Perlok CR 1.2 Base Sheet Fastener Secure Base Sheets to Lightweight Insulating Concrete or Gypsum u Uses THE PERLOK CR 1.2 BASE SHEET FASTENER is a one piece unit, precision formed from G-90 galvanized steel, coated with CR. A Pogo Stick or wooden mallet should be used to install the fastener. This fastener is designed to secure base sheets to a minimum 1.25 thickness of poured lightweight insulating concrete or various gypsums. THE PERLOK CR 1.2 BASE SHEET FASTENER is Factory Mutual and Dade County approved. u THE PERLOK CR 1.2 BASE SHEET FASTENER is designed to secure base sheets to lightweight insulating concrete or various gypsums. u THE PERLOK CR 1.2 BASE SHEET FASTENER is F.M. and Dade County approved. u PERLOK CR 1.2 BASE SHEET FASTENER & Plate exceeds F.M. Class I-90 Wind Uplift requirements when installed in accordance with I-90 nailing pattern. u Assembled PERLOK CR 1.2 BASE SHEET FASTENER greatly reduces installation time and labor cost. u Entire fastener is CR coated to prevent in-place corrosion. A special corrosion resistant CR coating exhibits less than 15% red rust after 30 Kesternich cycles. CR is a unique epoxy based coating specifically applied to optimize resistance to corrosion. This special coating exceeds F.M. Approval Standard 4470. Lightweight insulating concrete or gypsum must be surface dry and reasonably smooth prior to roofing. For the best performance, the fastener should always be installed perpendicular to the substrate. Assembled PERLOK CR 1.2 BASE SHEET FASTENER is assembled with a GALVALUME 2.75 plate. Use the Pogo Stick to install the fastener. F.M. Approved For increased wind uplift resistance and high-wind applications, it is required that the PERLOK CR 1.2 BASE SHEET FASTENER with the PERLOK Base Sheet Plate be used in accordance with an approved I-90 nailing pattern. Note: On reroofing applications, prior to job start, roof should be inspected or tested to determine the pullout values. Physical Data Base Sheet Fastener: Head Size: 1.125 x 1 Leg : 1.2 Material Thickness:.014 nominal Material: G-90 galvanized with CR coating Plate: Diameter: 2.75 Material: GALVALUME Material Thickness:.014 nominal Packaging: Assembled: 1000 per carton Shipping Weight: 37 lbs. Standard: 1000 per carton Shipping Weight: 16 lbs. Plate: 1000 per carton Shipping Weight: 20 lbs. MSDS Available on Request at (800) 727-9872 or at www.derbigum.com.
Perlok CR 1.7 Base Sheet Fastener Secure Base Sheets to Lightweight Insulating Concrete or Gypsum u Uses THE PERLOK CR 1.7 BASE SHEET FASTENER is a one piece unit, precision formed from G-90 galvanized steel, coated with CR. A Pogo Stick or wooden mallet should be used to install the fastener. This fastener is designed to secure base sheets to a minimum 2 thickness of poured lightweight insulating concrete or various gypsums. THE PERLOK CR 1.7 BASE SHEET FASTENER is Factory Mutual and Dade County approved. u THE PERLOK CR 1.7 BASE SHEET FASTENER is designed to secure base sheets to lightweight insulating concrete or various gypsums. u THE PERLOK CR 1.7 BASE SHEET FASTENER is F.M. and Dade County approved. u PERLOK CR 1.7 BASE SHEET FASTENER & Plate exceeds F.M. Class I-150 Wind Uplift requirements when installed in accordance with FM requirements. u Assembled PERLOK CR 1.7 BASE SHEET FASTENER greatly reduces installation time and labor cost. u Assembled Base Sheet Fasteners are packaged for easy handling on the roof. u Entire fastener is CR coated to prevent in-place corrosion. A special corrosion resistant CR coating exhibits less than 15% red rust after 30 Kesternich cycles. CR is a unique epoxy based coating specifically applied to optimize resistance to corrosion. This special coating exceeds F.M. Approval Standard 4470. Lightweight insulating concrete or gypsum must be surface dry and reasonably smooth prior to roofing. For the best performance, the fastener should always be installed perpendicular to the substrate. Assembled PERLOK CR 1.7 BASE SHEET FASTENER is assembled with a GALVALUME 2.75 plate. Use the Pogo Stick to install the fastener. I-150 F.M. Approved The CR Base Sheet Fastener is FM approved to I-150 with certain base sheet and insulating concrete combinations. Note: Prior to job start, contact DERBIGUM Americas, Inc. to determine the correct nailing pattern. On reroofing applications, prior to job start, roof should be inspected or tested to determine the pullout values. Physical Data Base Sheet Fastener: Head Size: 1.125 x 1 Leg : 1.75 Material Thickness:.014 nominal Material: G-90 galvanized with CR coating Plate: Diameter: 2.75 Material: GALVALUME Material Thickness:.014 nominal Packaging: Assembled: 500 per carton Shipping Weight: 21 lbs. Standard: 1000 per carton Shipping Weight: 20 lbs. Plate: 1000 per carton Shipping Weight: 20 lbs. MSDS Available on Request at (800) 727-9872 or at www.derbigum.com.
