Counters Totalising counters, predetermining counters and totalising timers
|
|
- Camilla Reeves
- 5 years ago
- Views:
Transcription
1 General << Back Counters Totalising counters, predetermining counters and totalising timers Introduction The XBK counters associated with detection products (photo- detectors, inductive sensors, limit switches) or dialogue products (pushbuttons, selector switches, etc) can be used to provide a complementary function of the control system : counting. Functions XBK counters complement the Magelis range of display units and operator dialogue terminals by offering simple display and entry functions. They are fully compatible with labelled Telemecanique detection and man-machine dialogue products. Technology The offer is divided between two technologies : electromechanics and electronics. Electromechanics is used for slow counting applications, of around several tens of hertz, whereas electronics is adapted to counting frequencies of around a kilohertz. These two technologies can be subdivided into three distinct product families : - totalising counters, - predetermining counters, - totalising timers. These three families offer products with varying characteristics : - display capacity, - type and number of outputs, - types of input, - reset to zero option, - adding, subtracting, bidirectional or programmable counting mode, - display in hundredths of an hour (hour counters). This enables the products to be more application-specific. pages 505/ and 505/ pages 505/ and 505/ pages 5055/ and 5055/ 505 Ver.00-EN.fm/
2 General Counters Totalising counters, predetermining counters and totalising timers Applications Totalising counters These are used for counting events from al pulses or contacts. The value is displayed and updated in increments on each new pulse. Application : counting the number of parts In automatic mode : the totalising counter performs this operation in conjunction with a photo- detector, inductive sensor or limit switch, which detects the passing of a part and translates this by adding one unit to the number of parts counted by the totalising counter. In manual mode : the totalising counters performs this operation in conjunction with a pushbutton. A press on the button adds one more unit to the value displayed. This system can be used with a ticket distributor or a manual assembly station. Predetermining counters These are used for counting events from al pulses or contacts. The value is displayed and updated in increments or decrements on each new pulse. They can be used to enter a preset value manually. When this predefined value is reached, they send an al signal. Predetermining counters can be adding or subtracting. Signals Limit switch Supply Applications : upcounting or downcounting the number of parts. The predetermining counter counts the number of parts in the same way as a totaliser. When the selected value is reached, the preset counter, in conjunction with the various sensors, sends a signal to trigger actions, such as stopping a machine or conveyor belt. Stop belt Totalising timers These are used to count and display the time, with a precision of a hundredth of an hour. Applications : they can be used to measure the duration of an action or of the use of a machine. Oven pages 505/ and 505/ pages 505/ and 505/ pages 5055/ and 5055/ 505 Ver.00-EN.fm/
3 Compatibility Counters Totalising counters, predetermining counters and totalising timers Electromechanical technology Totalising counter XBK-T5, XBK-T7 XBK-T6, XBK-T8 XBK-T6 compact Type Input Input Input Input Input Input Supply voltage Ã$ V Ã" 5 V $ V Ã$ V Ã" 5 V Ã$ V Current consumption 70 ma ma ma 0 ma ma 6 ma Power.5 W.5 VA.5 W.5 W.75 VA 0.55 W Inductive proximity sensors/ () -wire photo- detectors Inductive proximity sensors/ () () -wire photo- detectors Photo- detectors, relay output Limit switches/ Pressure switches (volt-free contact) Pushbutton controls (volt-free contact) PLCs: relay outputs PLCs: solid state outputs ELM Contactors/Relays (up to 8 A) PLCs : inputs Pilot lights Predetermining counter Totalising timer XBK-P5 XBK-H7 Type Input Output Reset Input Input Input Supply voltage $ VCC 7 0 V $ V " V " 5 V " 0 V Current consumption 0 ma A max 0.5 A ma 5 ma ma Power.5 W 0 VA max W 0.08 VA 0.56 VA VA Inductive proximity sensors/ () -wire photo- detectors Inductive proximity sensors/ () () () () -wire photo- detectors Photo- detectors, relay output Limit switches/ Pressure switches (volt-free contact) Pushbutton controls (volt-free contact) PLCs: relay outputs PLCs: solid state outputs () ELM Contactors/Relays (up to 8 A) PLCs: inputs Pilot lights TEGO (Reference of plate) () Possible if volt drop <. V (otherwise, boost the supply) () Incompatible with sensors or photocells with protection against overloads < 0 ma () Possible if output current > 0.5 A () Possible with a kω (.5 W) resistor, fitted in parallel APD-AD APD-AD APD-AD APD-AD APD-AD APD-AD Possible combination Combination not possible or not applicable General : pages 505/ and 505/ pages 505/ and 505/ pages 505/ and 505/ pages 5055/ and 5055/ 5056_Ver.0-EN.fm/
4 Compatibility Counters Totalising counters, predetermining counters and totalising timers Electronic technology Totalising counter Predetermning counter totalising timer XBK-T8, XBK-H8 XBK-P6 Type Input Reset to Inputs Relay output Solid state output Sensor zero supply Supply voltage Ã$ V Ã" 0 V Ã" 5 V or Ã" 0 V Voltage State "" State "0" State "" Ã7 5 V min Ã$ - V Ã$ -0 V Ã$ -0 V > $ 5 V < $ 0.7 V > $ 8 V Ã$ 0 V max State "0" State "0" Ã" 50 V max < $ 0.7 V < $ V Resistance 50 kω Current 0 ma max 0 ma min 0 ma max 0 ma max 50 ma max A max Inductive proximity sensors/ (7) -wire photo- detectors Inductive proximity sensors/ () () () (7) -wire photo- detectors Photo- detectors, relay output () () (7) Limit switches/ () () Pressure switches (volt-free contact) Pushbutton controls (volt-free contact) () () PLCs: relay outputs () () PLCs: solid state outputs () ELM Contactors/Relays () () (up to 8 A) PLCs: Inputs (5) (6) (6) Pilot lights TEGO APD-AD APD-AD APD-AD (Reference of plate) APD-AD APD-AD APD-AD () Possible with a 680 Ω resistor fitted in parallel () It is preferable to use contacts designed for low currents () Possible with a 0 kω resistor fitted in parallel () Possible if leakage current at state "0" < 0.5 ma (5) Possible if input current > 0 ma (6) Possible if input current < 0 ma (7) Possible if current consumption < 50 ma APD-AD APD-AD APD-AD APD-AD APD-AD APD-AD APD-AD APD-AD Possible combination Combination not possible or not applicable General : pages 505/ and 505/ pages 505/ and 505/ pages 505/ and 505/ pages 5055/ and 5055/ 5056_Ver.0-EN.fm/
5 Characteristics Counters Totalising counters, predetermining counters and totalising timers Type of device XBK-T totalising counters XBK-H totalising timer Type of display mechanical LCD mechanical LCD Environment Conforming to standards EN 5008-, EN EN 5008-, EN EN 5008-, EN 5008-, EN EN 600 EN 5008-, VDE 05 EN 600 UL, CSA (pending) Product certifications except XBK-T60000U00M UL, C-UL (pending) UL, CSA (pending) UL, C-UL (pending) Temperature Operation C except XBK-T60000U00M : Storage C except XBK-T60000U00M : Degree of protection IP 0 except IP 5 IP 65 IP 5 according to IEC 59 XBK-T60000U00M : IP 65 Vibration resistance 5 gn (0 to 50 Hz) gn (0 to 50 Hz) gn (0 to 50 Hz) gn (0 to 50 Hz) according to IEC Shock resistance 0 gn (6 ms) 0 gn (8 ms) 0 gn ( ms) 0 gn (8 ms) according to IEC Protection against shocks Class II according to IEC 56 Mounting and fixing Flush-mounting element Flush-mounting unit fixed Flush-mounting unit fixed by a self-locking by a clamp clamp Connection By AMP lugs on a On screw terminal block cable connector Characteristics Supply voltage V c ± 0 % Battery a ± 0 % 50 Hz Battery c ± 0 % a 5 ± 0 % 50 Hz a 5 ± 0 % a 0 ± 0 % 50 Hz Consumption W/VA XBK-T50000U0M, XBK-T M : 0.56 XBK-T50000U08M and XBK-T M : XBK-T70000U00M :.5 XBK-T M : 0.08 XBK-T50000UM :.5 XBK-T60000U0M and XBK-T80000U00M :.5 XBK-T60000UM :.75 XBK-T60000U00M : 0.55 Counting frequency Hz 0, 0, Backup capacity Permanent 7 years Permanent 7 years Number of digits 5, 6, 7 or Precision of display h h Character height mm Counting mode Adding Adding Adding /00 of an hour (Input resistance : 50 kω) Reset to zero With or without With Without With Type of reset to zero Manual Manual with Manual with locking locking Inputs Function Count Enable Type Contact Transistor : PNP 8 V Contact Transistor : PNP 8 V or NPN 0.7 V or NPN 0.7 V Amplitude V ± 0 V max ± 0 V max Mechanical life 0 million pulses except XBK-T60000U0M and T80000U00M : 00 million Minimum length of pulse ms 5 at 0 Hz, 0.07 at 7.5 khz General : pages 505/ and 505/ pages 505/ and 505/ pages 5055/ and 5055/ Compatibility : pages 5056/ and 5056/ 505 Ver.00-EN.fm/
