C Demonstrate understanding of common numerical methods and how they are used to obtain approximate solutions. C201.5

Transcription

1 COURSE OUTCOMES Engineering Mathematics-III (NAS-301): C201 Year of Study: Demonstrate the ability to integrate knowledge and ideas of complex differentiation and C201.1 complex integration in a coherent and meaningful manner and use appropriate techniques for solving related problems and for establishing theoretical results. C201.2 Acquire knowledge about fourier transform and Z transform. C201.3 Impart knowledge of testing of hypothesis for all size of sample and also gives the knowledge of finding out the coeffecient of correlation, regression line equation which can be used in project and research work. C201.4 Provides different methods to solve algebraic and transcendental equation C201.5 Demonstrate understanding of common numerical methods and how they are used to obtain approximate solutions. Fluid Mechanics (NCE-301): C202 Year of Study: The students will be able to convert units of any parameter between three systems of units, C202.1 understand the physical properties and characteristic behaviour of fluids, and the basic principles of fluid mechanics. Be able to describe and interpret the behaviour and performance of fluid at rest. C202.2 The students will be able to describe and interpret the behaviour and performance of fluid in motion. Be able to derive the dimensions of different fluid parameters. C202.3 The students will be able to apply Bernoulli equation. To apply similitude and modelling principles and techniques to solve problems in hydraulics. C202.4 The students will be able to describe the behaviour and performance of fluid when the fluid is flowing through the pipe. C202.5 The students will be able to understand concept of boundary layer, drag and lift. An introduction of magnus effect. Material Science (NME-301): C203 Year of Study: An understanding of the importance of materials, general principles and nomenclature of C203.1 crystallography as applied to engineering materials. To identify the microstructural based dependencies on mechanical properties of engineering C203.2 materials and mechanical failure, including yielding, fracture, fatigue, and creep; and apply these principles to design and process failure-resistant materials. An understanding of different types of ferrous and non-ferrous materials and the ability to C203.3 predict the effect of the rate of heat transport on the heat treatment and solidification of materials. A basic understanding of the band theory of solids, and how it relates to the electronic, thermal C203.4 and magnetic properties of materials. To give student broad introductory knowledge of the ceramic, plastics, composites and other C203.5 materials and how the materials properties ultimately affect engineering design in their respective disciplines, and how such properties lead to limitations. Industrial Psychology(NHU-301): C205 Year of Study: C205.1 Understand the Nature and Scope of Industrial Psychology and determine the scope for development of industrial growth with various tools. C205.2 Identify the role of Motivation and Job satisfaction, stress management. Organizational culture, Leadership & group dynamics C205.3 To determine the work environment for efficient work and provide adequate facilities to achieve organisational objectives. An understanding of the need for high ethical standards in the practice of engineering, C205.4 including the responsibilities of the engineering profession towards people and the environment.

2 C205.5 Understand the need for personnel assets and provider training & development to achieve organizational goal Thermodynamics (NME-303): C206 Year of Study: C206.1 Students are able to understand basic concepts of thermodynamics, Zeroth law of thermodynamics and their application to solve engineering problems. C206.2 Get knowledge of First and Second law of thermodynamics and will be able to solve different thermal problems. C206.3 Gain knowledge of entropy and availability and apply it to solve various thermal problems. C206.4 Get knowledge of working of basic cycle use in steam power plant. C206.5 Get knowledge of working of Internal combustion engines and use in automobiles. Fluid Mechanics Lab (NCE-351): C208 Year of Study: C208.1 The student should be able to verify the momentum equation using the experimental set-up on impact of jet. C208.2 The student should be able to determine the coefficient of discharge of an orifice of a given shape. C208.3 The student will learn to calibrate a Venturimeter and study the variation of the co-efficient of discharge with the Reynolds number. C208.4 The student will learn to calibrate a bend meter and study the variation of the co-efficient of discharge with the Reynolds number. C208.5 The student will understand and learn variation of friction factor, f for turbulent flow in commercial pipes Material Science & Testing Lab (NME-351): C209 Year of Study: Students will learn necessity to material study and material testing procedures and processes C209.1 for quality identification and the best use of material in the context of materials science & engineering. C209.2 Students will be able to test strength of a given mild steel specimen on universal testing machine with full details of stress -strain diagram. C209.3 Students will be able to test the hardness of different materials on two different hardness test methods on a hardness tester. C209.4 Students will be able to test the impact strength of a material by two different methods on impact testing machine. C209.5 Students will be able to prepare a specimen for microstructure examination and identify the microstructure of the specimen. Thermodynamics Lab (NME-353): C211 Year of Study: C211.1 Students are able to understand basic Boiler mountings and accessories. C211.2 Get knowledge of working of fire tube boilers and their applications. C211.3 Get knowledge of working of water tube boilers and their applications. C211.4 Get knowledge of working of steam engine. C211.5 Get knowledge of working of Internal combustion engines and use in automobiles.

