Surface Mount Fasteners Revised 98
SURFACE MOUNT FASTENERS PEM ReelFast surface mount nuts, spacers, panel fasteners and R ANGLE fasteners are mounted to printed circuit boards in the same manner as other surface mount components prior to the solder reflow process. The fasteners are provided on tape and reel compatible with existing SMT automated installation equipment. Nuts and spacers are available in threaded and unthreaded sizes. Benefits of ReelFast SMT fasteners are: Faster assembly Reduced scrap Reduced handling Reduced risk of board damage that may occur when fasteners are improperly installed with off-line equipment Reduced loose hardware ReelFast SMT fasteners are recommended for reflow soldering designs. Contact our Applications Engineering Department for wave soldering solutions. SMT-2 Copyright 24 PennEngineering.
TYPE SMTSO ReelFast SMT SPACERS/NUTS Look for the two groove trademark. Stencil Masking Examples C ØD Solder Pad E A L ØH Plated through hole not required. Thru Thread or Length L ±.5 Min. ØH Hole Size ØD Thread Hole Thru Hole (Length code in 32nds of an inch) Sheet A C E In Sheet Min. Solder Size +.4.3 Type.62.125.25.375 Thickness Max. Max. ±.5 +.3. Pad.86-56 (#2-56) SMTSO 256 2 4 8 12.6.6.142.219.147.244.112-4 (#4-4) SMTSO 44 2 4 8 12.6.6.161.219.166.244.138-32 (#6-32) SMTSO 632 2 4 8 12.6.6.28.281.213.36.164-32 (#8-32) SMTSO 832 2 4 8 12.6.6.245.344.25.369.116 SMTSO 116 2 4 8 12.6.6.161.219.166.244.143 SMTSO 143 2 4 8 12.6.6.28.281.213.36 Thread Thru Thread or Min. ØH Hole Size ØD Length L ±.13 Size x Hole Thru Hole Sheet A C E In Sheet Min. Solder (Length code in millimeters) Pitch +.1.8 Type Thickness Max. Max. ±.13 +.8 Pad M2 x.4 SMTSO M2 2 3 4 6 8 1 1.53 1.53 3.6 5.56 3.73 6.2 M2.5 x.45 SMTSO M25 2 3 4 6 8 1 1.53 1.53 4.9 5.56 4.22 6.2 M3 x.5 SMTSO M3 2 3 4 6 8 1 1.53 1.53 4.9 5.56 4.22 6.2 M3.5 x.6 SMTSO M35 2 3 4 6 8 1 1.53 1.53 5.28 7.14 5.41 7.77 M4 x.7 SMTSO M4 2 3 4 6 8 1 1.53 1.53 6.22 8.74 6.35 9.37 3.6 SMTSO 3.6 2 3 4 6 8 1 1.53 1.53 5.28 7.14 5.41 7.77 4.2 SMTSO 4.2 2 3 4 6 8 1 1.53 1.53 6.22 8.74 6.35 9.37 Number Of Parts Per Reel / Pitch (mm) For Each Size Thread/Thru-Hole Length Size 2 3 4 6 8 1 12 256, 44, 632, 116, 143 15 / 12 1 / 12 65 / 12 3 / 16 832 11 / 16 8 / 16 5 / 16 3 / 16 M2, M25, M3, M35, 3.6 15 / 12 1 / 12 9 / 12 65 / 12 375 / 16 3 / 16 M4, 4.2 11 / 16 8 / 16 675 / 16 5 / 16 375 / 16 3 / 16 Part Number Designation SMTSO - 44 Type Thread or Thru Hole - 2 Length ET Finish Packaged on 13 recyclable reels. Tape width is 24mm. Supplied with Kapton patch for vacuum pick up. Reels conform to EIA-481. MATERIAL: Carbon Steel. STANDARD FINISH: ET - Electro Plated Bright Tin, ASTM B 545, Class A W/ Clear Preservative Coating. OPTIONAL FINISH: DT - Matte Electro-Tin ASTM B 545, Class A W/ Clear Preservative Coating, Annealed. THREADS: Internal, ANSI B1.1 2B ANSI/ASME B1.13M, 6H SMT-3