6 Characteristics Counters Totalising counters, predetermining counters and totalising timers Type of device XBK-P5 XBK-P6 Type of display Mechanical LED or LCD Environment Conforming to standards EN and EN 5008-, EN 600 Product certifications XBK-P5pppDppM : CSA (pending) XBK-P5pppUppM : UL/CSA (pending) UL, C-UL (pending) Temperature Operation C Storage C Degree of protection according to IEC 59 IP 0 IP 65 Vibration resistance 5 gn (0 to 50 Hz) gn (0 to 50 Hz) according to IEC according to IEC Shock resistance 0 gn (6 ms) 0 gn (8 ms) according to IEC according to IEC Protection against Class II according to IEC 56 shocks Mounting and fixing Removable, flush-mounting element Flush-mounting unit with fixing by self-locking clamp Fixing by screws on the front plate using needle screws Characteristics Supply voltage V c ± 0 % c or a 0 ± 0 % or a 5 ± 0 % Sensor supply voltage V None c to (50 ma max) for XBK-P6pp0GE or XBK-P6pp0GE Consumption.5 W 50 ma c V, 50 ma a 0 or a 5 V Counting frequency Hz (500 on bi-directional counting) Number of digits 5 6 Display capacity Character height mm 7.6 (LED) or 9 (LCD) Number of presets or Display of the preset Adding (continuous) Non continuous or subtracting (non continuous) Counting mode Adding or subtracting 5 programmable modes : - single counter input, - single counter with phase discriminator, - differential inputs, - summing inputs, - counting direction input. (Counter input resistance 5 kω) Reset Adding from zero modes : reset to zero and reset to the preset value Subtracting from the preset value Type of reset Manual or manual and Manual, and automatic Type of input signals Contact (0 VA/0 V/ A max) Transistor : PNP 8 V or NPN V Amplitude ± 0 V max Type of outputs Contact (volt-free) Changeover relay (response time 5 ms) : c 5 V < Uc < c 0 V a 5 V < Uc < a 50 V 0 ma < I < A PNP transistor : at V, 0 ma max Connection By AMP lugs on a cable connector On screw terminal block Minimum length of ms 7 at 0 Hz counting pulse 0. at 5 khz General : pages 505/ and 505/ pages 505/ and 505/ pages 5055/ and 5055/ Compatibility : pages 5056/ and 5056/ 505 Ver.00-EN.fm/
7 References Counters Totalising counters, predetermining counters and totalising timers Totalising counters With mechanical display Supply Number Counting Type of Reference Weight voltage of display frequency reset to zero digits V Hz kg $ 5 0 Manual XBK-T50000U0M None XBK-T60000U00M 0.00 XBK-T50000U//M 5 Manual XBK-T60000U0M None XBK-T70000U00M 0.00 XBK-T60000U00M 8 5 None XBK-T80000U00M 0.50 $ 5 0 None XBK-T50000U08M 0.00 " Manual XBK-T50000UM 0.00 XBK-T60000U/M 6 0 Manual XBK-T60000UM 0.00 With LCD display Supply Number Counting Type of Reference Weight voltage of display frequency reset to zero digits V khz kg XBK-T70000U00M Battery Manual XBK-T800UE with locking Totalising timers XBK-T80000U00M With mechanical display (max. display capacity : h) Supply Number Supply Type of Reference Weight voltage of display frequency reset to zero digits V Hz kg " 7 50 None XBK-H M XBK-T800UE " None XBK-H M " None XBK-H M XBK-H /M XBK-H80000E With LCD display (max. display capacity : h) Supply Number Display Type of Reference Weight voltage of display mode reset to zero digits V kg Battery 8 /00 of an hour Manual XBK-H80000E with locking General : pages 505/ and 505/ pages 505/ and 505/ pages 5055/ and 5055/ Compatibility : pages 5056/ and 5056/ 505_Ver.0-EN.fm/
8 References Counters Totalising counters, predetermining counters and totalising timers Subtracting predetermining counters with mechanical display Supply Number Counting Number Type Reference Weight voltage of display frequency of of digits presets reset V Hz kg $ 5 5 Manual XBK-P5000D0M 0.00 Manual and XBK-P5000D0M 0.0 Adding predetermining counters with mechanical display XBK-P5000D/0M $ 5 5 Manual XBK-P5000U0M 0.00 Manual and XBK-P5000U0M 0.0 Predetermining counters with LCD display Supply Number Counting Number Type Reference Weight voltage of display frequency of of digits presets reset V khz kg XBK-P5000U/0M $ 6 5 Manual, XBK-P60G0E 0.50 and automatic Manual, XBK-P60G0E 0.50 and automatic " Manual, XBK-P60GE 0.50 and automatic XBK-P6/0G/E XBK-P6/0G/E Manual, XBK-P60GE 0.50 and automatic " Manual, XBK-P60GE 0.50 and automatic Predetermining counters with LED display Manual, XBK-P60GE 0.50 and automatic Supply Number Counting Number Type Reference Weight voltage of display frequency of of digits presets reset V khz kg $ 6 5 Manual, XBK-P60G0E 0.50 and automatic Manual, XBK-P60G0E 0.50 and automatic " Manual, XBK-P60GE 0.50 and automatic Manual, XBK-P60GE 0.50 and automatic General : pages 505/ and 505/ pages 505/ and 505/ pages 5055/ and 5055/ Compatibility : pages 5056/ and 5056/ 505_Ver.0-EN.fm/
9 Dimensions Counters Totalising counters, predetermining counters and totalising timers XBK-T50000U//M Flush-mounting XBK-T60000U00M Flush-mounting XBK-T70000U00M e e, 6, 75,5 8,5 7,7, , e : panel thickness, mm < e <.5 mm. XBK-T60000U/M XBK-T80000U00M Flush-mounting (common) = = 0, e 0, 5 0, ,5 XBK-H /M Flush-mounting XBK-T800UE Flush-mounting XBK-H80000E e 5 5,5 6,5 e : panel thickness, < mm. XBK-P5000D/0M 5 0 e : panel thickness, < mm. XBK-P50000U/0M 88, ,5 0, 0, Flush-mounting (common) XBK-P6//0G/E Flush-mounting 60 e = 55 = 55 9,5 0,7 5 5 e : panel thickness, < mm. General : pages 505/ and 505/ pages 505/ and 505/ pages 505/ and 505/ Compatibility : pages 5056/ and 5056/ 5055_Ver.00-EN.fm/
10 Connections Counters Totalising counters, predetermining counters and totalising timers XBK-T50000U//M XBK-T70000U00M -/ XBK-T80000U00M XBK-T60000U/M XBK-T60000U0M -/ XBK-T80000U00M XBT-T800UE XBK-H80000E XBK-P5000D/0M XBK-P5000U/0M PNP NPN Reset Count 0 V Keylock 0 0 Reset Count 0 V Keylock XBK-P6//0G/E $ V $ V " 0 V " 5 V -wire sensor/detector type XS, XU R = 0 kω XBKP6//0G0E default configuration (PNP) Black 5-wire sensor/detector type XS, XU Blue Red Brown (NO) or Orange (NC) XBKP6//0G0E default configuration (PNP) -wire sensor/detector type XS, XU 0 R = 0 kω XBKP6//0GE or GE default configuration (PNP) $ V " 0 V " 5 V Black 5-wire sensor/detector type XS, XU Blue Red Brown (NO) or Orange (NC) 0 XBKP6//0GE or GE default configuration (PNP) -wire sensor/detector or photocell relay or limit switch or pushbutton A A Control relay type CA 7 XBKP6//0G0E default configuration (PNP) 6 General : pages 505/ and 505/ pages 505/ and 505/ pages 505/ and 505/ Compatibility : pages 5056/ and 5056/ 5055_Ver.00-EN.fm/
11 Characteristics Zelio Count - counters 0 Electronic totalising counters, x, 8 digits, LCD Technical characteristics Function Impulse counter Display 8 digit LCD Digit height mm 7 Counting capacity Input characteristics voltage levels Terminals - 5 V a / c 5 50 Terminals 5-6 V a 0 Reset to zero characteristics () Front panel Dipswitch n to OFF Inhibited Dipswitch n to ON Enabled Voltage Terminals - V a / c 5 50 Terminals - V a 0 Counting speed characteristics Slow counting Hz 0 Minimum impulse duration Low level ms High level ms Input levels V c 0 Input impedance kω.5 min Supply characteristics alkaline batteries Life years lithium battery Life 8 years Supply can be switched off via Dipswitch n located on the underside of the device General characteristics Material Self-extinguishing Connection By 6 screw terminals on back of the device Clamping capacity mm x.5 Fixing By yoke Front panel degree of protection IP 66 Temperature limits Operation C Storage C Insulation resistance Conforming to IEC 55.5 MΩ 00 (c 500 V) Di strength Conforming to IEC V/50 Hz/ min Conforming to standards VDE 00, IEC 66,, 55., 55.5, 80., 80. Approvals c UL us, CSA () The reset is galvanically isolated from the counting input. page 856/ page 856/ Schemes : pages 856/ and 8565/ 856_Ver.00-EN.fm/
