73 Adjustment. 7 Centre of Gravity. Side View AILERON FLAP 0mm 0mm JU-7D Stuka 30mm Top View AILERON FLAP 35mm 75 The front view when the drop tank and the bombs install completion. Specification: Length :9 mm(.") Wing Span :03 mm(0") Wing Area :0.3 sq. dm.50 sq. ft Wing Loading :0.5 g/sq. dm 3. oz/sq. ft Flying Weight :.5 kg(.3 lbs) Radio :ch& servos Engine :0 -cycle 0 -cycle INSTRUCTION MANUAL SAFETY PRECAUTIONS This R/C airplane is not a toy! (The people under years old is forbidden from flying this model) First-time builders should seek advice from people having building experience.if misused or abused,it can cause serious bodily injury and damage to property. Fly only in open areas and preferably at a dedicated R/C flying site. We suggest having a qualified instructor carefully inspect your airplane before its first flight.please carefully read and follow all instructions included with this airplane,your radio control system and any other components purchased separately.
7 70 Drill holes to appropriate in the bomb. Epoxy the bomb to the bottom wing. 5mm channel radio for aiplane is highly recommended for this model. 0mm 7 Epoxy plastic tube into the holes. Plastic dube (5x30mm) Adjustment. ELEVATOR -cycle.0 Top view 5mm 9 Side View Optional parts: rubber wheel with metal hub. 5mm Position for right diagram..5 in Spinner 5 X7 9 7 Drill holes to relevant pesition in the centet wing. Adjustment. 50mm 90mm 5mm Side View RUDDER 0mm 0mm Top view 3
0 Assemble the cowling. 3 Assemble the stabilizer strut by TP serew. 3 According to the rib template drill holes in one wing and epoxy wood dowel in them. TP Screw (.3xmm) Ply (5x5x) 5 5.5mm Servo tray(.5x5.5xmm) Wood dowel (x30mm) Rib template (mm ply) Epoxy plies inside the fuselage under the cowing and mount the cowing with TP screw as illustration. Ply (5x5x) TP Screw (3x0mm) Copper part Wooden Block(0x0xmm) TP Screw (.3xmm) Main wing joiner Rib template (mm ply) Wood dowel (x30mm) Rib template (mm ply) mm Fix the canopy with self - tapping screws. TP Screw (.3xmm) 0 Ply (5x5x) 0 Trim slots in right position in the bottem wing. mm 79mm mm Fix the aileron servo to the serve tray with epoxy. Fix the flap servo to the servo tray with epoxy. According to the rib template drill holes to another main wing. mm.5mm Rib template (mm ply) Epoxy plies inside the fuselage under the cowing and mount the cowing with TP screw as illustration. Drill holes to the marked position in the fuselage, Drill holes relevant position in the stabilizers. Marked 5 Epoxy the dummy flaps to the wings. Assemble the aileron servo to the wing with screws as below. Assemble the flap servo to the main wing with screws. TP Screw (.3xmm) 5 Epoxy main wings to the centre wing by main wing joiners. A = A" A A".5mm 35mm mm Main wing joiner Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents!
Trim two holes to pull the servo extension lines and fuel tube from the holes. Connect the two flaps with the bended steel wire and keep about mm between the two flap. 55 Instaill the servo in tail of fuselag. Please note the marked point. o 59 Plastic dube (5x30mm) Pvc part Canopy mm TP Screw (.3xmm) Ply (5x5x) 50mm Copper part Steel wire (.x0mm).5mm 50mm TP Screw (.3xmm) Center line 7 Steel wire (.x0mm) 9 The sketch when the wings assemble finished. A Ply (5x5x) According the holes for hinges in the wings make mark in the flaps and aileron(please take step as reference) 5 Dummy flap TP Screw (.3xmm) Bomb TP Screw (3x0mm) The sketch map when the sevos install completion. A` 5 9 5 Trim the cowling for engine and muffler. 59 Epoxy the exhaust to the cowling from inner of the cowing. Throttle servo mm Elevator servo A=A' B=B' aileron Please note the marked point. flap B B` Make sure the hinges can move smoothly. 0 Retainer Rod (x300mm) Screw (3x35mm) Washer(3x5mm) Lock Nut ( ) Washer(3x5mm) Pin hinge Steel wire (.x0mm) Drill holes at the marked position in the flap and aileron 57 Mounting of the receiver and the battery.
50 53 Assemble the rudder servo in the fuselage. Install the servo to the board. Assemble the pin hinge to the wings,the flaps & the ailerons.adjust them to the perfect position. Wheel pants PVC part Wheel (5mm) Collar (mm) Ply (5x5x) TP Screw (3xmm) Landing gear straps Screw (x50mm) Blind Nut (mm) Wood dowel (x50mm) Landing gear Be care the pin hinges should be in line in each plane. Pin hinge 5 5 The sketh amp of the steel wires in the fuselage Install the metal rod control horm and connect the linkage. mm Epoxy the pin hinge steadily in the wings,the flaps and the ailerons. TP Screw (3x0mm) Rod (x300mm) mm Landing gear TP Screw (3x0mm) Make sure the hinges can move smoothly. 5 55 Epoxy two board together and trim a slot to appropriate position in the boards. Drill a hole to appropriate position in the rudder and assemble the metal rod horn to it. 3 Retainer Screw (x0mm) Lock Nut ( ) mm 9mm 5 Rod (x300mm) Rod (x300mm) Landing gear straps Assemble the arms in the flaps and aileron and connect the servo arms to them with rods as below. Lock Nut ( ) Washer(3x5mm) Washer Screw (3x35mm) Washer(3x5mm) Washer Screw (3x35mm) 0 3 Mount landing gear on the underside of wing. Retainer Screw (x0mm) mm Cut off the surplus part of Wheel pants.