PANEL FASTENER COMPONENTS AND ASSEMBLY DATA RETAINER Packaged on 13 recyclable reels of 465 pieces. Tape width is 24mm. Supplied with Kapton patch for vacuum pick up. Reels conform to EIA-481. Stencil Masking Examples A R E Part Number Designation For Retainer C B ØD Solder Pad Plated through hole not required. SMTPR - 6 Type Retainer Size - 1 Shank ET Finish ØH A ØH ØD Retainer Part (Shank) Min. Sheet B C E R Hole Size In Sheet Min. Solder Number Max. Thickness ±.3 Max. Nom. ±.5 +.3. Pad SMTPR-6-1.6.6.167.249.375.325.25.396 A ØH ØD Retainer Part (Shank) Min. Sheet B C E R Hole Size In Sheet Min. Solder Number Max. Thickness ±.8 Max. Nom. ±.13 +.8 Pad SMTPR-6-1 1.53 1.53 4.24 6.33 9.53 8.26 6.35 1.6 SCREW Packaged in bags. RETAINER MATERIAL: Carbon Steel. RETAINER STANDARD FINISH: ET - Electro Plated Bright Tin ASTM B 545, Class A W/Preservative Coating. RETAINER OPTIONAL FINISH: DT - Matte Electro-Tin ASTM B 545, Class A W/ Clear Preservative Coating, Annealed. L T E Available with six-lobe recess on special order. Part Number Designation For Screw Four dimples on head designate metric thread. PSHP - 632 - L 1 C Metal Phillips Recess Type Thread Length Cap Color Style (Lobed) (Standard Black) (See page 5 for color capabilities) SMT-4 Screw Thread Length C E L T Driver Type ±.1 ±.1 ±.15 Nom. Size PSHP 44 PSHP 632.51.663.44.542 1.57.723.51.663.44.542 1.57.723 CAP MATERIAL: ABS. Temperature limit is 2 F / 93 C. SCREW MATERIAL: Carbon Steel. SCREW FINISH: CN - Bright Nickel over Copper Flash. Retainer and screw are sold separately. #1 #2 Screw Thread Length C E L T Driver Type ±.25 ±.25 ±.38 Nom. Size PSHP M3 PSHP M3.5 12.95 16.84 11.18 13.77 1 14.48 18.36 12.95 16.84 11.18 13.77 1 14.48 18.36 THREADS: External, ANSI B1.1, 2A ANSI/ASME B1.13M, 6g. (1) (1) As with all external plated threads, Class 2A/6g, the maximum major and pitch, after plating, may equal basic sizes and be gauged to Class 3A/6h, per ANSI B1.1, Section 8, Table 3A and ANSI B1.13M, Section 8, Paragraph 8.2. #1 #2
ASSEMBLY Simply snap screw into retainer to complete assembly. Black ABS cap standard. Optional molded-thru colors available. When Assembled Spring action of plastic fingers holds screw in retracted position. PSHP SMTPR PC Board P T 2 T 1 G Patented Screw Part Number Thread Thread Screw Retainer G P T 1 T 2 Total Size Type Length Part Number ±.25 ±.25 Nom. Nom. Radial Float.112-4.188. PSHP 44 SMTPR-6-1 (#4-4) 1.248.26.138-32.188. PSHP 632 SMTPR-6-1 (#6-32) 1.248.26.478.646.15.478.646.2 Screw Part Number Thread Thread Screw Retainer G P T 1 T 2 Total Size x Pitch Type Length Part Number ±.64 ±.64 Nom. Nom. Radial Float M3 x.5 PSHP M3 M3.5 x.6 PSHP M3.5 4.78 SMTPR-6-1 1 6.3.66 SMTPR-6-1 4.78 1 6.3.66 12.14 16.41.38 12.14 16.41.51 COLOR CAPABILITIES FOR TYPE PSHP SCREW The colors shown here (codes #2 thru #7) are non-stocked standards and available on special order. Since actual cap colors may vary slightly from those represented at the right, we recommend that you request samples for color verification. If you require a custom color or you need a color matched cap, please contact us. Non-flammable UL 94-V plastic caps are available on special order. Std. Black #1 Red #2 Orange #3 Yellow #4 Green #5 Blue #6 Violet #7 SMT-5