3 General Proficiency (NGP-301): C212 Year of Study: C212.1 To develop communication skills in order to encourage them to participate in extracurricular activities. C212.2 To appreciate the sincerity and regularity of the students. C212.3 To develop the overall personality in terms of human values and confidence. C212.4 To nurture them to face the challenges in the corporate world C212.5 To give them the environment to identify their personal hobbies, so they can sharpen their personality as an individual, if not good in academics. Laser Systems and Applications (NOE043): C213 Year of Study: C213.1 An Introduction to the: evolution of Quantum Mechanics (the basis of Laser action) and failures of Classical Mechanics C213.2 An Introduction to the: Characteristics of Laser Light, Threshold condition, Types of Resonators C213.3 Laser and Laser Systems: Principle of Laser action, Main components of a Laser System, Types of Laser systems, CW and Pulsed, Methods of Mode Locking and Q switching C213.4 Lasers & Laser Systems: Introduction, Construction and Working of Various types of Lasers C213.5 Applications of Laser Systems in: Medicine and Surgery; Optical Communication; Holography; Material Processing, Metrology, LIDAR Electrical Machines & Controls (NEE-409): C214 Year of Study: C214.1 To impart knowledge on Constructional details, principle of operation, Performance, starters and speed control of DC Machines C214.2 To impart knowledge on Constructional details, principle of operation of Transformer and AC Machines C214.3 To understand the fundamental of control system design applications. C214.4 To develop an ability to design classical controllers based on Bode plots and root locus techniques C214.5 To study the concept of time response and frequency response of the system Applied Thermodynamics (NME-401): C215 Year of Study: C215.1 Students are able to understand Thermodynamic relations and mathematical representations. Understand fuels and their combustion properties. C215.2 Get knowledge of steam power plant equipment such as boilers and condensers and their functionality and characteristics. C215.3 Get knowledge of working of steam engines and steam nozzles, their performance in a steam power plant. C215.4 Gain knowledge of various power cycles as applicable in steam power plant. C215.5 Get knowledge of Gas turbine cycles and principle of jet propulsion, various types of jet propulsion systems and their performance. Manufacturing Science & Technology I (NME-402): C216 Year of Study: Be able to understand Importance of manufacturing, its Economic & technological considerations and various Metal Forming Processes like Elastic & plastic deformation, yield C216.1 criteria(mises and Tresca s), Hot working versus cold working, including Analysis of Forging process for load estimation with sliding friction, sticking friction and mixed condition for slab and disc. Be able to learn Analysis of Wire/strip drawing, Tube drawing, Extrusion and its application. C216.2 Student will also learn condition for Rolling force and power in rolling. Rolling mills & rolledsections, Design, lubrication and defects in metal forming processes. C216.3 Be able to learn basics of Sheet Metal working, Presses and their classification, Die & punch

