Hilti X-CR Nail Product Information 2 6 X-CR Nails DX 460 Tool DX 36 Tool Technical data 7-11 Government Letters 12 16 Country of Origin 17 Job Reference 18 21 Make your submission simple! To download the most updated submission folders and technical manuals, visit http://www.hilti.com.hk/download Recycling one ton of paper saves 17 trees and 7000 gallons of water. Please consider your environmental responsibility before using the hard copy version! 1 06/2017
Direct Fastening Stainless steel nail X-CR Applications Fastening in outdoor applications, directly or indirectly exposed to the weather Advantages Corrosion-resistant Suitable for universal use Technical data Material Equivalent to A4(316) stainless steel For use with DX 36, DX 351, DX 460 Stainless steel nail X-CR P8 Ordering designation Fastener shank length Fastener shank diameter Sales pack quantity Item number X-CR 16 P8 16 mm 3.7 mm 100 pc 247356 1) X-CR 21 P8 21 mm 3.7 mm 100 pc 247358 X-CR 24 P8 24 mm 3.7 mm 100 pc 247359 1) X-CR 29 P8 29 mm 3.7 mm 100 pc 247360 1) X-CR 34 P8 34 mm 3.7 mm 100 pc 247361 1) X-CR 39 P8 39 mm 3.7 mm 100 pc 247362 1) X-CR 44 P8 44 mm 3.7 mm 100 pc 247363 1) 1) This is a non-stock item. For detailed lead time information please contact your Hilti representative. Please visit Hilti website for the latest item numbers and related products 7 Stainless steel nail with washer X-CR P8 S Ordering designation Fastener shank length Fastener shank diameter Washer diameter Sales pack Item number quantity X-CR 21 P8 S23 21 mm 3.7 mm 23 mm 500 pc 3457801 Please visit Hilti website for the latest item numbers and related products 2 06/2017 Customer Hotline: Hong Kong 8228 8118, Macau 00800 8228 8118 Email: hksales@hilti.com 215
Direct Fastening Powder-actuated tool DX 460 Applications Fastening wood to concrete, sand-lime block or steel Fastening sheet metal to concrete, sand-lime block or steel Advantages Excellent power-to-weight ratio for fastening a wide variety of materials to concrete and steel Outstanding ergonomic design and reduced recoil Fully automatic Low noise level Technical data Power (max.) Weight Base materials Automatic piston return Noise (pressure) level at work station: LpA, 1s 1) Dimensions (LxWxH) Max. fastener driving rate Cartridge type Fastener intake Fastener length range 325 J 3.2 kg Concrete, Steel Yes 95 db (A) 463 x 72 x 180 mm 700 / h 6.8/11 M10 Single 12-72 mm 1) Declared measured values of noise characteristics according to 2006/42/EC Machinery Directive in conjunction with E DIN EN 15895 7 Info Shop Ordering designation Package contents Sales pack Item number quantity DX 460 F8 1x DX460-F8, 1x Piston X460P8, 1x Fastener guide X-460-F8 assy, 1x Cleaning kit DX 460, 1x Case, 1x Protective cap X-SGF 1 pc 3485775 Please visit Hilti website for the latest item numbers and related products DX cartridge 6.8/11 M10 Applications For use with DX 460, DX 462, DX 351, DX 450, DX 36, DX A40, DX A41 Info Shop Ordering designation Cartridge type Cartridge power level Sales pack quantity 6.8/11 M10 red 6.8/11 M BULK red 6.8/11 M10 yellow Item number.27 calibre short Heavy 200 pc 2126838.27 calibre short Heavy 1000 pc 50373.27 calibre short Medium-light 200 pc 2126837 6.8/11 M green.27 calibre short Light 100 pc 50351 Please visit Hilti website for the latest item numbers and related products 3 06/2017 Customer Hotline: Hong Kong 8228 8118, Macau 00800 8228 8118 Email: hksales@hilti.com 207
