indoor lighting solutions Main catalogue

Transcription

1 indoor lighting solutions Main catalogue

2 Appareo ed by Howl Studio It is like magic. The luminaire is lit but where is the light source? Appareo is a suspended luminaire which maximises the design flexibility offered by LED s without compromising on the requirements for efficiency and ergonomics. The starting point was a new type of glass diffuser which acts as both the reflector and the louvre. The light is distributed indirectly towards the ceiling and directly down towards the work surface. Providing the ambient and task lighting levels demanded in contemporary office spaces. Unlit the transparent glass screen is housed with a slender aluminium frame for the height of discretion. When lit, the LEDs positioned across the slide of the luminaire bring the screen to life, increasing the opacity and guiding the light for an optimal visual experience. The result is a fresh, crisp light that does not dazzle. 8

3

4 523 Appareo Luminaire System, W Colour temp., K Lightdistr. Luminous flux, lm Efficiency, lm/w kg White Black / Luminaire must be completed with desired function. See table with suffix codes. For current information on output and luminous flux, please refer to our website. Information LED-Luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 4000 K 80 L h MacAdam 4 SDCM For further information on LEDs, please refer to the Technical Information chapter. Suffix code -402 DALI -442 e-sense ActiLume single luminaire Add suffix code to the end of the luminaire part number to indicate required function. Only one suffix can be added. Two-point wire pendant. Wire suspension and friction lock included with luminaire. Balanced. External ballast box is mounted directly to ceiling or placed loosely above ceiling. Connection Luminaire is connected in the ballast box with 230 V, built-in LED ballast in ballast box. Cable entry on top or through the knockout in the side. Snap-in terminal block mm², 1-phase throughwiring possible. The luminaire is equipped with a 1.5 m mains cable mm² between the luminaire and the external ballast box. Body in extruded aluminium and ends in cast metal. The luminaire is lacquered in black (RAL 9005) structured or white (RAL 9016) structured. Louvre Edge-lit clear prismatic acrylic diffuser (PMMA). Average luminance <2000 cd/m². Dimming DALI or e-sense ActiLume as standard. Miscellaneous Appareo has side-emitting LEDs, as a result the luminaire s acrylic diffuser is completely transparent when switched off and provides an evenly luminated surface when lit. e-sense ActiLume is integrated into the ends of the luminaire Ballast box 374, The mounting point for the wire suspension is adjustable lengthways. 10

5 523 Appareo Circular Luminaire System, W Colour temp., K Lightdistr. Luminous flux, lm Efficiency, lm/w kg White Black / For current information on output and luminous flux, please refer to our website. Information LED-Luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 4000 K 80 L h MacAdam 4 SDCM For further information on LEDs, please refer to the Technical Information chapter. Wire suspension (4 m) with ceiling bracket and friction lock, is included with the luminaire. External ballast box is mounted directly to ceiling or placed loosely above ceiling. Connection Luminaire is connected in the ballast box with 230 V, built-in LED ballast in ballast box. Cable entry on top or through the knockout in the side. Snap-in terminal block mm², 1-phase throughwiring possible. Supplied with a 3 m white fabric cord between luminaire and external ballast box. Luminaire body in cast aluminium. The luminaire is lacquered in black (RAL 9005) structured or white (RAL 9016) structured. Ballast box in plastic. Louvre Edge-lit clear prismatic acrylic diffuser (PMMA). Average luminance <3000 cd/m². Dimming DALI dimming as standard. Miscellaneous Appareo has side-emitting LEDs, as a result the luminaire s acrylic diffuser is completely transparent when switched off and provides an evenly luminated surface when lit. pendant/surface When switched off the luminaire is completely transparent Ballast box Ballast boxes can be placed above ceilings or surface mounted directly to the ceiling. 11

6 Notor G2 ed by Julle Oksanen and Vesa Honkonen Fagerhults classic Notor G2 luminaire has now been brought right up-to-date using the latest in LED technology. The expansive range spans suspended, surface mounted and recessed variations, offering the flexibility to maintain a consistent aesthetic across numerous applications. Notor is characterised by discretion. Its minimalist style and clean line design is constructed of aluminium with a natural anodised finish. In continuous runs Notor provides an unbroken line of light in the ceiling while the L-coupler offers the scope to create more varied installations. The LED variation is lit all the way to the end-caps of the luminaire housing, further enhancing its visual appeal with illuminated corners. The luminaires can be connected using a snap-in connector for safe and efficient installation, while providing additional protection to the light sources and other technology during installation. Notor Recessed, see page

7 Notor LED 1. Notor LED utilises the benefits of LEDs. The luminaire has an exceptional level of uniformity in the diffuser and a high luminous efficacy. Notor LED can be surface mounted or suspended via a wire pendant. 2. The system is connected via end-cap of the start luminaire. The wiring is hidden by the end-cap. The start luminaire can also be used in a single installation. 3. For continuous and system installations, throughwiring is achieved via a snap-in connection: the luminaires are clicked together and then secured with a screw joint. Each luminaire unit has an integrated ballast The continuous luminaires have an unbroken line of light without dark fields at the transition between the luminaire units. 5. The L-joints provide full lighting, creating an aesthetically pleasing transition in corners. 6. The LEDs are protected against contact by a plastic cover which prevents external influences

8 523 Notor LED Luminaire System, W Colour temp., K Luminous flux, lm Efficiency, lm/w kg Start Continuous Straight luminaire Illuminated corner Right * Left * * Only for suspension and in closed systems. For current information on output and luminous flux, please refer to our website. Information LED-Luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 4000 K 80 L h MacAdam 4 SDCM For further information on LEDs, please refer to the Technical Information chapter. Suffix code -402 DALI Add suffix code to the end of the luminaire part number to indicate required function. ed for single or continuous installation with surface mounting and via a wire pendant and special loops that give flexible c/c spacing. Can also be mounted on the wall via the wall bracket, see accessories. Connection The luminaire is equipped with an access hole for cabling on the top. A special short end with cable entry is used for a surface mounted mains cable, see accessories. The luminaire unit is equipped with a throughwiring cable (5 1.5 mm²) and a snap-in connection in each end-cap. In a continuous installation, the luminaire row should always begin with a start luminaire. Luminaire unit in natural anodised, extruded aluminium finish. Louvre Opal plate in frosted acrylic (PMMA). Accessories Assembly fittings and supplementary components, see accessories. Miscellaneous The LEDs are protected against contact. Illuminated corners with wiring option can only be suspended. The illuminated corners can be used as a start luminaire and are equipped with through-wiring and quick connection in one end. The corners can only be used in closed systems. pendant/surface All variants By continuous installation all wiring needed is performed in the start luminaire, which provides a safe and efficient installation. A₁ A A₂ A₁ A A₂ 100 A A₁ A₂ A A₁ A₂ LED provides uniform luminance and completely illuminated corners. 19

