Cover Lens. Bezel Touch Sensor. Bonding/Optical/Tape. Embedded Board/ AD Driving solution. TFT display"

Chester Sullivan
5 years ago
Views:

Cover Lens Bezel Touch Sensor Embedded Board/ AD Driving

TFT display Backlight Driver Housing Computer-on-Module

If you require a touch panel and/or mechanical

1 Cover Lens Bezel Touch Sensor Embedded Board/ AD Driving solution Storage Wireless Software Bonding/Optical/Tape TFT display Backlight Driver Housing Computer-on-Module Memory More Value! If you require a touch panel and/or mechanical integration, please scan the QR code or click the URL /products/displays/colour-tft-displays/ Datasheet G56HCE-E

2 Doc. Number Tentative Specification Preliminary Specification Approval Specification MODEL NO. G56HCE SUFFIX E Customer APPROVED BY SIGNATURE Name / Title Note Please return copy for your confirmation with your signature and comments. Approved By Checked By Prepared By Version. 7 January 27 / 26 The

3 CONTENTS. GENERAL DESCRIPTION...5. OVERVIEW GENERAL SPECIFICATIONS MECHANICAL SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS ABSOLUTE RATINGS OF ENVIRONMENT ELECTRICAL ABSOLUTE RATINGS TFT LCD MODULE BACKLIGHT CONVERTER ELECTRICAL SPECIFICATIONS FUNCTION BLOCK DIAGRAM INTERFACE CONNECTIONS ELECTRICAL CHARACTERISTICS LCD ELETRONICS SPECIFICATION Vcc Power Dip Condition... 錯誤! 尚未定義書籤 BACKLIGHT UNIT BACKLIGHT PIN ASSIGNMENT LVDS INPUT SIGNAL SPECIFICATIONS LVDS DATA MAPPING TABLE... 錯誤! 尚未定義書籤 COLOR DATA INPUT ASSIGNMENT DISPLAY TIMING SPECIFICATIONS POWER ON/OFF SEQUENCE OPTICAL CHARACTERISTICS TEST CONDITIONS OPTICAL SPECIFICATIONS RELIABILITY TEST ITEM PACKING MODULE LABEL PRECAUTIONS ASSEMBLY AND HANDLING PRECAUTIONS STORAGE PRECAUTIONS OPERATION PRECAUTIONS SAFETY PRECAUTIONS SAFETY STANDARDS OTHER...25 Version. 7 January 27 2 / 26 The

4 . Outline Drawing...26 Version. 7 January 27 3 / 26 The

5 REVISION HISTORY Version Date Page Description. Jan.6, 27 All Spec Ver.. was first issued. Version. 7 January 27 4 / 26 The

6 . GENERAL DESCRIPTION. OVERVIEW G56HCE-E is a 5.6 TFT Liquid Crystal Display module with LED Backlight unit and 4 pins edp interface. This module supports 92 x 8 FHD AAS mode and can display 262,44 colors. The LED driving device for Backlight is built in PCBA..2 GENERAL SPECIFICATIONS Item Specification Unit Note Screen Size 5.6 real diagonal Driver Element a-si TFT active matrix - - Pixel Number 92 x R.G.B. x 8 pixel - Pixel Pitch.7925 (H) x.7925 (V) mm - Pixel Arrangement RGB vertical stripe - - Display Colors 6.7M color - Transmissive Mode Normally Black - - Surface Treatment Hard coating (3H), Anti-Glare - - Luminance, White 45 Cd/m2 Color Gamut 72 % of NTSC(Typ.) - - Power Consumption 2. W Max 2. MECHANICAL SPECIFICATIONS Item Min. Typ. Max. Unit Note Horizontal (H) mm Module Size Vertical (V) mm Thickness (T) mm Bezel Area Horizontal mm Vertical mm Active Area Horizontal mm Vertical mm Weight - 35 g Version. 7 January 27 5 / 26 The

