PERFORMER SERIES FOLLOWSPOT OPERATION MANUAL

Transcription

1 REGISTER THIS PRODUCT WITH SELECON: PERFORMER SERIES FOLLOWSPOT OPERATION MANUAL Toru 4-8 Narrow Angle Followspot Thank you for purchasing a Selecon Performer Series Followspot luminaire. We have designed this luminaire to provide you with a superior fitting in performance, design and engineering. We are confident that it will perform to your expectations for many years to come. CAUTION! READ THIS MANUAL FROM COVER TO COVER BEFORE ATTEMPTING INSTALLATION. Installation is entirely at your risk. Do not attempt installation unless you are suitably qualified. If you do not understand a point in this manual, don t guess. Don t take short cuts. If in doubt, stop! Contact Selecon or one of its authorised distributors for advice. Don t be afraid to ask for help.

2 Performer Operation Manual 2 Important! Read this manual from cover to cover before attempting to install, operate or maintain the luminaires to which it relates. The manual contains important installation, operating, maintenance and safety procedures. The customer must strictly comply with them. Along with such procedures mentioned in this document, the customer should also observe such other procedures generally applicable to lighting equipment. Follow the instructions in this manual carefully. Selecon accepts no responsibility if the customer fails to do so. For each customer, operating conditions will vary, sometimes greatly. Such variations may affect the luminaires performance. Selecon has no control over the customer s unique operating environment. Hence, Selecon makes no representations or warranties concerning the luminaires performance under the customer s actual operating conditions. All operating parameters must be validated for each customer application by the customer s technical experts. If the customer does not follow the installation, operating, maintenance and safety procedures in this manual, as well as those generally applicable to lighting equipment, the luminaire may not perform as expected. More seriously, it may cause property damage, personal injury or other losses. Selecon accepts no liability for direct, indirect, incidental, special, or consequential damages resulting from the customer s failure to follow the installation, operating, maintenance and safety procedures in this manual or those generally applicable to lighting equipment. The foregoing limitation extends to damages for personal injury, property damage, loss of operations, loss of profits, loss of product or loss of time, whether incurred by the customer, the customer s employees or a third party. Selecon used all due care in preparing this manual. However, Selecon accepts no liability for errors or omissions. Selecon reserves the right to change the specifications of its luminaires, or the information in this manual, without necessarily giving its customers notice thereof. Installation, operation and maintenance are entirely at the customer s risk. Selecon s luminaires should be installed, operated and maintained by suitably qualified personnel. Such personnel should have previous experience with lighting equipment as well as general electrical experience. This manual is intended to provide general guidance to such suitably qualified personnel. For specific guidance and technical support, contact Selecon or its authorised representative. Information in this manual shall not be deemed a warranty, representation or guarantee concerning a luminaires suitability or fitness for a specific purpose. Subject to the right to use its luminaires, Selecon does not convey any right, title or interest in its intellectual property, including, without limitation, its patents, copyrights and know-how.

3 Performer Operation Manual 3 Please read this information carefully to ensure that you are fully conversant with the Followspot operation. Safety Warnings...4 Unpacking...4 Rear Control Panel...7 Power Output Level Display...7 Power Output Control Knob...7 Hour Meter...8 On / Off Switch...8 Earth Continuity Indicator...8 Peak / Flat Lamp Adjustment Control Knob...8 Earth Test Point...8 Side Control Panel...9 CTO Filter Control...9 Iris Control...9 Cutter Controls...9 Goboholder Accessory...9 Dowser Control Frost Control Pan and Tilt Adjustment Beam Angle Control Focus Scale Colour Changer Travel Lock Fitting colour filter Operating the Colour Changer Filter Cooling Fan Assembling your Followspot... Error! Bookmark not defined. Yoke Balance Adjustment Cable Storage Compartment Cable Conductor colour codes: Switching on the Performer Series 2 Followspot Fuse Holder / Circuit Breaker Performer Lamp Specifications and Operating Notes Lamp Fitting and Replacement Aligning the Lamp Safe Practice Maintenance Cleaning the front and rear lens Replacing the Dichroic CTO Filter Replacing the Frost Safety Accessories... Error! Bookmark not defined. Power Schematic Exploded Parts Diagram Replacing the Rear Tray Assembly w/electronic Ballast Product weights and dimensions (mm) Recycling of Packaging Limited Warranty... 22