9 According to the back steps,epoxy the PVC part to the appropriate place. Cut off the surplus part of pvc parts. 7 Install the engine. Assemble the servos and switch. Set screw (3xmm) Washer (mm) Washer (mm) Linkage Stopper Washer (mm) Nut (mm) Set screw (3xmm) 7 0 Mount wheel pant and tire. Epoxy plastic part underneath the wing. 5 Assembly of the fuel tank. Assemble the servo to fuselage. 9 Install the nylon control ring for switch and connect the linkage. Wheel (5mm) mm Collar (mm) 0mm mm 0mm mm Air pressure line Fuel spray line Wooden Block(5x5x) Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! TP Screw (3xmm) 0mm Attach landing wire to wheel pant steadily. Landing gear straps.5mm Epoxy the dowel on the leading edge of wing. Fuel supply line Mount the fuel tank into the fuselage. Screw (x0mm) Washer(x5mm) Ball joint 75 mm Lock Nut (mm ) Copper joiner Steel wire mm 0mm.5mm mm Copper joiner Screw (x0mm) Wood dowel (x50mm) Fuel tank (550cc) Nut (mm ) Washer(x5mm) 9
Blind Nut (mm) Screw (x35mm) Screw (x5mm) Washer(xmm) Spring Washer (mm) Nut (mm) Linkage Stopper Plastic tube (x500mm) Engine mount (x05mm) Fuel tank (550cc) Plastic tube(3x50mm) 39 Retainer Screw (3x35mm) Washer(3x5mm) Lock Nut ( ) Washer(3x5mm) Copper joiner Screw (x0mm) Nut (mm ) Washer(x5mm) Fiberglass pushrod(3x775mm) Steel wire (0.5x500mm) TP Screw (.3xmm) Ply (5x5x) Drill four holes at the diameters as shown for engine mount. Drill holes in the fuselage to install the main wing. Pin hinge(.5xmm) mm 75 mm Rib template ( ply) Pin hinge(xmm) Steel wire (0.5x3000mm) U-style wire () Tail landing gear 5.mm Tail gear supporter TP Screw ( 3x0mm) Ply (30x0x9mm) Collar () Tail wheel (5mm) Blind Nut Blind Nut (mm) The front view of the engine install completion. There is 5mm left deflection as illustration. 3 Stab joiner (x30mm) Matal douel (x30mm) 3 Assemble the engine. 5 Mount the main wing on the fuselage. Epoxy pin hinges to elevator. Screw (x35mm) Washer (xmm).mm 5mm mm Blind Nut Washer (xmm) Washer (xmm) Spring Washer (mm) Nut (mm) 3 The side view of the engine install completion, There is degree right deflection. Blind Nut (mm) Screw (x5mm) In case of -cycle & -cycle engine. 0 Screw(x50mm) Set Screw (3xmm) o Assemble the throttle linkage. Linkage Stopper Washer (mm) 57 mm Rod (x500mm) Washer (xmm) Set Screw (mm) Set Screw (mm) Blind Nut (mm) Rod (x500mm) Assembly of main wing. Drill.mm holes at the place of main wing. Install the wing to the fuselage with x50mm screws as shown in the diagrams below. A A` Keep some space about mm width between the elevator and horizontal tail edge. Trailing edge A=A' B=B' Set Screw (3xmm) Screw (x5mm) Pin hinge(xmm) Elevator mm B B` Make sure they are in the right position while installing. 5
7 30 Drill two holes at the stabilizer root base on rib template and epexy the metal dowel in them. Epoxy the horizontal tail to fuselage.remove paint at fuselage horizontal mating surfaces before epoxy. Stab joiner (0x30mm) Wood dowel (x30mm) 33 3 Epoxy the fibre glass tubes to appropriate position as below. Drill hols to appropriate position in the vertical tail and epoxy the rudder to the vertical tail steadily. Tailing edge Cut away the rubber tube when the epoxy glue dried. Rudder mm.5mm mm Make sure they are in the right position while installing. According to the rib template drill holes in the stabilizer and fuselage! 3 A ccording to thr rib template drill holes to the tail of fuselage as below. Glue the elevator to the stabilizer by CA and epoxy. 3 37 Assemble the tail wheel as below. Fix the tail gear supporter to fuselage. TP Screw ( 3x0mm) x7mm x7mm Tail landing gear.5mm Collar Collar mm Ply (30x0x9mm) Tail gear supporter TP Screw (3x0mm) Rib template ( ply) 9 Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! 3 Set the U-style wire through the tail of fuselage as below. 35 Epoxy pin hinges to rudder. Ply (30x0x9mm) Note:rudder wheel in optional. 3 Epoxy the tail landing gear to the rudder. 0mm Assemble horizontal tail, vertical tail, tail gear separately. Make sure to glue securely. If not properly glued, a failure in flight may occur. mm 35mm C=C' D=D' C U-style wire () Pin hinge 3 Securely glue together.if coming off during flights, you'll lose control of your airplane which leads to accidents! Temporarily fasten down the main wing and check its correct position..5mm 0mm D Make sure hinges are mounted in the same line. 7 C' D'