signo 721 Compact Preset Counter 1 or 2 presets Prescaler with output for connection of a totalizing counter Large, 5-digit LD display Connection by plug-in screw terminals Variety of programming possibilities Small, compact design in DIN dimensions 48 x 48 mm Keypad can be secured against unauthorized access lectronic value retention, environmentally sound, uses no batteries DISPLAY 5-digit LD display with 7 mm high digits. asy to read, decimal point can be programmed if required. Line 1: Shows the current count in counting operation and entry values in programming mode. Line 2: Shows the operator the individual programming steps during programming. VALU INPUT Values shown in the diagrams can be entered or modified with four large keys on the front of the counter. Counter with one preset P Preset COR Correction Prescaler Counter with two presets P1 Preset 1 P2 Preset 2 COR Correction PSC Prescaler Value input Value input PROGRAMMING Counter with gate and display memory Counter with up/down Table (Page 78) Auto- Key 1 Off see Key 2 Off Key- Lock Input 5kHz Display-Hold Off Inhibit Off pnp-input 9 8 7 6 5 4 3 2 1 Set Off 30Hz npn Table (Page 78) Auto- Key 1 Off see Key 2 Off Key- Lock Input 5kHz pnp-input 9 8 7 6 5 4 3 2 1 Set Off 30Hz npn Out 0,05s 1s bist. Out 0,05s 1s bist. The switch positions illustrated in the diagram program the counter as follows: 9 Set mode (subtracting count) 8 With automatic repeat 7 Presets, correction value and 6 prescaler can be modified if "keylock" input is not actuated 5 Keypad reset activated 4 Max. counting frequency 5 khz 3 Display memory Off without function 2 Gate to appl. input } for u/d switch 1 pnp input logic Pot Signal duration OUT approx. 1 sec. 140 Components 2000 NCODRS COUNTRS CONTROLLRS INDICATORS RLAYS PRINTRS CUTTRS
Technical data signo 721 TCHNICAL DATA Display 5-digit, LD, decimal point with soldering bridge Digit height 7 mm Supply voltage V op : 12 24 VDC 5/+ 10 % or 24 VAC ± 10 % or 100 240 VAC, depending on version Current consumption on 12 24 VDC < 300 ma, on 24 VAC < 255 ma, on 100 240 VAC < 55 ma Sensor supply AC operation 24 VDC + 10 %, DC operation V op - 2 V Value retention approx. 10 years, NV memory Operating temperature 0 + 50 C Storage temperature 20 + 70 C lectrical connection plug-in screw terminals Protection class (IC 144) front IP 54; connections IP 20 Interference immunity MC severity 3 acc. to IC 801 - pt. 2 + pt. 4 Vibrostability 30 m/s 2 (50... 500 Hz) acc. to IC 068-2-6 Shock stability 100 m/s 2 (10 ms) acc. to IC 068-2-27 General design acc. to DIN VD 0411; insulation group C Weight approx. 200 g Approvals CSA: LR 30208-12-13 Inputs Amplitude thresholds Active edge Pulse shape Input resistance Count input Min. pulse length Max. counting frequency Control inputs Pulse shape Application (Appl.) < 2 V and > 8 V; max. + 40 VDC positive, can be switched to negative random (squarewave 1:1 for max. frequency) approx. 