Direct Fastening Accessories for DX 460 Ordering designation Sales pack Item number quantity Buffer X-460-B 1 pc 373330 1) Fastener guide X-460-F10 1 pc 373319 1) Fastener guide X-460-F8 1 pc 304529 1) Fastener guide X-460 F8GR 1 pc 386012 1) Fastener guide X-460-F8GR 1 pc 376216 1) Fastener guide X-460-F8S12 1 pc 373317 1) Fastener guide X-460-F8SS 1 pc 373318 1) Fastener guide X-460-FIE 1 pc 373321 1) Piston X-460-P10 1 pc 373300 1) Piston X-460-P8 1 pc 373297 Piston X-460-P8AL 1 pc 373299 1) Piston X-460-P8W 1 pc 373298 1) Piston X-460-PGR 1 pc 305448 1) Piston X-460-PIE 1 pc 373301 1) Pole tool X-PT 460 7FT assy 1 pc 371661 1) Protective cap X-SGF 1 pc 304416 1) Spray 66 ML Cleaning spray 1 pc 308976 Washer holder X-460-WH23/36 packed 1 pc 373331 1) 1) This is a non-stock item. For detailed lead time information please contact your Hilti representative. Please visit Hilti website for the latest item numbers and related products 208 4 06/2017 Hilti online: www.hilti.com.hk
Direct Fastening Powder-actuated fastening tool DX 36 Applications Fastenings on steel, concrete and masonry Attaching drainage foils and membranes to concrete or concrete block Fastening wood to steel or concrete Advantages Drives nails up to 72 mm in length Slim design for good access in tight spaces Automatic cartridge transport Easy to operate Technical data Power (max.) Weight Base materials Automatic piston return Noise (pressure) level at work station: LpA, 1s 1) Dimensions (LxWxH) Max. fastener driving rate Cartridge type Fastener intake Fastener length range 299 J 2.44 kg Concrete, Steel No 100 db (A) 370 x 47 x 152 mm 600 / h 6.8/11 M10 Single 12-72 mm 1) Declared measured values of noise characteristics according to 2006/42/EC Machinery Directive in conjunction with E DIN EN 15895 7 Info Shop Ordering designation Package contents Sales pack Item number quantity DX 36 1x Powder-actuated tool DX 36, 1x Cleaning kit DX 36, 1x Case 1 pc 384032 Please visit Hilti website for the latest item numbers and related products DX cartridge 6.8/11 M10 Applications For use with DX 460, DX 462, DX 351, DX 450, DX 36, DX A40, DX A41 Info Shop Ordering designation Cartridge type Cartridge power level Sales pack quantity 6.8/11 M10 red 6.8/11 M BULK red 6.8/11 M10 yellow Item number.27 calibre short Heavy 200 pc 2126838.27 calibre short Heavy 1000 pc 50373.27 calibre short Medium-light 200 pc 2126837 6.8/11 M green.27 calibre short Light 100 pc 50351 Please visit Hilti website for the latest item numbers and related products 5 06/2017 Customer Hotline: Hong Kong 8228 8118, Macau 00800 8228 8118 Email: hksales@hilti.com 209
Direct Fastening Accessories for DX 36 Ordering designation Sales pack quantity Item number Baseplate 36/S13 1 pc 3738 1) Fastener guide 36/F3 1 pc 3737 1) Piston 36/DNI packed 1 pc 409313 Spray 66 ML Cleaning spray 1 pc 308976 1) This is a non-stock item. For detailed lead time information please contact your Hilti representative. Please visit Hilti website for the latest item numbers and related products 210 6 06/2017 Hilti online: www.hilti.com.hk
X-CR X-CR Stainless Steel Nails for Concrete, Sand lime Masonry and Steel Product data Dimensions X-CR P8 o3.7 2.4 Ls L X-CR P8 o4 2.4 Ls L o8 o4 2.4 Ls L X-CR P8 S12 X-CR 48 P8 S15 o4 o15 o12 o8 General information Material specifications Nail shank: CrNiMo Alloy f u 1850 N/mm 2 (49 HRC) Zinc coating: X-CR 48 P8S15 has 5 13 µm Zinc coating to improve anchorage in concrete Fastening tools DX 460, DX 36, DX-E72 See fastener selection for more details. Approvals DIBt (Germany): ICC (USA): ABS, LR: X-CR 48 P8 S15 X-CR with d nom = 3.7 mm all types 2.4 Ls L Applications Examples Treated lumber HD234 112 6E Stainless steel Al Exposure to weather or otherwise corrosive conditions Noble or corrosive fastened material 11 / 2009 2.89 7 06/2017