7 3. ABSOLUTE MAXIMUM RATINGS 3. ABSOLUTE RATINGS OF ENVIRONMENT Item Symbol Value Min. Max. Unit Note Storage Temperature TST -2 6 () Operating Ambient Temperature TOP 5 (), (2) Note () (a) 9 %RH Max. (Ta < 4 ). (b) Wet-bulb temperature should be 39 Max. (Ta < 4 ). (c) No condensation. Note (2) The temperature of panel surface should be min. and 6 max. 3.2 ELECTRICAL ABSOLUTE RATINGS 3.2. TFT LCD MODULE Item Symbol Min. Value Max. Power Supply Voltage Vcc V Logic Input Voltage V IN -.3 VCCS+.3 V Note () Stresses beyond those listed in above ELECTRICAL ABSOLUTE RATINGS may cause permanent damage to the device. Normal operation should be restricted to the conditions described in ELECTRICAL CHARACTERISTICS BACKLIGHT CONVERTER Item Symbol Value Min. Typ Max. Unit Converter Voltage LED_V in 2 8 V Enable Voltage LED_EN V Backlight Adjust LED_PWM V Unit Note Note () (), (2) Duty=% (), (2) Pulse Width msec. and Duty % Note () Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2) Specified values are for input pin of LED light bar at Ta=25±2 (Refer to and for further information). Version. 7 January 27 6 / 26 The

8 4. ELECTRICAL SPECIFICATIONS 4. FUNCTION BLOCK DIAGRAM RX(+/-) RX(+/-) RX2(+/-) RX3(+/-) RXC(+/-) NC GND Vcc CONVERTER CONNECTOR CONVERTER Version. 7 January 27 7 / 26 The

9 4.2. INTERFACE CONNECTIONS PIN ASSIGNMENT Pin Name Description NC Reverse for INNOLUX test only. 2 H_GND High Speed Ground. 3 Lane_N Comp Signal Lane. 4 Lane_P True Signal Link Lane. 5 H_GND High Speed Ground. 6 Lane_N Comp Signal Lane. 7 Lane_P True Signal Link Lane. 8 H_GND High Speed Ground. 9 AUX_CH_P True Signal Auxiliary Ch. AUX_CH_N Comp Signal Auxiliary Ch H_GND High Speed Ground. 2 LCD_Vcc LCD logic and Driver power 3 LCD_Vcc LCD logic and Driver power 4 LCD_Self_Test or NC LCD Panel Self Test Enable(Optional) 5 LCD_GND LCD logic and Driver ground 6 LCD_GND LCD logic and Driver ground 7 HPD- HPD Signal pin 8 BL_GND Backlight_ ground 9 BL_GND Backlight_ ground 2 BL_GND Backlight_ ground 2 BL_GND Backlight_ ground 22 BL_Enable Backlight ON / OFF 23 BL PWM DIM System PWM Signal Input 24 NC Reverse for INNOLUX test only. 25 NC Reverse for INNOLUX test only. 26 BL PWR Backlight Power (5V~2V) 27 BL PWR Backlight Power (5V~2V) 28 BL PWR Backlight Power (5V~2V) 29 BL PWR Backlight Power (5V~2V) 3 NC No Connect (Reserved for CM) 3 NC No Connect (Reserved) 32 NC No Connect (Reserved) 33 NC No Connect (Reserved) 34 NC No Connect (Reserved) 35 NC No Connect (Reserved) 36 NC No Connect (Reserved) 37 NC No Connect (Reserved) 38 NC No Connect (Reserved) 39 NC No Connect (Reserved) 4 NC No Connect (Reserved) Note () Connector Part No. xxxxxxx Note (2) The first pixel is odd. Note (3) Input signal of even and odd clock should be the same timing. Version. 7 January 27 8 / 26 The

10 4.3 ELECTRICAL CHARACTERISTICS 4.3. LCD ELETRONICS SPECIFICATION Parameter Symbol Value Min. Typ. Max. Unit Note Power Supply Voltage Vcc V () Ripple Voltage V RP - 5- mv () Rush Current I RUSH A (),(2) Power Supply Current Mosaic ma (3)a Black ma (3) HPD High Level V (5) Low Level.4 V (5) HPD Impedance RHPD 3K ohm (5) Note () The ambient temperature is Ta = 25 ± 2 ºC. Note (2) IRUSH the maximum current when VCCS is rising IIS the maximum current of the first ms after power-on Measurement Conditions Shown as the following figure. Test pattern black. Version. 7 January 27 9 / 26 The

Note (3) The specified power supply current is under the conditions at VCCS = 3.3 V, Ta = 25 ± 2 ºC, DC Current and fv = 6 Hz, whereas a power dissipation check pattern below is displayed. a. Mosaic Pattern Note (4) The specified signals have equivalent impedances pull down to ground in the LCD module respectively.