4 C216.4 C216.5 assembly and press work methods and processes. Cutting/Punching mechanism, Blanking vs. Piercing. Compound vs. Progressive die & Analysis of forming process like cup/deep drawing. Be able to learn basics of casting, Basic principle & survey of casting processes, types of patterns and allowances. Types and properties of moulding sand, sand testing. Mould and design considerations, Gating, Riser, Runnes, Core, Cupola furnace, Die Casting, Centrifugal casting and Investment casting. Be able to design various Unconventional Metal forming processes like Unconventional metal forming, explosive forming, electromagnetic, electro-hydraulic forming, Powder Metallurgy, its application. Also student learns Jigs & Fixtures and its applications, Manufacturing of Plastic components, Review of plastics, and its past, present & future uses, Injection moulding and Extrusion of plastic. Industrial Sociology (NHU-402): C217 Year of Study: C217.1 Understand the Nature and Scope of Industrial sociology and with Characteristics of the factory system and Work Environment C217.2 Identify the role of Motivation and Job satisfaction, stress management. Organizational culture, Leadership & group dynamics C217.3 Identify and employ various research designs and their appropriate application to the study of social life, Performance Management, Training & Development An understanding of the need for high ethical standards in the practice of engineering, C217.4 including the responsibilities of the engineering profession towards people and the environment. C217.5 Understand the need for personnel and techniques for training and development for good personnel Measurement and Metrology (NME-403): C218 Year of Study: Students learn and understand the need and development of new concepts with measurement C218.1 and metrology. The students get the knowledge of calibration of the process where metrology is applied to C218.2 measurement equipment and processes to ensure conformity with a known standard of measurement, usually traceable to a national standards board. Students are able to recognize the concepts of errors, uncertainty of individual measurements, C218.3 and attempts to validate each measurement made with a given instrument, and the data obtained from it. Students will have the capability to apply the skills in measuring force, torque, strain, pressure C218.4 and temperature. To understand the principles of metrology and measurements for many parameters and its C218.5 application in manufacturing industries. Electrical Machines & Controls Lab (NEE-459): C220 Year of Study: C220.1 To implement the basic principles of Servo-Motor calibration of DC Machines C220.2 C220.3 To study the effects of Lead, Lag and Lag-Lead series compensator on a second- Order system transient and steady state system response. To understand the performance and characteristics of DC machines and Transformers C220.4 To Perform testing on transformer and to evaluate efficiency and voltage regulation. C220.5 The students are aware of various types of control systems.

5 Manufacturing Technology I Lab (NME-452): C222 Year of Study: Students will learn the necessity to manage manufacturing processes and systems for the best C222.1 use of material and human resources with particular emphasis on quality and product cost, human safety and environmental considerations. Students will learn to design a pattern and to make a pattern as per design, produce a sand C222.2 casting and gravity die casting. C222.3 Students will be able to perform to different sheet metal operations on press machines. C222.4 Students will be able to perform forging operations and injection moulding process to produce a desired product. C222.5 Students will be able to perform sheet bending and pipe bending operations. Measurement and Metrology Lab (NME-453): C223 Year of Study: C223.1 Students learn and understand about measuring equipments used in Industries. C223.2 Students will be able to work in Quality control and quality assurances divisions in industries C223.3 Students learn and understand about use of different gauges used in Industries. C223.4 Students learn to design a sensors and transducers used for stress analysis. C223.5 Students learn to use measuring equipments for the measurement of temperature, Pressure and flow used in industries. General Proficiency (NGP-401): C224 Year of Study: To develop communication skills in order to encourage them to participate in extracurricular C224.1 activities. C224.2 To appreciate the sincerity and regularity of the students. C224.3 To develop the overall personality in terms of human values and confidence. C224.4 To nurture them to face the challenges in the corporate world C224.5 To give them the environment to identify their personal hobbies, so they can sharpen their personality as an individual, if not good in academics. Machine Design-I(EME-501): C301 Year of Study: Students will be able to understand the basics of Machine Design and able to solve static C301.1 load problems using theory of failure. Be able to understand and design components for finite and infinite life of against fluctuating C301.2 load and will develop understanding of the application of riveted joints for permanent fastening and be able to design different riveted joints and boiler joints. Be able to design shaft based on strength and rigidity and be able to design machine C301.3 elements e.g. keys, splines, rigid and flexible coupling. Be able to understand basics of helical spring including their end connections, stresses, and C301.4 deflection and able to design helical springs subjected to static and fatigue loading. Be able to understand basics of power screw including their forms, multiple threads, their C301.5 efficiency and stresses. Be able to apply their power screw design knowledge to design a Screw jack.