9 Notor G2 1. The range is provided with connections integrated into the luminaires. The opening on the luminaire runs to the opposite end-cap instead of terminating with a connection module The connection takes place at the end of the start luminaire and is concealed by a cover plate on the bottom Continuous mounting can provide aesthetic and practical advantages. The continuous mounting is made completely without any visible details, the screw fixing gives the mechanic stability. Continuous- or system mounting always start with a connection luminaire that connects to continuous luminaires. Continuous connecting creates an unbroken line of light Notor G2 also offers possibilities to mount a system using L-, T- or X-connections. If you want to mix direct and indirect luminaires in the system, you can use an exchange unit Notor G2 system connections 1) 4) 2) 1) Exchanger, Direct/Indirect 2) emled-unit 3) L-connection 4) T-connection 5) X-connection 6) Wall bracket with connection, left 7) Wall bracket 8) Wall socket 3) 5) Notor G2 system dimensions Notor G2 wall holdings A 1 A 2 A 3 6) 7) A 4 W A 1 A 2 A 3 A 4 A / / /28/50/ /35/45/49/73/ / /28/50/ /35/45/49/73/ ) A 5 20

10 Avion Avion has a delicate beauty masking a robust design. An elegant flow of light which creates an impression of weightlessness, designed to act as a striking solitary luminaire, or to form a system where its long dimensions create a fascinating linear interaction. Avion is Fagerhult s new extensive range of pendant luminaires. Behind the clean lines hides an innovative design and advanced lighting technology. The range comprises of five different combinations of direct and indirect light distributions. Efficiency and visual comfort are ensured via Fagerhult s Lamell and Beta r5 louvres. The light source for the indirect distribution is discreetly positioned in a subtle elevation at the top of the luminaire, while the thin lines and the concaved edges provide the essence of the design. The distinctive colour contrasts along the side attracts attention and enhances its form. Avion can be continuously installed, seamlessly integrated via continuous connectors. The addition of flexible connectors offers the potential to create curved lines, with variations at each connection point. Avion achieved an honourable mention in the 2009 red dot design awards. 26

11 523 Avion 50 Beta, Delta, Lamell Luminaire, single installation incl. end-caps FDH kg White/black Grey/white Beta 1 25/ / / / / / / / Delta 2 25/ / / / Lamell 1 25/ / / / / / / / Luminaire, continuous installation excl. end-caps FDH kg White/black Grey/white Beta 1 25/ / / / / / / / Suffix code -368 DALI/Phase-pulse control -409 Phase-pulse control, one pull-cord -436 DALI/DSI/switchDIM -218 e-sense smartswitch absence detector -219 e-sense smartswitch on/off -220 e-sense smartswitch -367 e-sense ActiLume master luminaire -384 e-sense ActiLume with single luminaire pull dim-switch -427 e-sense Connect -428 e-sense Connect with sensor Add suffix code to the end of the luminaire part number to indicate required function. Only one suffix can be added. Wire suspension via wire lock secured directly to the luminaire. Balanced. Connection Single installation the luminaire is equipped with a 2.4 m mains cable mm² and an earthed plug as standard. Luminaires ordered with switchdim or DALI are equipped with 2.4 m mains cable mm² excl. plug. Continuous installation 5-way snap-in terminal block at each end and through-wiring cable mm² as standard. With dimming, 5-way snap-in terminal block, 1-phase through-wiring possible. Body in extruded aluminium and end-caps in cast aluminium. The luminaire is finished in a white/black (RAL 9016 structured/ral 9005) or alu-grey/white (RAL 9006 structured/ RAL 9016) design. The top cover is transparent acrylic plastic. Luminaires for continuous installation require end-caps must be ordered separately. Louvre Beta double parabolic reflector louvre with satin matt metallised aluminium side and cross-blades with excellent reflection characteristics (> 92 %), integrated into a single unit. The louvre remains attached when opened. Earthed. Delta micro-prism louvre in acrylic TPb (PMMA). Lamell alu-grey enamelled sheet steel, cross-blade louvre. Reflector Reflector material of metallised aluminium with satin matt surface. Accessories Assembly fittings and supplementary components, see accessories. 1 32/35 W, Beta 2 32/35 W, Beta 1 32/35 W, Lamell 2 32/35 W, Lamell A continuous coupler is available as an accessory. W D¹ D² D³ D⁴ D⁵ D⁶ 25/ / / / D¹ D⁶ D² D³ D⁴ D⁵ The removable end-caps partially conceal the friction lock from view. 30

12 Multilume Flat Multilume Flat is amongst the first LED luminaires to be more efficient than its T5 equivalent; producing more than 80 lumens per watt while still retaining optimal lighting ergonomics. The LED evolution of the Multilume range offers a recessed mounted solution for general office lighting. Encompassing a range of innovative features, Multilume Flat was developed to make the planning and installation processes easier, in a construction industry where margins are becoming ever tighter. Advancing from a downlight application, Multilume Flat transforms LED s into a viable solution for full general lighting with the capacity to replace its T5 incumbents. A generous number of closely positioned diodes work in unison to provide a light which can be shaped by the choice of louvre. The micro-prismatic Delta closely controls the intensity of the light, achieving the requirements for 3000 cd/m². The Opal alternative provides a crisp light and a somewhat whiter surface. To further enhance its efficiency the luminaire can be optimised for lighting control, reacting to both incidental daylight and human presence. As part of a holistic approach, Multilume Flat has been designed to address the tight time requirements and restricted ceiling heights in many construction projects. The luminaire is only 50 mm high and has a flexible ballast box attached by Velcro which can be detached and positioned next to the luminaire. The frame consists of an aesthetic but sturdy aluminium profile which contributes towards the clean line aesthetic prevalent in contemporary architecture. Multilume Flat is available in three different module designs; two square and one rectangular. As with all Fagerhult s LED luminaires, Multilume Flat is updated each year with the latest generation LEDs, ensuring our customers always have access to the most up-to-date technology. 140

13 Multilume Flat 1 2. In addition to the module, Multilume Flat is also available in and designs. The latter are for ceilings with visible T-bars The connection cable between the luminaire and ballast box is sufficiently long to permit the ballast box to be positioned either side of the luminaire or next to it, if the space above the suspended ceiling is restricted. 5. The ballast box has two cable entries for connection, providing the option for onward connection. 6. Models for suspended ceilings with concealed T-bars have brackets on one side that are folded over the suspended ceiling profile once the luminaire has been positioned into the ceiling. Suitable for suspended ceilings with concealed T-bars where the ceiling boards are fitted symmetrically. 7. The design of the frame on Multilume Flat is aligned with the bottom edge of the T-bar profile, which gives the suspended ceiling a clean and neat appearance. recessed pendant/surface

