Power Schottky rectifier Features Datasheet - production data A K SMA STPS2H100A Table 1. Device summary Symbol A K SMB STPS2H100U K Value A SMAflat STPS2H100AF A K SMBflat STPS2H100UF Negligible switching losses High junction temperature capability Low leakage current Good trade-off between leakage current and forward voltage drop Avalanche capability specified Description Schottky rectifiers designed for high frequency miniature switched mode power supplies such as adapters and on board DC/DC converters. Available in SMA, low-profile SMA, SMB, lowprofile SMB. I F(AV) 2 A V RRM 100 V T j (max) 175 C V F (max) 5 V June 2013 DocID6115 Rev 8 1/12 This is information on a product in full production. www.st.com
Characteristics STPS2H100 1 Characteristics Table 2. Absolute ratings (limiting values -T amb = 25 C unless otherwise stated) Symbol Parameter Value Unit V RRM Repetitive peak reverse voltage 100 V SMA / SMB T L = 130 C = 0.5 I F(AV) Average forward current SMAflat T L = 145 C = 0.5 2 A SMBflat T L = 150 C = 0.5 I FSM Surge non repetitive forward current t p =10 ms sinusoidal 75 A P ARM Repetitive peak avalanche power t p = 1 µs T j = 25 C 2400 W T stg Storage temperature range -65 to + 175 C T j Maximum operating junction temperature (1) 175 C 1. dptot 1 < condition to avoid thermal runaway for a diode on its own heatsink dtj Rth(j-a) Table 3. Thermal resistance Symbol Parameter Value Unit SMA 30 R th(j-l) Junction to lead SMAflat 20 SMB 25 C/W SMBflat 15 Table 4. Static electrical characteristics Symbol Parameter Test conditions Min. Typ. Max. Unit I R (1) V F (2) Reverse leakage current Forward voltage drop T j = 25 C 1 µa V R = V RRM T j = 125 C 1 ma T j = 25 C 0.79 I F = 2 A T j = 125 C 5 T j = 25 C 8 I F = 4 A T j = 125 C 9 0.74 V 1. Pulse test: t p = 5 ms, < 2% 2. Pulse test: t p = 380 µs, < 2% To evaluate the conduction losses use the following equation: P = 0.56 x I F(AV) + 45 I 2 F (RMS) 2/12 DocID6115 Rev 8
Characteristics Figure 1. Average forward power dissipation versus average forward current 1.7 1.6 1.5 1.3 1.2 1.1 0.9 0.7 0.5 0.3 0.1 P F(AV) (W) δ = 5 δ = 0.1 I F(AV) (A) δ = δ = 0.5 δ=tp/t δ = 1 1.2 1.6 1.8 2.0 2.2 T tp Figure 2. Average forward current versus ambient temperature ( = 0.5) (SMA / SMB) 2.2 2.0 1.8 1.6 1.2 I F(AV) (A) δ=tp/t SMA R th(j-a) =100 C/W S (CU) =1.5cm2 T tp R th(j-a) =Rth(j-I) SMB R th(j-a) =80 C/W S (CU) =1.5cm2 T amb( C) 0 25 50 75 100 125 150 175 SMA SMB 2.2 2.0 1.8 1.6 1.2 Figure 3. Average forward current versus ambient temperature ( = 0.5) (SMBflat) I F(AV) (A) T R th(j-a) =Rth(j-l) δ=tp/t tp T amb( C) SMBflat R th(j-a) =40 C/W 2. S CU=2.5 cm 0 25 50 75 100 125 150 175 Figure 5. Normalized avalanche power derating versus pulse duration Figure 4. Average forward current versus ambient temperature ( = 0.5) (SMAflat) I F(AV) (A) 2.2 2.0 1.8 1.6 1.2 T R th(j-a) =R th(j-l) δ=tp/t tp T amb( C) SMAflat 0 25 50 75 100 125 150 175 Figure 6. Normalized avalanche power derating versus junction temperature 1 P ARM(tp) P ARM(1 µs) 1.2 P ARM(Tj) P ARM(25 C) 1 0.1 1 01 1 0.1 1 t (µs) p 10 100 1000 0 T ( C) j 25 50 75 100 125 150 DocID6115 Rev 8 3/12 12
Characteristics STPS2H100 Figure 7. Relative variation of thermal impedance junction to ambient versus pulse duration (SMA) 0.9 0.7 0.5 0.3 0.1 Z th(j-a) /Rth(j-a) SMA Single pulse t (s) p 1.E-02 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03 Figure 8. Relative variation of thermal impedance junction to lead versus pulse duration (SMAflat) 0.9 0.7 0.5 0.3 0.1 Z th(j-l) /Rth(j-l) SMAflat Single pulse t (s) p 1.E-04 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01 Figure 9. Relative variation of thermal impedance junction to ambient versus pulse duration (SMB) 0.9 0.7 0.5 0.3 0.1 Z th(j-a) /Rth(j-a) SMB Single pulse t (s) p 1.E-02 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03 Figure 10. Relative variation of thermal impedance junction to lead versus pulse duration (SMBflat) 0.9 0.7 0.5 0.3 0.1 Z th(j-l) /Rth(j-l) SMBflat Single pulse t (s) p 1.E-04 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01 Figure 11. Reverse leakage current versus reverse voltage applied (typical values) 1.E+04 I (µa) R Figure 12. Junction capacitance versus reverse voltage applied (typical values) 100 C(pF) 1.E+03 1.E+02 1.E+01 T j =150 C T j =125 C T j =100 C T j =75 C F=1MHz V OSC=30mVRMS T j=25 C 1.E+00 T j =50 C 1.E-01 1.E-02 T j =25 C V (V) R 0 20 40 60 80 100 10 V (V) R 1 10 100 4/12 DocID6115 Rev 8
