SF Santa Fe Small/Medium/Large

SF Santa Fe Small/Medium/Large square luminaires Square, formed, two-piece aluminum housing; Standard reveal accentuated with color vinyl trim stripe Extruded aluminum door with clear, flat tempered glass lens, fully gasketed to housing; Tool-free access to lamp provided with four spring-loaded latch/hinges Specular, anodized aluminum reflectors for horizontal lamp provide Type II, III, IV, or V square light patterns; SF1 and SF2, Type II and Type III reflectors feature unique, micro-faceted design; Segmented Type III reflector with Santa Fe large (SF3); Tool-less fasteners allow access to ballast; IESNA full cut-off lighting classification achieved with flat lens IDA fixture seal of approval Extruded aluminum arm required for pole mount; Spider mount has four tubular arms attaching housing to pole top fitter; Yoke mount has two square aluminum arms securing housing to pole top fitter; Cast aluminum wall bracket available Mogul porcelain socket, pulse-rated, with springloaded, nickel-plated center contact and reinforced lamp grip screw shell; Medium base for ED-17 lamp 100w - 150w lag type HPF ballast, starting rated at -20 F (-40 F for HPS) 200w - 400w CWA type ballast, HPF, starting rated at -20 F (-40 F for HPS) Durable Lektrocote TGIC thermoset polyester powder coat paint finish assures long life and maintenance-free service Listed to UL1598 for use in wet locations Ordering Information series SF1 Santa Fe 1 (100-250w) SF2 Santa Fe 2 (200-400w) SF3 Santa Fe 3 (1000w) mount A Arm mount (arm not included, order separately) S5 Spider mount - internal Slipfitter (5 sq. pole) SF3 only S6 Spider mount - internal slipfitter (6 sq. pole) SF3 only ST Spider mount (2.375 tenon) Y5S Yoke mount - pad (5 sq. steel pole) Y5A Yoke mount - pad (5 sq. alum. pole) Y6S Yoke mount - pad (6 sq. steel pole) SF1, SF3 only Y6A Yoke mount - pad (6 sq. alum. pole) SF1, SF3 only YT Yoke mount (2.375 tenon) LAMP ORIENT./DISTR. H2 Horiz. II SF1, SF2 only H3 Horiz. III H4 Horiz. IV H5 Horiz. V (square) 1 Factory wired for highest voltage unless specified 2 Required for 90 configurations 3 Reveal will match paint color when none indicated see page 615 for accessories B Arm Mount source/wattage Metal Halide H1K 1000w (BT-56) SF3 only super Metal Halide MS1K 1000w (BT-56) SF3 only pulse start Metal Halide P10 100w (ED-17) SF1 only P12 125w (ED-17) SF1 only P15 150w (ED-28) SF1 only P20 200w (T-15) SF2 only P25 250w (ED-28) SF2 only P32 320w (ED-28) SF2 only P35 350w (ED-28) SF2 only P40 400w (ED-28) SF2 only high pressure sodium S15 150w (ED-23.5) SF1 only S25 250w (ED-18) SF2 only S40 400w (ED-18) SF2 only S1K 1000w (E-25) SF3 only A C Yoke Mount F D LENS F