O.D. Mounted Machine Tools - Pipe Ranges

O.D. Mounted Machine Tools - Pipe Ranges ½in 13mm 12in 305mm 24in 610mm 36in 914mm 48in 1219mm 60in 1524mm 72in 1829mm 90in 2286mm 120in 3048mm SDSF 1.0 SDSF 2.0 LDSF HDSF DYNAPREP LCSF SDSF SDSF 3.0 SDSF 4.0 SDSF 5.0 SDSF 6.0 LCSF 206 LCSF 408 LCSF 610 LCSF 612 LCSF 814 LCSF 1016 LCSF 1420 LCSF 1824 LCSF 2228 LCSF 2632 LCSF 3036 LCSF 3642 LCSF 4248 MDSF 612 MDSF 814 MDSF 1016 MDSF 1218 MDSF 1420 MDSF 1824 HDSF 1224 HDSF 2436 HDSF 3648 HDSF 4860 HDSF 6072 HDSF 7284 LDSF 75 LDSF 90 LDSF 105 LDSF 120 TRAV-L- CUTTER MODEL E (PNEUMATIC) MODEL HE (HYDRAULIC) GUILLOTINE SUPER C MODEL D SUPER D GOLIATH 2 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com

SDSF Small Diameter Split Frame The Small Diameter Split Frame (SDSF) is an externally mounted machine tool for cutting, beveling, and counterboring pipe from 0.5in to 6in (ND15-150) diameter. The SDSF is also capable of performing socket weld removal and chipless wheel cutting. Lightweight and flexible, the SDSF is optimized for low clearance environments. It offers simple setup and operation, featuring a self-squaring clamping system for precise cutting results typically available only with fixed machine tools. The SDSF operates on air or electric power using standard Wachs motors and adapters. A variety of tool slides and other accessories are interchangeable between many SDSF models. Best of all, the SDSF features E.H. Wachs legendary durability and is designed and built for years of reliable service. SDSF MODELS MODEL PIPE SIZE (in) PIPE SIZE (DN) SDSF 1.0 1/2-1in DN15-25 SDSF 2.0 1-1/4-2in DN32-50 SDSF 3.0 2-3in DN50-80 SDSF 4.0 3-4in DN80-100 SDSF TOOLING SEVERING BEVEL COUNTERBORE.125in (3.2mm) width low clearance tool.125in (3.2mm) width standard tool.125in (3.2mm) width extended-reach tool 37.5 low clearance tool 37.5 standard tool 37.5 extended-reach tool 30 & 45 extendedreach tools 4:1 taper (15 ) counterbore tool PARTING TOOL SLIDE Used for parting (cutting) of pipe and tube. RADIAL SOCKET WELD SLIDE Used for radial removal of socket welds, requires less axial clearance BEVELING TOOL SLIDE Used in conjunction with parting slide to cut and bevel simultaneously AXIAL SOCKET WELD SLIDE Used for axial removal of socket welds RADIAL SOCKET WELD REMOVAL AXIAL SOCKET WELD REMOVAL.375in (9.5mm) width low clearance tool.375in (9.5mm) width standard tool.375in (9.5mm) width extended reach tool.375in (9.5mm) width low clearance tool.375in (9.5mm) width standard tool.375in (9.5mm) width extended reach tool UNIVERSAL COUNTERBORE TOOL SLIDE Use for counterboring of pipe I.D. FME TOOL SLIDE Foreign Material Exclusion, to prevent introduction of chip debris 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com 3

LCSF Low Clearance Split Frame The Low Clearance Split Frame (LCSF) is ideal for all types of pipe cutting and end-prepping. The split frame machines can be split in half or broken open, then bolted back together. This allows them to open and mount around the O.D. of in-line piping, or slipped over open-ended pipe. The LCSF has been engineered to apply precise, consistent square cuts and bevels on pipe, tube and casing the first time, every time. Using a split frame is a safe, clean operation that neither affects the metallurgical qualities of the pipe nor places airborne contaminants into the environment. 14 models are available to cut, bevel and counterbore pipe from 2in through 48in (ND50 1200)* on most wall thicknesses and alloys. LCSF MODELS MODEL PIPE SIZE (in) PIPE SIZE (DN) LCSF 204/3 2-4in DN50-100 OUT-OF-ROUND SLIDES Spring-loaded slides that track the surface of out-of-round pipe. Also applicable where centering the LCSF is difficult because of limited clearance. BRIDGE SLIDE End prep accessory for beveling, compound beveling, J preps, and counterboring, available for 12in 48in LCSFs. WORM SLIDES Heavy duty feed mechanisms for durability when cutting heavy wall pipe. UNIVERSAL COUNTERBORE TOOL SLIDE Slide with a form tool attachment for counterboring with any size LCSF. Slide mounts to bevel tool slide and is used to counterbore pipe. LCSF 206/3 2-6in DN50-150 LCSF 408/3 4-8in DN100-200 LCSF 610/3 6-10in DN150-250 LCSF 612/3 6-12in DN150-300 LCSF 814/3 8-14in DN200-350 LCSF 1016/3 10-16in DN250-400 LCSF 1420/3 14-20in DN350-500 LCSF 1824/3 18-24in DN450-600 LCSF 2228/3 22-28in DN550-700 LCSF 2632/3 26-32in DN650-800 LCSF3036/3 30-36in DN750-900 LCSF 3642/3 36-42in DN900-1050 LCSF 4248/3 42-48in DN1050-1200 I.D./O.D. MODULE Mounts to bevel tool slide, for turning the outside and inside diameter of pipe. May also be used for O.D. tapering with manual axial feed. STANDARD TOOL SLIDES Low Profile Slides, Extended Slides, and Super Extended Slides, are available LCSF SPLIT FRAME Bolted together, ready for cutting LCSF SPLIT APART Ready for mounting around pipe 4 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com