Perlok Standard Roofing Fastener Designed to Secure Insulation and Roofing to Steel & Wood Decks u The PERLOK STANDARD ROOFING FASTENER is designed to secure insulation and roofing membrane to standard steel (18 ga. 24 ga.) and wood. It is available in lengths from 1 5/8 8. The PERLOK STANDARD ROOFING FASTENER is Factory Mutual and Dade County approved. Use with a PERLOK 3 steel plate. Uses u The PERLOK STANDARD ROOFING FASTENER is designed to secure insulation and roofing membrane to steel and wood decks. u Heavier shank & thread diameters than most standard roofing fasteners. u Deep buttress thread for high pullout resistance. u Extra sharp spade point for quick installation in new or reroof applications. u Available with hex head or #3 phillips truss head. A special corrosion resistant CR coating exhibits less than 15% red rust after 30 Kesternich cycles. CR is a unique epoxy based coating specifically applied to optimize resistance to corrosion. This special coating exceeds F.M. Approval Standard 4470. The PERLOK STANDARD ROOFING FASTENER must penetrate steel decks a minimum of 3/4, wood plank decks a minimum of 1 and 1/2 through the underside for plywood decks. Using a screwshooter, drive the fastener until a slight depression is seen around the plate, or with very rigid insulation boards, watch for the plate to dimple. Note: Care must be taken not to overdrive the fastener and fracture the skin of the insulation. Fastener must be tight enough so that the plate doesn t turn. For steel decks, Factory Mutual requires that the fastener penetrate the deck at the top fl ute. To speed installation, this fastener is also available as a labor saving preassembled screw and plate. See PERLOK Preassembled screw and 3 steel plate. Product Information The data below is constant for each PERLOK STANDARD ROOFING FASTENER. Thread Diameter:.220 Head Diameter: Truss Head:.435 Hex Head:.390 Head Style: #3 Phillips Truss Head* 1/4 Hex Head* : CR *#3 phillips bit or hex head drive included in each carton. MSDS Available on Request at (800) 727-9872 or at www.derbigum.com. Thread Packaging Weight 5 5 / 8 Full 1000 12 lb 2 1 / 4 Full 1000 16 lb 2 7 / 8 Full 1000 19 lb 3 1 / 4 3 1000 22 lb 3 3 / 4 3 100 25 lb 4 1 / 2 3 1000 29 lb 5 3 1000 35 lb 6 4 1000 42 lb 7 4 1000 48 lb 8 4 1000 54 lb
Perlok Dual Fastener Roof Insulation and Membrane Fastener for Base Ply, Recover Board and Insulation u PERLOK DUAL FASTENER is a roof insulation and membrane fastener for base ply, recover board and insulation to wood fiber or poured gypsum decks. u Composition: Factory pre-assembled components consisting of: TUBE: Precision formed from Galvanized (G-90) coated steel to prevent corrosion. The tube is shaped to easily penetrate decking and exiting membranes. DISK: Precision formed from Galvalume (AZ-55) coated steel to prevent corrosion. The disk is securely clamped to the tube, 2.7 diameter, rib reinforced to resist cupping. LOCKING STAPLE: Precision formed from high tensile steel wire. Physical Data Available s 1.4 1.8 2.8 3.8 4.8 Packaging 1.4, 1.8, 2.8, and 3.8 PERLOK DUAL FASTENER 500 per Carton 4.8 PERLOK DUAL FASTENER 250 per Carton MSDS Available on Request at (800) 727-9872 or at www.derbigum.com.