11 Note (3) The specified power supply current is under the conditions at VCCS = 3.3 V, Ta = 25 ± 2 ºC, DC Current and fv = 6 Hz, whereas a power dissipation check pattern below is displayed. a. Mosaic Pattern Note (4) The specified signals have equivalent impedances pull down to ground in the LCD module respectively. Customers should keep the input signal level requirement with the load of LCD module. Please refer to Note (4) of LED CONVERTER SPECIFICATION to obtain more information. Note (5) When a source detects a low-going HPD pulse, it must be regarded as a HPD event. Thus, the source must read the link / sink status field or receiver capability field of the DPCD and take corrective action. Version. 7 January 27 / 26 The

12 4.3.2 BACKLIGHT UNIT Value Parameter Symbol Unit Min. Typ. Max. Converter Power Supply Voltage LED_Vin V Converter Power Supply Current Ii.8..2 A Power Consumption P LED.5 W EN Control Level PWM Control Level Backlight on LED_EN Backlight off.8 PWM High Level LED_PWM PWM Low Level.5 PWM Control Duty Ratio -- % PWM Control Frequency f PWM 9 2 2k Hz V V 2V LED_Vin = 2V Duty=% LED Life Time L L 5, Hrs (2) Note () LED light bar input voltage and current are measured by utilizing a true RMS multimeter as shown below Note (2) The lifetime of LED is defined as the time when LED packages continue to operate under the conditions at Ta = 25 ±2 and I= 7 ma (per chip) until the brightness becomes 5% of its original value. Input Power PLED Power Supply Vin, Ii GND Converter LED Backlight Unit Version. 7 January 27 / 26 The

13 Version. 7 January 27 2 / 26 The BACKLIGHT PIN ASSIGNMENT Pin Symbol Description Remark V i Converter input voltage 2V 2 V GND Converter ground Ground 3 EN Enable pin 3.3 V 4 ADJ Backlight Adjust PWM Dimming (Hi 3.3 V DC, Lo V DC ) 5 NC Not Connect Note () Connector Part No. 4.4 LVDS INPUT SIGNAL SPECIFICATIONS 4.4. COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Data Signal Red Green Blue Color R7 R6 R5 R4 R3 R2 R R G7 G6 G5 G4 G3 G2 G G B7 B6 B5 B4 B3 B2 B B Basic Colors Black Red Green Blue Cyan Magenta Yellow White Gray Scale Of Red Red() / Dark Red() Red(2) Red(253) Red(254) Red(255) Gray Scale Of Green Green() / Dark Green() Green(2) Green(253) Green(254) Green(255) Gray Scale Of Blue Blue() / Dark Blue() Blue(2) Blue(253) Blue(254) Blue(255)

14 Note () Low Level Voltage, High Level Voltage Version. 7 January 27 3 / 26 The

15 4.5 DISPLAY TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Signal Item Symbol Min. Typ. Max. Unit Note Frequency Fc MHz - Period Tc 3.5 ns Input cycle to cycle jitter T rcl -.2*Tc.2*Tc ns (3) Input Clock TLVCCS -.2*Tc.2*Tc ns (4) LVDS Clock Vertical Display Term Horizontal Display Term to data skew Spread spectrum modulation range Spread spectrum modulation frequency Fclkin_ mod FC*98% FC*2% MHz F SSM 2 KHz Frame Rate Fr Hz Tv=Tvd+Tvb Total Tv Th - Active Tvd Th - Display Blank Tvb Th - Total Th Tc Th=Thd+Thb Active Display Thd Tc - Blank Thb Tc - Note () Because this module is operated by DE only mode, Hsync and Vsync input signals are ignored. Note (2) The Tv(Tvd+Tvb) must be integer, otherwise, this module would operate abnormally. (5) INPUT SIGNAL TIMING DIAGRAM Version. 7 January 27 4 / 26 The

16 4.6 POWER ON/OFF SEQUENCE Timing Specifications Parameter Value Min Typ Max Units T.5 - ms T2-5 ms T3-5 ms T ms T ms T ms T7 5-3 ms T8 - - ms T9 - - ms T ms Note () Please avoid floating state of interface signal at invalid period. Note (2) When the interface signal is invalid, be sure to pull down the power supply of LCD VCC to V. Version. 7 January 27 5 / 26 The

17 Note (3) The Backlight converter power must be turned on after the power supply for the logic and the interface signal is valid. The Backlight converter power must be turned off before the power supply for the logic and the interface signal is invalid. Version. 7 January 27 6 / 26 The

