Features Regulated Converters Description Highest Power Density In SIP Package 1.6kVDC/1 Minute Isolation Efficiency Up To 88% -4 C To +75 C Operating Temperature Range @ Full Load EN695 And UL/EN62368-1 (pending) CB Report Industry Standard Pinout The series offer very high power density (2.7W/cm³), wide input voltage range and an industrial operating temperature range of -4 C to +75 C without derating. High efficiency, tight regulation, 2kVDC isolation and remote on/off are just some of the characteristics of this advanced SIP8 6W converter which is ideal for high density power supply designs in demanding industrial applications. DC/DC Converter 6 Watt 3 SIP8 Single and Dual Output 3 YEAR w a r r a n t y Selection Guide Part nom. Input Output Output Efficiency max. Capacitive Number Voltage Voltage Current typ. (1) Load (2) [VDC] [VDC] [ma] [%] [µf] -53.3S 5 3.3 13 83 66-55S 5 5 12 86 33-512S 5 12 5 87 16-515S 5 15 4 86 14-55D 5 ±5 ±6 84 ±2-512D 5 ±12 ±25 87 ±9-515D 5 ±15 ±2 86 ±66-123.3S 12 3.3 13 81 66-125S 12 5 12 86 33-1212S 12 12 5 87 16-1215S 12 15 4 87 14-125D 12 ±5 ±6 85 ±2-1212D 12 ±12 ±25 87 ±9-1215D 12 ±15 ±2 87 ±66-243.3S 24 3.3 13 81 66-245S 24 5 12 87 33-2412S 24 12 5 87 16-2415S 24 15 4 87 14-245D 24 ±5 ±6 85 ±2-2412D 24 ±12 ±25 87 ±9-2415D 24 ±15 ±2 87 ±66-483.3S 48 3.3 13 81 66-485S 48 5 12 87 33-4812S 48 12 5 87 16-4815S 48 15 4 88 14-485D 48 ±5 ±6 85 ±2-4812D 48 ±12 ±25 87 ±9-4815D 48 ±15 ±2 88 ±66 EN695-1 (pending) EN62368-1 (pending) UL62368-1 (pending) EN5522 compliant Notes: Note1: Efficiency tested at nominal input and full load at +25 C ambient. Note2: Max Cap Load tested at minimum input and constant resistor load. REV.: 1/216 ECO-1
BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Input Filter Input Voltage Range nom. Vin 5V 48V Input Surge Voltage 1 second max. nom. Vin= Quiescent Current Output Voltage Trimming Start-up time Under Voltage Lockout ON/OFF CTRL nom. Vin see calculation on next page nom. Vin= 5V nom. Vin= nom. Vin= nom. Vin= 48V 5V 2V 48V 5V 48V Trim up Trim down 4.5VDC 9VDC DC 36VDC Internal Operating Frequency -1% load 2kHz Minimum Load % 5VDC DC DC 48VDC 2ms 4.5VDC 2.7VDC 9VDC 7VDC DC 15VDC 36VDC 3VDC Capacitor type 9VDC DC 36VDC 75VDC 15VDC 25VDC 5VDC 1VDC 15mA 55mA 28mA 14mA +1% -8% Open 5V<Vr<1VDC Output Ripple and Noise (3) 2MHz BW 5mVp-p 75mVp-p Efficiency vs. Load 1 Notes: Note3: Measurements are made with a 1.µF MLCC across output (low ESR). -125S 1-245S 8 8 Efficiency [%] 6 4 2 9V 15V Efficiency [%] 6 4 2 3V 36V.2.4.6.8 1. 1.2 Output Load [A].2.4.6.8 1. 1.2 Output Load [%] continued on next page ECO-2 REV.: 1/216
