www.snxtechnologies.com Page 1 SNX / VITAP Eclipse Semi-Automatic Contour Edgebander (Laser & Heavy Duty Vacuum Arm) SNX Technologies is pleased to provide the following quote New Vitap Eclipse Contour EdgeBander Customer Information: Primeway Inc 555 East Mandoline Ave Madison Heights, MI 48071 Contact: Mr. Kevin Walby Phone: (248) 583-6922 Email: kevin@primewayinc.com Quote #2080-13 / October 29 2013
www.snxtechnologies.com Page 2 Eclipse Semi-Automatic Contour Edgebander Benefits of the Eclipse Contour Edgebander with Laser & Heavy Duty Vacuum arm & Infeed drive rollers Efficient design using latest engineering and manufacturing techniques Heavy duty Frame construction Large Heavy Duty movable vacuum pod arm for ease of operation (max panel weight 165lbs) State-of-the-art electronic control systems and High Frequency motors Laser measurement to help insure constant tight splice-joints on closed panels. Designed to apply hot melt EVA Adhesive and edgebanding (Note: 0.5 to 3mm edgeband thickness) Trimming unit will facilitate trimming of the top and bottom overhang of the edgebanding (NOTE: 0.5mm /.020 thin tape is QUALITY & ADHESIVE temperature dependent. Always best to operate with thicker tapes) BASIC MACHINE CONFIGURATION: NEW LARGER DIGITAL TOUCH SCREEN CONTROL (7 screen) Ability to program length / Electronic Encoder, cut-off point for guillotine.(edgeband Cut-off) Ability to select Laser measurement to assist encoder for more accurate splicing of joints. NEW Adjustable LASER POSITIONING (Side to Side adjustment) Temperature On / Off (and separate temperature thermostat to adjust adhesive temperatures) + & - adjustment for a more accurate splicing / timing of the guillotine cut-off timing. Screen with graphic interface makes programming easy. Ability to select MANUAL or SEMI-AUTOMATIC function of the machine functions NEW Variable Speed Manual adjustment
www.snxtechnologies.com Page 3 Eclipse Semi-Automatic Contour Edgebander, continued... WORK PIECE HOLDING MECHANISM Utilizes a pneumatic vacuum pump system (adjustable via pneumatic regulator) Vacuum is provided to via a rotating vacuum pod table (Includes Round & Rectangle Pods) Additional vacuum tables can be made easily by the customer. (greater panel support) Vacuum table has a rubber gasket to ensure adequate work piece hold. Work piece feeder is motorized with EXTRA WIDE rubber Roller and Double lower support Rollers Vacuum table is at the end of a large, Heavy Duty articulating arm.(max panel weight of 165 Lbs) Max. Workpiece size is: 200mm to 2400mm max. (within the circumference) EDGE COIL MAGAZINE One (1) universal magazine rotating table for coiled material. Automatic guillotine for coiled material up to 3 mm. x 45 mm (Encoder & Laser counter included ) Guillotine is activated by a Digital / Laser encoder reader for edgebanding of complete (closed) work pieces for a joint / splice of the ends of the tape, or by manual foot pedal when the piece is only with one side contoured. Guillotine, Tape guide & Power feeder system Digital Encoder / Reader LASER measurement GLUING STATION Equipped with a glue pot with 1kg. capacity
www.snxtechnologies.com Page 4 Utilizes 2x800w heating elements with electronic temperature control via Digital control. Glue is applied to Edge tape by means of a glue roller. 10-60mm work piece thickness. (Note: Work piece thickness is dependent upon edge tape thickness) Glue tank made from aluminum for easy heat dissipation and cleaning Glue spread thickness amount is adjusted via a manual knob. Digital glue temperature settings Dual rollers to copy the shape / contour of the parts being edgebanded TOP & BOTTOM TRIM STATION: COMBINATION / CHAMFER & RADIUS TRIM UNIT Two high frequency motors for edge trimming Motor: 2 x 0.5 KW (.75 HP), 300 HZ, Speed 12000 RPM.. Vertical and Horizontal tracing via ball-bearing copy rollers and pad. Maximum edgestrip thickness: 3 mm (up to 45 mm panel thickness) Maximum edgestrip height: 60mm Radius capability up to 3 mm radius. Manual adjustment of the trim motors for work piece thickness via hand lever. Pneumatic opening of the trim motors to facilitate the introduction of the panel Guiding and positioning of trimming function around the contour of the work piece is done manually by the operator. Pneumatic Exclusion of the Trim unit via auto switch. (Out of work area and back into work area) 2 Brazed cutters heads with 3mm Radius to chamfer 15 degree finish (D=69 / min.60 / Z=6) On / Off selector switch for independent use of unit
www.snxtechnologies.com Page 5 MACHINE TECHNICAL DATA: Machine Dimensions: 2100 x 1600 x 1600 Dust extraction port: 1 port at 80mm for Trimming unit Working Dimensions: Edge Coil Thickness: 0.5mm /.020-3mm (0.5 or thicker thin tape ONLY with proper Low Temp Adhesive) Work piece min : Diam.200 mm Work piece max 2400 x 2400mm Work piece Thickness: 10-60mm Edgeband Thickness 0.5mm /.020 to 1 mm for panels up to 60mm thick 2 mm for panels up to 60 mm thick 3 mm for panels up to 45mm thick Minimum Outside Radius Minimum Inside Radius Feed (Rotation) Speed: Air Requirement: 30 mm (note: based on 1mm thickness of edge tape) 250 mm 5 m/min 6 bar (90 psi) IMPORTANT NOTE: All above Working Dimensions are as a General Rule and are application / Quality of materials and Adhesive temperature dependent. (Could change with SEMI-RIGID PVC TAPES) Minimum internal radius ; min R = 250 mm Part Size: min. ø = 200 mm Max. ø = 2400 mm Panel Thickness: Panel thickness 10-60 mm with edge thickness 1 mm Panel thickness 10-60 mm with edge thickness 2 mm Panel thickness 10-45 mm with edge thickness 3 mm R Edge thickness 1 mm, min = R 30 mm Edge thickness 2 mm, min = R 50 mm Edge thickness 3 mm, min = R 80 mm Note: Radius could possibly increase or decrease depending on Adhesive Temperature and quality of edge tape; Semi or Rigid. Tape Height: min 12 mm Max 64 mm