18 5. OPTICAL CHARACTERISTICS 5. TEST CONDITIONS Item Value Unit Ambient Temperature (Ta) 25±2 Ambient Humidity (Ha) 5± %RH Supply Voltage Input Signal LED Light Bar Input Current Per Input Pin o C According to typical value in "ELECTRICAL CHARACTERISTICS" 5.2 OPTICAL SPECIFICATIONS The relative measurement methods of optical characteristics are shown in 5.2 and all items are measured at the center point of screen except white variation. The following items should be measured under the test conditions described in 5. and stable environment shown in Note (5). Color Chromaticity (CIE 93) Item Symbol Condition Min. Typ. Max. Unit Note Rx.627 Red Ry.339 Green Blue White Center Luminance of White (Center of Screen) Contrast Ratio Gx.328 Gy Typ.59 Bx θ x =, θ Y =.45.6 CS-2 By.63 R=G=B=255 Wx Gray scale.33 Wy.329 Typ (), (5) L C cd/m 2 (4), (5) CR (2), (5) T R Response Time θ T x =, θ Y = ms (3) F White Variation W θ x =, θ Y = % (5), (6) Horizontal θx- + θx Viewing Angle CR Deg. (), (5) Vertical θy- + θy Version. 7 January 27 7 / 26 The

19 Note () Definition of Viewing Angle (θx, θy) Note (2) Definition of Contrast Ratio (CR) The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L255 / L L255 Luminance of gray level 255 L Luminance of gray level CR = CR (5) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6). Note (3) Definition of Response Time (T R, T F ) Version. 7 January 27 8 / 26 The

20 Note (4) Definition of Luminance of White (L C ) Measure the luminance of gray level 255 at center point L C = L (5) L (x) is corresponding to the luminance of the point X at Figure in Note (6). Note (5) Measurement Setup The LCD module should be stabilized at given temperature for 4 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 4 minutes in a windless room. Note (6) Definition of White Variation (δw) Measure the luminance of gray level 255 at 9 points δw = ( Minimum [L () ~ L (9)] / Maximum [L () ~ L (9)] ) *% Version. 7 January 27 9 / 26 The

21 6. RELIABILITY TEST ITEM Items Required Condition Note High Temperature Storage 5, 24hours ()(2) Low Temperature Storage -2, 24hours ()(2) Thermal Shock Test -2 /3min, 5 / 3min, cycles ()(2) High Temperature Operation 5, 24hours ()(2) Low Temperature Operation, 24hours ()(2) High Temperature & High Humidity Operation Test Vibration Test (Non-operation) Shock Test (Non-operation) ESD (Electro Static Discharge) 5, RH 9%, 24 hours ()(2) Acceleration.5 Grms (3) Wave Half-sine Frequency - 3 Hz Sweep 3 Minutes each Axis (X, Y, Z) Acceleration 5 G (3) Wave Half-sine Active Time ms Direction ± X, ± Y, ± Z.(one time for each Axis) Contact Discharge ± 8KV, 5pF(33Ω) () Air Discharge ± 5KV, 5pF(33Ω) () Note () criteria Normal display image with no obvious non-uniformity and no line defect. Note (2) Evaluation should be tested after storage at room temperature for more than two hour Note (3) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. The fixing condition is shown as below Version. 7 January 27 2 / 26 The

22 7. PACKING 7. PACKING SPECIFICATIONS () 3 pcs LCD modules / Box (2) Box dimensions 465 (L) X 362 (W) X 34 (H) mm (3) Weight approximately 2Kg (3 modules per box) 7.2 PACKING METHOD Figure. 7- Packing Version. 7 January 27 2 / 26 The

23 Sea / Land Transportation (4ft Container) Air Transportation Figure. 7-2 Packing 7.3 UN-PACKING METHOD Figure. 7-3 UN-Packing Version. 7 January / 26 The

24 8. MODULE LABEL. INX MODULE LABEL The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation. G56HCE-E E27943 XXXXXXXYMDXNNNN **** RoHS (a) Model Name G56HCE-E (b) Revision Rev. XX, for example A, B, C, C2 etc. (c) **** Factory ID (d) Serial ID X X X X X X X Y M D X N N N N Serial INX Internal Use Year, Month, Date INX Internal Use Revision INX Internal Use Serial ID includes the information as below (a) Manufactured Date Year ~9, for 2~29 Month ~9, A~C, for Jan. ~ Dec. Day ~9, A~Y, for st to 3 st, exclude I, O and U (b) Revision Code cover all the change (c) Serial No. Manufacturing sequence of product Version. 7 January / 26 The

