Hawker hurricane MK.IIa Specification: Length :00 mm(") Wing Span :00 mm(") Wing Area :0. sq. dm.9 sq. ft Wing Loading :.9 g/sq. dm 5.9 oz/sq. ft Flying Weight :.kg(5 lbs) Radio :ch& servos Engine :0 INSTRUCTION MANUAL SAFETY PRECAUTIONS This R/C airplane is not a toy! (The people under years old is forbidden from flying this model) First-time builders should seek advice from people having building experience.if misused or abused,it can cause serious bodily injury and damage to property. Fly only in open areas and preferably at a dedicated R/C flying site. We suggest having a qualified instructor carefully inspect your airplane before its first flight.please carefully read and follow all instructions included with this airplane,your radio control system and any other components purchased separately.
channel radio for aiplane is highly recommended for this model. :0 9 Optional parts: rubber wheel with metal hub, oleo struts and retracts system..7 in Spinner 7 X
Strut Two wheel retract system Make sure to assemble retracts as instructed below. -way pressure inlet -way pressure inlet Strut Rod (x00mm) TP Screw (.xmm) Screw (x5mm) Servo tray(.5x5.5xmm) Wooden Block(0x0xmm) Pin hinge(xmm) Washer(x5mm) Washer(x5mm) Apply instant CA glue to aileron and pin hinge. Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Assemble the aileron to main wing with instant type CA glue. Be careful to ensure the moving parts of the hinges are able to move freely. Install the servo as the illustration below -way pressure inlet Air tank Air inlet Pin hinge(xmm) Quick release connector Quick release connector Pressure reduction inlet Ø.7mm Ø0.mm Switch Make sure hinges are mounted in the same line. Keep some space about mm width between aileron and trailing edge. 5 Install the nylon control horn and connect the linkage. Please insure the sealing of theretract system before flight. Pleas notice the inner diameter of eachside the pressure reduction inlet. Trailing edge Rod (x00mm) Strut ( 90 ) Rod (X00mm) TP Screw(xmm) Switch Air line (000mm) -way pressure inlet Air tank Air inlet Quick release connector Pressure reduction inlet Air valve The status when the gear up Air valve Pull out length of mm to make gear down Aileron Make sure they are in the right position while installing. mm Screw (x0mm)
The position of the control horn in the aileron. Install the servo as the illustration below 7 Adjustment. 77 The centre of the Gravity. Side View RUDDER 0mm mm 0mm 0mm Top view 7 Secure the servo.install the nylon control horn and connect the linkage. 9 Secure the servo with servo tray. 7 The front view and side view when the model install completion. TP Screw (.xmm) Rod (x00mm) TP Screw (.xmm).5mm Screw (x0mm) Washer(x5mm) mm Washer Screw (x5mm) TP Screw (.xmm) TP Screw (.xmm) Rod (x00mm) TP Screw (.xmm) Screw (x5mm) Servo tray(.5x5.5xmm) Wooden Block(0x0xmm) Pin hinge(xmm) Washer(x5mm) Washer(x5mm) Metal wire (.x0mm) Rib template (mm ply) Wood dowel (x0mm) 0 0 According to the rib template drill holes to the wing root and epoxy wood dowel in them. mm Rib template (mm ply) Wood dowel (x0mm) 5
7 Assemble the receiver and the battery to appropriate in the fuselage. 7 Epoxy the landing gear to the wing steadily. According to the rib template drill holes to the relevant position in the mid wing. Connect the flap by a bended metal wire. Metal wire (.x0mm) mm 70º 0mm Rib template (mm ply) 70º Wheel (00mm) Collar (5mm) Wooden Block(xxmm) Landing gear (5mm) TP Screw (x0mm ) Landing gear straps Gear door Wooden Block(5x5xmm) TP Screw (.xmm) Washer (xmm) 7 Adjustment. Side View AILERON FLAP AILERON FLAP 0mm 0mm 0mm Assemble the wings. Drill.mm holes at the place of main wing. Install the wing to the fuselage with x50mm screws as shown in the diagrams below. A B A` B` A=A' B=B' 5 Epoxy the pin hinges to the flaps tightly. Pin hinge(xmm) 0 7 Assemble the wheel and gear door to landing gear. 75 Adjustment. Epoxy the main wing to the mid wing through the main wing joiner and wood dowel. Keep some space about mm width between trailing edge and flap. Collar (5mm) Main wing joiner Trailing edge Collar (5mm) TP Screw (x0mm) Top view TP Screw (.xmm) Washer (xmm) ELEVATOR 0mm Flap Wooden Block 0mm mm Wooden supporter Side View Centre of Gravity. Position for right diagram. Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Make sure they are in the right position while installing.