6 Dynamics of Machines I(NME-502): C302 Year of Study: Students will be able to know about the mechanisms and machines with their applications in C day by day life. C Students will be able about acceleration analysis and kinematic synthesis of mechanism C C C Students can gain knowledge about cam & follower Students will be able to understand about gear and gear trains which are very important and used mostly. Students will understand the different friction drives Manufacturing Science II (NME-503): C303 Year of Study: Students will be able to enhance their skill and learn the basic science of metal cutting, C303.1 geometry & design of tools, analysis of forces, economics of metal cutting and their socioenvironmental effect. Gives the ability to understand, apply and communicate the engineering principles of various C303.2 machines and processes which help in research or production as well as interdisciplinary field which may fulfill the social, economical and political needs of the society. Provides knowledge to understand and solve application level problems in production and C303.3 research field so that the student could fulfill his professional & social responsibilities and also be able to communicate their knowledge to other one. Gives knowledge of basic and advanced welding technology which they could use to analyze C303.4 and solve engineering or research problem of real world which can affect the society and the environment. Helps to understand the science and system design of the unconventional machining and allied C303.5 processes which can be used in various field of engineering and research to solve the engineering problems and fulfill the responsibly towards society. Heat & Mass Transfer (NME-504): C304 Year of Study: Understand the basic laws of heat transfer and analyze problems involving steady state heat C304.1 conduction in simple geometries. C304.2 Develop solutions for transient heat conduction in simple geometries C304.3 Provides knowledge to evaluate heat transfer coefficients for natural convection, forced convection and over exterior surfaces. C304.4 Calculate radiation heat transfer between black body surfaces and grey body surfaces. C304.5 Analyze heat exchanger performance by using the method of log mean temperature difference, NTU effectiveness. I.C. Engines & Compressors (NME-505): C305 Year of Study: Students learn the basic concepts and elements of I.C.Engine. Gives an awareness of basic C305.1 principles of thermodynamics cycles related to engine and factor affecting. Students learn the basics of combustion process and design evolution of combustion chamber C305.2 of spark ignited engine. Gives the ability to understand mathematical basic with reasoning of fuel supply system and performance perspective of turbo-supercharging systems. Students learn the basics of combustion process and Design evolution of combustion chamber C305.3 of Compression Ignition Engine. Gives the ability to understand basic with reasoning of fuel supply system and emission formation and its control. Be able to describe the cooling and lubrication of an Engine with its effect on engine friction C305.4 & heat generation and also Provides knowledge about alternative fuels, engine performance parameters and testing.

7 C305.5 Helps to understand the classification, functionality and characteristics of Reciprocating and Centrifugal Compressors Engineering Economics (NHU-501): C306 Year of Study: C306.1 The course shows how economic principles can be applied to a company s decision making in terms of economic viability. C306.2 Understand demand analysis, Demand forecasting, Law of production and various elements of cost involve in industry. C306.3 Provide Knowledge about industrial production and economies and diseconomies for production scale C306.4 Understand various price policies, market structure and determine price and output in these markets C306.5 Understand the various types and phases of a business cycle and its impact on economy Machine Design-I Lab (NME-551): C307 Year of Study: Be able to understand the application and design of Cotter Joint. Also, be able to and make C307.1 orthographic drawing of Cotter Joint. C307.2 Be able to design the machine components subjected to combined steady and variable loads. C307.3 Be able to understand the application and design of Knuckle Joint. Also, be able to and make orthographic drawing of Knuckle Joint. C307.4 Be able to design a riveted joint subjected to an eccentric load. C307.5 Be able to understand the application of riveted joints in boilers. Also, be able to design a boiler riveted joint. Seminar (NME-552): C308 Year of Study: Able to identified important concepts from the readings and provided depth in coverage of C308.1 the topic. C308.2 Able to work in a group. C308.3 Developed effective group communication and presentation skills. C308.4 Developed self-management & reflection skills. C308.5 Able to write technical documents and give oral presentation. Heat & Mass Transfer Lab (NME-554): C310 Year of Study: Ability to measure the thermal conductivity of different materials (Bar/ C310.1 Cylinder/Powder/Fluid). C310.2 Ability to measure the quantity of heat transfer between fluids and solid boundaries C310.3 Ability to measure the amount of heat exchanged between fluids flowing within heat exchangers. C310.4 Ability to carry out simple experimental work in radiation heat transfer. C310.5 Ability to carry out simple experimental on heat transfer due to conduction, convection and radiation.

