FEASIBILITY OF OPTICAL CLOCK DISTRIBUTION FOR FUTURE CMOS TECHNOLOGY NODES

Similar documents
Lecture #2 Solving the Interconnect Problems in VLSI

Novel Buffer Design for Low Power and Less Delay in 45nm and 90nm Technology

Design & Analysis of Low Power Full Adder

Low-Power VLSI. Seong-Ook Jung VLSI SYSTEM LAB, YONSEI University School of Electrical & Electronic Engineering

Design of Low-Power High-Performance 2-4 and 4-16 Mixed-Logic Line Decoders

A new 6-T multiplexer based full-adder for low power and leakage current optimization

12-nm Novel Topologies of LPHP: Low-Power High- Performance 2 4 and 4 16 Mixed-Logic Line Decoders

Low Power Design of Successive Approximation Registers

BICMOS Technology and Fabrication

Trends and Challenges in VLSI Technology Scaling Towards 100nm

Variable-Segment & Variable-Driver Parallel Regeneration Techniques for RLC VLSI Interconnects

NOVEL OSCILLATORS IN SUBTHRESHOLD REGIME

Low Power High Performance 10T Full Adder for Low Voltage CMOS Technology Using Dual Threshold Voltage

Low Power Design for Systems on a Chip. Tutorial Outline

Investigation on Performance of high speed CMOS Full adder Circuits

DESIGN OF A NOVEL CURRENT MIRROR BASED DIFFERENTIAL AMPLIFIER DESIGN WITH LATCH NETWORK. Thota Keerthi* 1, Ch. Anil Kumar 2

A MONOLITHICALLY INTEGRATED PHOTORECEIVER WITH AVALANCHE PHOTODIODE IN CMOS TECHNOLOGY

Modeling the Effect of Wire Resistance in Deep Submicron Coupled Interconnects for Accurate Crosstalk Based Net Sorting

EE 42/100 Lecture 23: CMOS Transistors and Logic Gates. Rev A 4/15/2012 (10:39 AM) Prof. Ali M. Niknejad

DIGITAL INTEGRATED CIRCUITS A DESIGN PERSPECTIVE 2 N D E D I T I O N

DESIGN OF LOW POWER HIGH PERFORMANCE 4-16 MIXED LOGIC LINE DECODER P.Ramakrishna 1, T Shivashankar 2, S Sai Vaishnavi 3, V Gowthami 4 1

A Review of Clock Gating Techniques in Low Power Applications

RECENT technology trends have lead to an increase in

UNIT-II LOW POWER VLSI DESIGN APPROACHES

Design of High Performance Arithmetic and Logic Circuits in DSM Technology

INTERNATIONAL JOURNAL OF APPLIED ENGINEERING RESEARCH, DINDIGUL Volume 1, No 3, 2010

ECEN689: Special Topics in High-Speed Links Circuits and Systems Spring 2012

Implementation of dual stack technique for reducing leakage and dynamic power

EEC 216 Lecture #10: Ultra Low Voltage and Subthreshold Circuit Design. Rajeevan Amirtharajah University of California, Davis

Variation-Aware Design for Nanometer Generation LSI

On Chip Active Decoupling Capacitors for Supply Noise Reduction for Power Gating and Dynamic Dual Vdd Circuits in Digital VLSI

STATIC cmos circuits are used for the vast majority of logic

Design of Low Power High Speed Fully Dynamic CMOS Latched Comparator

A Survey of the Low Power Design Techniques at the Circuit Level

LOW POWER VLSI TECHNIQUES FOR PORTABLE DEVICES Sandeep Singh 1, Neeraj Gupta 2, Rashmi Gupta 2

White Paper Stratix III Programmable Power

Preface to Third Edition Deep Submicron Digital IC Design p. 1 Introduction p. 1 Brief History of IC Industry p. 3 Review of Digital Logic Gate

Performance Comparison of CMOS and Finfet Based Circuits At 45nm Technology Using SPICE

Short-Circuit Power Reduction by Using High-Threshold Transistors

An Optimal Design of Ring Oscillator and Differential LC using 45 nm CMOS Technology