Output Voltage Trimming Trim UP Trim DOWN +Vout Vref R1 R2 R3 Trim -Vout R down Vref R1 R2 R3 Trim R up Vout 3.3V 5V 15V R1 16.74 kω 1 kω 38 kω 5 kω R2 1 kω R3 52.3 kω 39 kω 68 kω 68 kω Vref 1.24 V 2.5 V Trim Calculation R up = q a*r2 Vref r - RI3 = kω a = q r * R1 = kω DVout = Output Voltage Trim R2 - a DVout - Vref R up = trim up resistor R down = trim down resistor b*r1 R down = q r - R3 = kω b = q DVout - Vref r * R2 = kω a = trim up factor R1 - b Vref b = trim down factor Practical Example: Trim Up: Vout = 5V, DVout = 1% (5.5V), Vref= 2.5V 2.5V a = q r * 1kΩ = 8.33kΩ 5.5V - 2.5V R up = q 8.33kΩ * 1kΩ r - 39 = 11.kΩ 1kΩ - 8.33kΩ -xx3.3s Trim up 1 2 3 4 5 6 7 8 9 1 % Vout = 3.33 3.36 3.39 3.43 3.46 3.49 3.53 3.56 3.59 3.63 Volts = 1151.73 36.87 197.7 126.28 86.79 61.6 44.14 31.32 21.15 13.76 KOhms -xx5s Trim up 1 2 3 4 5 6 7 8 9 1 % Vout = 5.5 5.1 5.15 5.2 5.25 5.3 5.35 5.4 5.45 5.5 Volts = 461. 211. 127.67 86. 61. 44.33 32.43 23.5 16.56 11. KOhms -xx12s Trim up 1 2 3 4 5 6 7 8 9 1 % Vout = 12.12 12.24 12.36 12.48 12.6 12.72 12.84 12.96 13.8 13.2 Volts = 723.67 327.83 195.89 129.92 9.33 63.94 45.1 3.96 19.96 11.17 KOhms -xx15s Trim up 1 2 3 4 5 6 7 8 9 1 % Vout = 15.15 15.3 15.45 15.6 15.75 15.9 16.5 16.2 16.35 16.5 Volts = 765.33 348.67 29.78 14.33 98.67 7.89 51.5 36.17 24.59 15.33 KOhms continued on next page REV.: 1/216 ECO-3
Trim down: Vout = 5V, DVout = -8% (4.5V), Vref= 2.5V b = q 4.6V - 2.5V r * 1kΩ = 8.4kΩ 2.5V R down = q 8.4kΩ * 1kΩ r - 39kΩ = 13.5kΩ 1kΩ - 8.4kΩ -xx3.3s Vout = 3.267 3.234 3.21 3.168 3.135 3.12 3.69 3.36 Volts = 643.6 355.96 233.75 166.13 123.19 93.52 71.78 55.17 KOhms -xx5s Vout = 4.95 4.9 4.85 4.8 4.75 4.7 4.65 4.6 Volts = 451. 21. 117.67 76. 51. 34.33 22.43 13.5 KOhms -xx12s Vout = 11.88 11.76 11.64 11.52 11.4 11.28 11.16 11.4 Volts = 292.33 1398.17 896.78 646.8 495.67 395.39 323.76 27.4 KOhms -xx15s Vout = 14.85 14.7 14.55 14.4 14.25 14.1 13.95 13.8 Volts = 448.67 1965.33 127.89 923.67 715.33 576.44 477.24 42.83 KOhms REGULATIONS Parameter Condition Values Output Accuracy ±1% typ. Line Regulation low line to high line ±.2% typ. Load Regulation % to 1% load ±1% typ. Cross Regulation 25% to 1% load ±5% typ. Transient Response 25% load step change 5µs typ. Accuracy vs Load -125S -245S.5.2 Accuracy [ ].45.4.35.3.25.2 9V 15V Accuracy [ ].15.1.5 -.5 -.1 -.15 3V 36V.15 -.2.1.5 1. 1.5 -.25.5 1. 1.5 Output Load [A] Output Load [A] ECO-4 REV.: 1/216
PROTECTIONS Parameter Condition Value Short Circuit Protection (SCP) below 1mW continuous, automatic revovery Over Load Protection (OLP) Isolation Voltage Isolation Capacitance Isolation Resistance Isolation Grade I/P to O/P 15% load, continuous, autmatic recovery 2kVDC / 1 second 1.6kVDC / 1 minute 11pF max. 1GΩ typ. Functional ENVIRONMENTAL Parameter Condition Value Operating Temperature Range (5) without derating (see graph) -4 C to +75 C Maximum Case Temperature Temperature Coefficient +15 C ±.2%/ C Operating Humidity non-condensing 5% - 95% RH max. Vibration MIL-STD-22G MTBF according to MIL-HDBK-217F +25 C 1776 x 1 3 hours Derating