HDSF Heavy Duty Split Frame HDSF Heavy Duty Split Frame clamshell style machines are the largest and most rugged in the Wachs split frame family, and are designed to cut, bevel, single point, counterbore and face flanges on large diameter pipes from 12in to 84in O.D. (DN300-2100). Designed for parting and beveling of larger diameter pipelines in the field, the HDSF series is constructed with a bigger cross section, larger gear sets and massive hardened steel components. HDSF MODELS MODEL PIPE SIZE (in) PIPE SIZE (DN) HDSF 1224 12.75-24in DN300-600 HDSF HEAVY DUTY SPLIT FRAME HDSF 2436 24-36in DN600-900 HDSF 3648 36-48in DN900-1200 HDSF 4860 48-60in DN1200-1500 HDSF 6072 60-72in DN1500-1800 HDSF TOOLING SEVERING.25in width (6.35mm) BEVEL 37.5 bevel angle HDSF Split Frame ratcheted open for mounting SINGLE POINT For use with Single Point slide, compound bevel or J-prep bevel templates OUT-OF-ROUND SLIDES Spring-loaded slides that track the surface of outof-round pipe. CANTILEVER SLIDE Can be configured to counterbore, bevel heavy wall and face large diameter flanges HDSF IN SHIPPING CRATE Loaded with accessories, this machine is ready for cutting on arrival. DUAL DRIVE MOTOR includes two pinion drives and two drive motors 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com 5

LDSF Large Diameter Split Frame E.H. Wachs LDSF Large Diameter Split Frame is designed for cold cutting, beveling, facing and counterboring on large diameter pipes, vessels and flanges. It s been engineered to incorporate multiple advancements designed to make it stronger, faster to set up, faster to operate and even more versatile than our class leading HDSF models. Picking up where our midsize split frames leave off, four standard LDSF sizes will cover a range from 60in to 120in OD (DN1500-DN3000). LDSF MODELS MODEL PIPE SIZE (in) PIPE SIZE (DN) LDSF 75 60-75in DN 1500-1875 LDSF LARGE DIAMETER SPLIT FRAME LDSF 90 75-90in DN 1875-2250 LDSF 105 90-105in DN 2250-2625 LDSF 120 105-120in DN 2625-3000 LDSF TOOLING SEVERING.25in width (6.35mm) BEVEL 37.5 bevel angle OUT-OF-ROUND SLIDES Spring-loaded slides that track the surface of out-of-round pipe. SINGLE POINT For use with Single Point slide, compound bevel or J-prep bevel templates COUNTERBORE AND REVERSE BEVELING MODULE Single Pointing Tool Slide performs perpendicular and angled counterbore. LDSF IN SHIPPING CRATE Loaded with accessories, this machine is design for quick, easy assembly. CANTILEVER SLIDE Single Pointing Tool slide can be configured to counterbore, bevel heavy wall and face large diameter flanges PIVOTING AUTOFEED SLIDE Single Pointing at plus or minus 20 PARTING SLIDE WITH MICROMETER Provides precise parting and beveling 6 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com

TRAV-L-CUTTER Pipe Saw The Wachs Trav-L-Cutter is a portable milling machine capable of cold cutting and beveling simultaneously on all machinable pipe materials, pipe schedules and pipe sizes from OD 6in - 72in (152.4-1829 mm). Mounted by its own tensioning chain, the Trav-L-Cutter drives itself around the pipe as it machines. For larger diameter pipe or vessels, simply add more drive chain sections. For greater accuracy specify the Trav-L-Cutter Guide Track. Available in pneumatic and hydraulic drive options. TRAV-L-CUTTER MODELS MODEL PIPE SIZE (in) PIPE SIZE (DN) Model E (Pneumatic) 6-72in DN 150-1800 MODEL HE (HYDRAULIC) Model HE (Hydraulic) 6-72in DN 150-1800 AVAILABLE BLADE TYPES MODEL E (PNEUMATIC) SLITTING BLADE BEVEL CUTTER & SLITTING SAW COMBINATION BEVEL CUTTER CHAIN ASSEMBLY & PINS Add more drive chain to the Trav-L-Cutter, increasing the effective operating diameter. Available in lengths ranging from 6-72in (DN150-1800). CHAIN ASSEMBLY & PINS GUIDE TRACK Install around the pipe circumference for precise, square cutting on vertical and / or large diameter pipes. Includes Trav-L-Cutter guide wheels for tracking. Available for 6in- 60in O.D. (ND150-1500) pipe sizes. GUIDE TRACK 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com 7