Epoxy the flaps to the wings as illustration. 7 Epoxy plies inside the fuselage under the cowing and mount the cowing with TP screw as illustration. Install the servo. mm Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Nut (mm) Wheel (00mm) Bushing (Xmm) Wooden Block(5x5xmm) Gear door TP Screw (x0mm) Screw (x50mm) Blind Nut (mm) Wood dowel (x50mm) Washer (xmm) PVC part PVC part TP Screw (.xmm) Ply (5x5xmm).5mm Screw (x0mm) Ball joint Steel wire Washer(x5mm) Lock Nut (mm ) Screw (x0mm) Nut (mm ) Washer(x5mm) Install the nylon control horn and connect the linkage. 0 Mount the gear door and the wheel to the retract. 7 Epoxy the radiator decoration to the appropriate on the mid wing as illustration. 9 Install the servo of swith. Bushing (Xmm) LockNut(mm) Rod (x00mm) 0mm mm Wooden Block Screw (x0mm) Retracts strut Note:rubber wheels oleo struts and retracts are optional. 55mm Add a rubber ring to the clevis for insuring safety 9 Secure the servo.install the nylon control horn and connect the linkage. Cut off the surplus PVC part carefully along the shaded line 70 The servos installation finished sketch map. Rod (x00mm) Screw (x0mm) Washer(x5mm) Washer Screw (x5mm) mm Screw (x0mm) Nut (mm ) Washer(x5mm) Rod (x00mm) Ring Air tank Switch Throttle servo Rudder servo switch servo Elevator servo
Assemble the tail wheel to the tail landing gear. Cut off the surplus shaded portion carefully of the items below. Cut away the shaded portion for assembling the gear house. 5 The sketch maps when the retract up and down. side wing centre wing C C" C = C" Assembly of the stabilizer. Epoxy the muffler to the relevant position on the cowling. Epoxy the gear house to the relevant position. Trim a hole in the appropriate position in the mid wing and drag the servo wires out. Make sure to glue securely. If not properly glued, a failure in flight may occur. Securely glue together.if coming off during flights, you'll lose control of your airplane which leads to accidents! Temporarily fasten down the main wing and check its correct position. 00mm R0 0mm R0 A A' B B' A=A' B=B' 5 Epoxy plies to relevant position inside the fuselage as below for assembling the cowling. Assemble the retracts to the appropriate position in the gear house. 7 Cut the covering off from the shaded portion carefully and glue the PVC part to it. Canopy TP Screw (.xmm) 5 Ply (5x5xmm) 5 TP Screw (x0mm) PVC part TP Screw (.xmm) Ply(5x5xmm).5mm PVC Epoxy plies inside the fuselage under the cowing and mount the cowing with TP screw as illustration. TP Screw (x0mm) 5
Drill holes to appropriate position in the front of mid wing and epoxy wood dowel in them. Assembly of the stabilizer. Epxoy the rudder to the fuselage steadily. 55 5 The sketch map of the linkage for the rudder and the tail wheel. Make sure to glue securely. If not properly glued, a failure in flight may occur. Securely glue together.if coming off during flights, you'll lose control of your airplane which leads to accidents! Temporarily fasten down the main wing and check its correct position. mm A A'.5mm 00mm B B' Wood dowel (x50mm) A=A' B=B' 9 Drill holes to relevant position in the fuselage. 5 Drill a hole to appropriate position in the rudder as illustration. 59 The sketch map of the linkages for the rudder and elevator in the fuselage. mm 00mm TP Screw (.xmm) Pin hinge(xmm) U-style wire (5x5mm) Steel wire (0.5x000mm) Pin hinge(.5xmm) Matal douel (x0mm) Rib template (mm ply) Stab joiner (x0mm) 0mm mm Steel wire (0.5x000mm) 0 Assemble the wings to the fuselage with screw and blind nut as below. Apply instant type CA glue to elevator and pin hinge. The sketch map after the rudder shaft assemble finished. 57 0 Epoxy ply to appropriate position in the fuselage and assemble the tail gear cover with screw. Pin hinge(xmm) Tail wheel TP Screw (.xmm).mm Blind Nut Steel wire Screw(x50mm) Blind Nut (mm) Reinforcement Plate Make sure hinges are mounted in the same line. Aluminum tube Washer(x5mm) Washer(x5mm) Screw (x5mm) Screw (x5mm) Steel wire (0.5x00mm) TP Screw (.xmm) Ply (5x5xmm)