Graph (@ Chamber and natural convection) 1 Output Power [%] 8 7 6 4 2 Safe Operating Area -4-2 2 4 6 8 1 75 85 Ambient Temperature [ C] Notes: Note5: Derating Graph is referring to -55S. For more details, please contact our technical support service at TechsupportAT@recom-power.com. 12 SAFETY AND CERTIFICATIONS Certificate Type Report / File Number Standard Information Technology Equipment, General Requirements for Safety (LVD) PENDING EN695-1, 2nd Endition AM2, 213 Audio/video, information and communication technology equipment - Safety requirements (CB Scheme) RoHS 2.1 PENDING EN62368-1, 214 UL62368-1, 2nd Edition, 214 CAN/CSA C22.2 No. 62368-1-14, 214 RoHS-211/65/EU + AM-215/863 EMC Compliance Condition Standard / Criterion Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement continued on next page see filter suggestions EN5522, Class B REV.: 1/216 ECO-5
ESD Electrostatic discharge immunity test ±8kV Air Discharge, ±6kV Contact Discharge EN61-4-2, Criteria A Radiated, radio-frequency, electromagnetic field immunity test 1V/m EN61-4-3, Criteria A Fast Transient and Burst Immunity ±2kV EN61-4-4, Criteria A Surge Immunity ±1kV EN61-4-5, Criteria A Immunity to conducted disturbances, induced by radio-frequency fields 1Vr.m.s EN61-4-6, Criteria A EMC Filtering - Suggestions for EN5522 Class A +Vin -Vin C1 C2 L1 LOAD Model C1 C2 L1-5xx 22µF 1µH -12xx N/A 2.2µH 4.7µF -24xx 6.8µH -48xx 2.2µF 2.2µF 1µH EMC Filtering - Suggestions for EN5522 Class B C7 +Vin C1 C2 C3 C4 C5 L1 L2 C6 LOAD -Vin C8 Model C1 C2 L1 C3 C4 L2 C5 C6 C7 C8-5xx 22µF 1µH N/A 1µF 1µF 47pF 1pF -12xx 1µF N/A 6.8µH N/A 2µH 4.7µF -24xx 4.7µF 1µH 4.7µF 4.7µF 33pF 22pF N/A -48xx 2.2µF 2.2µF 22µH 2.2µF 2.2µF 6µH 1µF 47pF 68pF Surge Protection Circuit according to EN61-4-5, Criteria A +Vin C surge D surge LOAD -Vin Input Voltage Csurge Dsurge max. Surge Voltage 5VDC DC DC 48VDC 1V, 22F E/Cap TVS (P4SMAJ15CA) N/A ±1kVDC ECO-6 REV.: 1/216
DIMENSION and PHYSICAL CHARACTERISTICS Parameter Type Value Material Package Dimension (LxWxH) Case Potting non conductive plastic (UL94V-) Epoxy (UL94V-) 21.8 x 9.2 x 11.1mm Package Weight 4.g Dimension Drawing (mm) embossed logo 21.8 9.2 11.1 Marking 4.1.5.25 2..5 Bottom View 7 x 2.54 = 17.78 3.2 2.54 Recommended Footprint Details 1. Ø +.15/- Top View 2.54 1 2 3 5 6 7 8 Pin Connections Pin # Single Dual 1 -Vin -Vin 2 +Vin +Vin 3 CTRL CTRL 5 Trim NC 6 +Vout +Vout 7 -Vout Com 8 NC -Vout NC= no connection Tolerance: xx.x= ±.5mm xx.xx= ±.25mm Pin dimension: ±.1mm Pin pitch: ±.25mm PACKAGING INFORMATION Packaging Dimension (LxWxH) tube 52. x 18.2 x 11.2mm Packaging Quantity 22pcs Storage Temperature Range -55 C to +125 C Storage Humidity non-condensing 95% RH max. The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM s explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. REV.: 1/216 ECO-7