GUILLOTINE Pipe Saw GUILLOTINE SUPER C E.H. Wachs family of portable Guillotine pipe saws are designed to cold cut 2in - 32in (DN 50-800) pipe, as well as solids such as bar stock, rails and beams. Their compact design and easy setup make it the ideal saw for contractors, pipeline operations, refineries, petrochemical and processing plants and anywhere a fast, safe cut is needed. In use virtually everywhere, they re strong yet light, simple to mount, simple to operate and simply bulletproof. It s no wonder that when pipe saws are first mentioned, the Wachs Saw is mentioned first. GUILLOTINE MODELS MODEL PIPE SIZE (in) PIPE SIZE (DN) POWER OPTIONS Super C 2-12in DN 50-300 Electric, Air, Hydraulic Model D 6-18in DN 150-450 Air, Hydraulic Super D 10-24in DN 250-600 Air, Hydraulic Goliath 16-32in DN 400-800 Hydraulic GUILLOTINE MODEL D AVAILABLE BLADE TYPES MODEL GENERAL USE THIN WALL (3/16in MAX) HEAVY DUTY WALL CARBIDE TIPPED Super C 4 4 Model D 4 4 4 4 Super D 4 Goliath 4 4 SAW BLADES MODEL C HSS STANDARD BLADE For General Use GUILLOTINE SUPER D MODEL SUPER C STANDARD BLADE For General Use Carbon steel pipe, stainless steel and other high alloy materials MODEL SUPER C CARBIDE BLADE Cast, ductile and concretedlined pipe MODEL D HSS STANDARD BLADE Carbon steel pipe, stainless steel and other high alloy materials MODEL D CARBIDE BLADE Cast, ductile & concretedlined pipe MODEL SUPER D HEAVY DUTY BLADE Carbon steel pipe, stainless steel & other high alloy materials GOLIATH GUILLOTINE GOLIATH HEAVY DUTY BLADE For general use 8 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com

I.D. Mounted Machine Tools ½in 13mm 4in 102mm 8in 203mm 12in 305mm 16in 406mm 24in 610mm EP 424 END PREP EP 424 FORM TOOLING EP 424 SINGLE POINTING SDB 103 SDB SMALL DIAMETER BEVELER SDB 206 SDB 412 FF 206 FF FLANGE FACER FF 313 FF 424 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com 9

EP 424 Pipe End Prep The Wachs EP 424 with the patented new SpeedPrep feed system is a precision ID mount end prep machine tool designed to bevel, compound bevel, J prep, face and counterbore pipe, fittings and valves. Able to machine any bevel or compound bevel without templates, incline tool slides or work stoppage. The EP 424 is powerful enough to form tool from 4in - 14in (DN 100-350) and single point from 8in - 24in (DN 200-600) up to a 6.5in (165 mm) wall thickness. EP 424 SINGLE POINT MODEL EP 424 MODELS MODEL PIPE SIZE (in) PIPE SIZE (DN) Form Tool 4-16in DN 100-400 Single Point 8-24in DN 200-600 EP 424 TOOLING EP 424 FORM TOOL MODEL FACING TOOL INSERT HOLDER (HIGH RANGE) 30º BEVEL TOOL INSERT HOLDER KIT Cross section of EP 424 mounted for single pointing FORM TOOL INSERT HOLDER COUNTERBORE TOOL TAPER 4:1 PREMIUM GRADE HSS INSERT (2 SIDED) HOLDER KIT COUNTERBORE Faces flanges up to 24in (609.6mm) COUNTERBORE TOOL TAPER 4:1 10 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com

