Nederlandse norm NEN-ISO (en) Gears - Cylindrical involute gears and gear pairs - Concepts and geometry (ISO 21771:2007,IDT)

Transcription

1 Dit document mag slechts op een stand-alone PC worden geinstalleerd. Gebruik op een netwerk is alleen. toestaan als een aanvullende licentieovereenkomst voor netwerkgebruik met NEN is afgesloten. This document may only be used on a stand-alone PC. Use in a network is only permitted when a supplementary license agreement for us in a network with NEN has been concluded. Nederlandse norm NEN-ISO (en) Gears - Cylindrical involute gears and gear pairs - Concepts and geometry (ISO 21771:2007,IDT) ICS september 2007

2 NEN-ISO Als Nederlandse norm is aanvaard: - ISO 21771:2007,IDT Normcommissie "Tandwielen" Apart from exceptions provided by the law, nothing from this publication may be duplicated and/or published by means of photocopy, microfilm, storage in computer files or otherwise, which also applies to full or partial processing, without the written consent of the Netherlands Standardization Institute. The Netherlands Standardization Institute shall, with the exclusion of any other beneficiary, collect payments owed by third parties for duplication and/or act in and out of law, where this authority is not transferred or falls by right to the Reproduction Rights Foundation. Auteursrecht voorbehouden. Behoudens uitzondering door de wet gesteld mag zonder schriftelijke toestemming van het Nederlands Normalisatie-instituut niets uit deze uitgave worden verveelvoudigd en/of openbaar gemaakt door middel van fotokopie, microfilm, opslag in computerbestanden of anderszins, hetgeen ook van toepassing is op gehele of gedeeltelijke bewerking. Het Nederlands Normalisatie-instituut is met uitsluiting van ieder ander gerechtigd de door derden verschuldigde vergoedingen voor verveelvoudiging te innen en/of daartoe in en buiten rechte op te treden, voor zover deze bevoegdheid niet is overgedragen c.q. rechtens toekomt aan de Stichting Reprorecht. Although the utmost care has been taken with this publication, errors and omissions cannot be entirely excluded. The Netherlands Standardization Institute and/or the members of the committees therefore accept no liability, not even for direct or indirect damage, occurring due to or in relation with the application of publications issued by the Netherlands Standardization Institute. Hoewel bij deze uitgave de uiterste zorg is nagestreefd, kunnen fouten en onvolledigheden niet geheel worden uitgesloten. Het Nederlands Normalisatie-instituut en/of de leden van de commissies aanvaarden derhalve geen enkele aansprakelijkheid, ook niet voor directe of indirecte schade, ontstaan door of verband houdend met toepassing van door het Nederlands Normalisatie-instituut gepubliceerde uitgaven Nederlands Normalisatie-instituut Postbus 5059, 2600 GB Delft Telefoon (015) , Fax (015)

3 INTERNATIONAL STANDARD ISO First edition Gears Cylindrical involute gears and gear pairs Concepts and geometry Engrenages Roues et engrenages cylindriques à développante Concepts et géométrie Reference number ISO 2007

4 PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel Fax copyright@iso.org Web Published in Switzerland ii ISO 2007 All rights reserved

5 Contents Foreword... iv 1 Scope Normative references Symbols, subscripts and units Symbols Subscripts Units Individual cylindrical gears Concepts for an individual gear Reference surfaces, datum lines and reference quantities Involute helicoids Angular pitch and pitches Diameters of gear teeth Gear tooth height Tooth thickness, space width Cylindrical gear pairs Concepts for a gear pair Mating quantities Calculation of the sum of the profile shift coefficients Tooth engagement Backlash Sliding conditions at the tooth flanks Tooth flank modifications Tooth flank modifications which restrict the usable flank Transverse profile modifications Flank line (helix) modifications Flank face modifications Descriptions of modifications by functions Geometrical limits Counterpart rack tooth profile Machining allowance Deviations in tooth thickness Generating profile shift, generating profile shift coefficient Generated root diameter Usable area of the tooth flank, tip and root form diameter Undercut Overcut Minimum tooth thickness at the tip circle of a gear Annex A (informative) Calculations related to tooth thickness Bibliography Page ISO 2007 All rights reserved iii

6 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO was prepared by Technical Committee ISO/TC 60, Gears, Subcommittee SC 1, Nomenclature and wormgearing. This first edition of ISO cancels and replaces ISO/TR 4467:1982, of which it constitutes a technical revision. iv ISO 2007 All rights reserved

