HDMI Compliance Test Report Cable: WS356G40L2P5AC Active/Passive: Active Guage: 40AWG Length: 2.5M Connector Type: A-C Summary Pass/ Fail Comment Test 5-2 wire assignment Test 5-3 TMDS Data Eye Diagram Test 5-8 Differential Impedance Test 5-10 DDC/CEC Line Capacitance and Voltage Test 5-11 +5V Power Test 5-15 Utility Line Impedance HEACT 6-1: Intra-Pair Skew HEACT 6-2: Differential Attenuation HEACT 6-3: Differential/Common Mode Impedance See remaining worksheets for details of each test 1/1
5-2: Wire Assignment Cable_Type = not "Wire" CEC valid connection check (CDF) DDC (SDA, SCL) valid connection check (CDF) 5V valid connection check (CDF) HPD valid connection check (CDF) Reserved valid connection check (CDF) Ground valid connection check (CDF) /FAIL = 1/1
Product Number: HDMI SN: Port:1 HDMI Test Station 1 Unknown User 10/19/2010 12:40:0 ID 5-3 Cable Eye at 165 MHz D0 Test 5-3 Cable Data Eye for Cable Category 2 Jitter only on Clock Left Jitter (ps) 192.3 Right Jitter (ps) 190.9 Maximum Margin 48ps Data Jitter Amplitude [TBit] Data Jitter Mask Frequenc Violatio y [MHz] ns [] 0.245 0.5 0 pass pass Result 1/1
Product Number: HDMI SN: Port:1 HDMI Test Station 1 Unknown User 10/19/2010 12:40:0 ID 5-3 Cable Eye at 165 MHz D1 Test 5-3 Cable Data Eye for Cable Category 2 Jitter only on Clock Left Jitter (ps) 177.5 Right Jitter (ps) 177.5 Maximum Margin -53ps Data Jitter Amplitude [TBit] Data Jitter Mask Frequenc Violatio y [MHz] ns [] 0.245 0.5 0 pass pass Result 1/1
Product Number: HDMI SN: Port:1 HDMI Test Station 1 Unknown User 10/19/2010 12:40:0 ID 5-3 Cable Eye at 165 MHz D2 Test 5-3 Cable Data Eye for Cable Category 2 Jitter only on Clock Left Jitter (ps) 182.8 Right Jitter (ps) 181.5 Maximum Margin 57ps Data Jitter Amplitude [TBit] Data Jitter Mask Frequenc Violatio y [MHz] ns [] 0.245 0.5 0 pass pass Result 1/1
Product Number: HDMI SN: Port:1 HDMI Test Station 1 Unknown User 10/19/2010 12:40:0 ID 5-3 Cable Eye at 340 MHz D0 Test 5-3 Cable Data Eye for Cable Category 2 Jitter only on Clock Left Jitter (ps) 88.4 Right Jitter (ps) 88.4 Maximum Margin -24ps Data Jitter Amplitude [TBit] Data Jitter Mask Frequenc Violatio y [MHz] ns [] 0.205 0.5 0 pass pass Result 1/1
Product Number: HDMI SN: Port:1 HDMI Test Station 1 Unknown User 10/19/2010 12:40:0 ID 5-3 Cable Eye at 340 MHz D1 Test 5-3 Cable Data Eye for Cable Category 2 Jitter only on Clock Left Jitter (ps) 100.8 Right Jitter (ps) 100.8 Maximum Margin -16ps Data Jitter Amplitude [TBit] Data Jitter Mask Frequenc Violatio y [MHz] ns [] 0.205 0.5 0 pass pass Result 1/1
Product Number: HDMI SN: Port:1 HDMI Test Station 1 Unknown User 10/19/2010 12:40:0 ID 5-3 Cable Eye at 340 MHz D2 Test 5-3 Cable Data Eye for Cable Category 2 Jitter only on Clock Left Jitter (ps) 97.5 Right Jitter (ps) 97.5 Maximum Margin -21ps Data Jitter Amplitude [TBit] Data Jitter Mask Frequenc Violatio y [MHz] ns [] 0.205 0.5 0 pass pass Result 1/1
Test 5-8 Differential Impedance Tests Result: The following four plots shows the near end differential impedance plots for the clock line and the 3 data channels. The white line shows the filtered response, where a filter is applied to the TDR rising edge to achieve a rise time of 200ps The max and min measures are taken from the white curve. The blue line shows the unfiltered response Pass criteria : If an impedance measurment is <=75 Ohms or >= 125 Ohs then Fail If an impedance measurment is <= 85 Ohms or >= 115 Ohs for more than 250ps then Fail
CLK near end impedance Max 103 Min 89 Result
D0 near end impedance Max 98 Min 92 Result
D1 near end impedance Max 98 Min 87 Result
D2 near end impedance Max 99 Min 91 Result
Test 5-10 DDC/CEC Line Capacitance and Voltage Tests Result: Note the digital multimeter, ISO-TECH ICT76, was used to measure the capicitance on the SCL/SDA and CEC lines The HDMI test spec specifies to us a HIOKI 3522-50 Digital LCR Meter Spec: measured capacitance should be less than 700pF Wire SDA SCL CEC Capicitance 190 pf 184 pf 180 pf
Test 5-11 Active/Converter +5V Power Tests Result: During Test 50mA is drawn from the 5V line at Sink end of cable Bres chip will consume approx 5mA Total current from 5V line = 55mA Allowed voltage drop = 100mV Therefore max combined resistance of the 5V line and CEC_GND line = 100mV/55mA = 1.8 Ohms The following table presents the resistance of the various wires: Isource = 54 Supply 4.8V at source side connector & 50mA ma at sink side connector, fail if Isource > 55mA Vsink(HIGH) 4.71 V Fail if Vsink(HIGH) < 4.7V or Vsink(HIGH) >
Test 5-15 Utility Line Impedance Tests Result: Once activated through a CEC message, the Utility line aione(single Mode) or the Utility line in conjunction with the Hot Plug Detect line(common Mode) may be used for ARC transmmission as specified in Supplement2. lmpedance should be: 55 ohms ± 35 %
SINK SIDE MAX 69 ohm MIN 49 ohm Result
SOURCE SIDE MAX 62 ohm MIN 48 ohm Result
HEACT 6-1: Intra-Pair Skew Test result: Confirm that the intra-pair skew in the HDMI cable with HEAC is within the specified limit. Pass criteria : Maximum Cable Assembly Intra-Pair Skew 111ps at +/- 125mV Intra-Pair Skew Result 60 ps
HEACT 6-2: Differential Attenuation Test Result: Confirm that the lower limit of the differential attenuation of HDMI cable with HEAC is within specified limits: Pass criteria Differential Attenuation 300kHz-10MHz < 1.6dB 10MHz - 100MHz < 5dB 100MHz - 200MHz < 7.2dB 300kHz 1 10MHz 1.32 100MHz 4.15 Result
HEACT 6-3: Differential/Common Mode Impedance Test Result: Confirm the differential and common mode impedance of the HDMI cable with HEAC is within the specified limits. Pass criteria Differential Impedance Connection point and transition area: up to 1ns: 100ohm +/- 15% Cable area: 1ns - 2.5ns: 100ohm +/- 10% A single excursion is permitted out to a max/min of 100ohm +/- 25% and of a duration less than 250ps Differential Impedance Common Mode Impedance Cable area: 1ns - 2.5ns 30ohm +/-20%
MAX 102 ohm MIN 97 ohm Result Common mode Impedance MAX MIN Result 29 ohm 25 ohm