12 References, dimensions, scheme Zelio Count - counters 0 Electronic totalising counters, x, 8 digits, LCD b 8-digit LCD display; digit height 7 mm b Powered by alkaline batteries or lithium battery b Counting inputs : solid state (c 0 V) or voltage (up to c 0 V) b Dimensions DIN - x mm b Reset on front panel or external with inhibit facility 5608 References Totalising counters, LCD x Description Reference Weight kg Voltage input, lithium battery RC RC Accessories Description Dimensions Reference Weight kg Adaptors for 5x50 mm (dimensions 9x5 mm) RC panel cut-out 5x5 mm (dimensions 5x5 mm) RC Ø 50 mm (dimensions Ø 7 mm) RC Dimensions RC Panel cut-out (Max. thickness 0mm) unit units,6 0,6, , - 0 0,8 6 RC RC RC , , 9 8, Scheme (other schemes on page 8565/) V ~ 5. 50V ~/ V 0V ~/ ~ Terminals - Reset a 0 V -0Vreset - Reset a/c 5 50 V -a/c 5 50 V 5-0V 6-a 0 V Reset inputs Start/stop inputs page 856/ 856_Ver.00-EN.fm/
13 Characteristics, schemes Zelio Count - counters 0 Electronic total/partial impulse counters, x, 8 digits, LCD Technical characteristics Function Impulse counter Display 8 digit LCD Digit height mm 7 Counting capacity Input characteristics Counter type RC RC Input type counting input by volt-free contact or galvanically isolated counting input NPN or PNP open-collector transistor (terminals - ) Minimum time closed ms 0 Voltage Terminals - 5 V a / c 5 50 Terminals 5-6 V a 0 Reset to zero characteristics () Front panel External (total counter) Partial counter always enabled Volt-free contact or NPN or PNP opencollector transistor (terminals - ) Minimum time closed ms 0 0 Voltage Terminals - V a / c 5 50 Terminals - V a 0 Counting input characteristics Counting speed (selectable with dispwitch n ) Hz or 00 Slow counting (minimum impulse duration) Fast counting (minimum impulse duration) Supply characteristics Low level ms 5 High level ms 5 Low level ms 5 High level ms 5 lithium battery Life 5 years Supply can be switched off via Dipswitch n located on the underside of the device General characteristics Material Connection Self-extinguishing By 6 screw terminals on back of the device Clamping capacity mm x.5 Fixing By yoke Front panel degree of protection IP 66 Temperatures Operation C Storage C Conforming to standards VDE 00, IEC 66, IEC, IEC 55., IEC 55.5, IEC 80., IEC 80. Approvals c UL us, CSA () The reset is galvanically isolated from the counting input. Schemes (other schemes on pages 8565/ and 8565/) RC RC NC NC. 0V ~ 5. 50V ~/ V 0V ~/ ~ General reset inputs Counting inputs General reset inputs Counting inputs Terminals - General reset input - General reset common - Count common -Counting 5 - Not connected 6 - Not connected Terminals -Reseta 0 V - General reset common -Reseta/c 5 50 V -a/c 5 50 V 5 - Count common 6-a 0 V page 856/ page 856/ 856_Ver.00-EN.fm/
14 References, dimensions Zelio Count - counters 0 Electronic total/partial impulse counters, x, 8 digits, LCD b Partial or total count display b Counting capacity : v partial : v total : b Counting inputs and reset inputs : v RC : solid state v RC : voltage b Decimal point b Integral module for voltage inputs (a / c 5 50 V, a 0 V) b Powered by lithium battery. Life : 5 years b Front panel reset for "partial" count b Front panel or al reset for total count b Accessories for panel cut-out 5 x 50, 5 x 5, Ø References Total/partial impulse counters, LCD x Description Reference Weight kg Solid state input RC Voltage input RC RC Accessories Description Dimensions Reference Weight kg Adaptors for 5x50 mm (dimensions 9x5 mm) RC panel cut-out 5x5 mm (dimensions 5x5 mm) RC Ø 50 mm (dimensions Ø 7 mm) RC Dimensions RC p0 Panel cut-out (Max. thickness 0mm) unit units,6 0,6, , - 0 0,8 6 RC RC RC , , 9 8, page 856/ Schemes : page 856/ 856_Ver.00-EN.fm/
15 Characteristics Zelio Count - counters 0 Electronic totalising counters, hour counters, chronometers x, 6 or 8 digits, LCD Counter type RC RC Technical characteristics Functions Impulse counter Hour counter/chronometer Solid state input Solid state Solid state Display 8 digit LCD 6digitLCD Digit height mm 7 7 Counting capacity Time ranges h min s 0 99 h 59 min 59 s Time base Quartz (precision ± 50 ppm) Possibility of reloading current value Yes Supply lithium battery Life 8 years 5years Input characteristics Volt-free contact Start/Stop input 0 ms minimum (terminals -5) Reset input 00 ms minimum (terminals -) Prog. input (terminals -) enable Reset input (terminals -) Slow input In.L Volt-free contact or transistor Hz 0 max TOFF ms min TON ms min Current output µa 5 max Leakage current in OFF state µa 0. max Residual voltage V 0. max NPN collector Fast input khz 7max In.H TOFF µs 70 min TON µs 70 min Level 0 V c 0 Level V c 0 Current consumption ma 6maxatc V Reset to zero : Reset Volt-free contact or transistor Volt-free contact or transistor NPN open collector ms minimum 00 minimum Enable reset Front panel Front panel Electromagnetic environment characteristics Radiated field Conforming to IEC Level,0V/M,6MHztoGHz Fast transients Conforming to IEC Level, kv Damped oscillatory wave Conforming to IEC 55- Level, kv Electrostatic discharge Conforming to IEC Level, 8 kv Operating characteristics Material Self-extinguishing Connection by screw terminals on back of the device 5 terminals Clamping capacity mm x.5 Fixing By yoke Degree of protection IP 6 Temperature limits Operation C 0 55 Storage C Conforming to standards VDE 00, IEC 66,, 55., 55.5, 80., 80. Approvals c UL us, CSA page 856/ page 856/ Schemes : page 856/ 856_Ver.00-EN.fm/
16 References, dimensions, schemes Zelio Count - counters 0 Electronic totalising counters, hour counters, chronometers x, 6 or 8 digits, LCD 5608 b 8 or 6 digit LCD display, digit height 7 mm b Totalising counter : v 7 khz and 0 Hz inputs v Maximum counting capacity : impulses b Hour counter/chronometer : v Start/stop inputs v time ranges : hours min s - 99 h 59 min 59 s b Powered by lithium battery. v Reset from front panel or remote reset References Totalising counters, LCD x Description Reference Weight kg Impulse counter RC Hour counter/chronometer RC RC Accessories Description Dimensions Reference Weight kg Adaptors for panel cut-out 5x50 mm (dimensions 9x5 mm) RC x5 mm (dimensions 5x5 mm) RC Ø 50 mm (dimensions Ø 7 mm) RC Dimensions RC p0 08,6 7,,,8 Panel cut-out - 0, 0 0,8-0,5 0 0 ;;; yyy ; y ;;; yyy ; y RC RC RC , , 8, Schemes RC RC In. L En.R In. H Reset Terminals - Reset input - Enable Reset - Slow counting -OV 5 - Fast counting 5 08, Fast counting input Slow counting input and reset Enable Reset input 5 Enable Reset Prog. Reset Start/Stop 00 ms Terminals - Reset input - Enable Reset - Common -Prog. 5 - Start/Stop,,5 08 H 08 H Start/Stop input Prog. Reset Enable Reset input page 856/ 856_Ver.00-EN.fm/
17 Characteristics Zelio Count - counters 0 Electronic hour counters, x, 6 digits, LCD Technical characteristics Function Hour counter Display 6 digit LCD Digit height mm 7 Time ranges h min s 0 99 h 59 min 59 s Time base Quartz (precision ± 50 ppm) Possibility of reloading current value Yes Input characteristics Input type start/stop input Voltage Terminals - 5 V a / c 5-50 Terminals 5-6 V a 0 Minimum impulse time a ms 50 c ms 5 Reset characteristics () Front panel Dipswitch n to OFF Inhibited Dipswitch n to ON Enabled Voltage Terminals - V a / c 5-50 Terminals - V a 0 Minimum impulse time ms 00 Supply characteristics lithium battery Life 5 years Supply can be switched off via Dipswitch n located on the underside of the device General characteristics Material Self-extinguishing Connection By 6 screw terminals on back of the device Clamping capacity mm x.5 Fixing By yoke Front panel degree of protection IP 66 Temperature limits Operation C Storage C Conforming to standards VDE 00, IEC 66,, 55., 55.5, 80., 80. Approvals c UL us, CSA () The reset is galvanically isolated from the counting input. page 856/ page 856/ Schemes : page 856/ 856_Ver.00-EN.fm/