4 Performer Operation Manual 4 Safety Warnings DANGER: The lamp used emits short wave ultraviolet radiation which is harmful to skin and eyes. Use only fully enclosed in the fixture, and never observe the lamp directly. Not for residential use. CAUTION: Hot Surfaces. Avoid contact by persons or materials. The Performer has some hot surfaces. Be careful to avoid burns. Take care with the lamphouse. We suggest the use of leather gloves when operating these luminaires. SAFETY - Mains Power Isolation The Performer is fitted with a micro-switch that automatically disconnects the mains power when the lamp holder is removed. However, it is also recommended that the luminaire should always be electrically isolated from mains power before re-lamping, cleaning or servicing. CAUTION: Risk of fire - Use only with 1200 watt lamp. CAUTION: These luminaires are not suitable for mounting on a normally flammable surface. These luminaires are not suitable for outdoor use, without suitable weather protection. D 5.0m KG The luminaire should be at least 5.0 metres / 15 ft away from the nearest object it is lighting. Heavy weight. Do not attempt to lift alone. Follow all relevant health and safety directives for lifting heavy weights. Unpacking Before *discarding the packaging, ensure that you have the following items: 1. Performer Series Followspot 2. Performer Series Yoke Assembly 3. Performer Series Operation Manual and lamp documentation. 4. Allen Key 5. Stand 6. Lamp *Note: Refer to Manual Section Recycling of Packaging Pg#24.

5 Performer Operation Manual 5 Your Performer Series Followspot Rear Control Panel Side Control Panel Tilt Control Zoom/Lens Control Pan Control Colour Changer Stand

6 Performer Operation Manual 6 Colour Changer Travel Lock Cable Compartment Lamp Access Cover

7 Performer Operation Manual 7 Rear Control Panel Power Output Level Display Power Output Control Knob Hour Meter On / Off Switch Circuit Breaker Earth Continuity Indicator Earth Test Point Peak / Flat Adjustment Control Knob Rear Handle Power Output Level Display This shows the Power Output Level of the Followspot. Power Output Control Knob This is used to set the output to the desired level and has a variable range of 60% to 100%. When at 100%, the power output displays [FF]. Important Note: Philips has designed this lamp to operate from W. Maximum lamp life is achieved at 1200W which equals 85 on the power output level display. Prolonged use above or below this level will shorten the lamp life.

8 Performer Operation Manual 8 Hour Meter This shows the total elapsed time the Performer Series Followspot has been switched on. The Hour Meter is intended to serve as a guide for the elapsed hour use of the lamp, to enable the replacement of the lamp when the recommended lamp life hours have elapsed (750 hours) When switched on for the first time, the Hour Meter will display an elapsed time of one hour. Before leaving the factory, the Performer Followspot is switched on for one hour as part of the testing cycle. When the lamp is replaced, it is good practice to record the setting on the hour meter in a log book. This enables the user to know when subsequent lamps should be replaced. On / Off Switch Used to turn the Performer Series Followspot on and off. The circuit breaker for the Performer Series Followspot is an integral part of the switch. Manufacturer: E T A Part Number: 3120-F72R-N7M1-A30QB4 Rating: 16A Selecon Order Code: FSELE006 Earth Continuity Indicator This should be illuminated green when the Performer Series Followspot is switched on. Important Note: If the indicator is not illuminated, do not touch the Followspot. Switch the Followspot off at the mains power supply, and contact a qualified service agent. Peak / Flat Lamp Adjustment Control Knob This is used to alter the field of the beam between Peak and Flat. The peak beam gives a central hot spot falling off evenly to the beam edges. Flat adjustment provides a visually even light beam. Earth Test Point Use this point to place the electrode when testing the earth connection on the Followspot. Important note: The Followspot contains electronics. Do not perform a MEGA style test. Damage to the unit may result and will void your warranty.