8 General Proficiency (NGP-501): C311 Year of Study: To develop communication skills in order to encourage them to participate in extracurricular C311.1 activities. C311.2 To appreciate the sincerity and regularity of the students. C311.3 To develop the overall personality in terms of human values and confidence. C311.4 To nurture them to face the challenges in the corporate world C311.5 To give them the environment to identify their personal hobbies, so they can sharpen their personality as an individual, if not good in academics. Machine Design-II (NME-602): C312 Year of Study: Be able to understand basics of spur gears and helical gears. Students will also develop C312.1 understanding to learn force analysis and design procedures including beam strength and wear strength for both spur gears and helical gears. Be able to learn terminology, force analysis, beam strength and wear strength of bevel gears C312.2 and worm gears. Be able to learn basics of sliding contact bearings with their different types of lubrication and C312.3 will be able to select bearing from manufacturer catalogues as per the requirements. Students will also be able to design thrust bearing with pivot and collar configuration. Be able to learn basics of rolling contact bearing including their types, selection and life. C312.4 Students will be able to select bearing subjected to dynamic equivalent load for roller contact bearing under constant and variable loading along with varying reliability. Be able to design various IC Engine parts e.g. cylinder and cylinder head, piston and its parts C312.5 like piston ring and gudgeon pin, connecting rod and crankshaft. Dynamics of Machines (NME-603): C313 Year of Study: Students will be able to know about the static force analysis of mechanisms and minimizing C energy fluctuation by using flywheel C C C Students will be able to know the basic of gyroscope and vibration Students will understand the unbalanced force in rotating/reciprocating parts and its effect and remedies Students can improve their knowledge about the different types of governor C Students will be able to understand about brake and dynamometer Refrigeration & Air-Conditioning (NME-604): C314Year of Study: C314.1 Students learn the basic concepts and elements of Refrigeration and Air conditioning with thermodynamic approach. C314.2 Gives the ability to understand vapour compression refrigeration cycle using thermodynamic principles specification C314.3 Provides knowledge of absorption refrigeration, different types of refrigerant with properties. C314.4 Gives an awareness of basic heat load calculation. C314.5 Helps to understand the functionality of ducts, design of ducts and different pshychrometric processes in air-conditioning.

9 Mechatronics (NME-014): C315 Year of Study: Students will be able to enhance their skill and learn the basic elements of mechatronics and its application in design, modeling, research and other engineering fields which could help to C315.1 make them a good professional and understand their responsibility toward their team & the society. Gives the ability to understand, apply and communicate the engineering principles of various C315.2 electronics & computing elements and use them as modern engineering tools in engineering and research field on global level. Students will be able to do system modeling, analysis & design the motion control devices C315.3 used in different machines which helps to fulfill the need of society in socio-economic level and also able to identify & solve the engineering problem. Gives knowledge of basic and advanced types of sensors and transducers which they could C315.4 use to analyze and solve contemporary issues of engineering or research problem within realistic constraints which can lead for the better society. Helps to understand the science and engineering of mechatronics which can be used in C315.5 various field of engineering and research to fulfill the responsibility towards society, face the global challenges and make them inclined towards the modern technology. Fluid Machinery (NME 021): C316 Year of Study: Students learn the basic concepts of momentum equation and its application. Student will be C316.1 able to understand theoretical aspects of the construction, functionality, performance characteristics and control of impulse turbine. Student will be able to understand theoretical aspects of the construction, functionality, C316.2 performance characteristics and control of reaction turbines. Also generate understanding of cavitation and selection of turbine. Student will be able to understand theoretical aspects of the classification, construction, C316.3 functionality and performance characteristics of Centrifugal pump. Also generate understanding of cavitation and selection of turbine. Student will be able to understand theoretical aspects of the classification, construction, C316.4 functionality and performance characteristics of Reciprocating pump and different hydraulic water lifting macines By FMC, students should be able to have basic knowledge of work, power, efficiency of energetic systems, select and evaluate performances of hydro turbines and Pumps. Student will C316.5 be able to investigate theoretical aspects of the design, the installation and the operation of hydraulic machines. Industrial Management (NHU-601): C317 Year of Study: C317.1 Provide knowledge about the fundamental tools and Techniques in Industrial Engineering. C317.2 Helps to improve inter related work activities and production management in an industry C317.3 Gives awareness about product development and design. C317.4 Helps to manage the job floor of an industry or a research organization efficiently and effectively by the optimized utilization of the resources for the maximum output. C317.5 Understand the product quality, its techniques and overall quality management. Fluid Machinery Lab (NME-651): C318 Year of Study: C318.1 The student will be able to verify momentum equation through impact of jet experiment. C318.2 The student will be able to conduct turbine experiment on Francis Turbine. He should also be able to draw graph between discharge/efficiency, speed/brake power etc.