22 kω adding programmable, prescaler, adjustable from 0.001...9.999 > 100 µs / > 17 ms (depending on counting frequency) 5 khz / 30 Hz PNP or NPN (able to switch over) with static behaviour - manual via keypad - electric, pulse length > 17 ms - automatic when OUT2 responds (only if programmed accordingly) full keypad or only preset 1 (depending on program), static behaviour, pulse length > 17 ms gate, up/down or display memory, depending on version Signal must be applied 50 µs before count pulse Outputs Signal outputs OUT1 and OUT2, depending on version Signal duration OUT1: starts when P1 is reached and ends when OUT2 responds OUT2: starts when P2 is reached from 0.05 s... bistable (adjustable) Relay Contact type counter with 1 P: changeover; counter with 2 P: make contact Max. switching voltage max. 250 VAC or 30 VDC Switching current max. 1 A, min. 100 ma on 20 V Transistor Switching voltage AC operation 24 VDC,DC operation V op -2 V Switching current 20 ma Prescaler (PSC-OUT) Switching voltage AC operation 24 VDC ± 10 %, DC operation V op -2 V Switching current max. 10 ma Signal duration typ. 90 µs Components 2000 NCODRS COUNTRS CONTROLLRS INDICATORS RLAYS PRINTRS CUTTRS 141
signo 721 Technical data KYLOCK Counter with 1 preset Counter with 2 presets Keyl 1 Keyl 2 P COR PSC Keyl 1 Keyl 2 P1 P2 COR PSC sw. 7 sw. 6 term. 14 sw. 7 sw. 6 term. 14 off off low A A A off off low A A A A off off high A A L off off high L A A L on off low A A on off low A A A on off high L A L on off high L L A L off on low A L off on low A A L off on high A L off on high L A L on on low A L on on low A A L on on high L L on on high L L L A = active, L = locked, = masked DIMNSIONS Clamping frame Plug connector terminal CONNCTION DIAGRAM Dimensions in mm Counter with 1 preset Counter with 2 presets 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 + AC-DC supply voltage 2 + AC-DC supply voltage NC 3 NC NC 4 OUT1 Relay or NC 5 transistor output 6 NC OUT Relay or 7 OUT2 Relay or transistor output 8 transistor output OV Sensor supply voltage + Input Appl. Prescaler-OUT NC * 9 OV Sensor supply voltage 10 + 11 Input 12 13 Appl. 14 15 Prescaler-OUT 16 NC * * NC = not connected ORDR INFORMATION Counter with: Relay output Transistor output Function Supply 1 preset 2 presets 1 preset 2 presets Ord. code Ord. code Ord. code Ord. code Gate/display hold 12 24 VDC 0 721 101 0 721 105 0 721 103 0 721 107 24 VAC 0 721 109 0 721 110 100 240 VAC 0 721 102 0 721 106 0 721 104 0 721 108 Up/down 12 24 VDC 0 721 121 0 721 125 100 240 VAC 0 721 122 0 721 126 Inquire for other versions 142 Components 2000 NCODRS COUNTRS CONTROLLRS INDICATORS RLAYS PRINTRS CUTTRS
Multifunctional Counter - Bi-directional tico 732 007 high-contrast LD or LCD-Display, 6 digits small and compact DIN dimensions 48 x 48 mm easy operation by one key per digit direct access to parameters available with 1 or 2 presets transistor and relay with changeover contact, for each preset with integrated separate totalizer 5 basic functions easily programmable: counter, tachometer, time counter, shift counter and batch counter display range from 99999 to 999999 PROGRAMMING count mode 6 R 4 F1 F2 PSC PRG F1 F2 PSC PRG 1 2 3 5 6 and POWR ON and POWR ON > 5 sec preset 1 preset 2 prescaler function-parameter e.g. Basicfunction* F1 PRG F2 PRG programming mode PSC PRG count mode decimalpoint reset/set-mode signal length pnp/npn-selection reset mode output memory time countertachometer keylock for: manual reset preset 1 or 2 prescaler counter tachometer time counter shift counter batch counter * only for multifunction version The important values, preset 1, preset 2, prescaler and separate totalizer can be directly selected. It is necessary only to press the relevant button and the -button together. To make the operation still more easy, access to those values can be locked separately. All other system parameters like operation and count modes are laid down in a common operation level. These parameters are usually programmed once only during the first initiation. Components 2000 NCODRS COUNTRS CONTROLLRS INDICATORS RLAYS PRINTRS CUTTRS 131