Installation Method u Drive fastener perpendicular to roof deck seating cap flash with roofing surface. Once tube is set, drive the locking staple thru the tube/disk unit into the deck until the top of the staple is flush with the cap (see illustration). The PERLOK DUAL FASTENER should always be embedded into the structural roof deck to a depth of at least 1. u Operation: When locking staple is driven, its dual wire legs diverge anchoring the fastener in place (see illustration on first page). Uplift resistance may vary depending on the density and integrity of the substrate. u Field Testing: On-site withdrawal testing should always be performed to evaluate the ability of the roofing substrate to satisfactorily accept and retain fasteners. Such testing may alter fastener selection and modify applicable fastening patterns. u Fastening Patterns: PERLOK DUAL FASTENER density and spacing vary depending on applicable uplift requirements. Local codes, governing Approval bodies, Derbigum membranes, and individual roof deck manufacturers all may have specific requirements that need to be addressed prior to beginning any roofing project. The following illustrates typical Factory Mutual recommended fastening patterns accepted by DERBIGUM Americas, Inc. and roof deck manufacturers. Fastening Guide for Base Sheets The following base ply attachment meets FM Class 1-60, 1-75 or 1-90 Windstorm Classification. DERBIGUM GP/XPS, Derbibase Ultra, Derbibase, PRS Glass Base Sheet, or Glass Ply IV/VI is fastened in the field of the roof with PERLOK DUAL FASTENER installed 9 on center in the side laps and 18 on center staggered in 2 rows, equally spaced, between the base ply side laps. Approximately 86 fasteners per square (100 ft. 2 ). Fastening Guide for Recovery Board and Insulation The following fastening attachment meets FM Class 1-90 Windstorm Classification. Approved insulation boards listed in FM Global Approval Guide or Roofnav for use with Derbigum roof systems is fastened with 8 Perlok Dual Fasteners per 4 x 4 board in a diamond in a box pattern. (1 fastener per 2 ft. 2 ).
Designed to Secure Insulation and Roofing to Steel & Wood Decks u The PERLOK HEAVY DUTY ROOFING FASTENER is designed to secure insulation and roofing membrane to heavy steel (18 ga. 20 ga.). It is available in lengths from 1 1/4-26. The PERLOK HEAVY DUTY ROOFING FASTENER is Factory Mutual and Dade County approved. Perlok Heavy Duty Roofing Fastner Uses u The PERLOK HEAVY DUTY ROOFING FASTENER is designed to secure insulation and roofing membrane to heavy steel and wood decks. u Heavier shank & thread diameters than most heavy duty roofing fasteners. u Deep thread for high pullout resistance. u Extra sharp spade point for quick installation in new or reroof applications. A special corrosion resistant CR coating exhibits less than 15% red rust after 30 Kesternich cycles. CR is a unique epoxy based coating specifi cally applied to optimize resistance to corrosion. This special coating exceeds F.M. Approval Standard 4470. The PERLOK HEAVY DUTY ROOFING FASTENER must penetrate the deck a minimum of 3/4. Using a screwshooter, drive the fastener until a slight depression is seen around the plate, or with very rigid insulation boards, watch for the plate to dimple. Note: Care must be taken not to overdrive the fastener and fracture the skin of the insulation. Fastener must be tight enough so that the plate doesn t turn. Use with a PERLOCK 3 steel plate. For best installation results, use a variable speed 0-2500 rpm screw gun. Product Information The data provided is constant for each PERLOK HEAVY DUTY ROOFING FASTENER. Thread Diameter:.245 Shank Diameter:.190 Head Diameter:.435 Head Style: : #3 Phillips Truss Head** CR **#3 phillips bit or hex head drive included in each carton MSDS Available on Request at (800) 727-9872 or at www.derbigum.com. Thread Packaging Weight 1 1 / 4 Full 1000 12 lb 1 3 / 4 Full 1000 16 lb 2 Full 1000 18 lb 3 Full 1000 26 lb 4 3 1000 34 lb 5 4 500 22 lb 6 4 500 26 lb 7 4 500 30 lb 8 4 500 34 lb 9 5 500 37 lb 10 5 500 40 lb 11 5 500 44 lb 12 5 250 25 lb 14 5 250 29 lb 16 5 250 37 lb Longer lengths upon request. Call DERBIGUM for information.