Low-Power Digital CMOS Design: A Survey

ISSCC 2003 / SESSION 10 / HIGH SPEED BUILDING BLOCKS / PAPER 10.8

UNIT-III POWER ESTIMATION AND ANALYSIS

DESIGNING OF SRAM USING LECTOR TECHNIQUE TO REDUCE LEAKAGE POWER

Ultra Low Power VLSI Design: A Review

DESIGN AND ANALYSIS OF LOW POWER CHARGE PUMP CIRCUIT FOR PHASE-LOCKED LOOP

EE 330 Lecture 43. Digital Circuits. Other Logic Styles Dynamic Logic Circuits

LSI and Circuit Technologies for the SX-8 Supercomputer

SCALING power supply has become popular in lowpower

DFT for Testing High-Performance Pipelined Circuits with Slow-Speed Testers

AS very large-scale integration (VLSI) circuits continue to

A Novel Low Power Optimization for On-Chip Interconnection

Introduction. Digital Integrated Circuits A Design Perspective. Jan M. Rabaey Anantha Chandrakasan Borivoje Nikolic. July 30, 2002

IN the design of the fine comparator for a CMOS two-step flash A/D converter, the main design issues are offset cancelation

Chapter 4. Problems. 1 Chapter 4 Problem Set

An Overview of Static Power Dissipation

PROCESS and environment parameter variations in scaled

Pramoda N V Department of Electronics and Communication Engineering, MCE Hassan Karnataka India

Double Stage Domino Technique: Low- Power High-Speed Noise-tolerant Domino Circuit for Wide Fan-In Gates

DESIGN & IMPLEMENTATION OF SELF TIME DUMMY REPLICA TECHNIQUE IN 128X128 LOW VOLTAGE SRAM

EECS 141: SPRING 98 FINAL

A High-Speed Variation-Tolerant Interconnect Technique for Sub-Threshold Circuits Using Capacitive Boosting

High-speed Serial Interface

Semiconductor Memory: DRAM and SRAM. Department of Electrical and Computer Engineering, National University of Singapore

An Efficient Design of CMOS based Differential LC and VCO for ISM and WI-FI Band of Applications

Power-Area trade-off for Different CMOS Design Technologies

Static Power and the Importance of Realistic Junction Temperature Analysis

EE 330 Lecture 43. Digital Circuits. Other Logic Styles Dynamic Logic Circuits

ADIABATIC LOGIC FOR LOW POWER DIGITAL DESIGN

Performance Analysis of Novel Domino XNOR Gate in Sub 45nm CMOS Technology

A Novel Flipflop Topology for High Speed and Area Efficient Logic Structure Design

A NEW APPROACH FOR DELAY AND LEAKAGE POWER REDUCTION IN CMOS VLSI CIRCUITS

WITH the rapid proliferation of numerous multimedia

Separation and Extraction of Short-Circuit Power Consumption in Digital CMOS VLSI Circuits

The GBTIA, a 5 Gbit/s Radiation-Hard Optical Receiver for the SLHC Upgrades

Design of Low Power Vlsi Circuits Using Cascode Logic Style

A Novel Approach for High Speed and Low Power 4-Bit Multiplier

DESIGN OF EXTENDED 4-BIT FULL ADDER CIRCUIT USING HYBRID-CMOS LOGIC

A Novel Continuous-Time Common-Mode Feedback for Low-Voltage Switched-OPAMP

RELIABILITY ANALYSIS OF DYNAMIC LOGIC CIRCUITS UNDER TRANSISTOR AGING EFFECTS IN NANOTECHNOLOGY

4 principal of JNTU college of Eng., JNTUH, Kukatpally, Hyderabad, A.P, INDIA

LSI ON GLASS SUBSTRATES

Lecture 04 CSE 40547/60547 Computing at the Nanoscale Interconnect

LOW POWER HIGH PERFORMANCE DECODER USING SWITCH LOGIC S. HAMEEDA NOOR 1, T.VIJAYA NIRMALA 2, M.V.SUBBAIAH 3 S.SALEEM 4

DesignCon Design of a Low-Power Differential Repeater Using Low Voltage and Charge Recycling. Brock J. LaMeres, University of Colorado

A Novel Radiation Tolerant SRAM Design Based on Synergetic Functional Component Separation for Nanoscale CMOS.