SDB Small Diameter Beveler E.H. Wachs SDB line of small diameter bevelers have been engineered for fast, precise onsite facing, beveling, compound beveling and counterboring of light and heavy wall pipe, tube or casing. Proven workhorses, they set up quickly with a self centering mandrel and chuck assembly mounting to the pipe I.D. Their highly productive design means one person can setup, operate and create a perfect weld prep in minutes. SDB BEVELER MODELS MODEL PIPE RANGE (in) PIPE RANGE (mm) 103/3 ID.875-4.5in OD ID 22.2-114 mm OD SDB 103 206/2 ID 1.91-6.625in OD ID 48.5-168mm OD 412/2 ID 3.80-12.02in OD ID 96.5-305.3mm OD SDB 103/3 PIPE END PREP BEVELER Face, bevel and counterbore simultaneously on carbon, stainless and high alloy steels. Machine boiler tubes, heavy wall pipe and thick wall tubing. Prep elbows and face flanges* using only one machine. Fast, accurate weld preps on pipe and tube from 0.875in I.D. through 4.5in O.D. (22.2 mm 114 mm) and flanges 2in I.D. (50.8 mm) through 6in O.D. (152.4 mm). Available in air or electric. SDB 206 SDB 206/2 PIPE END PREP BEVELER Bevel, counterbore, face and compound bevel pipe and tube from 1.91in I.D. through 6.625in O.D. (48.5 mm 168 mm) and face flanges* from 3in I.D. through 13in O.D. (76.2 mm 330.2 mm), regardless of material wall thickness. Only a 2.25in (57 mm) radial clearance is required. Available in air, electric or hydraulic. SDB 412/2 PIPE END PREP BEVELER Heavy-duty and compact. Designed to face, bevel, compound bevel and counter bore 3.80in I.D. through 12.02in O.D. (96.5 mm 305.3 mm) pipe or tube, up to 1.125in (29 mm) wall thickness and face flanges* 4in I.D. through 24in O.D (101.6 mm through 609.6 mm). Available in air, electric or hydraulic. SDB 412 SDB TO FF CONVERSION KIT: HEAD, MANDREL, LEGS, & FASTENERS FORM TOOL TO SINGLE POINT FF CONVERSION KIT 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com 11

FF Flange Facer Now anyone can produce a lathe quality surface finish on flat, raised or recessed face flanges in minutes. Based on the powerful Wachs SDB series ID mount end prep machines, the Wachs FF series flange facers offer a rugged yet lightweight and compact design that allows them to fit into tight quarters. With the addition of the SDB conversion kit, the FF models can be converted into SDB series machines, allowing them to face, bevel, compound bevel and counterbore. FF FLANGE FACER 206 FF FLANGE FACER MODELS MODEL FLANGE RANGE (in) FLANGE RANGE (mm) 206 ID 2-6in OD ID 50.8-152.4 mm OD 313 ID 3-13in OD ID 76.2-330.2mm OD 424 ID 4-24in OD ID 101.6-609.4mm OD FF 206 FLANGE FACER Cuts lathe quality surface finishes on flat and raised face flanges in minutes (Record Groove, RMS 500, 250, 125 & 63). These lightweight and compact machines setup quickly and convert to powerful beveling systems. Flanges 2in I.D. (50.8 mm) through 6in O.D. (152.4 mm). FF 313 FLANGE FACER Flange facing machine for facing raised and flat face flanges from 3in I.D. through 13in O.D. (76.2 mm I.D. through 330.2 mm O.D.). Single point heavy wall pipe 1in (25.4 mm) and greater. FF FLANGE FACER 313 FF 424 FLANGE FACER Flange facing machine for facing raised and flat face flanges from 4in I.D. through 24in O.D. (101.6 mm I.D. through 609.4 mm O.D.). Single point heavy wall pipe 1in (25.4 mm) and greater. SDB 103 / FF 206 MANDREL KIT SDB 206 / FF 313 MANDREL KIT FF FLANGE FACER 424 SDB 412 / FF 424 MANDREL KIT 12 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com

OTHER Products & Accessories RS-2 RISING STEM PORTABLE VALVE EXERCISER HANDHELD VALVE EXERCISERS The RS-2 Portable Valve Operator for rising and non-rising stem valves delivers up to 800 lb-ft torque (1085 Nm) and features new faster operating speeds for quick, reliable opening and closing of water, wastewater, pipeline and petrochemical valves. The RS-2 operates valves from 6in 60in (ND150-1500) and is available in hydraulic, pneumatic or electric drive. The P-2 handheld exerciser offers increased productivity, operator safety and valve protection. It s perfect for hard to reach valves, valve exercising and fast shut downs, delivering controlled power to operate valves 6in (ND600) and up. AIR CADDY AIR TREATMENT MODULE AIR TREATMENT & CONTROL Extremely portable, these pneumatic accessories condition and regulate the incoming air, and are simple to setup and easy to use at any job site. The Air Control Module (ACM) provides remote operation capability for select models of Wachs pneumatic powered machines, allowing operators to cut and bevel pipe up to 7.9 m (26 feet) away. This significantly reduces fatigue and allows operation from a safer distance, important in highly restricted or hazardous environments. EPM ELECTRIC POWER MOTOR POWER DRIVE & MOTOR OPTIONS E.H. Wachs offers a wide variety of power drive options including electric, hydraulic and pneumatic. For all of our quality machine tools a smooth, controllable power source is essential for precise weld prep, which is essential to a quality finished weld. Many Wachs machines can be operated with multiple drive types; others are designed for a single or specialized drive type. Whichever machine you rent, O.D. or I.D. mounted, E.H. Wachs has the optimum power solution for your application. EPD ELECTRIC POWER DRIVE & REMOTE CONTROL HYDRAULIC POWER UNITS Available in Gas, Diesel, or Electric, E.H. Wachs offers a wide variety of hydraulic power units to meet the needs of the project. Cart mount, trailer and skid-mounted power units are available in a variety of sizes and output ranges. E.H. Wachs stocks the equipment you need for the perfect prep. HPU HYDRAULIC POWER UNIT 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com 13