14 523 Multilume Flat Opal Luminaire LED-module, lm, W Length Width Colour temp., K Luminous flux, lm Efficiency, lm/w kg Visible T-bars (VTB) 1000, , , , , , Concealed T-bars (HB)/D-edge, symmetrical attachment of ceiling boards 4000, , For current information on output and luminous flux, please refer to our website. Luminaire for recessed mounting in ventilated or unventilated suspended ceilings. The luminaire must not be covered with insulation. For further details please refer to the assembly instructions on our website. Installed in suspended ceilings with visible T-bars (25 mm). Also variant for concealed T-bars (symmetrical suspended ceiling with concealed bars). Connection Connection in ballast box. The ballast box can be detached and positioned next to the luminaire. Snap-in terminal block 3 1,5 mm² (5 1,5 mm² where dimming is required). Can also be supplied with 2,5 m mains cable and earthed plug. Luminaire body in white enamelled sheet steel (RAL 9016). Frame in white enamelled aluminium (RAL 9016). Louvre Opal Opal plate in frosted acrylic (PMMA). Miscellaneous Enclosure class IP 44 under suspended ceilings and IP 20 above suspended ceilings. recessed pendant/surface Information LED-Luminaire Colour temp. (CCT) Ra (CRI) Life Colour quality 3000 K 80 L h MacAdam4 SDCM 4000 K 80 L h MacAdam4 SDCM For further information on LEDs, please refer to the Technical Information chapter. Suffix code -03 Connection cable with earthed plug, RKK mm², L=2.5 m DALI Add suffix code to the end of the luminaire part number to indicate required function. Only one suffix can be added A 2 HB B 2 C 2 A 1 C B 1 82 A 1 A 2 B 1 B 2 C 1 C HB Ballast box There is full alignment between the luminaire and the suspended ceiling. 143

15 523 Multilume Flat Delta Luminaire LED-module, lm, W Length Width Colour temp., K Luminous flux, lm Efficiency, lm/w kg Visible T-bars (VTB) 1000, , , , , , Concealed T-bars (HB)/D-edge, symmetrical attachment of ceiling boards 4000, , For current information on output and luminous flux, please refer to our website. Luminaire for recessed mounting in ventilated or unventilated suspended ceilings. The luminaire must not be covered with insulation. For further details please refer to the assembly instructions on our website. Installed in suspended ceilings with visible T-bars (25 mm). Also variant for concealed T-bars (symmetrical suspended ceiling with concealed bars). Connection Connection in ballast box. The ballast box can be detached and positioned next to the luminaire. Snap-in terminal block 3 1,5 mm² (5 1,5 mm² where dimming is required). Can also be supplied with 2,5 m mains cable and earthed plug. Luminaire body in white enamelled sheet steel (RAL 9016). Frame in white enamelled aluminium (RAL 9016). Louvre Delta microprism louvre in acrylic (PMMA) with a thin opal diffuser (acrylic/pmma) on the inside(pmma). Miscellaneous Enclosure class IP 44 under suspended ceilings and IP 20 above suspended ceilings. Information LED-Luminaire Colour temp. (CCT) Ra (CRI) Life Colour quality 3000 K 80 L h MacAdam4 SDCM 4000 K 80 L h MacAdam4 SDCM For further information on LEDs, please refer to the Technical Information chapter. Suffix code -03 Connection cable with earthed plug, RKK mm², L=2.5 m DALI Add suffix code to the end of the luminaire part number to indicate required function. Only one suffix can be added A 2 HB B 2 C 2 A 1 C B 1 82 A 1 A 2 B 1 B 2 C 1 C HB Ballast box

16 Notor Recessed Fagerhult s classic Notor luminaire is now also available in an LED version. The family is completed with a recessed, a suspended and a ceiling-mounted variant, which together solve any challenge presented by the lighting project. Notor LEDs are even more efficient luminaires that take up minimal space. Notor is characterised by discretion. With its small size and clean lines, Notor has become popular amongst light designers and architects who want to emphasise the shape of the room. Notor is also an obvious choice in circumstances when there is a desire to create long lines of light. All luminaires in the Notor family are available with a T5 or LED light source. Notor is based on a smart aluminium profile with a natural anodised finish and is designed to provide many opportunities for working creatively with lighting planning. Continuous installation and L-couplings are some of the features. The luminaires with LED are lit all the way out to the end cap of the luminaire housing, which provides additional freedom to play with angles and properly lit corners. The luminaires can be connected using a snap-in connector for safe and efficient installation, something which also helps to protect the light sources and other technology in conjunction with installation. Notor G2, see page

17 Notor Recessed LED 1. A coupler bracket is used to connect the luminaires together in a continuous installation by hooking into one luminaire and screwing into the next The end caps are secured to the luminaire profile with two screws. 3. Different end-caps are used depending on the louvre. The end-cap for flush opal version follows the profile of the fitting, while the dropped opal end-caps extends beyond the fitting top cover the acrylic diffuser A cover plate is used in the continuous installation of luminaires at the start and end on the installation. This is to prevent gaps as the aluminium bodies and acrylic louvres expand very differently linearly. Cover plate comes with start luminaire. recessed pendant/surface Suspension fittings are assembled before the luminaire is raised to the ceiling. When the screws are tightened from below, the suspension fitting swings out and locks the luminaire. 8. There is a 600 mm long dummy section that can be cut to length in order for the continuous installation to reach the desired length in instances when the luminaires are not required throughout the run. 7 8 Continuous/End Continuous/End Continuous/End L-Coupler L-Coupler Start Start Start L-Coupler Start 9. Please Note! A start luminaire is used after each L-coupling for onward connection. Max continuous installation length 30 m, limited by the linear expansion of the different materials. If a longer continuous installation is required you can start a new installation

18 523 Notor recessed LED Opal flush Straight luminaire LED-module, lm, W Colour temp., K Length Luminous flux, lm Efficiency, lm/w kg Single Start Continuous 1250, * , , , * , , * Not possible to be mounted as single luminaire in ceilings with visible T-bars (VTB). For current information on output and luminous flux, please refer to our website. Luminaire for mounted in ventilated or unventilated suspended ceilings. Installed in suspended ceilings with visible T-bars, VTB (25 or 15 mm) or one-piece suspended ceilings. Connection Connection by means of a connection box on top of the luminaire. Wieland Chassis connector 3-way (GST 18i3), with dimming 5-way (GST 18i5). In a continuous installation the luminaire row should always start with a start luminaire. With continuous installation the luminaire units are interconnected with a connection cable in the connection box. Luminaire body in natural anodised, extruded aluminium. With continuous installation an unbroken line of light is achieved, even via a L-coupling. Louvre Opal plate in frosted acrylic (PMMA). Miscellaneous Accessories and cables, see Accessories. Illuminated corners LED-module, lm, W Colour temp., K Module Luminous flux, lm Efficiency, lm/w kg 2500, , For current information on output and luminous flux, please refer to our website. Information LED-Luminaire Colour temp, (CCT) Ra (CRI) Lif e Colour quality 3000 K 85 L h MacAdam 4 SDCM 4000 K 85 L h MacAdam 4 SDCM For further information on LEDs, please refer to the Technical Information chapter. Suffix code -402 DALI Add suffix code to the end of the luminaire part number to indicate required function. Opal flush, 600 mm Opal flush, 1200 mm Continuous coupler bends into the frame for a single installation. Single Module A¹ A² A¹+22 A¹ A¹+22 A¹ A¹+22 A¹ Total A¹ Total A² A¹ + A¹ A¹ + A¹ + 26 A¹ Continuous Total A¹ t h 78.5 A¹ h t A² The LED board is safeguarded by the transparent contact protection with a lens function. 146

