Features Regulated Converters Description :1 wide input voltage range 1.kV isolation UL certified Efficiency up to 88% Fixed operating frequency Six-Sided continuous shield No minimum load required The series are ultraminiature wide input voltage range power / converters in a case half the size of industry standard 15W converters. Despite their small size, the converters are fully specified devices with output currents up to Amps, no minimum load, 100V isolation and low ripple/noise figures. The outputs are also fully protected against short circuits, overcurrent and overvoltage. The series will find many uses in applications where board space and/or board height is at a premium. / Converter 15 Watt 1 x 1 & Output YEAR w a r r a n t y Selection Guide Part Number Input Output Output Input (1) Efficiency (1) Max. Capacitive Voltage Range Voltage Current Current typ. Load (2) [V] [V] [ma] [ma] [%] [µf] RP15-2.SAW (,) 9-. 000 0 8 12000 RP15-205SAW (,) 9-5 000 727 8 000 RP15-212SAW (,) 9-12 100 77 87 1000 RP15-215SAW (,) 9-15 1000 718 87 0 RP15-8.SAW (,) 18-75. 000 20 8 12000 RP15-5SAW (,) 18-75 5 000 59 87 000 RP15-812SAW (,) 18-75 12 100 7 87 1000 RP15-815SAW (,) 18-75 15 1000 59 87 0 RP15-205DAW (,) 9- ±5 ±1500 75 85 ±000 RP15-212DAW (,) 9- ±12 ±25 718 87 ±520 RP15-215DAW (,) 9- ±15 ±500 710 88 ±0 RP15-5DAW (,) 18-75 ±5 ±1500 8 85 ±000 RP15-812DAW (,) 18-75 ±12 ±25 8 ±520 RP15-815DAW (,) 18-75 ±15 ±500 59 87 ±0 Note1: Measured at nominal input voltage and full load Note2: Measured at minimum input voltage and constant resistive load Model Numbering Input Voltage Output Voltage or RP15- _AW/ Package () Control Logic () UL0950-1 Certified E198 Ordering Examples RP15-205SAW/P = 2V :1 Input, 5V Output, Positive Logic CTRL pin and Trim pin fitted. RP15-5DAW-HC = 8V :1 Input, ±5V Output, Premounted Heat-sink (no trim pin with dual output) Note: standard part is without suffix P or N = without CTRL & Trim function Trim function is only available for single output with /P or /N suffix add suffix P for CTRL function with positive logic (1=ON, 0=OFF) and trim pin for single output add suffix N for CTRL function with negative logic (0=ON, 1=OFF) and trim pin for single output Note: add suffix -HC for premounted Heat-sink and clips www.recom-power.com REV.: /2018 PD-1
/ Converter BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Internal Input Filter Input Voltage Range Input Surge Voltage Under Voltage Lockout (UVLO) Input Reflected Ripple Current (5) nom. Vin = 2V nom. Vin = 8V Vin = 2V, 100ms max. Vin = 8V, 100ms max. Vin = 2V Vin = 8V - ON - OFF - ON - OFF 9V 18V 2V 8V 8V 1V 0mAp-p Pi-Type V 75V 50V 100V Output Voltage Trimming () Output ±10.0% Minimum Load 0% Start-up time ON/OFF Control (7) Positive Logic Negative Logic Power up ON/OFF CTRL - ON - OFF - ON - OFF 9V 18V 0ms 0ms Open or < Vr < 15V Short or 0 < Vr < 1.2V Short or 0 < Vr < 1.2V Open or < Vr < 15V Input Current of CTRL Pin - ON -0.5mA 1.0mA Standby Current - OFF 2.5mA Internal Operating Frequency 0kHz 00kHz 0kHz Ripple and Noise measured by 20MHz bandwidth with a 1µF M/C X7R and 10µF T/C with a 1µF M/C X7R and 10µF T/C.Vout, 5Vout 12Vout, 15Vout 75mVp-p 100mVp-p with a 1µF M/C X7R and 10µF T/C all models 100mVp-p Note5: Simulated source impedance of 12μH. 12μH inductor in series with +Vin Note: Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an external resistor between the Trim pin and either +Vout pin or -Vout pin Note7: The ON/OFF control function can be positive or negative logic. The pin voltage is referenced to -Vin pin. If no suffix is specified, the control pin will be omitted RP15-205SAW Efficiency vs. Output Current Efficiency vs. Input Voltage 95 95 90 85 90 Efficiency [%] 75 70 5 0 55 50 5 0 10 Output Current [%] 9Vin 2Vin Vin 20 0 0 50 0 70 90 100 Efficiency [%] 85 75 70 5 0 9 12 15 18 21 2 27 0 Input Voltage [V] continued on next page PD-2 REV.: /2018 www.recom-power.com