E.H. WACHS Rental Machines SDSF SMALL DIAMETER SPLIT FRAME R80-0000-AX Axial Feed SDSF 1in & 2in Kit Pneumatic R80-0000-RA Radial Feed SDSF 1in & 2in Kit Pneumatic R80-4000-10 SDSF 1.0 Split Frame R80-4000-20 SDSF 2.0 Split Frame R80-4000-30 SDSF 3.0 Split Frame R80-4000-40 SDSF 4.0 Split Frame LCSF LOW CLEARANCE SPLIT FRAME & ACCESSORIES R60-000-54 LCSF 204/3 Split Frame R60-000-56 LCSF 206/3 Split Frame R60-000-58 LCSF 408/3 Split Frame R60-000-60 LCSF 610/3 Split Frame R60-000-62 LCSF 612/3 Split Frame R60-000-64 LCSF 814/3 Split Frame R60-000-66 LCSF 1016/3 Split Frame R60-000-70 LCSF 1420/3 Split Frame R60-000-74 LCSF 1824/3 Split Frame R60-000-78 LCSF 2228/3 Split Frame R60-000-82 LCSF 2632/3 Split Frame R60-000-86 LCSF 3036/3 Split Frame R60-000-92 LCSF 3642/3 Split Frame R60-000-98 LCSF 4248/3 Split Frame R60-405-UC Universal Counterbore Slide R60-421-04 Low Clearance Slide Set For LCSF 204/3-1420/3 R60-422-01 Extended Slide Set for LCSF 204/3-1420/3 R60-428-12 Bridge Slide For LCSF 612/3 R60-428-14 Bridge Slide For LCSF 814/3 R60-428-16 Bridge Slide For LCSF 1016/3 R60-428-20 Bridge Slide For LCSF 1420/3 R60-428-24 Bridge Slide For LCSF 1824/3 R60-428-28 Bridge Slide For LCSF 2228/3 R60-428-32 Bridge Slide For LCSF 2632/3 R60-428-36 Bridge Slide For LCSF 3036/3 R60-428-42 Bridge Slide For LCSF 3642/3 R60-428-48 Bridge Slide For LCSF 4248/3 R60-440-00 Super Extended Slide Set for LCSF 1424/3-4248/3 R60-451-00 Out-of-Round Pipe Tracking Slide Set, LCSF 610/3-1420/3 R60-446-00 Out-of-Round Pipe Tracking Slide Set, LCSF 1824/3-4248/3 HDSF MACHINES & ACCESSORIES RP03-010-1224 12in-24in HDSF Split frame Hydraulic RP03-010-436 24in-36in HDSF Split frame Hydraulic RP03-010-448 36in-48in HDSF Split frame Hydraulic RP03-010-460 48in-60in HDSF Split frame Hydraulic RP03-010-472 60in-72in HDSF Split frame Hydraulic R60-446-00 Out-of-Round Pipe Tracking Slide Set, HDSF Series LDSF MACHINES & ACCESSORIES R12-042-5100-075 75in LDSF Split Frame³ R12-042-5100-090 90in LDSF Split Frame³ R12-042-5100-105 105in LDSF Split Frame³ R12-042-5100-120 120in LDSF Split Frame³ ³Includes spring-loaded parting & bevel slide, storage case, and manual Hydraulic Hydraulic Hydraulic Hydraulic TRAV-L-CUTTER R02-000-01 Trav-L-Cutter Model E Pneumatic R02-000-02 Trav-L-Cutter Model HE Hydraulic GUILLOTINE SAWS R03-000-01 Guillotine Saw Model C Electric 110V R03-000-02 Guillotine Saw Model C Pneumatic R03-000-03 Guillotine Saw Model C Hydraulic R04-000-01 Guillotine Saw Model D Electric 110V R04-000-02 Guillotine Saw Model D Pneumatic R04-000-03 Guillotine Saw Model D Hydraulic R24-000-01 Guillotine Saw Super C Electric 110V R24-000-02 Guillotine Saw Super C Pneumatic R24-000-03 Guillotine Saw Super C Hydraulic R25-000-01 Guillotine Saw Super D Pneumatic R25-000-03 Guillotine Saw Super D Hydraulic EP-424 END PREP R81-000-01 Form Tool EP 424, 4in-16in Pneumatic R81-000-02 Form