19 523 Notor recessed LED Opal dropped Straight luminaire LED-module, lm, W Colour temp., K Length Luminous flux, lm Efficiency, lm/w kg Start Single/Cont./End 1250, * 2500, , , * 2500, , * Not possible to be mounted as single luminaire in ceilings with visible T-bars (VTB). For current information on output and luminous flux, please refer to our website. Illuminated corners LED-module, lm, W Colour temp., K Module Luminous flux, lm Efficiency, lm/w kg 2500, , For current information on output and luminous flux, please refer to our website. Luminaire for mounted in ventilated or unventilated suspended ceilings. Installed in suspended ceilings with visible T-bars, VTB (25 or 15 mm) or one-piece suspended ceilings. Connection Connection by means of a connection box on top of the luminaire. Wieland Chassis connector 3-way (GST 18i3), with dimming 5-way (GST 18i5). In a continuous installation the luminaire row should always start with a start luminaire. With continuous installation the luminaire units are interconnected with a connection cable in the connection box. Luminaire body in natural anodised, extruded aluminium. With continuous installation an unbroken line of light is achieved, even via a L-coupling. Louvre Opal plate in frosted acrylic (PMMA). The louvre hangs down 10 mm from the ceiling and provides ambient luminance to ceiling and wall. Miscellaneous Accessories and cables, see Accessories. recessed pendant/surface Information LED-Luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 3000 K 85 L h MacAdam 4 SDCM 4000 K 85 L h MacAdam 4 SDCM For further information on LEDs, please refer to the Technical Information chapter. Suffix code -402 DALI Add suffix code to the end of the luminaire part number to indicate required function. Opal dropped, 600 mm Opal dropped, 1200 mm Illuminated L-coupling provides light right into the corner. Single Module A¹ A² A¹+22 A¹ A¹+22 A¹ A¹+22 A¹ Total A¹ Total A² A¹ + A¹ A¹ + A¹ + 26 A¹ Continuous Total A¹ t h h t A¹ A² Dummy section. 147

20 Notor Recessed LED Accessories 1. Mounting bracket Mounting bracket/pair Dummy section Dummy section 600 mm, Opal dropped Dummy section 600 mm, Opal flush End-cap End-cap/pair, Opal flush End-cap/pair, Opal dropped Cover unit Cover plate/pair provides IP 44 on dropped opal start luminaire used single installation. Cover plate comes with start luminaire Mains cable 1-phase, 3-way connectors (Wieland GST). Mains cable, female, length 2.0 m Mains cable, female + earthed plug, length 2.0 m Connection cables, quick connection system, 3-way White connection cable, female + male, cross-section 1.5 mm 2, 1-phase, 3-way connectors (Wieland GST). Length 1.0 m Length 2.0 m Length 2.5 m Length 3.0 m Mains cable 1-phase + dimming (Wieland GST) 5-way. Mains cable, female, length 2.0 m Connection cables, quick connection system, 5-way Black connection cable, female + male, cross-section 1.5 mm 2, 1-phase + dimming (Wieland GST) 5-way. Length 1.0 m Length 2.0 m Length 2.5 m Length 3.0 m ex. 1.0 m mm 1200 mm 647 Length Inter-connecting cable mm 1.0 m mm 1.0 m mm 2.0 m mm 2.0 m mm 2.0 m mm 2.5 m

21 Multilume Hydro Environments with stringent hygiene requirements must also have highly effective lighting and Multilume Hydro was specifically developed to address these needs. Not only does it provide professional work lighting, it also simplifies maintenance as it is easy to service and clean. All screws, clips and fasteners are placed inside to avoid the collection of dirt facilitating easy service and cleaning, with no dust traps. Multilume Hydro is designed for the T5 fluorescent lamp. This provides a number of advantages including a high light output, an economical service life and the possibility to save energy with an HF ballast The louvre module, which houses the louvre, frame and protective glass, is secured to the body via spring clips. The louvre module remains attached to the body during service and maintenance work. 2. Luminaires for recessed mounting are fitted with suspension attachments that are suitable for fixed ceilings or suspended ceilings with visible T-bars. Ceilings depth from 20 mm to 46 mm. The luminaire is always mounted from the underside. Adjustment and locking of the suspension fittings are carried out from inside the luminaire body, all for easy and quick installation. 232

22 IK Multilume Hydro Robust Beta Luminaire FSQ-E kg Module Recessed mounting Opal FDH 3 13/ Clear / Clear / Clear / Clear Surface mounting 2 25/ Clear Suffix code -03 Mains cable with earthed plug, RKK mm², L=2.5 m V -436 DALI/DSI/switchDIM Add suffix code to the end of the luminaire part number to indicate required function. Only one suffix can be added. For recessed or surface mounting. The recessed model is suitable for fixed suspended ceilings or suspended ceilings with visible T-bars. Requisite suspension fittings supplied. Ceiling thickness from mm. The luminaire must not be covered with insulation. For further details please refer to the assembly instructions on our website. Connection Cable entries fitted with blanking grommets on the top. 5-way snap-in terminal block. Luminaire body of white enamelled and anti-corrosive treated steel sheet. Louvre frame of extruded aluminium fitted with impact resistant PETG plastic protective glass. There is a seal between the frame and protective glass as well as between the frame and body. Louvre Beta double parabolic reflector louvre with side and cross-blades of satin matt, metallised aluminium with excellent reflection characteristics (> 92 %), integrated into a single unit. The frame with louvre is screwed to the body using tamperproof torx screws. The louvre remains attached when opened. Earthed. Reflector The luminaire body is equipped with a top reflector, one for each lamp. Miscellaneous The luminaire has been designed with a minimum of dirt collecting surfaces, which facilitates cleaning. Luminaire is IK 10 rated excluding 1 26 W version. IK International classification for mechanical protection; IK10 = highest class. 3 13/14 W 2 25/28 W W A 1 A 2 B 1 B 2 C / / W A B C D 25/ B 2 B 1 C A 2 C A 1 B A D The frame with louvre is screwed to the body using tamper-proof torx screws. 234