Topic 6. CMOS Static & Dynamic Logic Gates. Static CMOS Circuit. NMOS Transistors in Series/Parallel Connection

Design of a Low Voltage low Power Double tail comparator in 180nm cmos Technology

Lecture 16. Complementary metal oxide semiconductor (CMOS) CMOS 1-1

A Low-Power High-speed Pipelined Accumulator Design Using CMOS Logic for DSP Applications

Energy Reduction of Ultra-Low Voltage VLSI Circuits by Digit-Serial Architectures

An energy efficient full adder cell for low voltage

IMPLEMANTATION OF D FLIP FLOP BASED ON DIFFERENT XOR /XNOR GATE DESIGNS

Design of a Low Power 5GHz CMOS Radio Frequency Low Noise Amplifier Rakshith Venkatesh

Design and Implementation of Current-Mode Multiplier/Divider Circuits in Analog Processing

Leakage Current Modeling in PD SOI Circuits

Practical Information

IJMIE Volume 2, Issue 3 ISSN:

Low Power Design in VLSI

Temperature-adaptive voltage tuning for enhanced energy efficiency in ultra-low-voltage circuits

Transcription:

6 Vol.11(1) March 1 FEASIBILITY OF OPTICAL CLOCK DISTRIBUTION FOR FUTURE CMOS TECHNOLOGY NODES P.J. Venter 1 and M. du Plessis 1 and Carl and Emily Fuchs Institute for Microelectronics, Dept. of Electrical, Electronic & Computer Engineering, Corner of University Road and Lynnwood Road, University of Pretoria, Pretoria, South Africa 1 E-mail: jannes.venter@up.ac.za E-mail: monuko@up.ac.za Abstract: CMOS is arguably the most successful semiconductor technology in electronics history. This is clear by the constant efforts involved in scaling as the key driver of improving the performance of ICs to keep up with consumer expectations. However, this trend has lately been haltered by another on-chip component: the interconnect. As scaling decreases active device dimensions for a corresponding performance increase, interconnect dimensions suffer under reduction due to increasing capacitance and resistance. One possible solution might be to move the long, power consuming global signal nets into the optical domain. This paper compares predicted electrical versus optical global signal distribution for future nanometre CMOS nodes, based on clock distribution and the associated power consumption. Keywords: Optical interconnect, CMOS, optical clock distribution, hybrid. 1. INTRODUCTION CMOS still has an immense impact as the dominant semiconductor technology for mass integration. Given the monetary and development investment up to date, the industry is throwing its full weight behind the continuation of scaling, both in terms of function density and in performance. With various breakthroughs on device level, the limitations on future scaling lie in the development of adequate interconnects to support the increase in logic density. There are numerous factors influencing the interconnect architecture used. None more so than the global clock distribution scheme. In modern microprocessor units (MPUs), the clock distribution network can be the single most power consuming entity. This work aims to take the International Technology Roadmap for Semiconductors (ITRS) [1] requirements for future technology nodes, along with predictive SPICE modelling, in order to extrapolate on what can be expected from future electrical clock networks. As a comparative platform, an electrical H-tree is characterised in terms of its electrical power consumption components. The results are then used to indicate the feasibility of optical clock networks as device dimensions decrease.. PREDICTIVE TECHNOLOGY MODEL In order to produce sensible circuit performance results, predictive SPICE modelling is used. Based on models developed by [] and updated with the latest ITRS [1] predicted requirements for devices, SPICE based models are employed for the simulation of the optical front end receiver and clock buffer circuits. This method ensures that aspects such as short circuit currents on switching events and device drain capacitances, which may influence the results substantially, are incorporated into the prediction. 3. COMPARATIVE ARCHITECTURE 3.1 An overview of future technology parameters 7 6 5 3 1 65 4.7 5.9 3 7.3 9. Clock [GHz] 11.5 7 1 13 16 19 Figure 1: CMOS scaling and local clock frequency timeline. 16 15 14.3 1 5 11 The ITRS publishes data on an annual basis wherein technology requirements are stipulated, based on past technology trends and future market interests. Combining this information with physical modelling of, for instance, the interconnects and CMOS active devices, key technology parameters affecting the performance of clock networks can be derived. Figure 1 shows the predicted trend for CMOS scaling within the next decade, along with the expected local clock frequencies. Table II summarises the most important characteristics that can be derived from process predictions, to be expected in the near future. Logic area is predicted to maintain a relatively constant portion of chip area, as opposed to the great reduction of logic portion in [3], since both logic and SRAM functions are expected to increase at the same rate [1]. Intel s nm Penryn [3] reinforces this trend Clock [GHz]