/ Converter RP15-5SAW Efficiency [%] 95 90 85 75 70 5 0 55 50 5 0 10 Efficiency vs. Output Current Output Current [%] 18Vin 8Vin 75Vin 20 0 0 50 0 70 90 100 Efficiency [%] 95 90 85 75 70 5 18 Efficiency vs. Input Voltage 2 0 2 8 5 0 75 Input Voltage [V] External Output Trimming Output Voltage Trimming output Powerline converters offer the feature of trimming the output voltage over a certain range around the nominal value by using external trim resistors. No general equation can be given for calculating the trim resistors, but the following trimtables give typical values for chosing these trimming resistors. If voltages between the given trim points are required, extrapolate between the two nearest given values to work out the resistor required or use a variable resistor to set the output voltage. Output can be externally trimmed by using the method shown below. TRIM UP TRIM DOWN RU RD RP15-xx.SAW 5 5 Trim up 1 2 5 7 8 9 10 % Vout =...99.2.5.98.51.5.597. Volts R U = 85.071 191.511 12.990 9.70 75.7 2.70 5.25.0 0.9.2 kohms Trim down 1 2 5 7 8 9 10 % Vout =.27.2.201.18.15.102.09.0.00 2.97 Volts R D = 11.719 5.779.1 2.810 17.1 1.8 10.57 8.25.0 5.228 kohms RP15-xx05SAW Trim up 1 2 5 7 8 9 10 % Vout = 5.05 5.10 5.15 5.20 5.25 5.0 5.5 5. 5.5 5.50 Volts R U = 25.50 125.700 8.117 1.825 9.050 0.5.50 29.888 2.9 2.500 kohms Trim down 1 2 5 7 8 9 10 % Vout =.95.90.85..75.70.5.0.55.50 Volts R D = 28.0 120.590 78.007 5.715.90 5.2 29.0 2.778 21.229 18.90 kohms RP15-xx12SAW Trim up 1 2 5 7 8 9 10 % Vout = 12.12 12.2 12. 12.8 12.0 12.72 12.8 12.9 1.08 1.20 Volts R U = 20.22 99.057..97.557 29.12 2.52 20.92 18.08 15.72 kohms Trim down 1 2 5 7 8 9 10 % Vout = 11.88 11.7 11. 11.52 11.0 11.28 11.1 11.0 10.92 10.8 Volts R D = 77.557 08.72 28.779 182.7 1.22 11.8 97.985 8.88 72.85.057 kohms continued on next page www.recom-power.com REV.: /2018 PD-
/ Converter RP15-xx15SAW Trim up 1 2 5 7 8 9 10 % Vout = 15.15 15. 15.5 15.0 15.75 15.90 1.05 1.20 1.5 1.50 Volts R U = 11.557 78.22 50..557 28.22 22.8 18.700 15.72 1.09 11.557 kohms Trim down 1 2 5 7 8 9 10 % Vout = 1.85 1.70 1.55 1.0 1.25 1.10 1.95 1. 1.5 1.50 Volts R D = 818.22 01.557 22.8 19.22 151.557 12.779 10.98 89.057 77.8 8.22 kohms REGULATIONS Parameter Condition Value Output Voltage Accuracy ±1.0% Line Voltage Regulation Load Voltage Regulation 0% to 100% load Cross Regulation asymmetrical 25%<>100% load ±5.0% ±0.2% ±0.5% ±0.2% ±1.0% Transient Response 25% load step change recovery time 250μs typ. PROTECTIONS Parameter Condition Value Short Circuit Protection (SCP) Over Voltage Protection (OVP) Over Load Protection (OLP) Isolation Voltage Zener Diode Clamp tested for 1 minute.vout 5Vout 12Vout 15Vout I/P to O/P I/P (O/P) to case continuous, automatic recovery.7-5.v 5. - 7.0V 1.5-19.V 1.8-20.5V Hiccup mode, 150% of rated Iout typ. 1.kV 1.0kV Isolation Resistance tested with 500V 1GΩ min. Isolation Capacitance Note8: This power module is not internally fused. An input line fuse must always be used. Recom suggests: 2Vin= T.15A; 8Vin= T1.A slow blow types 1000pF max. PD- REV.: /2018 www.recom-power.com