10 C318.3 The student will learn to do experiment on Centrifugal Pump and find out discharge, brake horse power (BHP), efficiency, specific speed of pump etc. He will also learn to draw different characteristics graph. C318.4 The student will learn about different parts and mechanism of hydraulic brake. C318.5 The student will perform turbine experiment on Pelton wheel and learn the trend by plotting graph between discharge/efficiency, speed/brake power etc. Machine Design-II Lab (NME-652): C319 Year of Study: C319.1 Be able to understand the basics of C programming by writing a program in C/C++ to convert degree Celsius into degree Fahrenheit. C319.2 Be able to understand the basics of C programming by writing a program in C/C++ to find out greatest of three given numbers. C319.3 Be able to write a program in C/C++ to design a Spur Gear. C319.4 Be able to write a program in C/C++ to design a Helical Gear. C319.5 Be able to write a program in C/C++ to design a Worm Gear. Theory of Machines Lab (NME-653): C320 Year of Study: C Student will understand simple linkage models/mechanisms C C C C Student will understand inversions of four bar linkage Student will understand inversions of single slider crank mechanisms Student will understand principle of governors Student will understand principle of gyroscope Refrigeration & Air Conditioning Lab (NME-654): C321 Year of Study: C321.1 Imparts the basic concepts of Refrigeration and Air conditioning in students C321.2 Ability to design refrigeration or air-conditioning equipment that meets the required specification C321.3 Helps to solves simple problems related to heat load calculation. C321.4 Gives an awareness of basic principles and thermodynamics of refrigeration. C321.5 Helps to understand various components of different refrigerators. General Proficiency (NGP-601): C322 Year of Study: C322.1 To develop communication skills in order to encourage them to participate in extracurricular activities. C322.2 To appreciate the sincerity and regularity of the students. C322.3 C322.4 To develop the overall personality in terms of human values and confidence. To nurture them to face the challenges in the corporate world

11 C322.5 To give them the environment to identify their personal hobbies, so they can sharpen their personality as an individual, if not good in academics. Entrepreneurship Development (EOE-071): C401 Year of Study: To Provide knowledge about the importance of entrepreneur and role of small scale industry C401.1 with recent Govt policy toward SSIs. C401.2 To provide project related knowledge its identification, assessment and financial viability. C406.3 C401.4 C401.5 To give knowledge about preparation of balance sheet and marketing,quality, sales of product and maintain good industrial relation in organization To understand the financial functions,to raise funds for project from different sources, risk analysis and cash flow and profit planning of project. To provide knowledge about laws concerning entrepreneur such as partnership, sales and income tax and workmen compensation and role of agencies to assist in small scale industry. Computer Aided Manufacturing (EME-031): C402 Year of Study: C402.1 Students will be able to know about the difference between conventional and NC/CNC Machines and their structures for high speed machining C402.2 Students will learn to do actual CNC programming for drilling, milling and turning operations and will learn basic coded which they may face in the industry C402.3 Students will learn the differences between various types and levels of automation C402.4 C402.5 Students learn the concepts of Flexible Manufacturing Systems and their applications through concepts such as Group Technology and Process Flow Analysis Students are given an introduction into Robotics and its use material handling and production systems Total Quality Management (EME-041): C403 Year of Study: Students be able to understand quality, quality control, concept change, TQM Modern C403.1 concept, procurement procedure, Quality in sales and services, Guarantee, analysis of claims, evaluation of supplies, Capacity verification. C403.2 Have an in-depth understanding about quality cost, quality economy& will be able to design and fit organization structure for different types of products and company. C403.3 Students will learn about various control charts and will have in depth knowledge about R chart and C chart with their practical applications. C403.4 Students learn about the concept zero defect, reliability, MTTF, MTBF and control charts for attributes (P chart) with their applications. C403.5 Students learn the concept about ISO: 9000 series, Taguchi method and JIT method. Computer Aided Design (EME-701): C404 Year of Study: C404.1 Students will be able to know about the CAD/CAM environment and devices used in CAD. C404.2 Students will be able understand graphic function and manipulate coordinate systems, views, and transformations. C404.3 Students will learn about curve representations and determine their differential properties C404.4 C404.5 Students learn the concepts of surface representations, fundamentals of solid modelling and related commands. Students learn the concepts of different numerical methods and perform basic finite element analysis.