X-CR Load data Design data DX Standard: Recommended loads Fastening wood to concrete, sandlime masonry or steel Fastening wood to concrete, sandlime masonry: N rec = V rec = 0.4 kn Nrec Vrec Fastening wood to steel: N rec = V rec = 0.6 kn Design conditions: For safety relevant fastenings sufficient redundancy of the entire system is required: minimum 5 fastenings per fastened unit with normal weight concrete base material. All visible failures must be replaced. Valid for concrete and sandlime masonry with strength of f cc < 40 N/mm 2. Valid for predominantly static loading. Soft material: Working loads depend on strength and thickness of material fastened. Do not use working loads in excess of those for wood. Depth penetration and other conditions same as for fastening wood Use R23 or R36 ( 4.5 mm hole) washer to control penetration and to increase pull-over strength. Separately available from Hilti. DX-Kwik (with pre-drilling): Recommended loads N rec,1 [kn] N rec,2 [kn] V rec [kn] M rec [Nm] X-CR 39/44 2.0 0.6 2.0 5.5 X-CR 48 3.0 0.9 3.0 5.5 Conditions: N rec,1 : concrete in compressive zone. N rec,2 : concrete in tension zone. Static or cyclic (5000 load applications) loading. f cc 25 N/mm 2. For higher concrete strengths, higher loadings may be possible if supported by testing. Recommended loads are based on failure of the fastener anchorage in the concrete. Thickness and quality of the fastened material may lower the loadings. Observance of all pre-drilling requirements, fastened thickness limits, and recommended details. 2.90 11 / 2009 8 06/2017
X-CR Test data Important note: test data are for information only and cannot be used for design. These data are examples and do not represent the whole range of applications and load cases. Design data for Hilti DX-standard nails in concrete are based on a specific statistical evaluation method taking into consideration high variation coefficients. The evaluation procedure is described in the Direct Fastening Principles and Technique section of this manual. For more detailed information please contact Hilti. DX Standard: Pull-out loads in uncracked concrete Mean ultimate Variation Embedment Concrete pull-out loads coefficient depth strength Nails N u,m [kn] [%] h ET [mm] f cc [N/mm 2 ] X-CR 4.16 ~45 30 47.1 Pull-over loads (Characteristic values: 5% fractile value) Softwood Hardwood 1.0 mm 0,75 mm (spruce) (beech, Aluminium Steel pre-drilled) sheeting sheeting Nail N test,k [kn] N test,k [kn] N test,k [kn] N test,k [kn] X-CR 3.2 5.2 1.4 3.0 Application requirements Thickness of base material hmin d nom Concrete h min = 80 mm (d nom = 3.7 mm) h min = 90 mm (d nom 4.0 mm) Steel tii t ll 5 mm for fastening of wood Thickness of fastened material t I 25.0 mm (detailed information see fastener selection) 11 / 2009 2.91 9 06/2017
X-CR Spacing and edge distances (mm) Pairs Row along edge General (e.g. group of fasteners) 200 c c 50 200 50 c c 200 200 200 a c c a reinforced* non-reinforced c 100 150 reinforced* non-reinforced c 80 150 * Minimum 6 mm reinforcing steel continuous along all edges and around all corners. Edge bar must be enclosed by stirrups. reinforced* non-reinforced c 80 150 a 80 100 Corrosion information For fastenings exposed to weather or other corrosive conditions. Not for use in highly corrosive surroundings like swimming pools or highway tunnels. For further detailed information on corrosion see relevant chapter in Direct Fastening Principles and Technique section. Application limits Steel 59 Shank length, LS [mm] 54 49 44 39 34 S 355 S 235 29 5 6 7 8 9 10 11 Steel thickness, t II [mm] 2.92 11 / 2009 10 06/2017