9 Performer Operation Manual 9 Side Control Panel Position Stop Dowser Control Goboholder Accessory Slot CTO Filter Control CTO Filter Control Iris Control Cutter Knobs Frost Control The CTO Filter is used to lower the colour temperature of the beam from 6300 K to 3200 K, to balance with halogen light sources. The filter can be changed, refer to page 18. Iris Control The Iris is used to alter the size of the beam without changing the zoom control. In the closed position, the iris blacks out the beam. In the open position, the iris is at its largest diameter. There is a reference scale adjacent to the iris to record cue levels. Important note: When setting the beam angle, ensure the iris is fully open. When setting the focus, iris down to a small spot and set the desired focus. The position stop on the iris is used to reduce the travel of the iris from open to closed. Turn the stop anticlockwise to loosen it, and push down and slide it to the desired position. Turn clockwise to lock the stop in place. Cutter Controls The cutters are used to change the shape of the beam from a circular shape to a rectangular or square shape. The V cutter control is for the vertical cutters, and the H cutter control is for the horizontal cutters. The two cutters comprising each axis are linked. Goboholder Accessory A B size gobo or pattern can be fitted to the Performer Series Followspot if required. To fit a gobo, remove the gobo cover with a Philips screwdriver, and slide the gobo holder accessory (Order code: 28PFGH) into the slot provided. Make sure the spring clips are facing towards the front of the Followspot. Put the cover in a safe place.

10 Performer Operation Manual 10 Dowser Control The Dowser mechanically dims the light output. In the closed position the light output is zero or 00%. When in the open position, the light output from the Followspot is at maximum or 100%. There is a reference scale adjacent to the dowser to record cue levels. The position stop on the dowser is used to preset the maximum output by reducing the travel from open to close. Turn the stop anticlockwise to loosen it, and slide it along to the desired position. Turn clockwise to lock the stop in place. Frost Control Frost softens the edge of the beam. The frost can be changed, refer to page 18. Pan and Tilt Adjustment The pan and tilt handles have a variable clutch system. The movement friction can be adjusted to suit the operator s preference. From the locked position, Pan Twist the pan control clockwise to increase the movement friction, and anticlockwise to decrease the movement friction on the pan axis. The operating range from the locked position (full clockwise) is one half turn anti-clockwise. This will bring the clutch to the minimum friction position for pan operation. Tilt Twist the tilt control clockwise to increase the movement friction, and anti-clockwise to decrease the movement friction on the pan axis. The operating range from the locked position (full clockwise) is one half turn anti-clockwise. This will bring the clutch to the minimum friction position for tilt operation. Beam Angle Control To set the beam angle, twist the lens handles a ¼ turn anti-clockwise, and slide to the desired position. Twist the lens handles a ¼ turn clockwise to lock in place. - the front lens defines the beam angle. - the rear lens defines the focus hard to soft. Focus Scale There are reference scales below the lens control handles to record cue positions.

11 Performer Operation Manual 11 Colour Changer Colour Frame Release Lever Colour Frame Lever Travel Lock Release Knob Colour Frame Spring Clip The colour changer is located behind the lens unit on the front of the Followspot, and will take up to six frames of colour filter. For maximum filter life, please note the following: 1. Use only a quality colour. 2. Place dark / saturated colours in the front frames. 3. Make sure there are no wrinkles in the colour filter, and it is held securely around the whole diameter of the frame. 4. Choose appropriate setting for the filter fan (refer to pg12). Im p ortant note: When lifting the Foll owspot, do not hold the colour changer or front lens un i t. Use the side handles provided.

12 Performer Operation Manual 12 Travel Lock To protect the frames of the colour changer during travel, they are stowed in the upper position, and fixed in place with the travel lock. To release the frames, pull down the travel lock by pulling out the silver knob mounted on the inside of travel lock, slide and drop the frames down to the lower position. Push the travel lock bar into the top position, and lock in place. To lock the frames in the upper position, pull out the travel lock and swing out the travel lock bar. Push the frames to the upper position. Swing the travel lock bar into the lock position and click the travel lock into place. Fitting colour filter The filter holder is designed for a filter size of 275mm (10.83 inch) diameter. To fit colour filter into the frames of the colour changer, take the following steps: 1. Each frame has a spring clip holding the filter holder in place. Slide the clip back and take out the filter holder. 2. Use the filter holder as a template to cut out the colour filter. 3. Place the colour filter into the filter holder, and then place into the frame. Slide the clip over the filter holder to lock the filter holder in place. 4. For easy reference, write the filter name in the space provided above each frame lever. Do not use a permanent marker. Operating the Colour Changer The colour changer works in the boomerang style, ie bringing in one colour frame into place will release the colour frame currently in position. To release a colour frame leaving no frame in the beam (commonly referred to as open white ), press the colour frame release lever located beside colour frame lever No.1. Filter Cooling Fan The Filter Cooling Fan is used to prolong Colour Filter Life. There are three fan settings. O Off No filter being used. Use this setting to minimise fan noise. 1 Speed One Slow speed. Use this setting for light and medium colour filters. 2 Speed Two Maximum Speed. Use this setting for dark saturated filters.