Tool EP 424, 4in-16in Hydraulic R81-000-03 Single Point EP 424, 4in-24in Pneumatic R81-000-04 Single Point EP 424, 4in-24in Hydraulic SDB 103/3 BEVELER & FF 206 FLANGE FACER R16-000-01 SDB 103/3 Beveler Pneumatic R16-000-02 SDB 103/3 Beveler Electric 110V R16-000-FF FF 206 Flange Facer Pneumatic R16-401-00 SDB 103/3 Small Mandrel R16-404-00 SDB 103/3-FF 206 Single Point Slide R16-411-00 SDB 103/3 Pipe Collet Mandrel R16-412-00 SDB 103/3 Tube Collet Mandrel R16-414-00 SDB 103/3-FF 206 Short Perch Mandrel R16-421-00 SDB 103/3-FF 206 Flange Facer Conversion Kit SDB206/2 BEVELER & FF313 FLANGE FACER R56-000-01 SDB 206/2 Beveler Pneumatic R56-000-02 SDB 206/2 Beveler Electric 110V R56-000-FF FF 313 Flange Facer Pneumatic R56-302-00 Air Motor For SDB 206/2 & SDB 412/2 R56-402-01 Small Blade Mandrel for SDB 206/2 (1.91in-2.46in I.D.) R56-404-00 Single Point Slide for SDB 206/2 & FF 313 R56-407-01 8in Extender Kit for SDB 206/2 R56-411-01 SDB 206/2 Tube Collet Mandrel R56-412-01 SDB 206/2 Pipe Collet Mandrel R56-414-01 Short Perch Mandrel (3.00in-6.08in I.D.) R56-415-00 Extender Kit Short Perch Mandrel (6.00in-10.10in I.D.) R56-416-01 Small Short Perch Mandrel (2.00in-3.25in I.D.) R56-421-00 SDB 206-to-FF 313 Flange Facer Conversion Kit SDB 412/2 BEVELER & FF424 FLANGE FACER R66-000-01 SDB 412/2 Beveler Pneumatic R66-000-FF FF 424 Flange Facer Pneumatic R66-404-00 Single Point Slide R66-414-01 Short Perch Mandrel (3.75in-12.80in I.D.) R66-415-00 FF 424 Extender Kit For Short Perch Mandrel (12.72in-20.00in I.D.) R66-421-00 SDB 412/2-to-FF 424 Flange Facer Conversion Kit VALVE EXERCISERS R11-000-02 P-2 Valve Exerciser Electric 110V R11-000-03 P-2 Valve Exerciser Pneumatic R11-000-04 P-2 Valve Exerciser Hydraulic R11-000-05 P-2 Valve Exerciser Electric 220V R11-000-14 Vitals Ready P-2 Valve Exerciser Hydraulic R78-000-01 RS-2 Rising Stem Valve Exerciser Electric 110V R78-000-03 RS-2 Rising Stem Valve Exerciser Pneumatic R78-000-04 RS-2 Rising Stem Valve Exerciser Hydraulic AIR TREATMENT MODULE R26-407-00 Air Treatment Module R60-420-00 Split Frame Air Control Module PNEUMATIC & HYDRAULIC DRIVE MOTORS R60-4010-01 2.5 H.P Reversible Air Motor for EICC & Multi Axial Drill. R60-423-01 2-1/2 H.P. Air Motor R60-423-00 1-1/2 H.P. Air Motor R60-424-01 Hydraulic Drive HYDRAULIC POWER UNITS & HOSES R14-000-02 HCM-1G (8 GPM @ 1500 PSI) 4 Gas R14-000-06 HCM-2E2 (8GPM @ 1500 PSI) 4 Electric 220V R14-000-07 HCM-2E4 (8GPM @ 1500 PSI) 4 Electric 440V R14-000-08 HCM-2G Power Unit (10GPM @ 1500 PSI) 4 Gas R14-000-20 HPU-15 Hydrostatic Power Unit with 75ft Cable/ Pendant (0-15GPM variable pressure 1500-1800 PSI) 4 Electric 440V R14-000-25 HCM-3G Cart-Mounted HPU (14GPM @ 1500 PSI) 4 Gas R03-404-00 45ft, 1/2in Hydraulic Hose Set R02-408-00 45ft, 5/8in Hydraulic Hose Set for Trav-L-Cutter 4 Includes hose (R03-404-00) 14 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com