23 Indigo Ed2 ed by Epsilon The clean, simple design of Indigo Ed2 makes a clear statement. Indigo Ed2 is the only luminaire in the Indigo concept with a predominantly indirect light distribution, offering a high degree of visual comfort within the room. The Indigo Ed2 luminaires are offered in a variety of styles and variations. The indirect light is distributed via the secondary reflector, giving Indigo Ed2 soft light distribution and lighting that is sensed as balanced and comfortable. New to the family is Indigo Ed2 Hygiene a luminaire with a full glass cover for easy cleaning. 178

24 523 Indigo Ed2 R2 Perfo Hygiene Luminaire FDH kg VTB Module / / Suffix code -368 DALI/Phase-pulse control Add suffix code to the end of the luminaire part number to indicate required function. Light source W Socket 830 Fluorescent lamp FDH 14 G G For further information please refer to the Light Sources chapter. Luminaire for recessed installation in ventilated or unventilated suspended ceilings. in suspended ceilings with visible T-bars 25 or 15 mm or fixed suspended ceilings type plasterboard. Four fixing brackets included. Connection The luminaire is equipped with a 2.4 m mains cable and earthed plug. Luminaires for dimming are delivered with 5-core, free cable tails, 5-way snap-in terminal block 2.5 mm². Body and reflector of white enamelled sheet steel (RAL 9016) structured finish. Louvre frame of white enamelled sheet steel fitted with toughened protective glass. Louvre Perforated white enamelled sheet steel (RAL 9016) structured finish with opal plastic diffuser on the inside. The louvre remains attached when opened. Miscellaneous Light sources to be ordered separately. Most models can also be equipped with other ballasts for dimming. Enclosure class IP 44 beneath suspended ceilings and IP 20 above suspended ceilings. recessed pendant/surface 4-lamp, FDH A 1 W A 2 B 1 B 2 A B 4 13/14/20/ B 2 A 2 B t < A 1 The louvre frame remains attached when opened. 183

25 Pleiad G3 Pleiad G3 is the third generation of Fagerhult s successful downlight range now equipped with LED. In common with its predecessors, the focus was placed upon perfect lighting treatment, quick installation and efficiency. In G3 these concept has been taken to the next level, including automatic installation! The energy efficiency and long lifespan of LEDs come at the price of higher demands on distribution and shielding due to the increased light intensity. To combat these issues G3 was developed using an innovative reflector technology which fully exploits the efficiency of LEDs, without affecting the lighting ergonomics. The family contains numerous options for different light distributions, complemented by an extensive range of practical and decorative accessories. Speed and ease of installation has long been synonymous with the Pleaid range and G3 takes this one step further. The luminaire can be installed without any manual effort. The housing needs only be placed in the right position and then its installed automatically with the help of gravity technology. The rapid installation, combined with high efficiency and long life, ensures Pleiad G3 is an economical choice with a beneficial pay-off time. 244

26 523 Pleiad SLD G3 Surface mounted Surface mounted installation. Mounting plate with two securing holes. Connection 3-way snap-in terminal block 2.5 mm², through-wiring possible. With dimming, 5-way snap-in terminal block, through-wiring possible. Cable entry from the top of the luminaire or via 3 knock-out openings, 90 or 180. Luminaire body in white (RAL 9016) cast aluminium. Reflector Reflector in either high gloss or matt anodised aluminium. Specular metallised Advanced Anti-Glare Control ring above the LED module. Mechanical shielding 45. Luminaire LED module, lm, W Colour temp, K Luminous flux, lm Efficiency, lm/w Reflector 1100, Specular , Matt , Specular , Matt , Specular , Matt , Specular , Matt For current information on output and luminous flux, please refer to our website. Information LED luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 3000 K 80 L h MacAdam 3 SDCM 4000 K 80 L h MacAdam 3 SDCM For further information on LEDs, please refer to the Technical Information chapter. Suffix Code -365 TouchDIM/DALI Add suffix code to the end of the luminaire part number to indicate required function. Specular reflector Matt reflector Advanced Anti-Glare Control ring mounted to the reflector. 248

27 523 Pleiad SLD Basic G3 Surface mounted Luminaire LED module, W Colour temp, K Reflector 1100, Specular , Matt , Specular , Matt For current information on output and luminous flux, please refer to our website. Information LED luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 3000 K 80 L h MacAdam 5 SDCM 4000 K 80 L h MacAdam 5 SDCM For further information on LEDs, please refer to the Technical Information chapter. Surface mounted installation. Mounting plate with two securing holes. Connection 3-way snap-in terminal block 2.5 mm², through-wiring possible. Cable entry from the top of the luminaire or via 3 knock-out openings, 90 or 180. Luminaire body in white (RAL 9016) cast aluminium. Reflector Reflector in either specular or matt anodised aluminium. Specular metallised Advanced Anti-Glare Control ring above the LED module. Mechanical shielding 45. Miscellaneous LED module includes ballast and can easily be replaced via a bayonet feature. downlights industrial system recessed pendant/surface Specular reflector Matt reflector LED module includes the ballast and can easily be changed using the bayonet mount. 249

28 523 Pleiad Wallwasher G3 LED module, W Colour temp, K Reflector 1100, Specular , Specular , Specular , Specular , Specular For current information on output and luminous flux, please refer to our website. Recessed mounting in unventilated or ventilated ceilings. The luminaire must not be covered with insulation. For further details please refer to the assembly instructions on our website. Separate ballast and installation clip for easy and tool-free installation supplied as standard. An assembly plate must be used when mounting on soft tile ceilings. Connection Connections are made to an independent LED ballast. The luminaire is delivered with the interconnecting cable with snap-in release in ballast. Luminaire body in black cast aluminium. Visible reflector ring in white PC plastic (RAL 9003). Reflector Metallised PBT in specular aluminium. The reflector has a protective coat of scratch-resistant clear lacquer. Miscellaneous The luminaire is supplied with dust protection over the light opening. Information LED luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 3000 K 80 L h MacAdam 3 SDCM 4000 K 80 L h MacAdam 3 SDCM For further information on LEDs, please refer to the Technical Information chapter. Suffix code -365 TouchDIM/DALI Add suffix code to the end of the luminaire part number to indicate required function. All versions t Max The reflector design delivers an even luminance across the surface, avoiding the traditional dark spots where the wall and ceiling meets. 250