Flat voltage Q 1 Quad-Tap 120/208/240/277V 5 480V T 1 Tri-Tap 120/277/347V COLOR RD Red Spider Mount A B C D 9 17 28 5/16 21 7/8 1.3 ft² 23 lbs. SF1 229 mm 432 mm 719 mm 556 mm 0.1 m² 10.4 kg 10 21 33 3/4 22 3/8 1.9 ft² 40 lbs. SF2 254 mm 533 mm 857 mm 568 mm 0.2 m² 18.1 kg 14 24 41 5/16 27 3/4 2.9 ft² 84 lbs. SF3 356 mm 610 mm 1049 mm 705 mm 0.3 m² 29 kg Note: Note: Note: OPTIONS F(X) Fusing (replace X with voltage: 1-120, 2-208, 3-240, 4-277, 5-480, 6-347) P(X) Photo button (replace X with voltage: 1-120, 2-208, 3-240, 4-277, 6-347) PR(X) Photo cell receptacle (replace X with voltage: 1-120, 2-208, 3-240, 4-277, 5-480, 6-347) QZ Quartz restrike with lamp HS Internal house-side Shield VG Polycarbonate vandal guard R(XX) 3 Reveal (replace XX with color) L Lamp arm logic (order separately) series Rigid arm luminaire shape S Square/ rectangular Arm Length 6 6" Arm ( = 0.24 ft 2, 3.5 lbs) (0.02 m 2, 1.5 kg) 10 2 10" Arm ( = 0.4 ft 2, 5.0 lbs) (0.03 m 2, 2.2 kg) pole shape #1 drill pattern S Square R4 Round straight (4.5") R5 Round straight (5") R6 Round straight (6") #2 drill pattern T2 Round tapered (2.5") T3 Round tapered (3") T35 Round tapered (3.5") T4 Round tapered & straight (4") COLOR RD Red and weight values do not include mounting arm Spider mount adds: SF1-0.1 ft 2 (2 lbs), SF2-0.3 ft 2 (3 lbs), SF3-0.4 ft 2 (2 lbs) Yoke mount adds: SF1-1.0 ft 2 (6 lbs), SF2-1.6 ft 2 (9 lbs), SF3-1.9 ft 2 (11 lbs) See Spaulding Value pgs. 622-623 for more detailed information. 592

Accessories oakland 3 - LPS Accessories -S-6-S-XX 1 6" arm for square pole -S-6-R4-XX 1 6" arm for 4.5" dia. round -S-6-R5-XX 1 6" arm for 5" dia. round straight pole -S-6-R6-XX 1 6" arm for 6" dia. round straight pole -S-6-T2-XX 1 6" arm for 2 3 /8 to 2 5 /8" dia. -S-6-T3-XX 1 6" arm for 2 3 /4 to 3 1 /8" dia. -S-6-T3.5-XX 1 6" arm for 3 1 /4 to 3 3 /4" dia. -S-6-T4-XX 1 6" arm for 3 7 /8 to 4" dia. round straight and tapered pole -S-10-S-XX 1 10" arm for square pole -S-10-R4-XX 1 10" arm for 4.5" dia. round -S-10-R5-XX 1 10" arm for 5" dia. round -S-10-R6-XX 1 10" arm for 6" dia. round -S-10-T2-XX 1 10" arm for 2 3 /8 to 2 5 /8" dia. -S-10-T3-XX 1 10" arm for 2 3 /4 to 3 1 /8" dia. -S-10-T3.5-XX 1 10" arm for 3 1 /4 to 3 3 /4" dia. -S-10-T3.5-XX 1 10" arm for 3 7 /8 to 4" dia. round straight and tapered pole PTL-1 (120V) PTL-8 (120, 208, 240, 277V) PTL-5 (480V) PTL-6 (347V) PSC Shorting Cap - Twistlock 1 Replace XX with color choice, eg.: DB for Dark Bronze PTL-1 PTL-8 PTL-5 PTL-6 PSC orlando & orlando dome Accessories Photocontrol - Twistlock cell (120V) Photocontrol - Twistlock cell (120, 208, 240, 277V) Photocontrol - Twistlock cell (480V) Photocontrol - Twistlock cell (347V) Shorting Cap - Twistlock raven Accessories RCS rcs-hs-23 Internal lamp shielding (RCS - H2 & H3 distributions) rcs-hs-2p Internal lamp shielding (RCS - H2P & distributions) rcs-hs-3p Internal lamp shielding (RCS - H3P distribution) rcs-hs-4 Internal lamp shielding (RCS - H4 distribution) rcs-pvg 1 8" Polycarbonate vandal guard suspended 3" below door frame RCL rcl-hs-23p Internal lamp shielding (RCL - H2P & H3P distributions) rcl-hs-4 Internal lamp shielding (RCL - H4 distribution) rcl-hs-4p Internal lamp shielding (RCL - H4P distribution) rcl-pvg 1 8" Polycarbonate vandal guard suspended 3" below door frame additional accessories f-rpa2-xx 1,2 Round pole adapter (2 3/4-3 1 /8") f-rpa3-xx 1,2 Round pole adapter (3 1/4-3 3 /4") f-rpa4-xx 1,2 Round pole adapter (3 7/8-4 1 /2") f-rpa5-xx 1,2 Round pole adapter (5") f-rpa6-xx 1,2 Round pole adapter (6") WB-CR-XX 1 Wall bracket ptl-1 Photocontrol - Twist-Lock cell (120V) ptl-8 Photocontrol - Twist-Lock cell (120-277V) ptl-5 Photocontrol - Twist-Lock cell (480V) ptl-6 Photocontrol - Twist-Lock cell (347V) psc Shorting cap - Twist-Lock FDmLH Flush mount hardware kit -F-4-S-XX 1 4'' Arm -F-10-S-XX 1 10'' Arm santa fe Accessories 8914515 SF1 Internal house-side-shield, Type II, III, IV, V 8914516 SF2 Internal house-side-shield, Type II, III, IV, V 8914517 SF3 Internal house-side-shield, Type III, IV, V PTL-1 (120V) PTL-8 (120, 208, 240, 277V) PTL-5 (480V) PTL-6 (347V) PSC Shorting cap - Twistlock WB-S-XX 1 Wall bracket MAF-XX 1 Mast Arm Fitter 1 Replace XX with color choice, eg.: DB for Dark Bronze washington Accessories 8914529 House-side shield 8914528 House-side shield 8914548 House-side shield PBT-1 Photocontrol, button type (120V only) PBT-234 Photocontrol, button type (208-240-277V) luminaire accessories 1 Replace XX with color choice, eg.: DB for Dark Bronze 2 When ordering poles, specify Pole Drill Pattern #2 615

Mounting Accessories mounting accessories 616 Tenon Adapters For use with: AL, MY, OR, OD, WN, DL, SF, NK, OK (#1 Drill Pattern) FEA-2-XX Triangular steel adapter at 120 deg..5 (0.05) 17 FEA-3-XX Triangular steel adapter at 120 deg..5 (0.05) 17 2-SA-SGL-D-XX SQ steel adapter - SGL.3 (0.03) 10 2-SA-D90-XX SQ steel adapter - DBL at 90 deg..3 (0.03) 10 2-SA-D180-XX SQ steel adapter - DBL at 180 deg..3 (0.03) 10 2-SA-TPL-D90-XX SQ steel adapter - TPL at 90 deg..3 (0.03) 10 2-SA-QD-D-XX SQ steel adapter - QUAD at 90 deg..3 (0.03) 10 2-RA-SGL-D-XX 1 RD steel adapter - SGL.2 (0.02) 9 2-RA-D90-XX 1 RD steel adapter - DBL at 90 deg..2 (0.02) 9 2-RA-D180-XX 1 RD steel adapter - DBL at 180 deg..2 (0.02) 9 2-RA-TPL-D90-XX 1 RD steel adapter - TPL at 90 deg..2 (0.02) 9 2-RA-TPL-D120-XX 1 RD steel adapter - TPL at 120 deg..2 (0.02) 9 2-RA-QD-D-XX 1 RD steel adapter - QUAD at 90 deg..2 (0.02) 9 All tenon adapters slipfit over 2 3/8 OD tenon; Accommodates #1 hole pattern for arms 1 Requires appropriate 4 1/2 round pole adapter For use with: CR1, RCS, RCL, MSV, CM1, and CM2 (#2 Drill Pattern) SETA-XX 1 4" Square pole top tenon adapter; 2 3/8 OD slipfitter for max. four fixtures (90 ) RETA-XX 1 4" Round pole top tenon adapter; 2 3/8 OD slipfitter for max. four fixtures (90 ); Order 4" round pole adapters 0.2 (0.02) 20 (9) separately TETA-XX 1,2 Three sided pole top tenon adapter; 2 3/8 OD slipfitter for max. three fixtures (120 ) For use with: DM (#6 Drill Pattern) SSS-490-XX 1 4" Square pole top tenon adapter; 2 3/8-2 7/8 OD slipfitter for max. four fixtures (90 ) RSS-490-XX 1 4" Round pole top tenon adapter. 2 3/8-2 7/8 OD slipfitter for max. four fixtures (90 ); Order RSD-04-X 0.2 (0.02) 20 (9) (one per fixture) separately RSS-3120-XX 1 4" Round pole top tenon adapter; 2 3/8-2 7/8 OD slipfitter for max. three fixtures (120 ) 0.2 (0.02) 20 (9) For use with: MSS and DS (#4 Drill Pattern) MSS-90-X 1 4" Square pole top tenon adapter; 2 3/8-2 7/8 OD slipfitter for max. four fixtures (90 ) 1 Replace X or XX with color designation (See bottom right of page) 2 Must use 10 arm on fixture for 120 mounting Tenon Brackets and Arms AFB-1 AFB-1-M53 241-C-XX FLB-12-XX Flat surface bracket - natural aluminum finish Flat surface bracket - gray finish Flat surface bracket - 90 (lag bolt hole spacing is 6.75 on OC, mounting hardware by others) 12 floodlight bracket for pole mounting (bracket requires internal pole access) 16.5 (.05) 6 FLB-24-XX 24 floodlight bracket for pole mounting 1.0 10 (bracket requires internal pole access) (.10) SSS-T4-DB 2 3/8" OD Tenon top adapter for 4 square open top poles, 17.5 (8) bronze finish (slips 9" into pole aligns with #6 drill pattern) SSS-T5-DB 4 2 3/8" OD Tenon top adapter for 5 square open top poles, bronze finish (slips 9" into pole aligns with #6 drill pattern) 14.5 (6.6) TPR-2-M5X 1 2 1/2 to 2 pipe size tenon reducer 6 (2.7) TPR-3-M5X 2 3 to 2 pipe size tenon reducer 8 (3.6) TPR-4-M5X 3 4 to 2 pipe size tenon reducer 9 (4.1) TA-4 2 3/8 OD Tenon top adapter for 4 square pole (11 GA pole) TA-5 2 3/8 OD Tenon top adapter for 5 square pole (11 GA pole) TA-6 2 3/8 OD Tenon top adapter for 6 square pole (11 GA pole) 285-B-3-XX 3 1/2 to 2 3/8 Reducer (OD for both dimensions) 285-B-4-XX 4 1/2 to 2 3/8 Reducer (OD for both dimensions) 1 Bracket slips over pole creating 2 3/8 OD tenon (lower ID = 3 1/16 ) 2 Bracket slips over pole creating 2 3/8 OD tenon (lower ID = ID = 3 1/2 ) 3 Bracket slips over pole creating 2 3/8 OD tenon (lower ID = ID = 4 5/8 ) 4 Will not fit in 