Vol.11(1) March 1 7 Table I: Overall technology characteristics. Parameters Units 65nm nm 3nm nm 16nm 11nm System characteristics V DD [V] 1.1 1.1 1.9.9.8 f clk [GHz] 4.7 5.9 7.3 9. 11.5 14.3 Logic area [cm ].86.87.87.88.88.88 D xtor [M/cm ] 357 714 147 854 578 11416 Device characteristics I on [μa/μm] 16 137 1948 1943 344 533 L physical [nm] 3 4 18 14 1.7 8.1 T oxp [nm] 1..95.7.7.6.55 T oxe [nm] 1.85 1.7 1.1 1.1 1.95 V th [mv] 5 175 13 15 19 19 Global interconnect characteristics r int [/μm].39.91 1.74 3.53 6. 1.67 c int [F/μm] E-16 1.8E-16 1.7E-16 1.5E-16 1.5E-16 1.3E-16 Local interconnect characteristics r int [/μm] 1..74 5.14 1.33 19.53 39.35 c int [F/μm] 1.8E-16 1.6E-16 1.5E-16 1.3E-16 1.3E-16 1.1E-16 n= 4 n= 3 n= 1 n= where the logic area portion remained roughly the same as the previous generation MPU, although the core size is smaller than predicted for high performance MPUs [1]. The current trend is roughly double the functions per area from one technology generation to the next. On a device level, where channel depths become small enough, it is important to include the quantisation effects as an electrical equivalent oxide thickness. The physical thickness represents the effective thickness for SiO, while newer high- solutions might utilise thicker gates to minimise gate tunnelling [4]. I on shows the strong inversion saturation current for NMOS devices at logic levels. The interconnect resistance and capacitance terms were calculated assuming full shielding, with minimum dimensions used for maximum density. Resistivity calculations consider effective resistance increases as dimensions decrease, including the grain boundary component, as well as the inclusion of the skin effect at high frequencies. 3. Clock tree topology The three most often used topologies include grids, trees and length matched serpentines [5]. Given the capacitive and skew advantages of tree structures, the symmetrical H-tree is used as a comparative topology for comparing electrical and optical power consumption performance. This topology applies to the distribution of the global clock signal, where handover occurs at the end points into local clock regions constructed with a local grid. This local region is fed by a local clock buffer and will be common to both electrical and optical networks. Each end point sees exactly the same path as any other from the source, making skew depend only on process and environmental variations. For the purpose of this work, a square die is assumed, sized according to the predicted logic portion of a typical modern MPU. Figure shows a die partitioning using an H-tree, with n representing the tree depth. Note that n for this work is not necessarily defined the same as compared to other works [3], [6]. For each increment of n, four new terminations, or end points will be instanced per (n - 1) level end point. A summary of characteristics in a typical H-tree network is shown in Table II. The depth of the tree, n, is determined by the maximum allowable skew for a local region, defined in [3]. As technology scales and the skew reaches a certain critical limit, the depth is incremented. The introduction of repeaters between tree splits along the segment becomes important to maintain signal flanks of an acceptable level. The % - 8 % transition time metric is used, where this should be maintained below 1% of the relevant technology node s clock period, T clk. The expressions developed in [7] can be modified to determine an expression for the interconnect length at which the transition time does not meet the stated criteria (see Section 4.1). 3.3 Tree depth and local region design The depth of the tree is determined by the maximum allowable skew within a local region; that is, after a global end point feeds the local clock grid. Given the known transistor density, it is assumed for the purpose of calculations that a there are 64 gates in a register and 5 transistors per gate. If the local region dimensions are known, it is possible to calculate the number of registers in a local region and consequently determine the longest Manhattan-type interconnect length from the local region Table II: H-tree length equations. n 3 Total H-tree length k L 4 k 1 3 n Figure : Partitioning of an H-tree. L Length contributed at level n ( 1) n Segment length at level n L 1 3 n Number of segments at level n L n Area of local region at level n l n Local area sidewall dimension die n Number terminating end points