Designed to Secure Roofing Materials to Light Gauge Steel, Roof Decks Perlok Extra Heavy Duty Roofing Fastner u The PERLOK EXTRA HEAVY DUTY ROOFING FASTENER is a specialized, high performance fastener designed to secure roofing materials to certain light gauge steel. O.S.B., or aluminium roof decks. u Oversized heavy shank and thread diameters for enhanced pullout resistance in light gauge steel roof decks. u Deep buttress threads further increase pullout resistance. u Miniature drill point penetrates decks quickly and contributes to exceptional resistance to backout as well as pullout Perlok CR-10 corrosion resistant coating exhibits less than 15% red rust after 30 Kesternich cycles. CR-10 coating exceeds F.M. Approval Standards 4470. The PERLOK EXTRA HEAVY DUTY ROOFING FASTENER should always be tested on site by an Olympic representative to determine performance and proper installation procedure. Call Olympic to schedule testing. Plates & Accessories A variety of plates are available. Contact Perlok to determine the appropriate plate for your application. Product Information The data provided is constant for each PERLOK EXTRA HEAVY DUTY ROOFING FASTENER. Head Diameter:.435 Thread Diameter:.275 Head Style: : #3 Phillips Truss CR-10 MSDS Available on Request at (800) 727-9872 or at www.derbigum.com. Cat. No. Thread Packaging Weight EHD002 2 Full 1000 20 lb EHD003 3 Full 1000 29 lb EHD004 4 3 1000 38 lb EHD005 5 4 1000 47 lb EHD006 6 4 1000 56 lb EHD007 7 4 500 34 lb EHD008 8 4 500 38 lb EHD0010 10 4 500 47 lb EHD0012 12 4 500 56 lb EHD0014 14 4 500 32 lb EHD0016 16 4 500 38 lb
Perlok Polymer Gyptec Fastener Designed to Secure Insulation to Gypsum and Wood Decks u The PERLOK POLYMER GYPTEC FASTENER is a glass-filled nylon auger fastener with a 1-in head designed to secure insulation to gypsum and cementitious wood fiber. It is available in lengths from 2 1 / 2 12. The PERLOK POLYMER GYPTEC FASTENER is Factory Mutual and Miami Dade County approved. Use with a PERLOK 3 steel plates for insulation attachment. u Wide buttress thread design for high pullout resistance. u Non-penetrating design threads into the substrate but should not penetrate the deck. u Glass-filled nylon eliminates corrosion, thermal bridging, and condensation while yielding high tensile strength. The PERLOK POLYMER GYPTEC FASTENER must embed a minimum of 1 1 / 2 (2 is recommended, and required for FM applications) into the deck. The PERLOK POLYMER GYPTEC FASTENER can be installed into some cementitious wood decks without predrilling. A pilot hole is required for gypsum and must be a minimum of 1 / 2 deeper than embedment. Use a carbide tip drill bit or a 7 / 16, 1 / 2 or 9 / 16 drill bit as determined by pullout test results. It is recommended to install PERLOK POLYMER GYPTEC FASTENERs using a heavy duty variable speed screw gun at a low RPM. Note: Care must be taken not to overdrive the fastener and fracture the skin of the insulation. Fastener must be tight enough so that the plate does not turn. Prior to the job bid, contact DERBIGUM to perform a pullout test to determine drill bit size and the pullout values. Rev. 1/2012 Product Information The data below is constant for each PERLOK POLYMER GYPTEC FASTENER. Thread Diameter: 0.675 Head Diameter: 1.0 Head Style: Internal 1 / 4 Square Drive* : NA * 1 / 4 driver bit included in each carton. MSDS Available on Request at (800) 727-9872 or at www.derbigum.com. Thread Packaging Weight 2 1 / 2 1 1 / 2 500 13 lb 3 21 / 4 500 16 lb 3 1 / 2 2 1 / 4 500 18 lb 4 21 / 4 500 20 lb 4 1 / 2 2 1 / 4 500 22 lb 5 2 1 / 4 500 23 lb 5 1 / 2 2 1 / 4 500 24 lb 6 2 1 / 4 500 26 lb 6 1 / 2 2 1 / 4 500 28 lb 7 2 1 / 4 500 30 lb 7 1 / 2 2 1 / 4 500 32 lb 8 2 1 / 4 250 17 lb 8 1 / 2 2 1 / 4 250 19 lb 9 2 1 / 4 250 20 lb 9 1 / 2 2 1 / 4 250 21 lb 10 2 1 / 4 250 22 lb 10 1 / 2 2 1 / 4 250 23 lb 11 2 1 / 4 250 24 lb 11 1 / 2 2 1 / 4 250 25 lb 12 2 1 / 4 250 26 lb