7 INTERNATIONAL STANDARD Gears Cylindrical involute gears and gear pairs Concepts and geometry 1 Scope This International Standard specifies the geometric concepts and parameters for cylindrical gears with involute helicoid tooth flanks. Flank modifications are included. It also covers the concepts and parameters for cylindrical gear pairs with parallel axes and a constant gear ratio, which consist of cylindrical gears according to it. Gear and mating gear in these gear pairs have the same basic rack tooth profile. The equations given are not restricted to the pressure angle, 20. The standard is structured as follows. Listing of symbols and nomenclature for a unique description of gears and gear pairs (see Clause 3). Equations and explanations of the relevant values for defining a cylindrical gear and its tooth system. The equations for determination of the nominal values for zero-deviation gear description parameters are stated for radial tooth dimensions (gear tooth heights), the distance between flanks of the same hand, the distance between flanks of opposite hand, as well as the tooth flank characterizing parameters (see Clause 4). Equations and explanations of the relevant values for defining cylindrical gear pairs. The equations for the essential parameters characterizing the engagement conditions of the unloaded gear pair are listed (see Clause 5). Equations and suggestions for desired flank modifications (see Clause 6). Concepts and recommendations needed for a unique geometrical definition of the intended results from manufacture (Clause 7). Equations for determination of the nominal values or the limiting values for the most used inspection methods for tooth thickness (see Annex A). P 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 53:1998, Cylindrical gears for general and heavy engineering Standard basic rack tooth profile ISO :1995, Cylindrical gears ISO system of accuracy Part 1: Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth ISO :1997, Cylindrical gears ISO system of accuracy Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information ISO 2007 All rights reserved 1

8 3 Symbols, subscripts and units 3.1 Symbols Symbol Description Used in a w centre distance of a cylindrical gear pair a 0 centre distance in the generating gear unit 7.5 a L centre distance for tooth flank engagement A.8 b facewidth b F usable facewidth b M contact line overlap (for measuring base tangent length) A.2.1 b w active facewidth (the facewidth used) c tip clearance c F form over dimension d reference diameter d a tip diameter d a0 tip diameter of tool 7.5 d am tip diameter of overcut cylindrical gears A.9 d b base diameter d b0 base diameter of the pinion-type cutter 7.6 d f root diameter (nominal dimension) d fe root diameter produced 7.5 d f0 root diameter of the pinion-type cutter A.9 d v V-circle diameter d w working pitch diameter d y Y-circle diameter d Fa tip form diameter 7.6 d Fa0 tip form diameter of the pinion-type cutter 7.6 d Ff root form diameter 7.6 d K diameter of circle through centre of ball A.5 d M diameter of a measuring circle A.2.1 d Na active tip diameter d Nf start of active profile diameter (SAP diameter, active root diameter) e t space width on the reference cylinder e yt space width on the Y-cylinder ISO 2007 All rights reserved

9 Symbol Description Used in e P space width of the standard basic rack tooth profile g a length of addendum path of contact g f length of dedendum path of contact g length of path of contact g y distance of a point Y from pitch point C g arc of contact h tooth depth (between tip line and root line) h a addendum h ap addendum of the standard basic rack tooth profile Figure 4 h ap0 addendum of the tool standard basic rack tooth profile 7.5 h f dedendum h fp dedendum of the standard basic rack tooth profile Figure 4 h fp0 dedendum of the tool standard basic rack tooth profile A.9 h w working depth of teeth in a gear pair h FfP depth of dedendum form of the standard basic rack tooth profile Figure 4 h K radius of the tip corner chamfering or tip corner rounding h P tooth depth of standard basic rack tooth profile Figure 4 inv involute function j bn contact backlash 5.5 j r radial backlash 5.5 j t circumferential backlash at the reference circle j wt circumferential backlash at the pitch circle 5.5 k number of teeth, spaces or pitches in a span (e.g. number of teeth spanned) A.2.1 k addendum modification coefficient l max path of engagement l sum of path of contact m n normal module m t transverse module m x axial module n a number of revolutions of driving gear (rpm) n b number of revolutions of driven gear (rpm) p pitch, pitch on the reference cylinder Figure 4 ISO 2007 All rights reserved 3

10 Symbol Description Used in p bn normal pitch on the base cylinder p bt transverse pitch on the base cylinder p en normal base pitch on the path of contact p et transverse base pitch on the path of contact p n normal pitch p t transverse pitch p x axial pitch p yn normal pitch on the Y-cylinder p yt transverse pitch on the Y-cylinder p z lead q machining allowance on tooth flank 7.2 q Fs undercut Figure 24 s ak residual tooth thickness at tip with tip corner chamfering or tip corner rounding s bn normal tooth thickness on the base circle A.2.2 s n normal tooth thickness on the reference circle s ni minimum normal tooth thickness on the reference circle 7.3 s ns maximum normal tooth thickness on the reference circle 7.3 s t transverse tooth thickness on the reference circle s yn normal tooth thickness on the Y-cylinder s yt transverse tooth thickness on the Y-cylinder s P tooth thickness of the standard basic rack tooth profile u gear ratio v g sliding speed v ga sliding speed at the addendum v gf sliding speed at the dedendum v n normal speed x profile shift coefficient x E generating profile shift coefficient 7.4 x Emin generating profile shift coefficient at undercut limit 7.7 x L profile shift coefficient of master gear A.8 z number of teeth z a number of teeth of driving gear ISO 2007 All rights reserved