18 References, dimensions, scheme Zelio Count - counters 0 Electronic hour counters, x, 6 digits, LCD b Inputs and reset : voltage b Integral module for voltage inputs(a or c 5 50 V, a 0 V) b time ranges : v h min v s - 99 h 59 min 59 s b Possibility of reloading current value b Powered by lithium battery. Life 5 years b Reset on front panel or external with inhibit facility References RC Hour counters, LCD x Description Reference Weight kg Voltage input RC Accessories Description Dimensions Reference Weight kg Adaptors for 5x50 mm (dimensions 9x5 mm) RC panel cut-out 5x5 mm (dimensions 5x5 mm) RC Ø 50 mm (dimensions Ø 7 mm) RC Dimensions RC Panel cut-out (Max. thickness 0 mm) unit units,6 0,6, , - 0 0,8 6 RC RC RC , , 9 8, Scheme (other schemes on page 8565/) V ~ 5. 50V ~/ V 0V ~/ ~ Terminals - Reset a 0 V - Reset common - Reset a/c 5 50 V -a/c 5 50 V 5 - Start/stop common 6-a 0 V A Reset inputs B Start/stop inputs page 856/ 856_Ver.00-EN.fm/
19 Schemes Zelio Count - counters 0 Counters x Connection schemes RC Fast counting input Counting and general reset input Voltage -0V Volt-free contact NPN transistor or -wire NPN proximity sensor () (RC ) NPN -0V OV PNP transistor or -wire PNP proximity sensor () (RC ) -0V PNP -wire proximity sensor -0V R() OV -wire proximity sensor -0V OV R() () For sensor with leakage current 0. ma () R = 70 Ω /Ω for a -wire sensor with leakage current.5 ma page 856/ 8565_Ver.00-EN.fm/
20 Schemes Zelio Count - counters 0 Counters x Connection schemes RC , RC , RC Voltage Counting input RC Start/Stop input RC Reset RC , RC , RC V~/ -0V~ 5 6-0V~ 5-50V~/ Live contact 5-50V~/= -0V~ 5 6-0V~ 5-50V~/ PNP transistor or -wire PNP proximity sensor () 5-50V 5-50V PNP PNP OV 5 OV NPN transistor or -wire NPN proximity sensor () 5-50V 5-50V NPN NPN OV 5 OV -wire proximity sensor 0V max 0V max R() 5 R() OV OV -wire proximity sensor 0V maxi 0V maxi OV R() 5 OV R() () For sensor with leakage current 0. ma () R = 70 Ω /Ω for a -wire sensor with leakage current.5 ma pages 856/ to 856/ 8565_Ver.00-EN.fm/
21 Functions Zelio Count - counters 0 Multifunction counters with display Models RC and RC Input modes Input mode UP DN PNP : count on rising edge NPN : count on falling edge n n- n- n- n- n-5 n-6 Input IN Display Input IN Display IND CUMUL DIR Up DOWN Up n n - n - n - n - n - n n - n n- n - n - n - 5 n Input IN count in the direction of the cycle Input IN count in the direction of the cycle Input IN input pulses Input IN count in the opposite direction from the cycle Input IN count in the opposite direction Input IN reversal of counting direction Display (O...P) channel up/down counters from the cycle Display (O...P) channel up/down counters Display (P...O) channel up/down counters Display (O...P) channel up/down counters Display (P...O) channel up/down counters Display (P...O) channel up/down counters PH PH PH n n - n - n - n - n - n n - =0 Input IN (signals 90 out of phase) Input IN (signals 90 out of phase) Display (O...P) Display (P...O) Output modes Single cycle =n n - n - n - n- n - n - 0 n n- n- n- n- n-5 n- n- n- n- Input IN counts on rising and falling edges Input IN direction of count reversed if IN in advance of IN Display (O...P) Display (P...O) presets n n- n- n- n- n-5 n-6 n-7 Input IN counts on rising and falling edges Input IN counts on rising and falling edges, direction of count reversed if IN in advance of IN Display (O...P) Display (P...O) PR 0 P-----P P P- P P- P P PR P- P P P P P P----- ON OFF PR 0 P P P- P P P----- P P 0 PR P- P P P--- P t P- P t ON OFF Repetitive cycle Maintained PR 0 P P P P n n P P 0 PR P n n t ON OFF Pulsed (transient pulse) (t = s) Pulsed with auto Reset to value of P (or P for preset) (t = 500 ms) t = 0. s to 9.9 s for multifunction Batch counter function Principle P is the batch preset When P is displayed, the value displayed on the upper digits represents the current counter value (reset to P). In this configuration the RST key on the front panel of the device reinitialises the current value. When P (batch preset) is displayed, the value displayed on the upper digits represents the value of the Batch counter. In this configuration the RST on the front panel of the device resets the batch counter. An "al" reset (RST terminal) still resets the current counter value and that of the batch counter. Example On a packing line, bottles need to be counted Current counter into packs of 6 bottles and then despatched in OUT a box containing a batch of packs. Batch counter 0 0 P : current counter preset value : OUT P : batch counter preset value : 0000 Reset pages 8567/ and 8567/ pages 8568/ and 8568/ pages 8568/ and 8568/ Schemes : pages 8568/ and 8568/ 8566_Ver.00-EN.fm/
22 Functions Zelio Count - counters 0 Multifunction counters with display Models RC and RC Totalising counter function On multifunction version b Totalising counter reset via front panel only b Current value reset via front panel and al Signal measurement period Time TR Time TL Start of measurement Signal to be measured End of measurement Tachometer function Measurement principle Measurement begins on a rising edge of the signal to be measured The measurement time is greater than TR, but less than TL. Measurement stops at the end of the current period () after TR. If the period () does not end before TL, the measurement result will be zero (0). The outputs are updated at the end of each measurement according to the selected output mode. b Maintained output : output active if the measured speed is greater than the preset speed b Pulsed output : output activated during time T, when the preset threshold is crossed Measurement accuracy : 00 (00/TR) PPM Example : for TR = s : 00 PPM (0.0 %). Speed Speed P P P P 0 Out () Out t 0 Out () Out t Out () Out Out () Out 00 rev/min 0 m/s () Maintained () Pulsed output Application example You wish to display a linear speed of.00 m/s for a drive pulley rotating at 00 rev/min. A sensor on this pulley delivers one pulse, per revolution, i.e. : Ns Coef RPX V = n Required display : V =.00 (result in m/s RPX = ). Given that : n = 00 Ns = = 5 60 V n 00 Dwhere Cœf = Cœf = Ns RPX = 5 0 In addition, the decimal point is positioned in the hundreds (xxxx.xx). Selection of TR : you wish the measurement to be updated every seconds TR = s. Select TL > TR, for example TL = s. The tachometer function can also be used to calculate a flow rate. Chronometer function (precision : 50 ppm) PROG IN Input IN Display (0...PR), channel pulse measurement Display (PR...0), channel pulse measurement T T Tn --- Tn - T T T T Tn - (T T) PROG IN Input IN Display (0...PR), channel period measurement Display (PR...0), channel period measurement 0 Tn T T Tn - T T T T Tn - (T T) PROG IN Input IN (start counting) Input IN (stop counting) Display (0...PR), measurement on separate channels Display (PR...0), measurement on separate channels 0 Tn T T T Tn - T T T Tn - (T T) pages 8567/ and 8567/ pages 8568/ and 8568/ pages 8568/ and 8568/ Schemes : pages 8568/ and 8568/ 8566_Ver.00-EN.fm/