E.H. WACHS Genuine Wachs Tooling SDSF SPLIT FRAME TOOLING 52-701-01 Single Point Axial Tool² 52-701-01P Premium HSS 3/8in x 3/8in Tool Bit 52-701-02 Tool, Offset Dogleg, 3/8in x 3/8in x 1-1/2in, 1in ext.² 52-701-03 Tool, Offset Dogleg, 3/8in x 3/8in x 1-1/2in, 1-1/4in ext.² 52-703-02 Socket Weld Tool - Medium 52-705-01 30º Bevel Tool 52-705-03 45º Bevel Tool 52-710-02 37.5º Bevel Tool, 3/8 x 1/2 Med. 52-710-03 37.5º Bevel Tool, 3/8 x 1/2 Long. 52-711-01.094R Single Point Tool 52-711-02.125R Single Point Tool 52-711-03.188R Single Point Tool LCSF SPLIT FRAME TOOLING 43-702-05 30º X 3-1/8in Inside Bevel Tool 43-703-05 37-1/2º X 3-1/8in Inside Bevel Tool 43-704-02 Insert Extractor 43-707-05 30º Outside Bevel Tool, 3 1/8in Long 43-707-06 30º Outside Bevel Tool, 5in Long 43-708-05 37.5º Outside Bevel Tool, 3 1/8in Long 43-708-06 37.5º Outside Bevel Tool 5in Long 43-709-05 Double 30º Bevel Tool, 3 1/8in Long 43-709-06 Double 30º Bevel Tool, 5in Long 43-710-05 Double 37.5º Bevel Tool, 3 1/8in Long 43-710-06 Double 37.5º Bevel Tool X 5in Long 43-711-00 HSS Parting Blade., 3/16in x 3 7/16in Long 43-711-00P Premium HSS 3/16in Parting Blade (3 7/16in Long) 43-711-01 HSS Parting Tool, 3/16in x 5in Long 43-711-01P Premium HSS 3/16in Parting Blade (5in Long) 43-712-01 Inside 10 x 37-1/2º Bit, 4in Long 43-712-02 Outside 10 x 37-1/2º Bit, 4in Long 53-703-00 Beveling Tool, 37-1/2º, 5in Long 53-703-00P Premium HSS 37-1/2 Inside Bevel Tool (5in long) 53-703-01 30-Deg Inside Beveling Tool, 5in Long 53-703-01P Premium HSS 30 Inside Bevel Tool (5in long) 53-704-00 Inside 10 x 30 º Bit, 5in Long 53-705-00 Inside 10 x 37-1/2º Bit, 5in Long 60-711-00 HSS Parting Tool, 1/4in x 6in Long 60-711-00P Premium HSS 1/4in Parting Blade (6in Long) 60-712-00 Heavy Wall Carbide Tooling Kit 60-712-01 Heavy Wall Carbide Holder 60-712-02 Insert Extractor 60-712-03 Heavy Wall Insert Parting Kit¹ 60-712-04 Heavy Wall Carbide Holder¹ 60-713-00.313in Wide Insert² 60-713-01.313in Heavy Parting Insert¹² 60-714-00 1/4in Carbide Parting Tool Kit 60-714-01 1/4in Carbide Holder 60-715-00 1/4in Carbide Insert 60-716-00 3/16in Carbide Parting Tool Kit 60-716-01 3/16in Carbide Holder 60-717-00 3/16in Carbide Insert 60-718-00 Single Point Holder Kit 60-719-00 Bevel Tool, Inside 5in Long 45º 60-719-01 Bevel Tool, Inside 5in Long 60º 60-720-00 Bevel Tool, Outside - 5in Long 45º 60-720-01 Bevel Tool, Outside - 5in Long 60º TRAV-L-CUTTER TOOLING 02-601-00 6in X 3/16in HSS Slitting Saw For Up To 1in Wall 02-602-00 7in X 3/16in HSS Slitting Saw For Up To 1 1/2in Wall 02-603-00 7in X 9/32in HSS Slitting Saw, Use W/6in Bvl Cutters 02-604-00 8in X 3/16in HSS Slitting Saw For Up To 2 1/8in Wall 02-605-00 6in x 3/16in Carbide Tipped Saw For Cement Lined Pipe 02-606-00 7in x 3/16in Carbide Tipped Saw For Cement Lined Pipe 02-607-00 8in x 3/16in Carbide Tipped Saw For Cement Lined Pipe 02-608-LH L.H. Bevel 5in X 1/2in X 30º HSS Cutter 02-608-RH R.H. Bevel 5in X 1/2in X 30º HSS Cutter 02-609-LH L.H. Bevel 5in X 1/2in X 37.5º HSS Cutter 02-609-RH R.H. Bevel 5in X 1/2in X 37.5º HSS Cutter TRAV-L-CUTTER TOOLING 02-610-LH L.H. Bevel 6in X 3/4in X 30º HSS Cutter 02-610-RH R.H. Bevel 6in X 3/4in X 30º HSS Cutter 02-611-LH L.H. Bevel 6in X 3/4in X 37.5º HSS Cutter 02-611-RH R.H. Bevel 6in X 3/4in X 37.5º HSS Cutter GUILLOTINE TOOLING 04-402-00 Standard Model D Blade² 04-405-01 Carbide Model D Blade² 24-405-00 Standard Blade For Super C Guillotine² 24-405-01 Carbide Super C Blade² 25-402-00 Heavy Duty Blade (For Super D) SDB 103 TOOLING 26-410-02 Facing Tool 26-410-03 Facing Tool - Large 26-410-04 Facing Tool - Carbide Tip 26-411-01 37-1/2º Bevel Tool 1in I.D. 26-411-02 37-1/2º Bevel Tool 2in I.D. 26-411-03 37-1/2º Bevel Tool 3in I.D. 26-411-04 37-1/2º Bevel Tool, Carbide 26-412-01 Id Deburring Tool 26-412-02 Intermediate Deburring Tool 26-412-03 Id Deburring Tool - Large 26-426-00 30º Counterbore And Facing Tool 26-713-00 20º, 3/32in Radius "J" Tool SDB 206/412 & EP-424 TOOLING 56-708-01 Facing Short Holder Kit 56-708-02 Facing Long Holder Kit 56-709-01 20º Bevel Holder Kit 56-709-02 30º Bevel Holder Kit 56-709-03 37-1/2º Bevel Holder Kit 56-709-04 45º Bevel Holder Kit 56-709-05 20º Hi-Range Holder Kit 56-710-00 T-15 Tool Insert 56-710-01 SDB 37-1/2º Tool Set 56-711-01 HSS Tool Insert 56-711-02 HSS J-Prep Tool Insert 56-712-01 Carbide Tool Insert 56-712-02 Carbide J-Prep Tool Insert 56-713-00 4:1 Counterbore Tool 56-714-01 Carbide-Single Point Holder Kit 56-714-02 Flange Facing-High Range Holder Kit 56-714-03 Flange Facing-Low Range Holder Kit 56-715-00 Counterbore Holder Kit ¹ Optional ² Two Piece Minimum 600 KNIGHTSBRIDGE PARKWAY LINCOLNSHIRE, ILLINOIS 60069 T:+1.847.537.8800 F:+1.847.520.1147 SALES@EHWACHS.COM ehwachs.com 15