13 Performer Operation Manual 13 Fitting colour filter Warning: Heavy weights are involved in the following operation. Do not attempt this operation alone. Always assemble the Performer Series Followspot in the following order: Unfold the stand on a clean flat surface, taking care to ensure the base legs are fully extended and there is enough room to pan and tilt the Followspot in the space provided. Make sure all stand lock off knobs are fully tightened. Place the Performer Series Yoke Assembly on the Followspot stand, taking care to ensure the 40mm OD top tube is fully placed into the Yoke Receptacle. (If necessary, loosen the allen head screws slightly before sliding yoke assembly onto stand tube) Tighten the two M5 Allen head screws on the Performer Series 2 Yoke Assembly using the Allen Key provided. Important Note: Pick the Performer Series Head up using the guide rails only. Never lift the Performer Series by holding onto the front lens unit. To facilitate flying or motorised lifting, the Performer Series Followspot must be rigged with two strops. The recommended location for these strops to prevent damage and facilitate safe lifting are shown in the photos below. Only suitably qualified personnel with appropriate equipment should lift Performer Series Followspots. Front Strop.

14 Performer Operation Manual 14 Rear Strop Take the Performer Series unit out of the packing box, and place on a flat surface. Loosen the four M5 Allen head bolts on the triangular yoke pivot mounts using the Allen Key provided. Place the unit on the stand with the triangular yoke pivot correctly lined up with the receptacle as shown. Lock the Performer Series Head onto the stand assembly by fastening the four M6 Allen head bolts on the triangular yoke pivots.

15 Performer Operation Manual 15 Warning Failure to fit these screws may result in the Followspot falling out of the yoke resulting in possible severe injuries to personnel and damage to the luminaire. Yoke Balance Adjustment The Performer Series Followspot is shipped with the yoke in a neutral balance point position. This position is marked, to facilitate easy rebalancing. Note: balance point is influenced by position of lenses. Should you wish to rebalance the Performer Series Followspot, take the following steps: 1. Ensure the Performer Series Head is in a horizontal position, and the pan / tilt lock off knobs are securely fastened. 2. Loosen the four M8 yoke cradle mounting bolts located on each side of the luminaire. Slide the luminaire forward or backwards until the desired balance point is achieved. Take care to ensure the yoke cradle is always at right angles to the luminaire. 3. Tighten two of the yoke cradle mounting bolts, one on each side of the luminaire. To test the balance point, loosen the tilt knob and test. 4. If correct, tighten the two remaining yoke cradle mounting bolts. If not, repeat the above process. Cable Storage Compartment The Performer Series Followspot has a power supply cable storage compartment which safely stores the cable when the luminaire is shipped. To remove the cable: 1. Use a Philips screwdriver to undo the Dzus fastener on the compartment cover located on the bottom of the Performer Series 2 unit. 2. Pull out the 3m (9ft) power supply cable, taking care that there is no cable left in the compartment. 3. Close the compartment cover, taking care to ensure the cable is not caught in the cover. Important Note: Do not operate the Followspot with any cable stored in the compartment. Any cable stored during operation will affect the cooling system of the luminaire. Cable Conductor colour codes: Brown Blue Green/Yellow - Phase, Live - Neutral - Earth