8 Vol.11(1) March 1 buffer to the farthest register. This then represents the path of worst skew within a local region. If a maximum skew of 1 % of the clock period is used, it is possible to determine how deep the tree needs to be to adhere to the local skew requirements. Table III: Tree and repeater design for future nodes. Parameters 65nm nm 3nm nm 16nm 11nm Tree design Max local l seg 464. 96.4 1.9 138. 9.3 6. Tree depth n 6 6 7 7 8 9 # of end points 96 96 16384 16384 65536 6144 Max global l seg 41.73 6.93 193.6 16.3 84.17 56.3 # of repeaters 485 77 1953 8484 864 311798 # of split buffers 614 614 74 74 983 39314 Repeater design parameters A [ μm] 695.8 575.65 395.4 366.15 315.65 73.5 B [F/μm] 5.7E-15 4.8E-15.9E-15 3.E-15 3.E-15.9E-15 R.35.37.47.44.43.4 W [μm] 13.36 7.98 5.35 3.46. 1.51 4. CIRCUIT DESIGN 4.1 Electrical repeater circuits l a.55rintcint b 1.386r C c R c 1.386R C T seg int B int B B B 1% b b 4ac a Equation 1 shows the maximum allowable interconnect length before the % - 8 % time degrades beyond T CLK /1. The repeaters are sized to minimise l seg. A limit of two inverter pairs per repeater is set to maintain practicality. The input inverter pair is sized smaller compared to the output pair by a ratio R. This has the advantage of reducing the input capacitance, while maintaining a stronger driving capability. A lower limit exists on the value of R to maintain the requirement of a % - 8% transition time between inverter pairs. Equation quantifies the lower limit based on the timing constraints. (1) Solving Equation 3, with l seg as the maximum allowable segment length and c int as the interconnect capacitance per unit length, yields a solution for an optimal R value. The optimal width W represents a scaling factor for transistor width, where A and B represent width dependent input capacitance and output resistance parameters of the buffer determined through maximising the segment length in Equation 1, shown in Equation 4. W 4. Photodiode design c A int (4) rint RB One limiting factor in the design of an optical system is that the photodiode does not scale along with technology. This is partly due to the lower limit on the physical dimension of the pn-junction region to accommodate the wavelength of incident light. Another important factor is the light intensity per unit area, which becomes unrealistic if the photodiode active region is too small. Based on [8] it is possible to obtain multi-gigahertz operation with an n-well based photodiode with a responsivity of.3 A/W, with a device capacitance of 5 ff. 4.3 Optical receiver The chosen topology for the optical receiver front end is a high impedance design, similar to the approach in [3]. Figure 3 shows the configuration, where the photodiode discharges the input node in order to generate a logic transition by the first inverter. The following cascade of inverters serves both to delay the transition and to buffer the signal for subsequent stages. The signal v CH then recharges the input node after the cascade dependent delay. v CH i PD (t) in out v CH 1.386AB R 1.1 () T 1% T 1% is one tenth of a clock period and the factor of 1.1 is inserted as a safety margin to ensure that the inter-stage transition time is not limiting. Although Equation states a limit, an optimal value for R can be found if the total capacitance, that is the sum of the interconnect and repeater components, are normalised to a per unit length metric. Ctotal / length BW(1 R) cint R R l (3) seg Figure 3: High impedance switched optical front end. Although this requires a relatively strong optical pulse, the duration thereof may be very short. This topology is also well suited to standard cell compatibility, has a far superior noise performance when compared to transimpedance amplifier (TIA) approaches, and only consumes power on transitions. Most of the power consumed is due to the inverters required for driving a local region clock buffer.