25 9. PRECAUTIONS 9. ASSEMBLY AND HANDLING PRECAUTIONS () Do not apply rough force such as bending or twisting to the module during assembly. (2) To assemble or install module into user s system can be only in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (3) It s not permitted to have pressure or impulse on the module because the LCD panel and Backlight will be damaged. (4) Always follow the correct power sequence when LCD module is connecting and operating. This can prevent damage to the CMOS LSI chips during latch-up. (5) Do not pull the I/F connector in or out while the module is operating. (6) Do not disassemble the module. (7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. (8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage LCD module when it is operating. (9) High temperature or humidity may reduce the performance of module. Please store LCD module within the specified storage conditions. ()When ambient temperature is lower than may reduce the display quality. For example, the response time will become slowly. 9.2 STORAGE PRECAUTIONS () Do not leave the module in high temperature, and high humidity for a long time. It is highly recommended to store the module with temperature from to 35 and relative humidity of less than 7% (2) Do not store the TFT LCD module in direct sunlight (3) The module should be stored in dark place. It is prohibited to apply sunlight or fluorescent light in storing 9.3 OPERATION PRECAUTIONS () The LCD product should be operated under normal condition. Normal condition is defined as below Temperature 2±5 Humidity 65±2% Display pattern continually changing pattern(not stationary) (2) If the product will be used in extreme conditions such as high temperature,high humidity,high altitude,display pattern or operation time etc It is strongly recommended to contact INNOLUX for application engineering advice. Otherwise, Its reliability and function may not be guaranteed. 9.4 SAFETY PRECAUTIONS () If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. (2) After the module s end of life, it is not harmful in case of normal operation and storage. Version. 7 January / 26 The

26 9.5 SAFETY STANDARDS The LCD module should be certified with safety regulations as follows () UL695- or updated standard. (2) IEC695- or updated standard. 9.6 OTHER When fixed patterns are displayed for a long time, remnant image is likely to occur. Version. 7 January / 26 The

27 . Outline Drawing Version. 7 January / 26 The

28 Offices DACH (Germany, Austria, Switzerland) Avnet EMG GmbH Gruber Straße 6d Poing Phone Denmark Avnet Integrated Solutions Avnet Nortec A/S Lyskær Herlev Phone Fax denmark_integrated@avnet.eu Finland Avnet Integrated Solutions Avnet Nortec Oy Pihatörmä B 224 Espoo Phone Fax finland_integrated@avnet.eu France Avnet Integrated Solutions Avnet EMG France SA Parc Club du Moulin à Vent, Bât 33, rue du Dr Georges Lévy Vénissieux Cedex Phone Fax lyon_integrated@avnet.eu Avnet Integrated Solutions Avnet EMG France SA 4 avenue Carnot 9349 Massy Cedex Phone Fax paris_integrated@avnet.eu Avnet Integrated Solutions Avnet EMG France SA Les Peupliers II 35 avenue des Peupliers 355 Cesson-Sévigné Phone Fax rennes_integrated@avnet.eu Israel Avnet Israel st Avnet Road 465 Tel Mond Phone daniel.katz@avnet.eu Italy Avnet Integrated Solutions Avnet EMG Italy SRL Via Manzoni, Cusano Milanino Phone Fax milano_integrated@avnet.eu South Africa Avnet South Africa (Johannesburg) Block 3, Pinewood Office Park, 33 Riley Road, Woodmead P.O. Box 3853, Rivonia, 228, South Africa Phone Fax sales@avnet.co.za Avnet South Africa (Cape Town) Ground Floor, Forrest House, Belmont Office Park, 4 Belmont Road, Rondebosch P.O. Box 34, Mowbray, 775, South Africa Phone Fax sales@avnet.co.za Avnet South Africa (Durban) 22 Clemsford, 2 nd, Essex Gardens, Nelson Road, Westville P.O. Box 428, Wandsbeck, 363, South Africa Phone Fax sales@avnet.co.za Sweden (Norway) Avnet Integrated Solutions Avnet Nortec AB Löfströms Allé Sundbyberg Phone Fax sweden_integrated@avnet.eu United Kingdom (Ireland) Avnet Integrated Solutions 5a Waltham Park White Waltham Maidenhead Berkshire, SL6 3TN Phone Fax uk_integrated@avnet.eu All trademarks and logos are the property of their respective owners. This document provides a brief overview only, no binding offers are intended. No guarantee as to the accuracy or completeness of any information. All information is subject to change, modifications and amendments without notice. 6/27

MODEL NO.: G156BGE SUFFIX: L03

MODEL NO.: G156BGE SUFFIX: L03 Doc. Number Tentative Specification Preliminary Specification Approval Specification MODEL NO. G56BGE SUFFIX L3 Customer APPROVED BY SIGNATURE Name / Title Note Please return copy for your confirmation