Installation Instructions Feed Installation for 0.6m(2ft) Spread Spectrum Antennas Bulletin 239851 Revision F Antenna Assembly Sequence P2F/HP2F/PX2F/ HPX2F antenna 1 2 3 1a 1 Apply conductive grease (5) to screw threads and vertex plate spigot of feed assembly (See Warning) Antenna Description This antenna consists of a 0.6 metre (2ft) reflector, radome (if supplied), feed, and offset tower mount. The mount is designed to attach the antenna to a vertical tower pipe of diameter 115 mm (4.5"). The mount also provides adjustment ranges of ±5 elevation and ±5 azimuth. Notice The installation, maintenance, or removal of antenna systems requires qualified, experienced personnel. Andrew installation instructions have been written for such personnel. Antenna systems should be inspected once a year by qualified personnel to verify proper installation, maintenance, and condition of equipment. These antennas should be installed with jumpers from main coaxial feeder cable with appropriate strain relief. Andrew disclaims any liability or responsibility for the results of improper or unsafe installation practices. Fastener Table 1. Fastener Torque Specifications Torque value in N m (lb ft ) for each fastener size Size M4 M5 M6 M8 M10 M12 Stainless 3.25 4.5 7.7 18.7 39.2 65.1 steel 1b 49/52 SERIES P2F-52/ P2F-49 SHOWN Feed mounting hole Apply conductive grease (20) to screw threads and vertex plate spigot of feed assembly (See Warning) 5 4 3 2 Warning: Use protective wear to avoid skin contact with the conductive grease. Keep away from mouth. Wash thoroughly after use with liberal amounts of liquid soap and rinse with water. Do not store open near food or food sources. Contents: oil, clay, and zinc dust. Feed Antenna 57W SERIES P2F-57W SHOWN Feed mounting hole 6 7 5079872 Index
2 Align Polerization Arrow "V" mark on Mounting Ring Align Polerization Arrow with "H" mark on Mounting Ring 3 P2F/HP2F-49/52-DET Antenna Vertical polarization P2F/HP2F-49/52-DET Antenna Horizontal polarization Note orientation of connectors. Vertical polarization connector must always point downward's Note orientation of connectors. Vertical polarization connector must always point downward's HPX2F/PX2F-49/52-DET Antenna Pipe Mount Right HPX2F/PX2F-49/52-DET Antenna Pipe Mount Left
4 Align Polerization Arrow with "H" mark on Mounting Ring Align Polerization Arrow "V" mark on Mounting Ring P2F/HP2F-57W-DET Antenna Horizontal polarization P2F/HP2F-57W-DET Antenna Vertical polarization 5 6 8 12 11 10 Slacken bolts 1/2 turn to adjust azimuth (top & bottom) Rotate to adjust elevation Apply loctite(16) to threads before fitting to antenna 9 When fitting, torque nuts(10) to 22Nm (16.2lb-ft) Slacken bolts 1/2 turn to adjust elevation Rotate to adjust azimuth
7 P2F/PX2F-49/52-N7A Antenna with Feed and Mount Assembled 8 P2F/PX2F-57W-N7A Antenna with Feed and Mount Assembled
9 14 15 10 19 17 18 P2F/PX2F-49/52-NXA Antenna with Feed, Radome HP2F/HPX2F-49/52-NPA Antenna with Feed, Radome
11 14 15 12 P2F/PX2F-57W-NXA Antenna with Feed, Radome 17 18 19 HP2F/HPX2F-57W-NPA Antenna with Feed, Radome
Table 2. Parts List Item Description Part No Qty Contained In 1 Feed Assembly * 1-2 M6 Hex Nut st steel 100526-26 3-3 Lock washer M6 st steel 100522-25 3-4 Washer M6 st steel 100521-25 3-5 Clamp Ring 116375 1-6 Soc Hd Cap Screw M5 st steel 100622-45 4-7 Feed Clip 107445 4-8 Mount 1886 1-9 Scr hex Soc C'sk M10 st steel 204035-25 3 1886 10 Nut hex M10 st steel 100526-37 4 1886 11 Lock washer M10 st steel 100522-37 4 1886 12 Washer Large M10 st steel 100525-31 4 1886 Radome see detail 1-14 Screw Hex Hd M6 st steel 100532-34 6 4252 15 Lock washer M6 st steel 100522-25 6 4252 16 Loctite 108171 1 1886 17 Screw Pan Hd M6 st steel 100511-34 6-18 Lock Washer M6 st steel 100522-25 6-19 Washer M6 st steel 100521-25 6-20 conductive grease 203233 1 1886 * Frequency dependent Hereby ANDREW, a Commscope Company, declares that this antenna is in compliance with the essential requirements of EU Directive 1999/5/EC. A copy of the Declaration of Conformance is available on www.andrew.com Andrew Corporation 10500 West 153rd Street Orland Park, IL U.S. A. 60462 Telephone: 708/349-3300 FAX (U.S.A.): 1-800/349-5444 TELEX: 25-3897 Customer Service, 24 hours: U.S.A. Canada Mexico: 1-800/255-1479 U.K.: 0800 250055 Republic of Ireland: 1 800 535358 Other Europe: +44 592 782 612 Printed in E.C. Feb'03 Copyright 1993 by Andrew Corporation