Nederlandse norm. NEN-ISO (en) Specification for diagrams for process industry - Part 1: General rules (ISO :2010,IDT)

Transcription

1 Dit document mag slechts op een stand-alone PC worden geinstalleerd. Gebruik op een netwerk is alleen. toestaan als een aanvullende licentieovereenkomst voor netwerkgebruik met NEN is afgesloten. This document may only be used on a stand-alone PC. Use in a network is only permitted when a supplementary license agreement for us in a network with NEN has been concluded. Nederlandse norm NEN-ISO (en) Specification for diagrams for process industry - Part 1: General rules (ISO :2010,IDT) ICS ; maart 2010

2 NEN-ISO Als Nederlandse norm is aanvaard: - ISO :2010,IDT Normcommissie "Technische Productdocumentatie" Apart from exceptions provided by the law, nothing from this publication may be duplicated and/or published by means of photocopy, microfilm, storage in computer files or otherwise, which also applies to full or partial processing, without the written consent of the Netherlands Standardization Institute. The Netherlands Standardization Institute shall, with the exclusion of any other beneficiary, collect payments owed by third parties for duplication and/or act in and out of law, where this authority is not transferred or falls by right to the Reproduction Rights Foundation. Auteursrecht voorbehouden. Behoudens uitzondering door de wet gesteld mag zonder schriftelijke toestemming van het Nederlands Normalisatie-instituut niets uit deze uitgave worden verveelvoudigd en/of openbaar gemaakt door middel van fotokopie, microfilm, opslag in computerbestanden of anderszins, hetgeen ook van toepassing is op gehele of gedeeltelijke bewerking. Het Nederlands Normalisatie-instituut is met uitsluiting van ieder ander gerechtigd de door derden verschuldigde vergoedingen voor verveelvoudiging te innen en/of daartoe in en buiten rechte op te treden, voor zover deze bevoegdheid niet is overgedragen c.q. rechtens toekomt aan de Stichting Reprorecht. Although the utmost care has been taken with this publication, errors and omissions cannot be entirely excluded. The Netherlands Standardization Institute and/or the members of the committees therefore accept no liability, not even for direct or indirect damage, occurring due to or in relation with the application of publications issued by the Netherlands Standardization Institute. Hoewel bij deze uitgave de uiterste zorg is nagestreefd, kunnen fouten en onvolledigheden niet geheel worden uitgesloten. Het Nederlands Normalisatie-instituut en/of de leden van de commissies aanvaarden derhalve geen enkele aansprakelijkheid, ook niet voor directe of indirecte schade, ontstaan door of verband houdend met toepassing van door het Nederlands Normalisatie-instituut gepubliceerde uitgaven Nederlands Normalisatie-instituut Postbus 5059, 2600 GB Delft Telefoon (015) , Fax (015)

3 INTERNATIONAL STANDARD ISO First edition Specification for diagrams for process industry Part 1: General rules Spécifications pour schémas de l'industrie de traitement Partie 1: Règles générales Reference number ISO 2010

4 PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel Fax copyright@iso.org Web Published in Switzerland ii ISO 2010 All rights reserved

5 Contents Foreword...v Introduction...vi 1 Scope Normative references Terms and definitions Basic terms Document types Reference designation Documentation principles General Technical product documentation Representation aspects Focus area in this part of ISO Document sheets General Identification area Content areas Lines Types of line Width of lines Space between lines Leader lines and reference lines Reference designations Introduction General Boundary frames Transition Objects in a sheet Port designations Location references Technical data and explanatory notes Components and devices Flow paths Explanatory notes Supplementary diagram symbols Graphical symbols General Creation of new symbol examples Features of symbols Use of symbols in diagrams Connections General Significant connections Simplified representation Joints Intersections...27 Page ISO 2010 All rights reserved iii

6 12.6 References for interrupted connecting lines Objects with two or more system connections Layout of diagrams General aspect Functional layout Topographical layout Types of diagram General Overview diagrams Function diagrams...31 Annex A (informative) Diagram symbols...34 Annex B (informative) Document type designation and content of information...35 Bibliography...37 iv ISO 2010 All rights reserved

7 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO was prepared by Technical Committee ISO/TC 10, Technical product documentation, Subcommittee SC 10, Process plant documentation and tpd-symbols. ISO consists of the following parts, under the general title Specification for diagrams for process industry: Part 1: General rules ISO 2010 All rights reserved v