tico 732 Technical data TCHNICAL DATA General Counter Tacho Time-counter DIMNSIONS Display LD or LCD, 6 digits, leading zero suppression, decimal point Digit height LD 7.6 mm; LCD 9 mm Supply voltage 12...24 VDC; 24 VAC; 115 VAC; 230 VAC; 50/60 Hz, depending on version Current consumption 12...24 VDC < 150 ma 100/115/230 VAC < 50 ma; including sensor supply Sensor supply only when AC operated: 12... 30 VDC, max 50 ma Data retention non-volatile memory > 10 years Operating temperature 0... +50 C Storage temperature - 20... + 70 C lectrical connection screw terminals Mounting with clamping frame Protection class (IC 144) front side IP 65, terminals IP 20 Vibrostability 10 m/s 2 (10...150 Hz) according to IC 68-T2-6 Shock stability 100 m/s 2 (18 ms) according to IC 68-T2-27 General design according to VD 0411, DIN 57411, protection class II Approvals UL + CUL 96337 Amplitude thresholds < 2 V and > 8 V, max 40 VDC Active edge programmable; positive with pnp input; negative with npn input Pulse shape any (squarewave 1:1 for max. frequency) Input resistance approx. 5 kohm (static) Counting frequency max. 5 khz (2.5 khz bi-directional) Prescaler programmable from 0.001 to 9.999 (999.999) Count inputs A, B - phase discriminator with single evaluation - differential mode (add/sub) - count direction mode - totalizing mode (add/add) Pulse length min. 17 ms (30 Hz), 100 µs (5 khz) Control input C - manual reset possible - external reset, static or dynamic, programmable, pulse length > 5 ms - automatic reset when main preset has been reached (programmable) Relay changeover contact max. 250 VAC / 30 VDC, min. 5 V AC/DC max. 1 A, min. 10 ma, delay < 5 ms Transistor pnp output 12...24 VDC max 10 ma of DC-supply; 12 30 VDC max. 10 ma of AC-supply Method time interval (1/Tau) Display range 1/min or 1/sec Min input frequency 0.125 Hz = 8 sec Alarms 2 alarms with programmable start-up-suppression Time bases programmable; sec, min., h or hh.mm.ss Resolution programmable 1; 0.1; 0.01; 0.001 Function single pulse measurement (short time meter) or cumulated counting (hour meter) Count mode pulse width or period measurement (start-stop) Dimensions in mm plug terminal clamping frame 132 Components 2000 NCODRS COUNTRS CONTROLLRS INDICATORS RLAYS PRINTRS CUTTRS
Technical data tico 732 DIMNSIONS VDC 1 Rel/1 Trans VAC 1 Rel/1 Trans VDC 2 Rel/2 Trans VAC 2 Rel/2 Trans For versions with no output, pins 7 9 and 15-17 are not connected. POSSIBL VARIANTS Display Function Outputs Power supply Counter + totalizier no output 12-24 VDC LCD LD Tacho Time counter + totalizer 1 output (1 relay, 1 transistor 100 VAC 115 VAC Shift counter* 2 outputs (2 relays, 2 transistors) 230 VAC Batch counter* ORDR INFORMATION Display Preset 12 24 VDC 24 VAC 115 VAC 230 VAC LCD 0 732 000 0 732 071 0 732 037 0 732 001 LCD 1 0 732 002 0 732 073 0 732 03 1 0 732 003 LCD 2 0 732 012 0 732 078 0 732 049 0 732 013 LD 0 732 018 0 732 080 0 732 055 0 732 019 LD 1 0 732 020 0 732 082 1 0 732 057 0 732 021 LD 2 0 732 030 0 732 087 0 732 067 0 732 031 Important: ly versions with 2 presets or without preset can be used as tachometers. Components 2000 NCODRS COUNTRS CONTROLLRS INDICATORS RLAYS PRINTRS CUTTRS 133