Vol.11(1) March 1 9 5.1 SPICE simulations 5. POWER CONSUMPTION It is possible to, from a completely theoretical perspective, utilise the following equation to determine the dynamic power dissipation of the clock networks (Equation 5). P C f V (5) dyn clk DD The true power consumption will increase due to short circuit currents on a switching event, and buffer output capacitances, which are difficult to model by hand. Therefore, predictive models (see Section ) are used to estimate a more accurate quantity for expected power consumption of circuits and interconnects, which is used in the subsequent comparisons. This will obviously be more comprehensive than simply using Equation 5. 5. Electrical components Figure 4 shows the resulting power consumption based on the above methodology. Because the interconnect dimensions is kept at minimum, the power consumption of the supporting circuitry for maintaining signal fidelity, namely the repeaters, are responsible for a substantial contribution to the overall power consumption. Of course, increasing the interconnect dimensions results in the component power being replaced by an increased interconnect component. It is also clear that the deep tree in the 16 nm and 11 nm nodes are contributory to the sharp increase in global power consumed. 16 1 1 1 8 6 Interconnect Component Total 65 3 16 11 Figure 4: Electrical network power consumption. 5.3 Optical components Figure 5 shows the situation when a fully optical tree replaces the electrical tree in Section 5.. It becomes clear that the optical power required to maintain reasonable operation also suffers at the smaller nodes. One big reason for the sudden increase is the constant charging capacitance present on the input node in Figure 3, while the operating frequency increases. This is due to the large photodiode capacitance, which is assumed to remain constant throughout. The electrical component represents the power required to amplify the signal enough to drive a local region buffer, as well as recharging the input node capacitance back to a high logic state. 18 16 Electrical Optical 1 Total 1 1 8 6 65 3 16 11 Figure 5: Optical network power consumption. 5.4 Hybrid network performance From Figure 4 and Figure 5 it is clear that the 16 nm and 11 nm nodes presents a limit to where optical networks will outperform electrical networks. Figure 6 shows the total global clock network power consumed when the tree is made up of an optical tree up to level n, and then continues as an electrical tree for the rest of the tree levels. It is interesting to note that an optical tree stopping at level 7 is just as power hungry as a fully optical tree (stopping at level 8), while the required external power efficiency (EPE) to beat a completely electrical network is less stringent. Note that this EPE value does not include propagation, bending and coupling losses. 55 5 35 3 Total power Required EPE 1 3 4 5 6 7 8 Tree level [n] 9 8 7 6 5 3 1 Figure 6: Total power with optical tree up to different depths, 16 nm node. An even more interesting result is shown in Figure 7, where it can be seen that the total power consumption of the clock network decreases as the optical tree is introduced at deeper levels, but only up to a point. After a tree depth of 7 the overall power consumption increases drastically, where the required EPE to beat an electrical

3 Vol.11(1) March 1 system exceeds 1 %, showing that the optical network fails to surpass the performance of an electrical one. 16 155 15 1 1 135 13 Total power Required EPE 1 3 4 5 6 7 8 9 Tree level [n] 1 1 Figure 7: Total power with optical tree up to different depths, 11 nm node. 11 1 9 8 7 6 5 65 3 16 11 165 1 15 15 85 65 5 Optical EPE Hybrid EPE Figure 8: Optical vs. hybrid network EPE. 5 Electrical Optical Hybrid 65 3 16 11 Figure 9: Electrical, optical and hybrid network total power consumed. 8 6 shows that a hybrid network also relaxes the requirement for the source EPE, allowing more headroom for losses. Figure 9 shows the resulting power consumption comparisons for fully electrical, fully optical and hybrid networks for the 65 nm to 11 nm nodes. 6. CONCLUSION The future of interconnect technology, especially for global signals, might not necessarily find solutions in a completely pure move from electrical to optical, but rather in exploiting the advantages of both in the form of hybrid networks. It is also seen that there are some fundamental limits to scaling down the optics before it would really contend as a replacement for electrical networks. For now, if light sources and on chip interconnects can handle the requirements, it would seem that optical networks are already viable for replacing electrical networks at a global signal level. 7. REFERENCES [1] ITRS 8 Updated Report. [Online]. Available: http://www.itrs.net [] W. Zhao and Y. Cao, A new generation of predictive technology model for sub-nm design exploration, in Proc. of the 7 th International Symposium on Quality Electronic Design. 6, pp. 585-59. [3] B. Ackland, B. Razavi, and L. West. A comparison of electrical and optical networks in nanometer technologies, In Proc. of the IEEE 5 Custom Integrated Circuits Conference, pages 779-78. [4] G. Varghese et al. Penryn: -nm next generation Intel core processor, In Proc. of the Asian Solid-State Circuits Conference, 7, pages 14-17 [5] P. Restle and A Deutsch, Designing the best clock distribution network, in IEEE Symposium on VLSI Circuits, Honolulu, HI, USA, Jun 1998, pp. -5. [6] E. Friedman. Clock distribution networks in synchronous digital integrated circuits, Proceedings of the IEEE, 89(5):665-69, May 1. [7] T. Sakurai. Closed-form expressions for interconnection delay, coupling, and crosstalk in VLSIs, IEEE Trans. on Electron Devices, (1):118-14, Jan 1993. [8] S. Radovanovi, A.-J. Annema, and B. Nauta, Highspeed photodiodes in standard CMOS technology. Springer, 6. This shows that the optimal power consumption might be obtainable if a hybrid network is considered. Figure 8