SECTION - 3 EARTHING CLAMPS & FITTINGS 78
EARTHING CONDUCTOR TO FLAT SURFACE TYPE ESS - SINGLE CONDUCTOR TYPE EST - TWIN CONDUCTOR Types ESS (single conductor) and EST (twin conductor) clamps are designed to connect copper earthing conductors to flat plates using the bolt,nut and spring washer supplied. Alternatively they can be used for blind hole mounting such as required when connecting to inserts in power poles. For this variation the suffix NC is added to the Cat.No, which stands for non - captured bolt. Refer to Fig. 1 and Fig. 4 below. The nut is replaced by a disposable neoprene washer and a flat and spring washer is fitted under the head of the bolt. The clamp top is raised to provide free movement of the bolt head. All clamps can be supplied electro tin plated to 75 microns when required.for this variation add T to the Cat.No. For example ESS120 NC-T. Castings are in high copper content alloy. Hardware is stainless steel. Longer bolts can be supplied if required. Fig. 1 Fig. 2 Fig. 3 Fig.4 ESS120 NC-T Shown ( plated) ESS 120 Shown (natural) EST 95 Shown (natural) EST120 NC - T Shown (plated) Cat. No. Fig. No. Conductor Range mm² O.D. mm Length (mm) Width (mm) Bolt Size Wt. EST95 3 25 to 95 6.42 to 12.60 47 32 M10x 50.21 ESS120 2 35 to 120 7.65 to 14.25 53 39 M12x 70.32 EST120 3 35 to 120 7.65 to 14.25 54 38 M12x 70.34 ESS120 NC 1 35 to 120 7.65 to 14.25 54 39 M12x 55.32 EST120 NC 4 35 to 120 7.65 to 14.25 53 38 M12x 55.34 EST150 3 35 to 150 7.65 to 15.75 55 40 M12x 70.45 ESS185 2 35 to 185 7.65 to 17.60 62 48 M12x 80.50 EST185 3 35 to 185 7.65 to 17.60 67 48 M12x 80.57 79
EARTH ROD CLAMPS - TYPES ECA, ECP & ECH. ECA1508 ECA1514 ECA1514C Type ECA earth rod clamps are cast in high copper content alloy and fitted with stainless steel U-bolts, nuts and spring washers. Type ECA clamps accommodate earth rods within the range 13 to 15mm diameter. Smaller conductors from 16 to 35mm² can be accommodated in ECA 1514 and ECA1514C by simply inverting the clamp casting. Cat. No. Rod Dia. Cable Range Wt. kg. ECA1508 13-15 16-50mm² 0.160 ECA1514 13-15 *35 150mm² 0.145 ECA1514C 13-15 *35-150mm² 0.150 Type ECP Cat. No. Rod Dia. Conductor Range Weight ECP1309 12-13 16-50mm² 0.112 ECP1509 14-15 16-50mm² 0.125 ECP1914 17-19 16-120mm² 0.200 Type ECP earth rod clamps consist of a single piece high copper alloy casting contoured to accept a wide range earthing conductors.the earthing conductor is clamped directly to the earth rod. The U-bolt, nuts & spring washers are stainless steel. Cat. No. Rod Dia. Conductor Range Weight ECH1914 15-19 50-120mm2 0.350 Type ECH Type ECH1914 takes two cables at right angles to rod. Castings are in copper alloy. U bolt, nuts and spring washers are stainless steel. 80
EARTH ROD CLAMPS - TYPES ECX, ECF & ECG Type ECX earth rod clamps connect a wide range of earthing conductors either at right angles or parallel to the earth rod. They are cast in high copper alloy and are supplied with stainless steel U- bolts,nuts and spring washers. Type ECX Cat. No. Rod Dia. Conductor Range Weight ECX1909 13-19 16-50mm² 0.300 ECX1514 13-15 35-120mm² 0.300 ECX1914 13-19 35-120mm² 0.320 Cat. No. Rod Dia. Earth Strap Drilling Details Weight (kg) ECF13 13 Two holes 0.226 ECF15 15 12 mm dia. On 30mm 0.225 ECF19 19 centres. 0.224 Type ECF Type ECF clamps are designed to connect an earth rod to a copper earthing strap which is drilled to suit the U-bolt. Casting is high copper content alloy. U-bolt,nuts and spring washers are stainless steel. Cat. No. Conductor Range Dimensions (mm) mm² O.D. mm W B H D (Bolt) ECG42 16-70 5.10-10.70 39 27 37 M10 ECG58 70-135 10.70-15.25 50 37 57 M12 Type ECG Type ECG clamps are used for clamping conductors to flat metal surfaces. The hexagon head stainless steel bolt is captured to allow single spanner tightening. Clamping casting is copper alloy. Standard bolt allows clamp to be connected to a maximum thickness of 12 mm. Cat. No. Rod Dia. Cable Range Weight ECT19 15-19 16-120mm² 0.370 Type ECT earthing clamps take two conductors parallel to the rod. Castings are in high copper content alloy. Hardware is stainless steel. Type ECT 81