11 Symbol Description Used in z b number of teeth of driven gear z L number of teeth of master gear A.8 z 0 number of teeth of pinion-type cutter 7.6 A starting point of meshing B starting point of single tooth contact on driving gear C pitch point, depth of relief for modifications C ay modification of the profile 6.5 C y modification of the flank line 6.5 C y modification of the flank surface 6.5 C a amount of tip relief C f amount of root relief C Ea tip amount of triangular end relief modification C Ef root amount of triangular end relief modification C i,j amount of modification at point (i,j) C H amount of transverse profile slope modification C amount of profile crowning (barrelling) C I, C li amount of end relief C amount of flank line crowning C H amount of flank line slope modification D M measuring ball or measuring cylinder diameter A.5 D end point of single tooth contact point on driving gear E end point of meshing E sn normal tooth thickness deviation limit (or allowance) A.9 E sni lower deviation limit for tooth thickness 7.3 E sns upper deviation limit for tooth thickness 7.3 K g sliding factor K ga sliding factor at tooth tip K gf sliding factor at tooth root L AE roll length 6.2 L Ca tip relief roll length L Cf root relief roll length L Cl, L ClI length of end relief L Ea tip roll length of triangular end relief modification ISO 2007 All rights reserved 5

12 Symbol Description Used in L Ef root roll length of triangular end relief modification M dk dimension over balls A.7 M dz dimension over cylinders A.7.1 M rk radial single-ball dimension A.5 M rz radial single-cylinder dimension A.6 N number of tooth or pitch O centre of a circle Figure 10 S twist of the transverse profile S twist of the flank line T sn tooth thickness tolerance Figure 37 T contact point of tangent (lines of engagement) at base circle Figure 10 U involute point of origin W k base tangent length over k measured teeth or measured spaces A.2.1 Y any point on a tooth flank or involute n normal pressure angle t transverse pressure angle wt working transverse pressure angle of gear pair wt0 working transverse pressure angle in the generating gear unit 7.6 yn normal pressure angle at the Y-cylinder yt transverse pressure angle at the Y-cylinder Ff pressure angle at root form circle 7.6 K pressure angle at circle through centre of ball A.5 Kt transverse pressure angle at a point at circle through centre of ball A.5 Mt transverse pressure angle at a point at measuring circle A.5 P pressure angle of the standard basic rack tooth profile P0 pressure angle of the tool basic rack tooth profile 7 L working transverse pressure angle for double-flank engagement A.8 vt transverse pressure angle at the V-cylinder A.5 helix angle b base helix angle y helix angle at Y-cylinder w angle of rocking for span measurement A ISO 2007 All rights reserved

13 Bestelformulier Stuur naar: NEN Standards Products & Services t.a.v. afdeling Klantenservice Antwoordnummer WB Delft NEN Standards Products & Services Postbus GB Delft Vlinderweg AX Delft Ja, ik bestel ex. en Tandwielen - Cilindrische evolvente tandwielen en tandwielparen - Concepten en geometrie T (015) F (015) Wilt u deze norm in PDF-formaat? Deze bestelt u eenvoudig via Gratis nieuwsbrieven Wilt u op de hoogte blijven van de laatste ontwikkelingen op het gebied van normen, normalisatie en regelgeving? Neem dan een gratis abonnement op een van onze nieuwsbrieven. Gegevens Bedrijf / Instelling T.a.v. O M O V Klantnummer NEN Uw ordernummer BTW nummer Postbus / Adres Postcode Plaats Telefoon Fax Factuuradres (indien dit afwijkt van bovenstaand adres) Postbus / Adres Postcode Plaats Datum Handtekening Retourneren Fax: klantenservice@nen.nl Post: NEN Standards Products & Services, t.a.v. afdeling Klantenservice Antwoordnummer 10214, 2600 WB Delft (geen postzegel nodig). Voorwaarden De prijzen zijn geldig tot 31 december 2018, tenzij anders aangegeven. Alle prijzen zijn excl. btw, verzend- en handelingskosten en onder voorbehoud bij o.m. ISO- en IEC-normen. Bestelt u via de normshop een pdf, dan betaalt u geen handeling en verzendkosten. Meer informatie: telefoon , dagelijks van 8.30 tot uur. Wijzigingen en typefouten in teksten en prijsinformatie voorbehouden. U kunt onze algemene voorwaarden terugvinden op: LEREN, WERKEN EN GROEIEN MET NEN preview