12 Automobile Engineering (EME-702): C405 Year of Study: Students will be able to enhance their skill and learn the constructional, working principle of C405.1 various types of manual transmission of an automobile and Design principles of automotive components to utilize in developing newer production methods. Gives the ability to understand, apply and communicate the working of transmission system of an automobile along with the concepts of Front Axle and steering so as to help in research C405.2 and interdisciplinary field which may fulfill the social, economical and political needs of the society. Gives the knowledge of Braking, Chasis and suspension system of an Automobile which C405.3 they can use to solve engineering or research problem of real world which can bring the change in production methods and society, environment. The student will have knowledge about electrical components and fuel supply system used in C405.4 a vehicle which can help in improvisation and developing newer technologies that can help in developing a better world. Helps to understand the Science behind the Air conditioning, maintenance of an automobile C405.5 along with the awareness of pollution which can be used in field of engineering and research to solve the engineering problems and fulfill the responsibly towards society. CAD/CAM LAB (EME-751): C406 Year of Study: C406.1 Students learn and understand the need of CAD/CAM Environments. C406.2 Students learn and understand the concept of 2D/3D geometric modelling, analysis etc by help of CAD packages. C406.3 Students learn about concepts of C and C programming in design. C406.4 Students learn CAM and overview of CNC programming C406.5 Students learn manual part programming and robotics I.C.Engine & Automobile Lab (EME-752): C407 Year of Study: C407.1 Students were able to understand the working of major components of an automobile. C407.2 Students were able to understand working of transmission, suspension, steering and braking systems. C407.3 Students were able to perform the Morse test on Engine Test Rig. C407.4 Students were able to understand the maintenance procedures for automobiles C407.5 Students were able to understand the working of Ignition system, Fuel Supply System of S.I. Engines and C.I. Engines. Project (EME-753): C408 Year of Study: Student should be able to manage project as a member of team to use the technique, skill and C408.1 modern engineering tools. C408.2 Students should be able to create solutions to authentic (real world and ill-defined) problems. C408.3 Students will be able to collect and disseminate information related to selected project. C408.4 C408.5 Students should be able to design a system, component or process to meet desired need within realistic constraints. Students should be able to develop an action plan to improve presentation skills and have the confidence to make more of an impact on their audience.