3 gauge poles Note Brackets Bronze color standard; For other colors add suffix to catalog number: -M50 Black finish, -M52 White finish; -M53 Gray finish 15 5" 11" FEA 6-5/8" SETA-XX RSS-490-XX RSS-3120-XX 4 AFB-1 SSS-TX 5.25" 6.75" 120 9.5 9.5 TPR 11" Replace XX with Color Designation RD Red (Premium Color) (Premium Color) 2-RA RETA-XX 4-1/2" 4 4 241-C 13" 8" sq. 10" 9.5 SSS-490-XX MSS-90-X TA-X 4 2-SA FLB-12/24 4" sq. 10-1/2" 13 3/4 5 2-3/8" OD tenon hole spacing 4 1/4 3 Sq. tubing 12"/ 24" 2-3/8" OD TETA-XX 4 285-B Replace X with Color Designation 1 Dark Bronze 2 Black 3 Gray 4 White 5 Platinum Silver 6 Red 7 Forest Green

Mounting Accessories 6" 4" AASF Adjusts in 5 increments SMA-X-XX MAL-211 46" CLB-2 TPLB AADM Adjusts in 5 increments Mounting Brackets For use with: MY, OR, OD, WN, DL, SF, NK, OK Round luminaires require use of standard 6 arm between bracket & luminaire SMA-1-XX 1 Single mounting arrangement, 1 ft. arm.3 6 SMA-2-XX 1 Single mounting arrangement, 2 ft. arm.6 10 SMA-3-XX 1 Single mounting arrangement, 3 ft. arm.9 15 SMA-4-XX 1 Single mounting arrangement, 4 ft. arm 1.2 18 1 Replace X or XX with color designation (see bottom left of page) Twin Parallel Brackets For use with: DM MAL-211-X 1 Twin parallel mount - 30 on center / 4 arms for 2 3/8 OD tenon, includes two MAL-4-X series arms For use with: AL, MY, OR, OD, WN, DL, SF, NK, OK3 CLB-2-XX 1 Twin parallel mount for two luminaires, mounts to pole with four bolts, pole must be configured with A1 or C1 drill pattern For use with: CR1, RCS, RCL, CM1, CM2, MSV TPLB-XX 1 Twin parallel luminaire bracket, must be configured with A2 or C2 drill pattern 1 Replace X or XX with color designation (see bottom left of page) (.2) 34.6 (15.7) 2.4 (1.1) mounting accessories 2-3/8" OD Slipfitter 4" BC 2" MAS-TK-X -CR-TK-TA-X -F-TK-TA-X Adjusts in 4 increments MAL-KF-X Replace XX with color designation RD Red (Premium Color) (Premium Color) 4" Mounting Pattern for AADM -CR-K-S-X -F-K-S-X Adjusts in 4 increments Replace X with color designation 1 Dark Bronze 2 Black 3 Gray 4 White 5 Platinum Silver 6 Red 7 Forest Green Adjustable Mounting Arms For use with: MSS MAS-K-X 1 2 3/8 OD tenon slipfitter for single fixture 5 (2.3) MAS-TK-X 1 2 3/8 OD tenon slipfitter for twin fixtures (180 ) 7 (3.2) For use with: MY, OR, OD, WN, DL, SF, NK AASF-XX 1,3 Adjustable slipfitter mounting arm 10 (4.5) AADM-XX 1,2 Adjustable direct mounting arm 5 (2.3) 1 Replace X or XX with color designation (see bottom left of page) 2 Arm utilizes #1 hole pattern 3 Arm utilizes #1 hole pattern on luminaire end For use with: RCS, RCL, MSV -F-K-TA-XX 1 2 3/8 OD tenon slipfitter for single fixture 5 (2.3) -F-TK-TA-XX 1 2 3/8 OD tenon slipfitter