16 Performer Operation Manual 16 Switching on the Performer Series Followspot Important Note: Do not connect the Performer Series Followspot to a dimmer. The Performer Series 2 Followspot can only be connected to a clean mains power supply (110V - 260V). Connecting the Performer Series Followspot to a dimmer may cause damage to the power supply, and will void your warranty. 1. Check the On / Off switch on the rear control panel is in the Off position. 2. Connect the power supply cable to a suitable clean mains power supply, checking that there is no cable left in the cable storage compartment. 3. Switch the On / Off switch to the On position. There should be a buzzing noise of short duration as the lamp is struck. If the buzzing noise is continuous, switch off the Performer Series Followspot, wait 5 minutes, and try again. 4. Check that the green earth continuity indicator on the rear control panel is illuminated. Important Note: If the indicator is not illuminated, do not touch the Followspot. Switch the Followspot off at the mains power supply, and contact a qualified service agent. 5. When the lamp has struck, it may take up to 10 minutes for it to obtain its correct output and colour temperature. Fuse Holder / Circuit Breaker The Circuit Breaker for the Performer Series 2 Followspot is integrated into the On / Off Switch. In the unlikely event this needs to be replaced, this operation should be performed by a qualified service agent. Manufacturer: E T A Part Number: 3120-F72R-N7M1-A30QB4 Rating: 16A Selecon Order Code: FSELE006 Performer Lamp Specifications and Operating Notes The Performer Series Followspot uses a short arc MSR Discharge Lamp. Manufacturer: Philips Type: MSR Gold 1200 Fast Fit Lamp Wattage Range: W Lampbase: Patented Lumen output at 1200W: 95,000 lm Efficacy Source (1200W): 80 lm/w Minimum ignition Supply Voltage: 207 V Arc Size: 5mm Philips Order Code: Average Lamp Life: 750 hrs Colour rendering index at 1200W 80 Colour temperature at 1200W: 6300K Chromaticity coordinates (1200W) X:.318 Chromaticity coordinates (1200W) Y:.327 Replace only with the above lamp, which is available from your Selecon Dealer (Order Code MSRMINIQF) Do not exceed the rated lamp life. Doing so will risk explosion of the lamp, and damage to the Performer Series Followspot. This is not covered under warranty. Replace after 750 hours. Please note that the quoted lamp life is a guideline only, and not an exact figure. In practise the lamp life is reduced due to the following factors:

17 Performer Operation Manual High humidity and ambient operating temperatures 2. Dusty / Dirty ambient operating conditions 3. Each On / Off cycle 4. Prolonged use at half or full (1400 W ) Power Output Take care to read the operating instructions and warnings provided by the lamp manufacturer included with your lamp, and follow the instructions for safe disposal of the lamp at the end of its operating life. Lamp Fitting and Replacement Isolate electrically before re-lamping the luminaire. Also be aware that the lamp or luminaire may still be hot, so exercise necessary caution to avoid burns. To fit or replace the lamp in the Performer Series 2 Followspot, take the following steps. 1. Check the Followspot is switched off, and the power supply cable is disconnected from the mains power supply. 2. Open the lamp access cover on the rear underside of the Followspot by undoing the two Dzus fasteners with a Philips screwdriver, and hinge down. 3. To remove the lamp from the holder, carefully turn anti-clockwise and pull out. Dispose of the used lamp according to the manufacturers instructions. 4. Remove the new lamp from its packaging, taking care to follow the lamp manufacturers handling instructions. Retain the packaging for future use, and for any potential warranty claims. Lamp manufacturers will often disallow warranty claims if there is no original packaging showing batch information. 5. Carefully insert the new lamp into the holder, and turn clockwise until it clicks into the locked position. Please note that the lamp is designed to fit one way only into the holder. Double check that the lamp is fully locked into position. 6. Close the lamp access cover. Your Performer Series Followspot is now ready to check the lamp alignment. Aligning the Lamp Important note: The Performer Series Followspot is supplied with the lamp already aligned. These instructions are only for alignment of a new lamp. Due to the precise tolerances of the lamp in the optical system, only minimal adjustment (if any) should be necessary. To simplify aligning the lamp, ensure the following steps are completed. 1. Switch the Followspot on. 2. Allow the lamp to achieve its correct operating temperature and brightness. 3. Turn the Peak / Flat control knob to the peak setting. 4. On the side control panel, ensure the operator controls are set to the following positions: a. CTO : Out b. Iris : Open c. Vertical Cutters : Open d. Horizontal Cutters : Open e. Dowser : Open f. Frost : out 5. Slide the Zoom Control to the wide position, and focus the beam to a hard edge. 6. Remove any colour frames from the beam.