8 Introduction This part of ISO deals with preparation of diagrams and associated documents and data for process industry. Together with rules for the preparation of diagrams and associated documents and data, this part of ISO includes rules and recommendations for the application of associated standards in diagrams, for example graphical symbols and reference designation. The following diagram gives an overview of interrelations between these standards. Graphical symbols In this part of ISO references are made to symbols and rules in the ISO series by using registration numbers. Three types of registration number are used in ISO 14617: 101 registration number for a symbol; R101 registration number for an application rule; X101 registration number for an application example. When reference is made to ISO 14617, the description is in italics, e.g. Symbol 255: Circular motion. Cross-references to referred symbols, rules and examples in the ISO series can be found in the registration number index in ISO Collective application standards Technical committees, requiring a field specific standard, are allowed, in co-operation with ISO/TC 10, to develop their own collective application standard for preparation of diagrams in accordance with the rules given in this part of ISO Application standards should not be contradictory with respect to this source standard. Figures Figures in this part of ISO are only examples for illustration of a given rule. vi ISO 2010 All rights reserved

9 INTERNATIONAL STANDARD Specification for diagrams for process industry Part 1: General rules 1 Scope This part of ISO provides general rules and guidelines for the preparation and presentation of information in diagrams for process industry. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO Technical drawings General principles of presentation Part 20: Basic conventions for lines ISO , Technical drawings General principles of presentation Part 21: Preparation of lines by CAD systems ISO , Technical drawings General principles of presentation Part 22: Basic conventions and applications for leader lines and reference lines ISO , Technical product documentation Lettering Part 0: General requirements ISO , Technical product documentation Lettering Part 5: CAD lettering of the Latin alphabet, numerals and marks ISO 5457, Technical product documentation Sizes and layout of drawing sheets ISO 6428, Technical drawings Requirements for microcopying ISO 7200, Technical product documentation Data fields in title blocks and document headers ISO (all parts), Graphical symbols for diagrams ISO/TS , Technical product documentation Reference designation system Part 1: General application rules ISO (all parts), Quantities and units ISO :1999, Design of graphical symbols for use in the technical documentation of products Part 1: Basic rules IEC , Design of graphical symbols for use in the technical documentation of products Part 2: Specification for graphical symbols in a computer sensible form, including graphical symbols for a reference library, and requirements for their interchange ISO 2010 All rights reserved 1

10 Bestelformulier Stuur naar: NEN Standards Products & Services t.a.v. afdeling Klantenservice Antwoordnummer WB Delft NEN Standards Products & Services Postbus GB Delft Vlinderweg AX Delft Ja, ik bestel ex. en Specificatie voor schema's voor procesindustrie - Deel 1: Algemene regels T (015) F (015) Wilt u deze norm in PDF-formaat? Deze bestelt u eenvoudig via Gratis nieuwsbrieven Wilt u op de hoogte blijven van de laatste ontwikkelingen op het gebied van normen, normalisatie en regelgeving? Neem dan een gratis abonnement op een van onze nieuwsbrieven. Gegevens Bedrijf / Instelling T.a.v. O M O V Klantnummer NEN Uw ordernummer BTW nummer Postbus / Adres Postcode Plaats Telefoon Fax Factuuradres (indien dit afwijkt van bovenstaand adres) Postbus / Adres Postcode Plaats Datum Handtekening Retourneren Fax: klantenservice@nen.nl Post: NEN Standards Products & Services, t.a.v. afdeling Klantenservice Antwoordnummer 10214, 2600 WB Delft (geen postzegel nodig). Voorwaarden De prijzen zijn geldig tot 31 december 2018, tenzij anders aangegeven. Alle prijzen zijn excl. btw, verzend- en handelingskosten en onder voorbehoud bij o.m. ISO- en IEC-normen. Bestelt u via de normshop een pdf, dan betaalt u geen handeling en verzendkosten. Meer informatie: telefoon , dagelijks van 8.30 tot uur. Wijzigingen en typefouten in teksten en prijsinformatie voorbehouden. U kunt onze algemene voorwaarden terugvinden op: LEREN, WERKEN EN GROEIEN MET NEN preview