EARTHING CONDUCTOR PARALLEL TO PIPE TYPE - ECP Type ECP earthing clamps are designed to connect copper earthing conductors parallel to a galvanised pipe. Clamp castings are high copper content alloy. Hardware is stainless steel. Type ECP (Single conductor) Cat. No. Pipe Size I.D. O.D. Conductor range Weight ECP26 19 (3/4 ) 26 16-120mm² 0.275 ECP34 25 (1 ) 34 16-120mm² 0.300 ECP43 32 (1 1/4 ) 43 16-120mm² 0.375 ECP48 38 (1 1/2 ) 48 16-120mm² 0.450 Cat. No. Pipe Size Conductor Range I.D. O.D. Weight ECP60 51 (2 ) 60 16-120mm² 0.580 ECP 60 Type ECP60 takes one, two or three conductors parallel to the pipe. Single conductor is positioned in the centre groove. Two conductors are positioned in the outer grooves. TWO EARTHING CONDUCTORS TYPE - ECT PARALLEL TO PIPE Cat. No. Pipe Size I.D. O.D. Conductor Range Weight ECT34 25 (1 ) 34 16-120mm² 0.300 ECT43 32( 1 1/4 ) 43 16-120mm² 0.375 ECT48 38 (1 1/2 ) 48 16-120mm² 0.450 Type ECT Type ECT earthing clamps take two conductors parallel to the pipe. Castings are in high copper content alloy.hardware is stainless steel 82
TWO EARTHING CONDUCTORS AT RIGHT ANGLES TO PIPE TYPE - EGT Type EGT earthing clamps provide a convenient means of connecting two copper earthing conductors at right angles to galvanised steel pipe.clamp castings are in high copper alloy. U bolts, nuts and spring washers are stainless steel. Pipe Size Cat. No. EGT3414 I.D O.D Conductor Range Weight 25(1 ) 34 16 120mm² 0.875 43 16-120mm² 0.875 EGT4314 32(1 1/4 ) EARTH BONDING CONNECTION - CAT NO. EBC70 Cat No. EBC 70 bonding connection assembly provides a permanent earthing point for commercial applications. The assembly consists of a circular copper alloy earthing terminal to which is fitted a length of 70sq. mm. copper cable, the end of which is connected to a mild steel preformed rod. Both joints are protected by mastic lined heat-shrink tubing. The copper alloy earthing terminal is drilled on centre and threaded M10 for a depth of 25 mm. Standard cable length is three metres. The threaded section provides a means of positioning the terminal during the formwork stage and later as a permanent earthing point. The preformed rod is welded to the steel reinforcement. Other sizes available upon request. Typical welded joint 83
EARTHING ADAPTOR - CAT. No. A4-1727 Cat. No. A4-1727 earthing adaptor is an all stainless steel fabrication designed for hot stick attachment to EDO s thereby providing an earthing stirrup. An M12 threaded Bayonet Spindle is also available to replace the Ring Spindle as shown. Cat numbers are charted below. A Illustrated is the Bayonet Spindle version attached to the lower hinge assembly of the drop-out fuse. Dim (mm) Cat. No Spindle type A A4-1706 Bayonet 90 A4-1727 Ring 90 A4-1739 Ring 136 A4-1740 Bayonet 136 84
HAND OPERATED CLAMPS, TYPES - LCFB - H Types LCFB-H clamps are fitted with a 12mm stainless steel spindle, to which is moulded a glass filled plastic handle for gloved hand operation. Standard handle length is 120 mm. LCFB1 - H120 Is supplied with a B24 Split Bolt Clamp for tap cable range 5-7.7 mm. LCFB1-H120 LCFB2 - H120 Is supplied with an M10 stud for lug connection of the earthing lead. Weight 0.5kg. Other handle lengths available for Bridging Clamp applications. For these other variants, change catalogue number suffix to length of required handle. For example if a 900mm handle is required the catalogue No. becomes LCFB1 or LCFB2 - H900. LCFB2-H120 HAND OPERATED CLAMP TYPE - SEC 32 Type SEC 32 clamps consist of a tin plated bronze clamp assembly and M12 stainless steel spindle to which is moulded a glass filled plastic handle for gloved hand operation The earthing lead is attached by means of a standard lug via the M10 bolt hole in the clamp body. MAIN CABLE RANGE 9mm - 32mm diameter SEC 32 85