The sketch map when assemble the tail landing 9 5 gear to the wheel steeling mount. Drill a small hole to appropriate possition in the fuselage for installing the plastical tube. Keep some space about mm width between elevator and tailing edge. Drill holes to appropriate position in the stabilizer and epoxy it to the fuselage as below. Tailing edge Tail landing gear Collar Elevator Collar 5mm mm Collar 5mm Plastical tube(x50mm) Make sure they are in the right position while installing. Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! 50 The sketch map of assembling the wheel steeling mount to appropriate position in the fuselage. 5 Drill holes to appropriate position in the rudder and epoxy the ping hinges in them A ccording to thr rib template drill holes to the tail of fuselage as below. 7 connect the fullarm for elevator with steel wire as below. Ply (mm) 0mm Pin hinge(.5xmm) Steel wire (0.5x000mm) U-style wire (mm).mm 0mm mm mm.5mm mm Steel wire (0.5x000mm) Ply (mm) Washer (xmm) TP Screw(x0mm) suggest drilling a hole here for assembling wheel steeling mount Make sure hinges are mounted in the same line. 07mm Rib template (mm ply) 5 The sketch map when tail wheel assemble completion. 5 Keep some space about mm width between the tailing edge and the rudder. 5 Drill two holes at the stabilizer root base on rib template and epexy the wood dowel in them. Glue the elevator to the stabilizer by CA and epoxy. Tailing edge Wood dowel (x0mm) mm Rudder Cut away the rubber tube when the epoxy glue dried. mm mm Make sure they are in the right position while installing. Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! 0 7
Washer(x5mm) Screw (x5mm) Steel wire (0.5x500mm) Aluminum tube(xmm) Plastic tube(x0mm) Nut (mm ) 9 Blind Nut (mm) Screw (x5mm) Screw (x5mm) Washer(xmm) Spring Washer (mm) Install the servo. Set screw (xmm) Engine mount (x05mm) Washer(x5mm) 7 Engine installation finished sketch map. Linkage Stopper Plastic tube (x00mm) Screw (x0mm) Nut (mm) Fuel tank (550cc) Drill holes and set blind nut in appropriate position in the firewall before install the engine. 5.mm Washer (mm) Washer (mm) Linkage Stopper Blind Nut Washer (mm) Nut (mm) Blind Nut (mm) The front view of the engine installation finished. Set screw (xmm) 5 Install the engine carefully. Assembly of the fuel tank. Assemble the throttle servo to appropriate position in the fuselage. Screw (x5mm) Washer (xmm) mm Washer (xmm) Washer (xmm) Spring Washer (mm) Nut (mm) In case of -cycle & -cycle engine. 0 The side sketch map of the engine installation finished. Screw (x5mm) Assemble the accelerateor push rod to the engine. Linkage Stopper Set Screw (xmm) 5 mm Washer (mm) Rod (x00mm) Air pressure line Fuel spray line Washer (xmm) Set Screw (mm) Set Screw (xmm) Fuel supply line Mount the fuel tank to the fuselage. Nose arm(mm) Washer (xmm) TP Screw(x0mm) Tail landing gear(mm) Tail wheel (5mm) Collar (mm) Rod (X57mm) Steel wire (0.5x00mm) Washer(x5mm) Screw (x5mm) Plastical tube(x50mm) Set Screw (mm) Fuel tank (550cc) 9