13 Industrial Training I & II& Viva- Voce(EME-754): C409 Year of Study: The Industrial interaction is to help students gain first hand information regarding functioning of the Industry Which presents the students with opportunities to plan, organize C409.1 and engage in active learning experiences both inside and outside the classroom. C409.2 It helps to bridge the gap between classroom and the real field world. C409.3 C409.4 C409.5 Students are benefited to learn about real life examples of business and engineering management Industrial interaction makes students understand the subject to its core and its deeper practical experiences in real field situation. Interaction to manufacturing firms is useful for students. To understand the nuances and realities of the shop floor, which in itself is a rare exposure. By visiting the shop floor they get to understand the risky conditions in which workers work, the people management challenges involved in managing workers apart from getting hands-on technical knowledge. General Proficiency (NGP-701): C410 Year of Study: To develop communication skills in order to encourage them to participate in extracurricular C410.1 activities. C410.2 To appreciate the sincerity and regularity of the students. C410.3 To develop the overall personality in terms of human values and confidence. C410.4 To nurture them to face the challenges in the corporate world C410.5 To give them the environment to identify their personal hobbies, so they can sharpen their personality as an individual, if not good in academics. Non-Conventional Energy Resources (EOE-081): C411 Year of Study: Be able to understand the principle of working the components of different non-conventional C411.1 sources of energy and their utilization. To provide the most cost effectiveness of various energy sources and options for meeting the C411.2 requirements for social development with due environmental considerations and solar energy related issues. Generate electricity through renewable resources like geothermal, magneto hydro dynamics C411.3 and applications of fuel cells. Students learn the concepts of Import and adoptable technology and machinery in the areas C411.4 of Non-conventional energy sources and ensures post installation services like wind energy concentrators, rotors and Thermionic and thermoelectric conversion. Students are given an introduction about the bio gas energy generation and OTEC power C411.5 plant, tidal energy and wave energy. Operations Research (EME-051): C412 Year of Study: Be able to understand definition, scope, objectives, phases, models and limitations of C412.1 operation research C412.2 Be able to understand different application areas of operations research C412.3 Be able to succeed in stating whether a problem can be solved using operations research C412.4 Be able to solve the problems related to transportation problem, assignment model, sequencing model, dynamic programming, game theory, queuing theory and inventory models C412.5 Be able to understand project management.

14 Non-Destructive Testing (EME-062): C413 Year of Study: Students will able to understand different types of non-destructive testing methods and be C413.1 able to differentiate between destructive & non-destructive testing methods. They will learn about visual inspection method and chalk whitening method C413.2 Have an in-depth understanding of Die penetration method and magnetic particle testing method. Also they will learn about Leak testing. C413.3 Students will learn X-ray radiographic method and gamma ray radiographic method. C413.4 Students learn the concept about Piezoelectricity, CRO techniques & Ultrasonic testing method with their application in castings, forgings etc. C413.5 Students learn the in-depth about Eddy current inspection method, also be able to understand its application, limitations, advantages etc. Power Plant Engineering (EME-801): C414 Year of Study: Students will be able to learn the basics of power and Energy, define terms and factors associated with power plant economics, Calculate present worth depreciation and cost of different types of power plants, and Estimate the cost of producing power per kw which will C414.1 help to make them a good professional and understand their responsibility toward the society. The students will learn the operating procedure of a thermal power plant and also the details C414.2 of different machineries used in such power plants so that they will be able to plan for a thermal power plant using modern engineering tools on global level. Students will be able to know the basic working principles of gas turbine and diesel engine power plants, Define the performance characteristics and components of such power plants, C414.3 Classify different types of coupled vapor cycles and list the advantages of combined cycle power plant so as to fulfill the need of society in socio-economic level. Gives Knowledge of the various types of non-conventional power plant, hydroelectric Power plant, and Nuclear power plant along with the principal components of these Plants which C414.4 they could use to analyze and solve engineering or research problem which can lead for the better society. Gives the ability to understand, apply and communicate the engineering principles of C414.5 electrical and instrumentation system used in power plants along with the awareness of pollution from such plants to be used by them in modern engineering tools on global level Project (EME-851): C415 Year of Study: Student should be able to manage project as a member of team to use the technique, skill and C415.1 modern engineering tools. C415.2 Students should be able to create solutions to authentic (real world and ill-defined) problems. C415.3 Students will be able to collect and disseminate information related to selected project. C415.4 C415.5 C415.6 Students should be able to design a system, component or process to meet desired need within realistic constraints. Students should be able to develop an action plan to improve presentation skills and have the confidence to make more of an impact on their audience. Students should be able to develop skill to execute the action plan with in discussed time period General Proficiency (NGP-801): C416 Year of Study: To develop communication skills in order to encourage them to participate in extracurricular C416.1 activities. C416.2 To appreciate the sincerity and regularity of the students. C416.3 To develop the overall personality in terms of human values and confidence.

15 C416.4 To nurture them to face the challenges in the corporate world C416.5 To give them the environment to identify their personal hobbies, so they can sharpen their personality as an individual, if not good in academics.