23 Characteristics Zelio Count - counters 0 Preselection and multifunction counters Models RC and RC Counter type RC ppp RC ppp Technical characteristics Functions Number of presets Back-lit or red illuminated display Mulltifunction Preselection up/down counters Counters, 'Batch' counters, tachometers and chronometers or Current value 5 digits 6digits Preset 5 digits 6digits Digit height Current value mm 8 0 Preset mm 6 Display capacity Simultaneous readout of count value and one preset Yes Yes Input characteristics Counters, 'Batch' counters, totalising counters, tachometers and chronometers Inputs counting inputs IN, IN counting inputs IN, IN, inhibit input Input modes (see page 8566/) UP, DN, DIR, IND, CUMUL PH, PH, PH Input by contact Voltage or solid state for -wire and -wire detection using external resistor (NPN or PNP depending on wiring) Counting speed Counters 5 khz or 0 Hz.5 khz PH Voltage or solid state (NPN/PNP depending on wiring) 5 khz (.5 khz in phase x ) 0 Hz in debounce mode Mulltifunction Counter Tachometer Counter Tachometer Totalising counter UP, DOWN, DIR khz IND, CUMUL (IN, IN non khz simultaneous) IND, CUMUL (IN, IN simultaneous) khz 5 5 PH, PH khz 5 (except in Batch mode) : khz) 5 (except in Batch mode) : khz).5 PH khz Low level V c 0 High level V c 0 Impedance kω 0 Reset characteristics Reset to zero or to preset value Front panel Electrical If not protected in programming phase By contact, voltage or solid state (NPN or PNP depending on wiring) By contact, voltage or solid state (NPN or PNP) Minimum pulse time ms 5 Low level V c 0 High level V c 0 Impedance kω 0 Option to protect against reset from front panel Yes Scale factor (each input pulse is multiplied by this figure) Decimal point selectable for ease of reading xxxxx, xxxx.x, xxx.xx, xx.xxx xxxxxx, xxxxx, x, xxxx, xx, xxx.xx, xx.xxxx Sensor supply a version c or 00 V c version Un- V/00 ma Configuration and current value saved In EEPROM memory Functions : pages 8566/ and 8566/ pages 8568/ and 8568/ pages 8568/ and 8568/ Schemes : pages 8568/ and 8568/ 8567_Ver.0-EN.fm/
24 Characteristics (continued) Zelio Count - counters 0 Preselection and multifunction counters Models RC and RC Counter type RC ppp RC ppp Output characteristics Solid state outputs - Type NPN open collector - Maximum current ma 00 - Maximum voltage V c 0 - Voltage drop V <.5 - Response time µs < 50 Relay outputs - Type N/O contacts or solid state depending on model C/O contacts solid state - Rated current A - Maximum voltage V a 50 - Maximum breaking capacity (resistive) AC- VA Minimum current ma Response time ms < 0 - Mechanical life x0 6 operating cycles x0 7 operating cycles - Electrical life at I max. AC- x0 5 x0 5 - Output modes : maintained or pulsed (fixed or adjustable pulse duration)) t = s t = s - Single cycle or repetitive (immediate auto reset) Yes Supply (min/max values) V c 0 0,a0 55, a Maximum consumption c version W <5 a 50/60 Hz version VA 0 < General characteristics Immunity to microbreaks c 0 0 V version ms 0 a 0 55 V version ms 0 a V version ms 0 Relative humidity (without condensation) 95 % Altitude m Insulation (IEC 66-) kv.5 Standards Conforming to IEC Level Conforming to IEC Level Conforming to IEC Level Conforming to IEC Level Conforming to IEC 550/ group Class A Vibration withstand on axes conforming to IEC Hz / 0.5 mm Material Self-extinguishing Connection Screw terminals Clamping capacity mm x.5 Front panel fixing With bracket Front panel protection IP 5 Front panel seal Yes Temperature limits Operation C 0 55 Storage C Approvals c UL us, CSA Functions : pages 8566/ and 8566/ pages 8568/ and 8568/ pages 8568/ and 8568/ Schemes : pages 8568/ and 8568/ 8567_Ver.0-EN.fm/
25 References, dimensions, schemes Zelio Count - counters 0 Electronic preselection and multifunction counters, x, 5 digit, LCD or LED References Preselection and multifunction up/down counters x Functions : counter, batch counter, tachometer, chronometer Counting input modes UP, DN, IND, CUMUL, DIR, PH, PH, PH Time base : 99 h 59 min, 99 min 59 s, s, h presets Description Supply voltage Outputs Reference Weight kg Back-lit LCD display a V N/O RC solid state RC a 0 55 V N/O RC solid state RC RC c 0 0V N/O RC solid state RC Red LED display a V N/O RC solid state RC a 0 55 V N/O RC solid state RC RC Dimensions Display c 0 0V N/O RC solid state RC Panel cut-out P RST P RST Reset Access to all parameters in Prog. mode Incrementation of figures and multipliers selection of a parameter value Connection schemes RC p, RC p RC p, RC p Supply Supply Functions : pages 8566/ and 8566/ pages 8567/ and 8567/ 8568_Ver.00-EN.fm/
26 References, dimensions, schemes Zelio Count - counters 0 Electronic preselection and multifunction counters, 7 x 7, 6 digit, LCD or LED References Preselection and multifunction up/down counters 7 x 7 Functions : counter, batch counter, tachometer, chronometer, totalising counter Counting input modes UP, DN, IND, CUMUL, DIR, PH, PH, PH Time base : 99 h 59 min, 99 min 59 s, s, h, h, min. presets Description Supply voltage Outputs Reference Weight kg Back-lit LCD display a V C/O solid state RC a 0 55 V C/O solid state RC RC c 0 0V C/O solid state RC Red LED display a V C/O solid state RC a 0 55 V C/O solid state RC RC c 0 0V C/O solid state RC Dimensions Display Panel cut-out 7 P OUT P OUT P P RST P P RST Reset / Access to all parameters in Prog. mode Incrementation of figures and multipliers selection of a parameter value Connection schemes RC p, RC8769p Supply Functions : pages 8566/ and 8566/ pages 8567/ and 8567/ 8568_Ver.00-EN.fm/
Count - counters 5. Selection guide 5 XBK T81030U33E RC XBK RC XBK T60000U00M XBK T60000U11M XBK T80000U00M XBK T70000U00M 5/2
Selection guide Count - counters Function Totalising counters Display type Mechanical LCD Font panel dimensions (h x w) in mm 0 x 0 x. 0 x 60 x Number of display digits 6 digits or 6 digits (depending
More informationCounters. General. Totalising counters, predetermining counters and totalising timers. Introduction. Functions. Technology
General Counters Totalising counters, predetermining counters and totalising timers Introduction The XBK counters associated with detection products (photo- detects, inductive senss, limit switches) dialogue
More information02/11/2015
35 mm - 1 Relay 8A OUR3 Part number 88867103 Multi-function or mono-function Multi-range Multi-voltage Relay output 1 or 2 : 8 A - 250 V (10 A UL) LED status indicator Option of connecting an external
More informationCount/Time Totalizers
/Time Totalizers Compact or Time Totalizers with Easy-to-Read and NEMA 4 Protection High-visibility, 8.5 mm negative transmissive LCD. NEMA 4 when used in conjunction with Y92S-32 rubber gasket supplied
More informationMultifunctional counter tico 772/773/774
Universally applicable as a tachometer, timer, shift counter, batch counter Easy to operate Four different backlight colours Intensity of backlighting can now be adjusted Large, clearly readable 48 x 48
More information02/11/2015
35 mm - 2 Relays 8A PL2R1 Part number 88867455 Multi-function or mono-function Multi-range Multi-voltage Relay output 1 or 2 : 8 A - 250 V (10 A UL) LED status indicator Option of connecting an external
More informationCompact Preset Counter
signo 721 Compact Preset Counter 1 or 2 presets Prescaler with output for connection of a totalizing counter Large, 5-digit LD display Connection by plug-in screw terminals Variety of programming possibilities
More informationPreset counters, electronic
The Codix 716 / 717 can be used universally. These preset pulse, tachometers or preset timers with up to 2 presets can solve a wide variety of control and monitoring tasks in every application. With their
More informationRE17RAMU on-delay timing relay - 1 s..100 h V AC - 1 OC
Characteristics on-delay timing relay - 1 s..100 h - 24..240 V AC - 1 OC Main Range of product Product or component type Discrete output type Width Device short name Time delay type Time delay range Nominal
More informationRE17RMMW time delay relay 10 functions - 1 s..100 h V AC/DC - 1 OC
Characteristics time delay relay 10 functions - 1 s..100 h - 12..240 V AC/DC - 1 OC Main Range of product Product or component type Discrete output type Width Device short name Time delay type Time delay
More informationRE17RMMW time delay relay 10 functions - 1 s..100 h V AC/DC - 1 OC
Characteristics time delay relay 10 functions - 1 s..100 h - 12..240 V AC/DC - 1 OC Main Range of product Product or component type Discrete output type Width Device short name Time delay type Time delay
More informationRE17RCMU off-delay timing relay - 1 s..100 h V AC - 1 OC
Characteristics off-delay timing relay - 1 s..100 h - 24..240 V AC - 1 OC Main Range of product Product or component type Discrete output type Width Device short name Time delay type Time delay range Nominal
More informationem4 local - Robust Specific characteristics Part number
em4 em4 local em4 local Very compact and easy to program nanoplc Save time in designing your application using the most intuitive graphical function block language of the market Measure accurately your