18 Performer Operation Manual Shine the Followspot (with power output turned down) onto a flat surface 10+ Metres (18+ feet) away. For distances under 10 metres, turn the power output down further until the beam can be observed comfortably or shine the beam onto dark surface. The Followspot is now ready to align the lamp. Using a Philips screwdriver, initially adjust any one of the three position screws located in the centre of the lamp access cover (clockwise or anticlockwise). Observe the movement of the hot spot of the beam to determine how to further adjust the three screws (clockwise or anticlockwise), to move the hot spot towards the centre. Only minimal turning (if any) will be required. Once the lamp is aligned, the Peak / Flat control knob can be used to adjust the field of the beam to the desired setting. Safe Practice Heat The Performer Series Followspot incorporates an innovative design to effectively remove the heat out of the luminaire, away from the critical heat-sensitive components such as the lamp base and wiring. The components that form part of the heat removal system will operate at temperatures which can burn you!!! Take care in handling the luminaire. We recommend that the Followspot is cooled down before any maintenance is performed inside the luminaire. Fans and Cooling Vents Check before use to ensure all fans are operational, and there is nothing blocking the fans or vents. Do not operate if any of the fans are not working. Tilt Lock Take care when releasing the tilt lock as the luminaire may suddenly swing down. Mains Isolation The Followspot is fitted with a micro-switch that automatically disconnects the mains power when the lamp access tray is opened. However, it is also recommended that the luminaire should always be electrically isolated from mains power before re-lamping, cleaning or servicing. Maintenance Important note: Make sure the Followspot is switched off and disconnected from the mains supply before opening the side cover. To open the side cover, unscrew the rear side cover screw with the Allen key provided. Unscrew the front cover thumb screw by placing your hand up through the colour changer bay. Front Cover Screw Rear Cover Screw Reach through colour changer opening to release front cover screw Swing the cover out to the open position as shown.

19 Performer Operation Manual 19 Cleaning the front and rear lens Use a soft cloth and cleaning alcohol / methylated spirits to clean the surfaces of the lens. Replacing the Dichroic CTO Filter To replace the Dichroic CTO filter, slide the retention clip to the top position, and lift out the filter. Place the replacement filter into the holder and slide the retention clip to the bottom position. Replacing the Frost To replace the frost, slide the retention clip to the top position, and lift out the frost. Place the replacement frost into the holder and slide the retention clip to the bottom position. The above are the only maintenance tasks which can be safely carried out by suitably qualified personnel. Refer below - Safety note. Safety Selecon has manufactured this luminaire in accordance with recognised best practices to recommended international safety standards. It is your responsibility to maintain this luminaire in good & safe working condition. Repairs should only be carried out by suitably qualified persons. Do not operate the luminaire with cracked lens, damaged cable, etc. Consult your Selecon distributor for assistance. Only replace damaged parts with authorised Selecon spares.

20 Performer Operation Manual 20 Power Schematic Exploded Parts Diagram Please refer to Selecon website: Replacing the Rear Tray Assembly w/electronic Ballast Important note: Make sure the Followspot is switched off and disconnected from the mains supply before opening the rear tray. Heavy weights are involved; this operation must not be attempted alone. Only attempt this operation if you are suitably trained and qualified! 1. Return the Followspot to the horizontal position, and lock in place. 2. Disconnect the power supply cable for the fan by unplugging the connector the positions shown. Access through side extrusion door. 3. Remove the rear tray allen head screws as shown.