29 523 Pleiad Robust G3 Pleiad Robust G3 SLD LED module, W Colour temp, K Luminous flux, lm/m Reflector 1100, Matt , Matt , Matt , Matt For current information on output and luminous flux, please refer to our website. Pleiad Robust G3 Compact LED module, W Colour temp, K Luminous flux, lm/m Reflector 1100, Matt , Matt , Matt , Matt For current information on output and luminous flux, please refer to our website. Information LED luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 3000 K 80 L h MacAdam 3 SDCM 4000 K 80 L h MacAdam 3 SDCM For more information on LEDs, see Technical Chapter. Suffix code -365 TouchDIM/DALI Add suffix code to the end of the luminaire part number to indicate required function. Recessed mounting in unventilated or ventilated ceilings. Assembly springs for quick, tool-free installation included. An assembly plate should be used when installing in soft tile ceilings. The ballast box can be detached for flexible installation. Connection Connections are made to an independent LED ballast. The luminaire is delivered with the interconnecting cable with snap-in release in ballast. Luminaire body in black cast aluminium. Two-part visible decor ring in aluminium. The luminaire has durable PEGT plates in the light openings between the rings. The luminaire and the rings are locked using tamper-proof torx screws. Reflector Reflector in matt anodised aluminium. Specular metallised Advanced Anti-Glare Control ring above the LED module. Miscellaneous The luminaire provides the highest mechanical protection beneath international classification IK10. Enclosure class IP 64 beneath suspended ceilings and IP 20 above suspended ceilings. Light source ordered separately. downlights industrial system recessed pendant/surface SLD Compact The light source is protected by a clear plastic PEGT plate which is held by an inner ring t Max The ring is mounted using tamperproof torx security screws. 251

30 Easy Easy is manufactured of cast aluminium and is extremely easy to install in most types of suspended ceilings. Available in white or alu-grey, there are three different designs; one fixed and two flexible. The flexible models can be angled adjusted through 0 90 or 0 30, both can be swivelled through 355. The light distribution for Easy depends on the choice of light source. The halogen lamp HRGI comes in various designs with several different distribution angles. Easy can be supplemented with a black baffle accessory to increase the mechanical cut-off angle. The LED and MV versions of Easy are the perfect alternative for halls, kitchens and bathrooms amongst other applications. The retrofit lamp offers great choice as the colour temperature and distribution angle can be easily changed. The fitting can also be adjusted from

31 DR HAGS GU10 Easy MV Luminaire DR HAGS Turn/Tilt White / For current information on output and luminous flux, please refer to our website. Information LED-Luminaire Colour temp. (CCT) Ra (CRI) Life Colour quality 2700 K 80 L h MacAdam 5 SDCM 3000 K 80 L h MacAdam 5 SDCM For further information on LEDs, please refer to the Technical Information chapter. Accessories Assembly plate Light source DR HAGS Light intensity, cd Socket Beam angle 2700 K 3000 K GU GU GU GU For further information please refer to the Light Sources chapter. Recessed mounting in unventilated ceilings. The luminaire must not be covered with insulation. For further details please refer to the assembly instructions on our website. Assembly springs for quick assembly included. The assembly plate should be used when mounting in soft ceilings, see accessories. Connection Connect to 230 V, terminal block with possible through-wiring. Max outer dimensions of the connection cable 5 8 mm. Luminaire body of cast aluminium. Assembly springs in spring steel. White (RAL 9016) structured. The luminaire tilts 30. Miscellaneous IP 21 applies under suspended ceilings. It can be dimmed using incandescent lamp dimmers. downlights industrial system recessed pendant/surface 230 V LED Light source. = Max 28 W Terminal block with strain relief and through-wiring possible. 305

32 Marathon Marathon is a stylish spotlight designed for track systems. Available in three different sizes its cylindrical shape and clean design makes Marathon a spotlight ideal for any setting. Produced in a dramatic black or subtle white finish, the luminaire housing and ballast are constructed of aluminium and the front ring of thermoplastic. Positioning the direction of Marathon is made easy, the luminaire can be turned through 360 and the luminaire housing can be angled The metal halogen versions are available with wide, medium and narrow beam, while the light distribution in the HRGI version is determined by the choice of light source. Marathon is supplied as standard with an electronic ballast. Marathon is now also available in several LED versions. The latest, Marathon Midi LED itrack, is a dimmable luminaire optimised for Fagerhult s itrack system. 318

33 523 Marathon Midi LED Fitted to 3-phase track or FixPoint bracket. Universal adapter 3-phase included. Luminaire in white (RAL 9010) or black (RAL 9005). Luminaire housing and ballast in extruded/cast aluminium. Baffle of thermoplastic. Reflector Metallised reflector. Miscellaneous Marathon can be turned through 355 and angled Active cooling. Luminaire LED module, lm, W Colour temp, K Luminous flux, lm Efficiency, lm/w kg White Black Narrow beam 1100, Medium beam 1100, , , , , Wide beam 1100, , , , , For current information on output and luminous flux, please refer to our website. Information LED luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 3000 K 80 L h MacAdam 3 SDCM 4000 K 80 L h MacAdam 3 SDCM For further information on LEDs, please refer to the Technical Information chapter. Narrow beam, 1100 lm Medium beam, 1100 lm Medium beam, 2000 lm Medium beam, 3000 lm Wide beam, 2000 lm Wide beam, 3000 lm Marathon Midi LED in white. 320

34 523 Marathon Midi LED itrack Luminaire LED module, lm, W Colour temp, K Luminous flux, lm Efficiency, lm/w kg White Black Narrow beam 1100, Medium beam 1100, , , , , Wide beam 1100, , , , , For current information on output and luminous flux, please refer to our website. Information LED luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 3000 K 80 L h MacAdam 3 SDCM 4000 K 80 L h MacAdam 3 SDCM For further information on LEDs, please refer to the Technical Information chapter. Fitted to itrack system. itrack adapter included. Luminaire in enamelled white (RAL 9010) or black (RAL 9005). Luminaire housing and ballast in extruded/cast aluminium. Baffle of thermoplastic. Reflector Metallised reflector. Dimming DALI as standard. Miscellaneous Marathon can be turned through 355 and angled Passive and active cooling. spotlights downlights industrial system recessed pendant/surface Narrow beam, 1100 lm Medium beam, 1100 lm Medium beam, 2000 lm Medium beam, 3000 lm Wide beam, 2000 lm Wide beam, 3000 lm lm 2000 lm lm Marathon Midi LED itrack in white. 319

35 Tibi ed by Olle Lundberg Tibi produces a crisp, radiant light, floating in the space with its distinct form. Its classical super ellipse shape is maximised with advanced LED technology to create a stunning light experience. Its extensive range includes ceiling and wall luminaires which have been optimised to use the most functional control system on the market. Careful consideration was paid towards the selection of materials and high quality LED units. Its distinctive, contemporary design units the rectangles surface efficiency with the circles aesthetic appeal. The even illuminance across the globe enhances the diffuser, constructed of smooth polished acrylic, reminiscent of glass. Tibi was developed as a complete luminaire family consisting of pendant, ceiling and wall variations. A suspended luminaire of 800 mm for large rooms is supported by pendant, ceiling and wall luminaires in two sizes 600 mm and 400 mm. All models are available with aluminium details in two finishes: brushed and clear lacquered aluminium or a polished, black lacquered surface. The ceiling and wall luminaires are ready for use with the wireless control system e-sense Move, which lights up each floor as and when someone enters. A perfect solution for stairwells Tibi pendant, see page Tibi ceiling, see page Tibi wall, see page

