MSP5.A Surface Mount TRANSZORB Transient Voltage Suppressors esmp TM Series Top View Bottom View MicroSMP PRIMARY CHARACTERISTICS V WM 5. V P PPM W I FSM 25 A T J max. 5 C FEATURES Very low profile - typical height of.65 mm Ideal for automated placement Oxide planar chip junction Uni-directional polarity only Peak pulse power: W (/ µs) ESD capability: 5 kv (air), 8 kv (contact) Meets MSL level, per J-STD-2C, LF maximum peak of 26 C Solder dip 265 C max. s, per JESD 22-A AEC-Q qualified Compliant to RoHS directive 22/95/EC and in accordance to WEEE 22/96/EC Halogen-free according to IEC 6249-2-2 definition Find out more about Vishay s Automotive Grade Product requirements at: /applications TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units specifically for protecting 5. V supplied sensitive equipment against transient overvoltages. MECHANICAL DATA Case: MicroSMP Molding compound meets UL 94 V- flammability rating Base P/N-M3 - halogen-free and RoHS compliant, commercial grade Base P/NHM3 - halogen-free and RoHS compliant, automotive grade Terminals: Matte tin plated leads, solderable per J-STD-2 and JESD 22-B2 M3 suffix meets JESD 2 class A whisker test, HM3 suffix meets JESD 2 class 2 whisker test Polarity: Color band denotes the cathode end RATINGS (T A = 25 C unless otherwise noted) PARAMETER SYMBOL VALUE UNIT Peak pulse power dissipation ()(2) P PPM W Peak pulse current with a / µs waveform (fig. ) I PPM.9 A Non repetitive peak forward surge current ms single half sine-wave (2) I FSM 25 A Power dissipation T L = 2 C (2) P D. W Operating junction and storage temperature range T J, T STG - 55 to + 5 C () Non-repetitive current pulse, per fig. (2) Mounted on 6. mm x 6. mm copper pads to each terminal Revision: 6-Jun-9
MSP5.A ELECTRICAL CHARACTERISTICS (T A = 25 C unless otherwise noted) DEVICE TYPE DEVICE MARKING CODE BREAKDOWN VOLTAGE V BR AT I () T (V) MIN. MAX. TEST CURRENT I T (ma) () Pulse test: t p 5 ms (2) Surge current waveform per Fig. and derate per Fig. 2 STAND-OFF VOLTAGE V WM (V) REVERSE LEAKAGE AT V WM I D (µa) CLAMPING VOLTAGE (2) V C (V) AT I PPM (A) / µs CLAMPING VOLTAGE (2) V C (V) AT I PPM (A) 8/2 µs MSP5.A AE 6.4 7.7 5. 9.2.9 4.5 57 THERMAL CHARACTERISTICS (T A = 25 C unless otherwise noted) PARAMETER SYMBOL VALUE UNIT Typical thermal resistance () R θja 25 C/W R θjl 3 Note () Thermal resistance from junction to ambient and junction to lead mounted on P.C.B. with 6. mm x 6. mm copper pad areas. R θjl is measured at the terminal of cathode band. IMMUNITY TO STATIC ELECTRICAL DISCHARGE TO THE FOLLOWING STANDARDS (T A = 25 C unless otherwise noted) STANDARD TEST TYPE TEST CONDITIONS SYMBOL CLASS VALUE AEC-Q- Human body model (contact mode) C = pf, R =.5 kω H3B > 8 kv V C IEC-6-4-2 (2) Human body model (air discharge mode) () C = 5 pf, R = 5 Ω 4 > 5 kv () Immunity to IEC-6-4-2 air discharge mode has a typical performance > 3 kv (2) System ESD standard ORDERING INFORMATION (Example) PREFERRED P/N UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE MSP5.A-E3/89A.6 89A 45 7" diameter plastic tape and reel MSP5.AHE3/89A ().6 89A 45 7" diameter plastic tape and reel MSP5.A-M3/89A.6 89A 45 7" diameter plastic tape and reel MSP5.AHM3/89A ().6 89A 45 7" diameter plastic tape and reel Note () Automotive grade 2 Revision: 6-Jun-9
P PPM - Peak Pulse Power (kw) Transient Thermal Impedance ( C/W) MSP5.A RATINGS AND CHARACTERISTICS CURVES (T A = 25 C unless otherwise noted) I PPM - Peak Pulse Current, % I RSM 5 5 t r = µs t r = 8 µs Peak Value I PPM Half Value - I PPM T J = 25 C Pulse Width (t d ) is defined as the Point where the Peak Current decays to 5 % of I PPM I PP 2 t d = µs t d = 2 µs Peak Forward Current (A) T J = 5 C T J = 25 C t d. 2. 3. 4. t - Time (ms)..4.6.8..2.4.6 V F - Forward Voltage Drop (V) Figure. Pulse Waveform Figure 4. Typical Peak Forward Voltage Drop vs. Peak Forward Current 8. C J - Junction Capacitance (pf) 7 6 5 4 3.. t d - Pulse Width (µs) Figure 2. Peak Pulse Power Rating Curve 2 2 3 4 Reverse Voltage (V) Figure 5. Typical Junction Capacitance 4 Reverse Leakage Current (µa) 3 2 25 5 75 25 5 T J - Junction Temperature ( C) Figure 3. Relative Variation of Leakage Current vs. Junction Temperature.. t - Pulse Duration (s) Figure 6. Typical Transient Thermal Impedance Revision: 6-Jun-9 3
MSP5.A PACKAGE OUTLINE DIMENSIONS in inches (millimeters) MicroSMP Cathode Band.59 (.5).43 (.).3 (.75).22 (.55).55 (.4).47 (.2).39 (.98).3 (.78).3 (.75).22 (.55).9 (2.3).83 (2.).6 (2.7).9 (2.3) Mounting Pad Layout.79 (2.).32 (.8).29 (.73).25 (.63).43 (.).32 (.8). (.27).5 (.2).2 (.5) 4 Revision: 6-Jun-9
Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 9 Revision: 8-Jul-8