/ Converter ENVIRONMENTAL Parameter Condition Value Operating Temperature Range Maximum Case Temperature Temperature Coefficient Thermal Impedance Operating Humidity Thermal Shock Vibration MTBF Derating Graph (10) RP15-5SAW without derating with derating natural convection 0.1m/s (20LFM) according to MIL-HDBK-217F, G.B. Bellcore TR-NWT-0002 (9) +25 C RP15-5SAW -0 C to +7 C -0 C to +105 C +105 C ±0.02%/ C max. 18.2 C/Watt 15.8 C/Watt 5% - 95% RH according to MIL-STD-810F according to MIL-STD-810F 159 x 10 hours 10 x 10 hours 100 100 Output Power [%] 0 0 20 Output Power [%] 0 0 20 0-0 -20 0 20 0 0 7 Ambient Temperature [ C] 100 120 105 0-0 -20 0 20 0 0 100 120 7 105 Ambient Temperature [ C] Note9: BELLCORE TR-NWT-0002. Case l: 50% Stress, Ta= 0 C. MIL-HDBK 217F Notice 2. Ta = 25 C, full load, (controlled environment). Note10: Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part number not shown here please contact our technical support service at techsupportat@recom-power.com. SAFETY AND CERTIFICATIONS Certificate Type (Safety) Report / File Number Standard Information Technology Equipment, General Requirements for Safety E198 UL0950-1 1st. Ed.: 200 C22.2 No. 0950 1st. Ed.: 200 EMC Compliance Condition Standard / Criterion Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement with external filter EN55022, Class A or B ESD Electrostatic discharge immunity test Air ±8kV and Contact ±kv EN1000--2, Criteria A Radiated, radio-frequency, electromagnetic field immunity test 10V/m EN1000--, Criteria A Fast Transient and Burst Immunity (11) ±2kV EN1000--, Criteria A Surge Immunity (11) ±1kV EN1000--5, Criteria A Immunity to conducted disturbances, induced by radio-frequency fields Vr.m.s EN1000--, Criteria A continued on next page www.recom-power.com REV.: /2018 PD-5
/ Converter Note11: An external input filter capacitor is required if the module has to meet EN1000--, EN1000--5. The filter capacitor Recom suggests: Nippon chemi-con KY series, 220μF/100V EMI Filtering Class A C Fuse Input C1 C2 +VIN +VOUT -V OUT -VIN C MODEL C1 C2 C/C RP15-2xxS_DAW.8μF/50V.8μF/50V 70pF/2kV 18 MLCC C RP15-8xxS_DAW 70pF/2kV 18 MLCC Fuse Input C1 C2 +VIN +VOUT -VOUT -VIN C EMI Filtering Class B C5 Input Fuse C1 C2 L1 C +VIN +VOUT MODEL C1 C2 C -VIN -VOUT RP15-2xxS_DAW.8μF/50V N/A.8μF/50V C RP15-8xxS_DAW C5 MODEL C/C5 L1 Input Fuse C1 C2 L1 C +VIN +VOUT RP15-2xxS_DAW RP15-8xxS_DAW 70pF/2kV 18 MLCC 1000pF/2kV 18 MLCC CMC: 25μH ref: WE 729021; ref.: CMC-0 25μH ref: WE 729021; ref.: CMC-0 -V OUT -VIN C PD- REV.: /2018 www.recom-power.com
/ Converter DIMENSIONS and PHYSICAL CHARACTERISTICS Parameter Type Value Material Package Dimensions (LxWxH) Package Weight Dimension Drawing (mm) Case Base Potting Nickel coated copper FR PCB Epoxy (UL9-V0) 25. x 25. x 9.9mm 1. x 25. x 1.5mm 15g 21.5g 25. 25. 9.9 5. 8 x = 20.2 Ø 1.0 ±0.1 Recommended Footprint Details 12.70 5.08 10.2 1 2 Bottom View 7.2 2 5 Top View 5 1 Pin Connections Pin # /P or /N /P or /N www.recom-power.com 1 +Vin +Vin +Vin +Vin 2 -Vin -Vin -Vin -Vin no Pin CTRL no Pin CTRL +Vout +Vout +Vout +Vout 5 no Pin Trim Com Com -Vout -Vout -Vout -Vout Pin Pitch Tolerance ±0.25mm XX.X ± 0.5mm XX.XX ± 0.25mm continued on next page REV.: /2018 PD-7
/ Converter Dimension Drawing (mm) 25. 25. Top View Heat-sink Pin Connections 1. 5.85 2.2 Pin # /P or /N /P or /N 1 +Vin +Vin +Vin +Vin 9.9 1.5 2 -Vin -Vin -Vin -Vin no Pin CTRL no Pin CTRL +Vout +Vout +Vout +Vout 8 x = 20.2 5. Ø 1.0 ±0.1 Recommended Footprint Details 5 no Pin Trim Com Com -Vout -Vout -Vout -Vout Pin Pitch Tolerance ±0.25mm XX.X ± 0.5mm XX.XX ± 0.25mm 12.70 5.08 10.2 1 2 Bottom View 7.2 2 5 Top View 5 1 PACKAGING INFORMATION Parameter Type Value Packaging Dimensions (LxWxH) Packaging Quantity Storage Temperature Range Storage Humidity Tube Tray Tube Tray 20.0 x 1.0 x 28.0mm 20.0 x 1.0 x 28.0mm 8pcs 20pcs -55 C to +125 C 5% - 95% RH The product information and specifications may be subject to changes even without prior written notice.the product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM s explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. PD-8 REV.: /2018 www.recom-power.com