You YouTube.com/ehwachs TM Corporate Locations Sales Locations UNITED STATES ITW-OCW US Headquarters E.H. Wachs 600 Knightsbridge Parkway Lincolnshire, IL 60069 USA T: +1.847.537.8800 F: +1.847.520.1147 Toll Free: 800.323.8185 Contact your local ITW Orbital Cutting & Welding representative for additional information or to request a product demonstration. Gulf Coast Sales, Service & Rental Center E.H. Wachs 2220 South Philippe Avenue Gonzales, LA 70737 USA T: +1.225.644.7780 F: +1.225.644.7785 Houston North Sales, Service & Rental Center E.H. Wachs / Wachs Subsea 15331 Vantage Parkway East Houston, Texas 77032 USA T: +1.713.983.7198 F: +1.713.983.9752 Houston South Sales, Service & Rental Center E.H. Wachs 3414 Lilac Unit E Pasadena, Texas 77505 USA T: +1.713.983.0784 F: +1.713.983.0703 West Coast Sales, Service & Rental Center E.H. Wachs 5130 Fulton Drive, Unit J Fairfield, California 94534 USA T: +1.707.439.3763 F: +1.707.439.3766 East Coast Sales, Service & Rental Center E.H. Wachs 1001 Lower Landing Road, Suite 208 Blackwood, New Jersey 08012 USA T: +1.856.579.8747 F: +1.847.520.1147 GERMANY ITW-OCW Europe Headquarters Orbitalum Tools GmbH E.H. Wachs Sales & Service Center Josef-Schüttler-Straße 17 Singen D78224 Germany T: +49 (0) 77 31-792 0 F: +49 (0) 77 31-792 500 CANADA Wachs Canada Ltd Eastern Canada Sales, Service & Rental Center 1250 Journey s End Circle, Unit 5 Newmarket, Ontario L3Y 0B9 Canada T: +1.905.830.8888 F: +1.905.830.6050 Toll Free: 888.785.2000 Wachs Canada Ltd Western Canada Sales, Service & Rental Center 5411 82 Ave NW Edmonton, Alberta T6B 2J6 Canada T: +1.780.469.6402 F: +1.780.463.0654 Toll Free: 800.661.4235 UNITED KINGDOM Wachs UK UK Sales, Service & Rental Centre Units 4 & 5 Navigation Park Road One, Winsford Industrial Estate Winsford, Cheshire CW7 3RL United Kingdom T: +44 (0) 1606 861 423 F: +44 (0) 1606 556 364 UNITED ARAB EMIRATES Wachs Middle East & Africa Operations E.H. Wachs PO Box 262543 Jebel Ali Free Zone South Dubai FZS 5, ACO6 United Arab Emirates T: +00 971 4 88 65 211 F: +00 971 4 88 65 212 INDIA Wachs India E.H. Wachs / ITW India Private Limited Orbital Cutting & Welding Division 4A/19, IDA Phase-1 Medak District Telangana 502 319 India T: +91 40 3026 1812 F: +91 40 3048 0815 SINGAPORE Wachs Asia Pacific E.H. Wachs / ITW Welding Singapore 23 Tagore Lane #04-06/07 Tagore 23 Warehouse Singapore 787601 Singapore T: +(65) 9634 5432 F: +1 (847) 484 2692 CHINA Wachs China E.H. Wachs / ITW Welding China New Caohejing International Business Centre B-1501 No. 391 Guiping Road Shanghai 200052 China T: +86 (21) 52303751 F: +86 (21) 52303758 2015 RTL-001 1015