for twin fixture (180 ) 7 (3.2) -F-K-S-XX 1,3 10 Adjustable arm 0.5 (0.05) 5.75 (2.6) For use with: CR1, CM1 & CM2 2 -CR-K-TA-XX 1 2 3/8 OD tenon slipfitter for single fixture 5 (2.3) -CR-TK-TA-XX 1 2 3/8 OD tenon slipfitter for twin fixture (180 ) 7 (3.2) -CR-K-S-XX 1,3 10 Adjustable arm 0.5 (0.05) 5.75 (2.6) 1 Replace XX with color designation (see bottom left of page) 2 CM1, CM2 must use in conjunction with rigid arm 3 Direct pole mount only, not compatible with tenon adapters 617

Mounting Accessories luminaire mounting detail Mast Arm Fitter For use with: AL, CM1, CM2 MAF-CM-XX 1 Horizontal mast arm fitter for 2 3/8 OD arm For use with: OR, OD, DL, SF, NK, OK MAF-XX 1 Horizontal mast arm fitter for 2 3/8 OD arm For use with: CR1, RCS, RCL, MSV -XX-K-TA 1 Use mounting arm, see p. 617 MAF-CM-XX 1 Replace XX with Color Designation RD Red (Premium Color) (Premium Color) MAF-XXX AL, DL, DT2, MY, NK, OD, OR, SF, WN S Ø.438 4 S SQ. COVER 1.25 E SQ. COVER 4.0 BOLT 1.0 DL, MY, NK, OD, OR, PF, WN LATE DT2 #1 DRILL #1 drill PATTERN pattern FOR S ARE AL COVER AL, DL, MY, NK, OD, OR, WN ROUND STRAIGHT S (4.5 OD & LARGER) Ø.438 4 S RND. COVER DL, MY, NK, OD, OR, PF, WN AL, DL, MY, NK, OD, OR, WN ROUND TAPERED S & ROUND STRAIGHT S (FOR 4 OD & SMALLER) P TAPERED COVER 2.25 1.25.875 1.0 #1 drill pattern 4.0 ROUND RND. COVER AL ROUND ADAPTER STRAIGHT ROUND (41/2" - 6") BOLT 3.5 Ø.563 2 S #2 drill pattern TAPERED COVER TAPERED ADAPTER BOLT TAPERED ROUND & 4" STRAIGHT ROUND SQ. COVER SQ. COVER COVER TAPERED ADAPTER COVER RND ADAPTER ROUND STRAIGHT ROUND (41/2" - 6") TAPERED TAPERED ROUND & 4" STRAIGHT ROUND 618

Mounting Details P.875 2.25 3.5 Ø.563 2 S #2 drill pattern STANDARD DETAIL COVER CAST ADAPR ROUND SQ. COVER SCREW CM1, CM2 CM1, CM2, CR1, MSV, RCL, RCS ALL SHAPES GASKET FLATWASHER FLAT WASHER HEX NUT COVER COVER BOLTS FROM INSIDE FIXTURE (3- (PATTERN END) COVER THREADED ROD HEX NUT FLAT WASHER GASKET RETAINER WASHER COVER NUTPLATE ROUND NUT COVER FLAT WASHER GASKET THREADED RODS ROUND ADAPTER RCL, RCS, MSV luminaire mounting detail CAST ADAPTER (3- PATTERN E CR1 ROUND & ROUND S DS, MSS ALL SHAPES DT3 S Ø.438 3 S Ø.563 4 S 3.625 1.25 4.0 2.375 MAL-10-X / MAL-4-X mas-4-x / mas-10-x 1.0 1.187 #4 drill pattern #5 drill pattern DM ALL SHAPES Ø.438 3 S P 3.625 4.062 34 #6 drill pattern MAL-10-X mal-4-x / mal-10-x / MAL-4-X msv-4-x / msv-10-x KEY AL Alaire CR1 Cimmarron CM1/CM2 Medallion - Sm/Lg RCS/RCL Raven - Sm/Lg DT2 Detriot 2 DT3 Detriot 3 MSS Magnuspec MSV M-Pulsive NK SF MY WN DL DS DM OD OR Newark - Sm/Med Santa Fe - Sm/Med/Lg Monterey - Sm/Med/Lg Washington - Sm/Med/Lg Dallas - Sm/Med/Lg Small Magnudisc Med Magnudisc Orlando Dome - Med/Lg Orlando Round - Med/Lg 619