More information22/10/2012
22.5 mm DIN rail mounting TUR1 Part number 88865105 Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator Option of connecting an external power supply
More informationRE17RAMU on-delay timing relay - 1 s..100 h V AC - 1 OC
Characteristics on-delay timing relay - 1 s..100 h - 24..240 V AC - 1 OC Complementary Contacts material Control type [Us] rated supply voltage Voltage range Main Range of product Product or component
More information"Modular" versions designed for application-specific functions LCD with 4 lines of 18 characters and configurable backlighting
Smart "Compact" range with display CD12 Smart Part number 88974043 "Modular" versions designed for application-specific functions LCD with 4 lines of 18 characters and configurable backlighting Type Input
More informationRE17LLBM asymmetrical flashing relay s V AC - solid state output
Characteristics asymmetrical flashing relay - 0.1..1 s - 24..240 V AC - solid state output Product availability : Non-Stock - Not normally stocked in distribution facility Price* : 75.00 USD Main Range
More informationRE17RMMW time delay relay 10 functions - 1 s..100 h V AC/DC - 1 OC
Characteristics time delay relay 10 functions - 1 s..100 h - 12..240 V AC/DC - 1 OC Product availability : Stock - Normally stocked in distribution facility Price* : 75.00 USD Main Range of product Product
More informationCustom "Compact" range with display CD20 Custom Part number
Custom "Compact" range with display CD20 Custom Part number 88974051 "Modular" versions designed for Custom application-specific functions (Custom functions) LCD with 4 lines of 18 characters and configurable
More informationRE22R2MMU Multifunction Timer Relay - 24VDC/ V AC - 2 C/O
Product data sheet Characteristics RE22R2MMU Multifunction Timer Relay - 24VDC/24..240 V AC - 2 C/O Main Range of product Product or component type Discrete output type Device short name Nominal output
More informationPROGRAMMABLE DIGITAL TIMER ELIRO (33 Functions): V7DFTS3
PROGRAMMABLE DIGITAL TIMER ELIRO (33 Functions): V7DFTS3 Basic Features: Luxurious look with 2x4 7-Segment Display. 33 Default Modes. Modes can be Customized as per user's requirement. Wide range of Applications
More informationType Nominal voltage (V) Code HSV V
Speed control Speed control relay - mm Control of overspeed, underspeed, operating rate, stopping Measurement via discrete sensors - -wire PNP or NPN, Namur, voltage 0-0V or volt-free contact type Works
More informationProtection components
Multifunction protection relays LT-P Environment Conforming to standards IEC 947-4-1, IEC 34-11, IEC 755, VDE 010, VDE 00. &Ãmarking Meets the essential requirements of the Low Voltage equipment (LV) &
More informationem4 em4 alert em4 alert 2G
em4 em4 alert em4 alert 2G Connect your equipment to the GPRS 2G network and get alerted by SMS or email Control your application by SMS Receive data reports by SMS or datalogs by email or FTP in.csv (Excel)
More information02/11/2015
Modem communication plug and play solutions GSM Part number 88970119 For remote control of your application Automatic notification of alarms via SMS (GSM Modem) / email or on a PC with M3 ALARM software.
More information02/11/2015
Modem communication plug and play solutions GSM Part number 88970119 For remote control of your application Automatic notification of alarms via SMS (GSM Modem) / email or on a PC with M3 ALARM software.
More informationRE17RAMU on-delay timing relay - 1 s..100 h V AC - 1 OC
Characteristics on-delay timing relay - 1 s..100 h - 24..240 V AC - 1 OC Product availability : Stock - Normally stocked in distribution facility Price* : 42.90 USD Main Range of product Product or component
More informationNo mark Time-limit SPDT (1c) A Time-limit DPDT (2c) B Time-limit SPDT (1c), Instantaneous SPDT (1c) S DIN W48 H48mm.
Series Digital LCD Timer DIN W48 H48mm Features Power supply : 4-4VAC 5/6Hz, 4-4VDC universal Easy to switch Up/Down mode programmable output modes and timing ranges () Selectable function by front digital
More informationRE17RMMU time delay relay 10 functions - 1 s..100 h V AC - 1 OC
Characteristics time delay relay 10 functions - 1 s..100 h - 24..240 V AC - 1 OC Product availability : Stock - Normally stocked in distribution facility Price* : 62.00 USD Main Range of product Product
More information02/11/2015
DIN Rail Mount 17.5 mm MXR1 Part number 88826185 Just one digit differentiates the new range part number from the old range's Previous part number : 88 826 XXX / new part number : 88 827 XXX Part numbers
More informationRE7RL13BU off-delay timing relay with control contact s - 24 V AC DC - 2OC
Characteristics off-delay timing relay with control contact - 0.05..1 s - 24 V AC DC - 2OC Product availability : Stock - Normally stocked in distribution facility Price* : 189.00 USD Main Range of product
More information02/11/2015
"Compact" range with display CD12 Part number 88970041 Green LCD with 4 lines of 18 characters and configurable backlighting More cost effective solution Industrial temperature range (-20 C +55 C) Analogue
More informationModel Number Structure
Total Counter/Time Counter (DIN 72 x 36) CSM DS_E_4_1 DIN 72 x 36-mm Total Counter/Time Counter with Easy-to-read Displays and Water and Oil Resistance Equivalent to IP66 Large, easy-to-read displays:
More informationPulse Scaler for DIN Rail Attachment
Type 651 Pulse Scaler for DIN Rail Attachment Programmable pulse scaling factor up to 2047:1 NAMUR generator input PNP transistor output Max. pulse frequency 5 khz PROGRAMMING The divisor is set in binary
More information02/11/2015
Smart "Compact" range with display CD20 Smart Part number 88974053 Highly visible blue LCD with 4 lines of 18 characters and configurable backlighting Allow the use of the entire library of specific functions
More information08/07/2015
17.5 mm - 1 Relay 8A MUR1 Part number 88827105 Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator (relay version) Possibility of external load connection
More informationRE11RMMU time delay relay 10 functions - 1 s..100 h V AC - 1 OC
Product data sheet Characteristics RE11RMMU time delay relay 10 functions - 1 s..100 h - 24..240 V AC - 1 OC Complementary Contacts material Width pitch dimension Control type Voltage range Connections
More informationSolid-State Digital Counter H7AN
Solid-State Digital Counter Preset and Totalizing Counters with Up to 8-Digit LED Displays Draw-out construction allows setting, servicing without disconnecting wiring Choose from selectable UP/DOWN or
More informationRE7MY13MW time delay relay 8 functions s V AC DC - 2OC
Characteristics time delay relay 8 functions - 0.05..1 s - 240 V AC DC - 2OC Main Range of product Product or component type Contacts type and composition Component name Time delay type Time delay range
More informationNPN PNP NPN PNP NPN PNP
Cam Positioner Low-Cost, High-Performance Electronic Cam Switch for Use with OMRON E6F Rotary Encoder Control outputs can be programmed to turn ON/OFF in 1 units of rotary encoder shaft rotation Handles
More information02/11/2015
Smart range with Removable Terminal blocks XD26RBT Smart Part number 88974561 Designed for industrial, commercial, medical and paramedical machines Faster maintenance process which improves the machine
More informationPosition Indicator with/without Limit Values
.1 Position Indicator with/without Limit Values Large, 6-digit, 14 mm high LED display Prescaler 2 variable limit values Eeasy direct selection by 2 function keys Rrelay output with two change-over contacts
More informationModel Number Structure
Total Counter/Time Counter (DIN 72 x 36) CSM DS_E_5_3 DIN 72 x 36-mm Total Counter/Time Counter with Easy-to-read Displays and Water and Oil Resistance Equivalent to IP66 Large, easy-to-read displays:
More informationContents H3CR. DIN 48 x 48-mm Multifunctional Timer Series. Broad Line-up of H3CR Series H3CR-A. Solid-state Timer. Common to ALL Timers
Solid-state Timer H3CR DIN 48 x 48-mm Multifunctional Timer Series Conforms to EN61812-1 and EN60664-1 (VDE0110) 4 kv/2 for Low Voltage, and EMC Directives. Approved by UL and CSA. Lloyds/NK approvals.