X-CR Fastener selection Fastener selection: DX Standard fastening wood or soft material Required nail shank length Wood: L S = h ET + t l [mm] Soft material: L S = h ET + t l 2.4 h cs [mm] h CS 3 mm if possible 2.4 o3.7 L s L o8 Required depth of penetration h ET Normal weight concrete NWC h ET according to concrete strength f cc f cc [N/mm 2 ] 15 25 35 h ET [mm] 32 27 22 Light weight concrete LWC: h ET = 32 37 mm Sandlime masonry SLM h ET according to concrete strength f cc f cc [N/mm 2 ] 15 25 35 h ET [mm] 32 27 27 Steel h ET 10 mm h cs t I t I ti h ET h ET Normal weight concrete NWC Sandlime masonry SLM Steel 11 / 2009 2.93 11 06/2017
12 06/2017
13 06/2017
14 06/2017
15 06/2017
16 06/2017
Attention: To whom it may concern Date: 6 Jun 2017 Ref: 059/DF/WY/17 Subject: Country of Origin Hilti X-CR nails Dear Sir / Madam, Please find below the information of Hilti X-CR nails Brand Name Model Name Manufacturer Address of Manufacturer Country of Origin Supplier Address of Supplier : Hilti : Hilti X-CR nails : Hilti Corporation : FL-9494, Principality of Liechtenstein : Liechtenstein : Hilti (Hong Kong) Ltd. : 701-704 & 708B, 7/F, Tower A, Manulife Finance Centre, 233 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Should you have further questions, please do not hesitate to contact our Technical Representatives or Customer Service Hotline at 8228-8118. Yours sincerely, Wayne Yu Product Manager Hilti (Hong Kong) Ltd. 701-704 & 708B Tower A Manulife Financial Centre 223 Wai Yip Street Kwun Tong Kowloon Hong Kong P +852-8228 8118 I F +852-2954 1751 www.hilti.com.hk 17 06/2017
Job/Application Reference 09-Nov-10 Ref No Date Project Contractor Consulting Engineer Product Application 12894 05-07 Hong Kong Disneyland LAP KEI LEADER ENG CO. LTD. OAP / Maunsell / Meinhardt Gen'l purpose nail X-CR 16 P8 steel hanger fixing 5893 12-06 Eagle's Nest Tunnel & Associated Works (HY/2003/02) KENTSWAY METAL WORKS Maunsell Hyder JV Gen'l purpose nail X-CR 29 P8 window fixing 7353 06-06 Wo Yi Hop Road Services Appartment PAUL Y. CONSTRUCTION & ENGINEERING Maunsell / Meinhardt S23-1.2 WASHER FOR XCR 21P8 ASSEMBLE chicken mesh fixing 7352 05-06 Wo Yi Hop Road Services Appartment PAUL Y. CONSTRUCTION & ENGINEERING Maunsell / Meinhardt Gen'l purpose nail X-CR 29 P8 chicken mesh fixing 17/F, Tower 6, China Hong Kong City, 33 Canton Road, Tsimshatsui, Kowloon, Hong Kong. 1 Hotline : 8228 8118 Fax : 29541751 18 06/2017
Job/Application Reference 09-Nov-10 Ref No Date Project Contractor Consulting Engineer Product Application 29487 08-08 PTM Projects - Paul Y PAUL Y. GENERAL CONTRACTORS LIMITED Gen'l purpose nail X-CR 44P8 waterproof membrance fastening 22111 01-08 City of Dreams Resort GENYIELD CONSTRUCTION CO LTD Gen'l purpose nail X-CR 29 P8 waterproof membrance fastening 17/F, Tower 6, China Hong Kong City, 33 Canton Road, Tsimshatsui, Kowloon, Hong Kong. 1 Hotline : 8228 8118 Fax : 29541751 19 06/2017
Job/Application Reference 09-Nov-10 Ref No Date Project Contractor Consulting Engineer Product Application 37047 02-09 Four Seasons Hotel, Macau (Parcel 2) ARTSCAPES (FAR EAST) LIMITED Gen'l purpose nail X-CR 29 P8 waterproof membrance fastening 17/F, Tower 6, China Hong Kong City, 33 Canton Road, Tsimshatsui, Kowloon, Hong Kong. 1 Hotline : 8228 8118 Fax : 29541751 20 06/2017
Job/Application Reference 28-Mar-11 Ref No Date Project Contractor Consulting Engineer Product Application 39693 01-10 PTM Projects - Yau Lee YAU LEE CONST CO LTD Universal nail X-CR 24 P8 curtain wall fixing Units 701-704, 7/F, Tower A, Manulife Financial Centre, No 223 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong. 1 Hotline : 8228 8118 Fax : 29541751 21 06/2017