Characteristics Figure 13. Forward voltage drop versus forward current (low level) I FM(A) 2.0 Figure 14. Forward voltage drop versus forward current (high level) I FM(A) 100 1.8 1.6 T j =125 C (Maximum values) T j =125 C (Maximum values) 1.2 T j=125 C (Typical values) 10 T j=125 C (Typical values) T j=25 C (Maximum values) V FM(V) 0.1 0.3 0.5 0.7 0.9 1.1 1.2 T j=25 C (Maximum values) V FM(V) 1 0.5 0.7 0.9 1.1 1.2 1.3 1.5 1.6 1.7 1.8 Figure 15. Thermal resistance junction to ambient versus copper surface under each lead (SMA) 130 120 110 100 90 80 70 60 50 40 30 20 10 0 R th(j-a) ( C/W) Epoxy printed circuit board FR4, Copper thickness = 35 µm S CU(cm²) 0.5 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Figure 17. Thermal resistance junction to ambient versus copper surface under each lead (SMB) R th(j-a) ( C/W) 110 100 90 80 70 60 50 40 30 20 10 0 Epoxy printed circuit board FR4, Copper thickness = 35 µm S CU(cm²) 0.5 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 SMA SMB Figure 16. Thermal resistance junction to ambient versus copper surface under each lead (SMAflat) R th(j-a) ( C/W) 200 180 160 140 120 100 80 60 40 20 0 Epoxy printed circuit board FR4, Copper thickness = 35 µm SMAflat S CU(cm²) 0.5 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Figure 18. Thermal resistance junction to ambient versus copper surface under each lead (SMBflat) 110 100 90 80 70 60 50 40 30 20 10 0 R th(j-a) ( C/W) Epoxy printed circuit board FR4, Copper thickness = 35 µm SMBflat S CU(cm²) 0.5 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 DocID6115 Rev 8 5/12 12
Package information STPS2H100 2 Package information Epoxy meets UL94, V0 Lead-free packages In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Figure 19. SMA dimension definitions E1 D E A1 C L A2 b Ref. Table 5. SMA dimension values Millimeters Dimensions Inches Min. Max. Min. Max. A1 1.90 2.45 75 94 A2 5 0 02 08 b 1.25 1.65 49 65 c 0.15 0 06 16 D 2.25 2.90 89 0.114 E 4.80 5.35 0.189 11 E1 3.95 4.60 0.156 0.181 L 0.75 1.50 30 59 6/12 DocID6115 Rev 8
Package information Figure 20. SMA footprint (dimensions in mm) 2.63 1.64 5.43 Figure 21. SMB dimension definitions E1 D E A1 C A2 L b Ref. Table 6. SMB dimension values Millimeters Dimensions Inches Min. Max. Min. Max. A1 1.90 2.45 75 96 A2 5 0 02 08 b 1.95 2.20 77 87 c 0.15 0 06 16 E 5.10 5.60 01 20 E1 4.05 4.60 0.159 0.181 D 3.30 3.95 0.130 0.156 L 0.75 1.50 30 59 DocID6115 Rev 8 7/12 12
Package information STPS2H100 Figure 22. SMB footprint (dimensions in mm) 1.62 2.60 1.62 2.18 5.84 Figure 23. SMAflat dimension definitions D A c E E1 L 2x L1 2x b L L2 2x Ref. Table 7. SMAflat dimensions Millimeters Dimensions Inches Min. Typ. Max. Min. Typ. Max. A 0.90 1.10 35 43 b 1.25 1.65 49 65 c 0.15 0 06 16 D 2.25 2.95 88 0.116 E 4.80 5.60 0.189 20 E1 3.95 4.60 0.156 0.181 L 0.75 1.50 30 59 L1 0.50 19 L2 0.50 19 8/12 DocID6115 Rev 8
Package information Figure 24. SMAflat footprint dimensions 5.52 (17) 1.52 (60) 1.20 (47) 3.12 (0.123) millimeters (inches) 1.20 (47) Figure 25. SMBflat dimension definitions D A c L L2 E E1 b L L1 Ref. Millimeters Table 8. SMBflat dimensions Dimensions Inches Min. Typ. Max. Min. Typ. Max. A 0.90 1.10 35 43 b (1) 1.95 2.20 77 87 c (1) 0.15 0 06 16 D 3.30 3.95 0.130 0.156 E 5.10 5.60 00 20 E1 4.05 4.60 0.189 0.181 L 0.75 1.50 29 59 L1 0 16 L2 0 24 1. Applies to plated leads DocID6115 Rev 8 9/12 12
Package information STPS2H100 Figure 26. SMBflat footprint (dimensions in mm) 5.84 2.07 1.20 3.44 1.20 10/12 DocID6115 Rev 8
Ordering information 3 Ordering information Table 9. Ordering information Order code Marking Package Weight Base qty Delivery mode STPS2H100A S21 SMA 68 g 5000 Tape and reel STPS2H100AF F21 SMAflat 35 g 10000 Tape and reel STPS2H100U G21 SMB 0.107 g 2500 Tape and reel STPS2H100UF FG21 SMBflat 50 g 5000 Tape and reel 4 Revision history Table 10. Document revision history Date Revision Changes Jul-2003 4A Last update. Aug-2004 5 08-Feb-2007 6 SMA package dimensions update. Reference A1 max. changed from 2.70 (0.106 inches) to 2.03 mm (80 inches). Reformatted to current standards. Added ECOPACK statement. Added SMBflat package. 15-Feb-2010 7 Updated weight for SMBflat in Table 9. 24-Jun-2013 8 Added SMAflat package DocID6115 Rev 8 11/12 12
Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 12/12 DocID6115 Rev 8