INSULATED STICK OPERATED EARTH CLAMPS TYPES - AEC21 & LCFBI-ES EARTHING CLAMP Cat. No. AEC21-25 & Cat. No. AEC21-32 Designed for earthing aluminium conductors within the range of 7/1.75 to 37/3.00. Clamp sections are aluminium. Surfaces are large and edges rounded to prevent conductor damage. Covered spindle prevents thread damage. Cat.No. AEC 21-25 Ferrule section accepts 25.4mm diameter earth stick. Cat.No. AEC21-32 Ferrule section accepts 32 mm diameter earth stick.. Weights 0.75kg and 0.85kg. EARTHING CLAMP Cat. No. LCFB1-ES Forged brass construction. Clamp section tin plated. Spindle is stainless steel. Main conductor range 7/1.70 19/ 3.75. Tap conductor range 7/1.70-19/1.53. Ferrule section accepts 25.4mm diameter earth stick. Weight 0.5kg 86
EARTHING PARKS, TYPE - EBC Earthing Parks are made by fitting type CBC copper bonding clamps with a copper or stainless steel stirrup of sufficient length and width to accommodate standard earth stick heads. Each clamp section accepts a wide conductor range. Stainless steel nuts, flat and spring washers complete the assembly. Cat. No. Stirrup material Conductor Range O.D. (mm.) Min. Max. EBC-3C Copper 7.65 12.60 EBC-3S Stainless Steel 7.65 12.60 EBC-4C Copper 12.60 15.75 EBC-4S Stainless Steel 12.60 15.75 EARTHING TERMINAL - TYPE ET-1 Used in zone substations for connections of portable earthing devices. Manufactured of solid brass. Turned diameter 22mm. Overall length 80mm; turned length 60mm. Thread M16 X2.0. Thread length 40mm. 87
LINE & EARTHING CLAMPS TYPE LCFB COMMON FEATURES. All LCFB Clamp bodies are electro tinned forged brass. All threaded spindles are stainless steel. The Overhead Conductor Range is 7/1.70-19/3.75 (5mm - 19mm.O.D.) Current Rating : 165 Amps LCFB-1. The Stainless steel threaded Spindle is!0 mm. diameter. The stainless steel cross pin is 3mm. diameter x 35 mm. long. Tap Conductor Range is 7/1.70-19/1.53, by the B24 tinned line clamp supplied. MASS: 0.44kg. LCFB-1 LCFB2 12 is similar to the LCFB-1 above except it has a 12 mm. diameter stainless steel threaded Spindle and 6mm. diameter x 50mm. long stainless steel cross pin. Tap Conductor. In place of the B24 tinned line tap this clamp is supplied with an M10 x 30 mm stud for Lug connection of the tap conductor. MASS: LCFB2-12 0.47kg LCFB1 R is manufactured to the same specification as LCFB-1 above but has a ring cast to the 10 mm Stainless Steel Spindle. Ring is 18.0 mm OD and 32.5 mm ID. MASS: 0.47kg. LCFB1-R LCFB2-R is manufactured to the same specification as the LCFB1-R above except it is supplied with an M10 x 30 mm. stud for lug connection instead of the B24 tinned line tap. Threaded spindle is 10 mm. diameter stainless steel. MASS: 0.48kg. LCFB2-R 88
RING OPERATED EARTHING CLAMPS FOR LARGER CONDUCTORS TYPE SEC 32-R & TYPE EDC-1 Type SEC 32-R clamps consist of a tin plated bronze body and sliding jaw assembly actuated by a one- piece forged stainless steel driving ring. Ring inside diameter 19mm.& outside diameter 33mm,is accommodated by standard operating stick heads. MAIN CONDUCTOR RANGE 10mm. - 32mm.O.D. TAP CONNECTION is by means of a standard lug via the M10 stainless steel bolt and nut WEIGHT 0.65 KG.. Type EDC -1 Duckbill earthing clamp is precision cast in aluminium alloy. Ring spindle is in stainless steel and is accommodated by standard operating stick heads. The moving jaw is spring loaded to provide initial contact pressure.on the conductor during installation. MAIN CONDUCTOR RANGE 5mm - 32mm. O.D. TAP CONNECTION is by means of a standard lug to suit the two M12 stainless steel bolts nuts and flat washers. Bolt centre dimension is 50mm. WEIGHT 0.75 KG. 89
BRIDGING CLAMP TYPE - BEC 635 Plated version shown Type BEC635 bridging clamp is a multi-purpose unit capable of clamping onto earthing rods,fence posts or flat bars etc, for the purpose of grounding earthing sets.the clamp body is made of brass. The threaded spindle and tee bar handle is in stainless steel. Attachment of the earth lead is made via the M10 bolt hole in the clamp web. CLAMPING RANGE 6-35mm. Diameter and flat bar up to 35mm. thick. Typical application EARTH STAKE CLAMP TYPE - ESC 1 Type ESC 1 earth clamps are designed to suit the galvanized star pickets used as earthing stakes. They are made from galvanized SG iron and are fitted with galvanized U-bolt,nuts and stainless steel spring washers. 90
THIS PAGE HAS BEEN LEFT BLANK INTENTIONALLY. 91