SURFACE MOUNT R ANGLE FASTENER Strong re-usable threads at right angle to PC board. T Grooves identify unified thread. Part Number Designation SMTRA 256-8 - 6 ET G J F C Type Thread Height Length Finish P K N D S P B Stencil Masking Examples L Patented. A Min. Hole Thread Thread Height Length Length Sheet Size A B C D Height G J K N P S P T Size Type L Thick- In Sheet ±.6 ±.6 ±.6 ±.6 F ±.6 Nom. Nom. Max. Max. ±.3 Nom. ±.5 ness +.3. ±.6.86-56 (#2-56) SMTRA 256 8 6.188.4.53.218.4.6.14.25.345.2.3.48.4.157.15.112-4 (#4-4) SMTRA 44 9 6.188.4.53.25.5.65.16.281.39.2.3.48.4.188.125.138-32 (#6-32) SMTRA 632 1 8.25.4.53.312.5.65.25.312.45.2.3.48.4.25.145.164-32 (#8-32) SMTRA 832 12 9.281.4.53.375.5.75.25.375.535.2.3.48.4.312.195 Min. Hole Thread Thread Height Length Length Sheet Size A B C D Height G J K N P S P T Size x Type L Thick- In Sheet ±.15 ±.15 ±.15 ±.15 F ±.15 Nom. Nom. Max. Max. ±.8 Nom. Pitch ±.13 ness +.8 ±.15 M2 x.4 SMTRA M2 6 5 5 1 1.35 5.5 1 1.5 3.5 6 8.4.5.75 1.22 1 4 2.65 M2.5 x.45 SMTRA M25 6 5 5 1 1.35 5.5 1 1.5 3.5 6 8.4.5.75 1.22 1 4 2.65 M3 x.5 SMTRA M3 7 5 5 1 1.35 6.35 1.25 1.65 4 7 9.75.5.75 1.22 1 4.75 3.2 M4 x.7 SMTRA M4 9 7 7 1 1.35 9.53 1.25 1.65 6.35 9 13.1.5.75 1.22 1 7.9 4.8 SMT-6 Thread Pad Width Pad Length Hole Spacing Hole Size P A P L S H In Sheet Min. Min. ±.2 +.3. 256.262.171.157.53 44.294.171.188.53 632.356.233.25.53 832.419.264.312.53 Thread Pad Width Pad Length Hole Spacing Hole Size P A P L S H In Sheet Min. Min. ±.5 +.8 M2 6.62 4.57 4 1.35 M25 6.62 4.57 4 1.35 M3 7.47 4.57 4.75 1.35 M4 1.65 6.57 7.9 1.35 P A Solder Pad Can be flush to edge. Plated through hole not required. S H P L Part Parts Pitch Tape Width Number Per Reel (mm) (mm) SMTRA256-8-6 375 16 24 SMTRA44-9-6 3 16 24 SMTRA632-1-8 2 2 32 SMTRA832-12-9 2 2 32 SMTRAM2-6-5 375 16 24 SMTRAM25-6-5 375 16 24 SMTRAM3-7-5 3 16 24 SMTRAM4-9-7 2 2 32 MATERIAL: Zinc Diecast. STANDARD FINISH: ET - Electro Plated Bright Tin, ASTM B 545, Class A W/ Clear Preservative Coating. OPTIONAL FINISH: DT - Matte Electro-Tin ASTM B 545, Class A W/ Clear Preservative Coating, Annealed. THREADS: Internal, ANSI B1.1 2B ANSI/ASME B1.13M, 6H
INSTALLATION NUTS AND SPACERS Kapton patch applied here for vacuum pick up. Solder paste applied to pad on PCB. Solder fastener in place using standard surface mount techniques. INSTALLATION PANEL FASTENER Kapton patch applied here for vacuum pick up. Solder paste applied to pad on PCB. Solder fastener in place using standard surface mount techniques. Screw snapped in place. INSTALLATION R ANGLE FASTENER Flat top for vacuum pick up. Solder paste applied to pad on PCB. Solder fastener in place using standard surface mount techniques. Undercut to accept solder fillet and permit flush to edge installation. ReelFast product performance is dependent upon application variables. We will be happy to provide samples for you to install. If required, we can also test your installed hardware and provide you with specific performance data. SMT-7
ADDITIONAL REELFAST SMT SOLUTIONS Surface mount technology can be applied to other fastener designs. Contact our Applications Engineering department for more information. RoHS compliance information can be found on our website. Specifications subject to change without notice. Check our website for the most current version of this bulletin. SMT-8 CAGE-46384