NAMES OF PARTS. 1 Thread guide for bobbin winding 2 Take-up lever. 3 Upper thread tension dial. 4 Face cover. 5 Thread guide for upper threading

Transcription

1 6 Presser foot thumb screw 9 Spool pins (retractable) 8 Shuttle cover 5 Thread guide for upper threading 7 Presser foot 4 Face cover NAMES OF PARTS.r4r : VjN S* ;WWE MODEL : PART NO Needle plate 24 Feed dog 22 Thread cutter 20 Thread guide for upper threading 19 Socket 1 7 Handwheel 1 8 Stop motion knob 16 Bobbin winding stop 1 5 Bobbin winding spindle 21 Presser foot lifter 1 2 Zigzag width control 1 3 Accessory box ii Stitch length dial 10 Reverse sewing button 14 Free arm 3 Upper thread tension dial 1 Thread guide for bobbin winding 2 Take-up lever

2 bobbin comes out easily. Close latch of bobbin case and Set needle in the highest through thread guide and pre take it out. Draw thread from spool pin Open shuttle cover. Open latch of bobbin case and Put a spool on spool pin. towards you. position by turning handwheel Bobbin Winding BEFORE SEWING unscrewing stop motion knob. hand disengage handwheel by Holding handwheel with your left Wind thread clockwise around Push bobbin on to spindle. bobbin several times. ers I 2 and. tension device, following numb I till SSUto 1d F

3 down foot controller. when winding is full. Retighten stop motion knob. loosen set-screw of the guide for bobbin winding, by using screw driver and adjust height. trobie as shown, open face cover and If bobbin is wound unevenly / / and cut thread. bobbin case. Machine stops automatically Take off bobbin from spindle Push bobbin to right and press Push bobbin to left. arrow. thread running in direction of Place bobbin in its case with Inserting Bobbin I correct,or, delivery eye c. under tension spring then to Pulling thread to left, bring it Guide thread into slot. of

4 Leave end of thread of about 10 Leave end of thread of about 1 5 is fully inserted. Take hold of latch and push Release latch when bobbin case bobbin case into hook. cm (4 ) from bobbin case. position. Raise needle in the highest screw with small screwdriver. will gradually drop a small At proper tension bobbin case shake bobbin case as shown, amount. To test bobbin tension, hang and To adjust tension, turn adjusting Thread following numbers L- 7. upwards. Thread take-up lever 4. disc. Lead thread either side of tensfon towards you. I] Pass thread through guide (Lj. joosen / qhter Adjusting Lower Tension i nreaaing upper i nredu cm (6 ). Pass thread to guide () from right to left, and guide (left one) then needle eye D. Hook it to guide from down to position by turning handwheel Raise take-up lever to the highest Raise presser foot lifter.

5 you until needle moves down and up again. Turn handwheel slowly towards left hand. Hold end of upper thread with position by turning handwheel Loosen needle clamp screw and hook and needle plate. under presser foot on left. cm (6 ) and place them together Pull upper thread slowly and Pull out both threads to about 1 5 in a loop. of needle bar. of thread; it also can damage Push needle until it reaches lower thread will be brought up insert a new needle into groove With flat face away from you, remove needle. towards you. breakage of needles or snapping Always use a straight needle with Using defective or worn needles a sharp point. clamp screw firmly. not only causes stitch skipping, straight shaft sharp point Proper needle stopper and tighten needle Set needle in the highest Drawing Up Lower Thread Changing Needle

6 STRAIGHT SEWING Set machine as shown. Place fabric under foot about 1 cm (0.4 ) inside the edge. Lower presser foot lifter. Double Presser Foot Lifter In order to obtain wider gap when using very thick materials, firmly push presser foot lifter up as far as it will go. L,.. rt Stitch Length Dial Set dial at indicating point according to stitch size required. For a longer stitch, turn dial downwards. For a shorter stitch, turn it upwards. p. To reinforce seam, sew back wards to the edge of fabric by pushing reverse sewing button. For normal sewing it is set between 2 and 3. Release button and commence forward sewing guiding fabric by hand as it is fed. Never pull material.

7 Sew reverse stitches for rein forcement at end of seam. Draw fabric to left when sewing is finished ZIGZAG SEWING Set machine as shown. To prevent seam ends unravell ing, set machine for straight stitch and sew in reverse at beginning and ending of seam. Cut threads with thread cutter behind presser bar. Adjusting Thread Tension i-nh Zigzag Width Control Set control at required number. Larger the number, wider the stitch. Set it at 0 for straight sewing. Make sure needle is in upper position when you set control. upper tension too tight upper tension too nose 5F. a Test stitch performance on a scrap of material you are going to use. With correct tension (), upper and lower threads tension is equal and strong enough to lock both threads in center. If upper tension is too tight floose), upper (lower) thread lies straight along upper (lower) surface of fabric Correct by turning tension dial. Thread Tension for Zigzag Stitch Better-looking zigzag stitching requires less upper tension than straight stitching. Loosen upper tension slightly.

8 c Remove foot and needle. dog with cleaning brush. cloth. with a cleaning brush and a soft Remove needle plate. Remove hook race cover. Remove hook. Clean hook race of oil to lubricating Turn latches outwards. Brush off all dust and lint on feed Cleaning cleaned and oiled once a month. few hours a day needs to be Apply one drop of oil to part of A machine which is used for a factory sewing performance. mechanism to jam. loosening screws and Apply one drop points indicated by arrows. Remove top cover by minutes to allow oil to penetrate to every part. After oiling, run machine for 1-2 oil or it may stain your material Be careful not to apply too much the same way. Open face cover and apply oil in cleaning and oiling for satis hook where friction occurs. and cause some sewing difficulty. 7 j oils will eventually cause N Your machine requires regular for sewing machine use. Other \ Use oil manufactured specially MAINTENANCE Oiling