More informationType: EASY719 DA RC Article No.: Ordering information Relay outputs Quantity 6 Power supply V DC 12 V DC. Description
Type: EASY719 DA RC Article.: 274117 Ordering information Relay outputs Quantity 6 Power supply V DC 12 V DC Description 12 digital inputs (4 inputs available as analog inputs) 6 relay outputs LCD display
More information08/07/2015
17.5 mm - 1 Solid State Relay 0.7A MUS2 Part number 88827004 Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator (relay version) Possibility of external
More informationDevice manual Multifunction display and evaluation system FX 360. Mode/Enter
Device manual Multifunction display and evaluation system FX 360 7390275 / 08 07 / 2009 Mode/Enter Set Safety instructions This manual is part of the unit. It contains texts and diagrams for the correct
More information02/11/2015
DIN Rail Mount 17.5 mm MURc3 Part number 88826503 DIN Rail Mount 17.5 mm MURc3 Part number 88826503 Just one digit differentiates the new range part number from the old range's Previous part number : 88
More informationSolid-state Timer H3DS
Solid-state Timer H3DS DIN Track Mounted, Standard 17.5-mm Width Timer Range A wide AC/DC power supply range (24 to 230 VAC/ 24 to 48 VDC) reduces the number of timer models kept in stock. (24 to 230 VAC/VDC
More informationSolid-state Timer H3CR. DIN 48 x 48-mm Multifunctional Timer Series. Broad Line-up of H3CR Series H3CR-A
Solid-state Timer H3CR DIN 48 x 48-mm Multifunctional Timer Series Conforms to EN61812-1 and EN60664-1 (VDE0110) 4 kv/2. Conforms to EMC standards (EN50081-2 and EN50082-2). Approved by UL and CSA. Lloyds/NK
More information11/03/2013
17.5 mm DIN rail mounting MUR1 Part number 88826105 TO BE SOON REPLACED BY THE NEW CHRONOS 2 RANGE (ref. 88827...) Relay or solid state output Multi-function or mono-function Multi-range Multi-voltage
More informationATSU01N232LT soft starter for asynchronous motor - ATSU01-32 A V KW
Characteristics soft starter for asynchronous motor - ATSU01-32 A - 200..480V - 7.5..15 KW Main Range of product Product or component type Product destination Product specific application Device short
More informationATSU01N222LT soft starter for asynchronous motor - ATSU01-22 A V KW
Characteristics soft starter for asynchronous motor - ATSU01-22 A - 200..480 V - 4..11 KW Price* : 195.00 GBP Main Range of product Product or component type Product destination Product specific application
More informationType: EASY719 AC RC Article No.: Ordering information Relay outputs Quantity 6 Power supply V DC 115/230 V AC. Description
Type: EASY719 AC RC Article No.: 274115 Ordering information Relay outputs Quantity 6 Power supply V DC 115/230 V AC Description 12 digital inputs 6 relay outputs LCD display Operating buttons Screw terminals
More information24/07/2012
17.5 mm DIN rail mounting MURc3 Part number 88826503 Relay or solid state output Multi-function or mono-function Multi-range Multi-voltage Screw or spring terminals LED status indicator (relay version)
More informationOvercurrent Protection / 7SJ45
Overcurrent Protection / SJ SIPROTEC easy SJ numerical overcurrent protection relay powered by CTs Fig. / Description SIPROTEC easy SJ numerical overcurrent protection relay powered by current transformers
More informationTechnical data. Functional safety related parameters MTTF d. Transfer characteristics. Time delay before availability. Standard conformity
KFU8-DW-.D Release date: 2-2- 2:8 Date of issue: 26-8- 4_eng.xml Model Number KFU8-DW-.D Rotation Speed Monitor Features Speed monitoring up to 4 khz pre-select value with relay output and LED indicator
More informationTeSys contactors. TeSys D contactors. IEC/EN , IEC/EN , UL 508, CSA C22.2 n 14. Protection against direct fi nger contact IP 2X
Characteristics Contactor type LC1 D09 D18 DT20 and DT25 Environment Rated insulation voltage (Ui) Conforming to IEC 097--1, overvoltage category III, degree of pollution: 3 Conforming to UL, CSA V 00
More informationComponents for safety applications Preventa safety modules
Selection guide Applications Modules For Emergency Stop and limit switch monitoring (modules integrated in Micro PLCs) Conforming to standards Machine IEC 204-, EN 292, EN 48 assemblies EN 60204- Principles
More informationReferences 1 for asynchronous motors 1
References 1 DF56902 DF5690 DF56901 ATS 01N10FT ATS 01N212QN ATS 01N20LY for 0.7 to kw motors power Nominal current Reference (2) Weight Single phase -phase 20 V 210 V 20 V 20 V 400 V 460 V kw HP kw HP
More informationRE48AML12MW time delay relay 2 functions s..300 h V AC - 2 OC
Characteristics time delay relay 2 functions - 0.02 s..300 h - 24..240 V AC - 2 OC Product availability : Stock - Normally stocked in distribution facility Price* : 86.00 USD Main Range of product Product
More information05/09/2012
17.5 mm EMER8 Part number 88829198 Multifunction or mono-function Multi-range (7 ranges) Multi-voltage or single voltage Screw terminals LED status indicator (1 voltage present LED, 1 timer ON LED) Option
More informationSelf-powered Counter
Self-powered Counter Subminiature Totalizing Counter Requires No External Power Supply DIN-sized 48 24 mm Wire-wrap terminal and screw terminal types available. AC/DC voltage, DC voltage, and No-voltage
More informationProtection components
General Application LT3-Si thermistor protection units continuously monitor the temperature of the machines to be protected (motors, generators, etc.) by means of PTC thermistor probes embedded in the
More informationDRTS 66 The new generation of advanced test equipments for Relays, Energy meters, Transducers and Power quality meters
The new generation of advanced test equipments for Relays, Energy meters, Transducers and Power quality meters Testing all relay technologies: electromechanical, solid state, numerical and IEC61850 Manual
More informationRENF22R2MMW Zelio Timer Relay - Modular
Characteristics Zelio Timer Relay - Modular Main Range of product Product or component type Device short name Operating system Software version Software designation Complementary Discrete output type Nominal
More informationRI-F200 Series. Single and Three Phase Multifunction Energy Meter. Telephone : +44 (0) Displayed Parameters
RI-F200 Series Single and Three Phase Multifunction Energy Meter DIN 96 panel mounted -/1A or -/5A current transformer input Single phase or three phase network compatible Programmable voltage and current
More informationFlexible Counter Series in DIN size 24 x 48 mm
Flexible Counter Series in DIN size 24 x 48 mm high contrast 8-digit LCD display or brilliant 6-digit LED display different supply voltages available: independent of mains supply with lithium battery or
More informationCharacteristics 5 TeSys k contactors and reversing contactors
90 Characteristics contactors k contactors and reversing contactors Environment characteristics Conforming to standards IEC 60947, NF C 63-110, VDE 0660, BS 424 Product certifications LCp and LPp K06 to
More informationNPRG860 & NPRG870 perform synchronization and paralleling of generators with electrical network. NPRG860 features a speed adjustment function.