36 523 Tibi Pendant Luminaire System, W Colour temp., K Luminous flux, lm Efficiency, lm/w kg Brushed aluminium Black For current information on output and luminous flux, please refer to our website. Information LED-Luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 4000 K 80 L h MacAdam 4 SDCM For further information on LEDs, please refer to the Technical Information chapter. Accessories Cutters Two-point suspension, c/c mm. Connection Snap-in terminal block mm², 1-phase through-wiring possible. Wire length 2.5 m and a 2.5 m white fabric cord. Surface mounted cable possible. Height adjustment is done on the luminaire via a friction lock. Diffuser in specular opal acrylic. Luminaire body/decorative edge ring in aluminium. Decorative edge ring lacquered in glossy black (RAL 9005) or clear lacquered brushed aluminium. Colour-coordinated ceiling cup. Dimming DALI dimming as standard. Miscellaneous A cut-out in the ceiling cup is made using cutters for a surface mounted mains cable. ed by Olle Lundberg. architectural spotlights downlights industrial system recessed pendant/surface Excess wire is inserted into the void in the casting. 138/200/ /600/800 Colour-coordinated ceiling cup attached by magnet without visible screws. 349

37 Tibi Wall Luminaire System, W Colour temp., K Luminous flux, lm Efficiency, lm/w kg Brushed aluminium Black Other suffix code replaces For current information on output and luminous flux, please refer to our website. Information LED-Luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 4000 K 80 L h MacAdam 4 SDCM For further information on LEDs, please refer to the Technical Information chapter. Suffix code -439 e-sense Detect -440 e-sense Move Add suffix code to the end of the luminaire part number to indicate required function. Only one suffix can be added. Two securing holes for wall mounting. IP 40. IP 41 is available upon request. Connection Snap-in terminal block mm², 1-phase through-wiring possible. Cable entry from top of the luminaire. Surface mounted mains cable possible, through-wiring 180. Diffuser in specular opal acrylic. Luminaire body/decorative edge ring in aluminium. Decorative edge ring lacquered in glossy black (RAL 9005) or clear lacquered brushed aluminium. Dimming DALI dimming as standard. e-sense Detect microwave sensor for on/off function, or absence dimming with the option of switch-off function. e-sense Move wireless control between luminaires. Microwave sensor for the on/off function, or absence dimming with the option of switchoff function. For further information please refer to the dimming section in the Technical chapter. ed by Olle Lundberg. architectural spotlights downlights industrial system recessed pendant/surface 12/11 115/ / /435 Decorative edge ring lacquered in glossy black or clear lacquered brushed aluminium. 397

38 Tibi Ceiling Luminaire System, W Colour temp., K Luminous flux, lm Efficiency, lm/w Brushed aluminium Black Other suffix code replaces For current information on output and luminous flux, please refer to our website. Information LED-Luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 4000 K 80 L h MacAdam 4 SDCM For further information on LEDs, please refer to the Technical Information chapter. Suffix code -439 e-sense Detect absence dampening -440 e-sense Move absence dampening Add suffix code to the end of the luminaire part number to indicate required function. Only one suffix can be added. Two securing holes for ceiling installation. Protection class IP 41. Connection Snap-in terminal block mm², 1-phase through-wiring possible. Cable entry from top of the luminaire. Surface mounted mains cable possible, through-wiring 180. Diffuser in specular opal acrylic. Luminaire body/decorative edge ring in aluminium. Decorative edge ring lacquered in glossy black (RAL 9005) or clear lacquered brushed aluminium. Dimming DALI dimming as standard. e-sense Detect microwave sensor for absence dimming with the option of switch-off function. e-sense Move wireless control between luminaires. Microwave sensor for absence dimming with the option of switch-off function. For further information please refer to the dimming section in the Technical chapter. ed by Olle Lundberg. architectural spotlights downlights industrial system recessed pendant/surface 12/11 115/ / /435 The luminaire can also be mounted on wall. 375

39 D63 ed by Henning Solfeldt, PLH arkitekter Can a luminaire really be this small? With a diameter of just 63 mm, D63 is the perfect choice for conference rooms, corridor, cafes, restaurants and other applications which focus on furnishing and interior design. D63 is a complete luminaire family, consisting of pendant, ceiling and wall variations. The ceiling model is semi-recessed for an extra chic impression and is a new and fresh alternative to recessed spotlights. The wall luminaire is IP44 rated, lending itself bathroom, spar and relaxation environments, not to mention as an eye catching compliment above a mirror. The effective, glare-free LED unit defies its size with a generous output, while the opal acrylic louvre generates a crisp effect when lit D63 Pendant, see page D63 Ceiling, see page D63 Wall, see page

40 523 D63 Pendant Luminaire System, W Colour temp., K Luminous flux, lm Efficiency, lm/w For current information on output and luminous flux, please refer to our website. Two point suspension. Connection Connects with 230 V, built-in LED ballast in ceiling cup. Snap-in terminal block mm². Through-wiring possible. Surface mounted cable possible. Luminaire body in cast aluminium, structured grey (RAL 9006) finish. Diffuser in opal acrylic. Grey finish ceiling cup. Supplied with a 3 m white cable. Dimming Dimming possible using a trailing edge dimmer. Dimmable LED ballast as standard. Miscellaneous A cut-out in the ceiling cup is made using cutters for a surface mounted mains cable. ed by Henning Solfeldt, PLH Arkitekter. Information LED-Luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 3000 K 80 L h MacAdam 3 SDCM For further information on LEDs, please refer to the Technical Information chapter. Accessories Cutters/each Luminaire body in cast aluminium Colour-coordinated ceiling cup with integrated LED ballast. 370

41 523 D63 Ceiling Luminaire System, W Colour temp., K Luminous flux, lm Efficiency, lm/w For current information on output and luminous flux, please refer to our website. Information LED-Luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 3000 K 80 L h MacAdam 3 SDCM For further information on LEDs, please refer to the Technical Information chapter. Accessories Mounting plate for soft tile ceilings Semi-recessed in non-ventilated ceilings. Assembly springs for quick assembly included. The mounting plate should be used when mounting in soft tile ceilings, see accessories. Connection Connects with 230 V. LED ballast on mounting plate is placed above ceilings. Snap-in terminal block mm², through-wiring possible. Luminaire body in cast aluminium, grey (RAL 9006) structured finish. Diffuser in opal acrylic. Dimming Dimming possible using a trailing edge dimmer. Dimmable LED ballast as standard. ed by Henning Solfeldt, PLH arkitekter. architectural spotlights downlights industrial system recessed pendant/surface Mounting plate with LED ballast and terminal block with possible throughwiring is placed above ceilings t Max The diffuser produces light on the ceiling with good mechanical shielding. 387