21 Performer Operation Manual Carefully slide the rear tray assembly out of the followspot, taking care to ensure the mains supply cable is not snagged during the operation. Warning: The balance point of the followspot will shift as the tray slides out. Have one person to steady the followspot in the horizontal position. 5. Remove the assembly, and install the replacement assembly, Reverse the above steps. Product weights and dimensions (mm) Performer Toru Followspot 4-8 Weight (inc Stand) : 108 kgs / 238 lbs

22 Performer Operation Manual 22 Recycling of Packaging Selecon recognizes the importance of shipping your Performer Series Followspot so that it arrives in perfect condition; accordingly we use a variety of packaging materials to protect Performer Series Followspots. But we also care about the environment, as do many of our customers. That's why we make sure our packaging materials are recyclable, and, where possible, made from recycled materials themselves. The Pallet/Plywood All timber packaging is manufactured from new export grade materials with the solid timber pallet certified in accordance with ISPM15 requirements. The Box The corrugated box is 100 percent recyclable for use in the manufacture of other paper products. Corrugated shipping containers are one of the most commonly accepted materials at recycling programs or at recycling centres globally. The Cushions The cushions protecting this product during transportation are made of Instapak polyurethane packaging foam, a material that minimizes the amount of packaging used without compromising the protection of shipped goods. Instapak packaging is also produced without chlorofluorocarbons (CFCs) or hydrochlorofluorocarbons (HCFCs), which have been associated with the depletion of the ozone layer. Reuse Instapak foam cushions can be reused for multiple shipments or reshaped manually into carton fillers to fit the next product shipped. Instapak Foam Return Locations For current return locations in North America, call toll-free: For current return locations in Europe, call: (31) (24) Or visit the website: Instapak foam may be bagged, baled or boxed. The foam must be clean, dry and not adhered to any corrugated material. Limited Warranty Selecon New Zealand Ltd. ( Selecon ) warrants its luminaires against defects in materials or workmanship. The term of this warranty is based on the product usage and is from the date of delivery. Usage Entertainment, Theatre Term - Three Years Entertainment, Theatre relates to the typical conditions found in a theatre performance venue viz: 4 6 hrs per day, six days per week. Usage Architectural, Display Term - Three Years Architectural, Display relates to typical usage such as display lighting in a Museum viz: hrs per day, seven days per week. Other ALL Electromechanical / Electronic Devices This warranty is void in any of the following circumstances: (a) The luminaire has been misused, neglected, damaged or abused. Term - One Year

23 Performer Operation Manual 23 (b) The luminaire has been improperly installed, operated, repaired or maintained. (c) The luminaire has been modified. (d) The luminaire has been connected to other equipment with which it is not compatible. (e) The luminaire has been used or stored in conditions outside its electrical or environmental specifications. (f) The luminaire has been used for purposes other than for which it was designed. (g) The luminaire has been used outside its stated specifications and operating parameters. Correct installation of the luminaire is the owner s responsibility. To assert a warranty claim, complete Selecon s return authorisation form (available from Selecon). Return the luminaire to Selecon or its authorised agent. If Selecon accepts the warranty claim, Selecon will provide, or arrange for, service, repair or replacement as Selecon shall determine in its sole discretion. Selecon shall bear the cost of such service, repair or replacement. However, the owner shall bear the cost of freight and insurance on the luminaire, both ways. If Selecon does not wish to service, repair or replace the defective luminaire, it shall refund the purchase price. Selecon s sole responsibility is to repair, replace or service a luminaire subject to a valid warranty claim. Under no circumstance will Selecon be liable for direct, indirect, incidental, special or consequential costs or damages, including dismantling and re-installation costs, loss of operations or profits, to the maximum extent permitted by law. Selecon accepts no liability for personal injury or property damage resulting from failure to heed relevant operating and safety procedures specified by Selecon or imposed by law. This is an express warranty. Selecon disclaims any other express or implied warranties, including warranties of merchantability or fitness for purpose, to the maximum extent permitted by law. Some jurisdictions do not allow limitations or disclaimers of implied or statutory warranties. Some jurisdictions do not allow disclaimers or exclusions of consequential or incidental damages. Therefore, the above disclaimers, limitations and exclusions may not apply in all jurisdictions in which Selecon sells its luminaires. This warranty gives the owner specific legal rights. The owner may have other rights or remedies pursuant to the laws in its territory. Nothing in this limited warranty should be construed as limiting or restricting any other statutory right or remedy of the owner, except for such limitations or restrictions herein as may be allowed by the law of the territory. Selecon has a policy of continual product improvement and specifications are subject to change without notice. Contacting Selecon Selecon New Zealand Ltd Kawana Street, Northcote, Auckland 0627, New Zealand Tel: , Fax: info@seleconlight.com