REGULATION AUTOMATIC SYNCHRONIZER for GENERATOR NPRG860 & NPRG870 perform synchronization and paralleling of generators with electrical network. NPRG860 features a speed adjustment function. NPRG870 adds
More informationNPRG860 NPRG870 REGULATION. Automatic Synchronizer for Generator
REGULATION Automatic Synchronizer for Generator NPRG860 & NPRG870 perform synchronization and paralleling of generators with electrical network. NPRG860 features a speed adjustment function. NPRG870 adds
More informationPD30CNB25xxPS. Photoelectrics, Background suppression reflective - PointSpot. Main features. Main functions. Description
Photoelectrics, Background suppression reflective - PointSpot Main features Miniature sensor range The visible red PointSpot light makes alignment very easy Range: 250 mm Sensitivity adjustment by potentiometer
More information05/09/2014
48 x 48 Digital LCD Timer 814 Part number 88857005 Relay output digital timers LCD or LED (815E) Multi-range Multi-voltage 1 or 2 relay outputs Reset function on panel (Timers 815, 815E) Data saved in
More informationRI-D440. Three Phase easywire Multifunction DIN Rail Energy Meter. Telephone : +44 (0) Displayed Parameters
RI-D440 Three Phase easywire Multifunction DIN Rail Energy Meter Four module DIN rail mounted Energy pulse LED 330mV Input from easywire CTs (or -/1A and -/5A current transformer input with TAS-SCTEWA
More informationDigital Counter. DIN 72 x 72 mm Counters with Easy-to-use Functions
Digital Counter DIN 7 x 7 mm Counters with Easy-to-use Functions Designed with an emphasis on ease of operation. All models equipped with prescale function which displays in units of actual physical parameters
More informationGEMINI 1000/ DIGIT PRESETTABLE COUNTERS OR RATE INDICATORS GEMINI SINGLE LEVEL & GEMINI DUAL LEVEL w/optional 20 ma CURRENT LOOP
Bulletin No. GEM1/2-E Drawing No. LP0319 Released 1/05 GEMINI 1000/2000-6-DIGIT PRESETTABLE COUNTERS OR RATE INDICATORS GEMINI 1000 - SINGLE LEVEL & GEMINI 2000 - DUAL LEVEL w/optional 20 ma CURRENT LOOP!
More informationRE7TP13BU adjustable on-delay timing relay s - 24 V AC DC - 2OC
Characteristics adjustable on-delay timing relay - 0.05..1 s - 24 V AC DC - 2OC Price* : 189.00 USD Discontinued Main Range of product Product or component type Contacts type and composition Component
More informationGeneral Specifications
General Specifications GS 05F01D01E MODEL UM351 Digital Indicator with Alarms with Active Color PV Display General Model UM351 Digital Indicator with Alarms is a precision alarm instrument provided with
More information38 Series - Relay interface modules A
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 A Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit EMR Electromechanical Relays
More informationPhase control Single function phase control relay - 7.5 mm Control of -phase networks: phase sequence, total phase failure Multi-voltage from x 08 to x 480 V Controls its own supply voltage True RMS measurement
More informationModel Number Structure. Ordering Information. Solid-state Power OFF-delay Timer H3DE-H. Model Number Legend. List of Models
Solid-state Power OFF-delay Timer H3DE-H Timers Two delay-time models available. 0.1 to 12 seconds (S Series) 1 to 120 seconds (L Series) Covers wide range of supply voltage. Model Number Structure Model
More information38 Series - Relay interface modules A
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 A Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit 6.2 mm wide EMR - DC, AC or AC/DC
More information02/11/2015
17.5 mm - 1 Relay 5A EMER8 Part number 88829198 Multifunction or mono-function Multi-range (7 ranges) Multi-voltage or single voltage Screw terminals LED status indicator (1 voltage present LED, 1 timer
More informationRE7CP13BU adjustable symmetrical flashing relay s - 24 V AC DC - 2OC
Characteristics adjustable symmetrical flashing relay - 0.05..1 s - 24 V AC DC - 2OC Price* : 202.00 USD Discontinued Main Range of product Product or component type Contacts type and composition Component
More informationProximity Sensor Terminology
The following descriptions refer to the European standard EN 60947-5-2. of 2007. The specifications given here are intended to be minimum performance values described by the standard. Alignment must not
More informationTZIF 4. Current-to-Pulse Converter 10/ EN
TZIF 4 Current-to-Pulse Converter Conversion of direct current or voltage signals into a proportional pulse frequency Integration and average value formation of analog signals for quantity counting/remote
More informationATS01N206QN soft starter for asynchronous motor - ATS01-6 A V KW
Characteristics soft starter for asynchronous motor - ATS01-6 A - 380..415V - 1.5..3 KW Main Range of product Altistart 01 Product or component type Product destination Product specific application Device
More informationPRELIMINARY DATA SHEET RI-D140. Three Phase Multifunction DIN Rail Energy Meter (MID Certified) MID
RI-D140 Three Phase Multifunction DIN Rail Energy Meter (MID Certified) Four module DIN rail mounted Energy pulse LED True RMS measurement Cost effective and accurate Modbus communication -/1A or -/5A
More information12/2 Product overview. 12/3 7KT1 14, 7KT1 53 E-counters. 12/9 7KT1 11, 7KT1 12 digital measuring devices. 12/11 7KT1 0 analog measuring devices
BETA Measuring /2 Product overview /3 7KT1 14, 7KT1 53 E-counters /9 7KT1 11, 7KT1 digital measuring devices /11 7KT1 0 analog measuring devices / 7KT5 8 time and pulse counters /14 7KT5 5, 7KT5 6 time
More informationSIPROTEC easy 7SJ46 Numerical Overcurrent Protection Relay
Overcurrent Protection / 7SJ46 SIPROTEC easy 7SJ46 Numerical Overcurrent Protection Relay Function overview Fig. /11 Description The SIPROTEC easy 7SJ46 is a numerical overcurrent protection relay which
More informationEnergy Management Three-phase energy meter with output modules Type EM4-DIN
Energy Management Three-phase energy meter with output modules Type EM4-DIN Class 1 (active energy) Class 2 (reactive energy) Three-phase multi-function energy meter Back-lighted LCD display 3 1 / 2 DGT
More informationAnalogue temperature controllers
Analogue temperature controllers CT8A Input by J-K thermo-couple or by thermo-resistance Pt 00 (-wire) regulation modes : ON/OFF or proportional derivative selected by wiring Relay output Specifications
More informationBulletin 700-HX Multifunction Digital Timing Relay
Bulletin 700-HX Multifunction Digital Timing Relay Model Operating Mode Timing Range Socket Type Contact Output No. of Pins Input Voltage Cat. No. Cat. No. 700 HX A mode: Signal ON-Delay 1 A-1 mode: Signal
More informationElectronic timer CT-TGD.22
2CDC 251 097 F0t06 a Rotary switch for the preselection of the time range of the ON time b Potentiometer with direct reading scale for the fine adjustment of the ON time c Rotary switch for the preselection
More informationGEMINI PRESETTABLE DUAL RATE INDICATOR WITH RATIO (A/B)
Bulletin No. GEM5-C Drawing No. LP0321 Released 1/05 GEMINI 5200 - PRESETTABLE DUAL RATE INDICATOR WITH RATIO (A/B)! DIFFERENCE (A-B), OR DRAW [(A-B)/B] INDICATION! 6-DIGIT, 0.56" (14.2 mm) HIGH LED DISPLAY
More informationTechnical Data Sheet. x1000. kwh R Y B
Technical Data Sheet x1000 Von kwh IRev 3600 imp /kwh R Y B is a compact multifunction instrument which is a 96mm x 96mm panel mounted kilowatt hour meter it measures active energy with class 1.0 accuracy
More informationRISH EM 3490 SS Kilowatt Hour Energy Meter With Rs485 RISH EM 3490 SS. Application : Product Features: Indication: Pulse Indication:
Application : RISH Master 3490 SS is a 96mm x 96mm panel mounted kilowatt hour meter it measures active energy with class 1.0 accuracy having auto-resetting 8 digit seven segment LED counter. The unit
More informationSolid-state Timer H3DE
Solid-state Timer H3DE DIN-rail Mounted, Standard 22.5-mm Width Timer Range A wide AC/DC power supply range (24 to 230 VAC/DC) reduces the number of timer models kept in stock. (except for H3DE-H) 12-VDC
More informationControl stations and enclosures Pendant control stations, for control circuits Double insulated or metal, types XAC-B and XAC-M
Characteristics Pendant control stations, for control circuits Environment Conforming to standards IEC 947-5-1, EN 60947-5-1 XAC-B : standard version : NEMKO, CSA 300 V type 4 Approvals XAC-M : standard
More informationWHEN A PLC IS TOO MUCH, AND SPACE FOR
WHEN A PLC IS TOO MUCH, AND SPACE FOR A RELAY SEQUENCE CIRCUIT IS TOO LITTLE Pattern Selector 59 2.33 66 2.6 70 2.75 No programming required Select from among 15 preset patterns Wiring far simpler than
More information