42 523 D63 Wall Luminaire System, W Colour temp., K Luminous flux, lm Efficiency, lm/w For current information on output and luminous flux, please refer to our website. Information LED-Luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 3000 K 80 L h MacAdam 3 SDCM For further information on LEDs, please refer to the Technical Information chapter. Accessories Cutters/each On walls with two securing holes. Protection class IP 44. Connection Connects with 230 V, built-in LED ballast. Snap-in terminal block mm². Through-wiring possible. Cable entry on rear of the luminaire. Luminaire body in cast aluminium, structured grey (RAL 9006) finish. Diffuser in opal acrylic. Dimming Dimming possible using a trailing edge dimmer. Dimmable LED ballast as standard. architectural spotlights downlights industrial system recessed pendant/surface The luminaire provides a comfortable light and a glare-free LED module Luminaire body in cast aluminium with integrated LED ballast. 407

43 Discovery ed by Wilma Daemen The round beam Discovery family is ideal for many areas of application. The smaller Discovery is complemented by Discovery Space, a slightly larger version constructed of the same materials to maintain the robust design. The range has now been further expanded to include an LED version, offering even greater efficiency. Both sizes can be surface and semi-recessed mounted. Surface mounting gives a decorative trailing light on the wall. Accessories expand the range further and add a decorative touch to this type of luminaire. Please note that the accessories only fit Discovery. architectural spotlights downlights industrial system recessed pendant/surface Discovery, see page Discovery Space, see page Discovery Space LED, see page

44 523 Discovery Space LED Luminaire System, W Colour temp., K Luminous flux, lm Efficiency, lm/w kg Acrylic PC For current information on output and luminous flux, please refer to our website. Information LED-Luminaire Colour temp, (CCT) Ra (CRI) Life Colour quality 3000 K 80 L h MacAdam 4 SDCM For further information on LEDs, please refer to the Technical Information chapter. Suffix Code -219 e-sense smartswitch on/off V -357 e-sense Detect on/off -439 e-sense Detect absence dampening -431 e-sense Move on/off -440 e-sense Move absence dampening Add suffix code to the end of the luminaire part number to indicate required function. Only one suffix can be added. Four fixing holes. Surface mounted or semi-recessed on ceilings or walls. Brackets for recessed installation ordered separately, please see accessories. Connection Snap-in terminal block mm², 3-phase through-wiring possible. Surface mounted mains cable possible, through-wiring 0 or 180. Three 16 mm cable entries fitted with blanking grommets on the top of the luminaire. Polycarbonate luminaire body and impact resistant acrylic or polycarbonate diffuser. Accessories Trim ring and outer casing in white or grey (RAL 9006) aluminium. Robust case of cast aluminium. An aluminium ring seals tight against the ceiling or wall. Four security screws (tamper-proof torx) IP 65. IK10 in PC. Dimming e-sense smartswitch luminaire with PIR sensor for presence detection on/off. IP 43 in ceiling, IP 20 on wall. e-sense Detect microwave sensor for on/off function, or absence dimming with the option of switch-off function. e-sense Move wireless lighting control between luminaires. Microwave sensor for on/off function, or absence dimming with the option of switch-off function. ed by Wilma Daemen. Accessories Recess brackets, 4 pcs Diffuser lock/10 pcs. (1 per luminaire) Decor casing, white Robust case gives IP 65, white (IK10 with PC-diffuser) Robust Robust case of cast aluminium with security screws. 390

45 emled Fagerhult s emled concept builds on a high intensity LED which is only used for emergency lighting. The LED almost never wears out since it is only used in emergency mode and when the test sequences are run. The concept increases personal safety considerably by almost eliminating the risk of the emergency light failing to work. In a traditional solution, where the same light source is used in normal operation and emergency mode, there is a risk that the light source may have burned out or ceased to operate when a crisis situation arises. emled exists as a stand-alone unit in several different designs. emled-s2, -s4, -s5 and -sc where the same unit is used for both surface mounted and recessed installation. emled-μ is a unit for recessed installation where the ballast and batteries are concealed above the ceiling and only the LED visible. During a power failure the emled-s2, -s4, -s5 and -μ are operated by integrated batteries and emled-sc is operated by a centrally connected emergency lighting system. architectural spotlights downlights industrial system recessed pendant/surface emergency 427

46 523 emled-s2, emled-s4, emled-s5 Luminaire kg Monitoring via emled-s2 0.3 Potential free contact emled-s4 0,3 Potential free contact emled-s5 0.3 DALI emled-s4 and -s5 are versions with higher luminous flux in emergency mode. Can be fitted with a longer c/c compared to emled-s2 (see table in the introduction). Wiring diagram overview Live 1 Neutral Protective earth Monitor Monitor I/O m.m. 24 VDC (min 30 ma) + C NC There is a relay module, 98158, used when a large number of emled-s2 or emled-s4 connected in monitoring systems. The relay module, should be connected to an external voltage source of 2 VV DC and is designed for mounting on DIN-rails and has a 1-module width. 103,5 Accessories Spare battery Assembly plate for soft tile ceiling Relay module emled-s Optional either surface or recessed mounting in ventilated or unventilated areas. c/c between securing holes is optional 38, 55, 60, 67 and 78 mm. Recessed mounting requires a ceiling thickness of between 5 and 25 mm. Connection Phase, neutral conductor protective earth and monitoring cables. Equipped as standard with a 2 way output for the connection of the master system based on the detection of potential free contact (NC) or communication via DALI. All connections are gathered in the luminaire body in a snap-in, 6-way terminal block. The detachable lower section housing the electronics and battery where applicable is connected to the terminal block in the luminaire body with a plug-in connection. Through-wiring of 2.5 mm² cable is possible (all positions) mm cable entries fitted with blanking grommets on the top. Strain relief for movable cables with recess mounting supplied. For 230 V AC 50/60 Hz. Enclosure class IP 40, protection class I. Plastic parts of PC/ABS plastic. Spring clips for recess mounting made of stainless spring steel. NiMH battery and two-colour (green/red) status diodes. Equipped with self-test as standard (Autotest IV, see separate section) equivalent to standard EN and with the possibility of external monitoring either via a potential free contact or DALI dependent on product selection. Equipped with test button for manually starting the short function test. Miscellaneous Decentralised emergency light function, 3 hours operation in emergency lighting mode. White LED only works in emergency mode (non-maintained). The product conforms to the requirements set out in IEC test FC and IEC test Fh and DNV Cert. Notes No.2.4 April 2006, with requirements including made on products intended for marine use or other environments where the risk of vibrations. Some monitoring systems based on the detection of potential free contact can be sensitive to signal purity. When a large number of emled-s2 or emled-s4 are connected to a monitoring system an emled relay module, 98158, is required. The relay module is connected to an external voltage source, 2VV DC, and is designed to be mounted on DIN-rails and has a 1 module width. emergency architectural spotlights downlights industrial system recessed pendant/surface ,