CONCEALED-HEAD SELF-CLINCHING STUDS AND STANDOFFS BULLETIN
|
|
|
- Evelyn Walton
- 5 years ago
- Views:
Transcription
1 ONEED-HED SEF-INHING SUDS ND SNDOFFS UEIN H 708 R E V. 409
2 ONEED-HED SUDS ND SNDOFFS hese studs and standoffs ensure permanent mounting in metal sheets as thin as in. / mm. he fastener head is locked securely in a blind, milled hole and is able to handle substantial loads. he concealed-head feature allows the side of the sheet opposite installation to remain smooth. Sheet preparation only requires a milled blind hole to the recommended minimum depth. enter-cutting end mills for hole preparation are available from PennEngineering. Installation of the concealed-head studs and standoffs is simple using a hollow anvil and solid punch. Place the head of the fastener in the hole and insert using any standard press. Displaced sheet metal flows smoothly around the head into the undercut. NOE: Some PEM self-clinching concealed-head studs meet NSM63540 specifications. For a complete Military Specification and National erospace Standards Reference Guide (ulletin NSM) check our web site. oncealed-head Stud oncealed-head Standoff ack side of sheet remains smooth ook for the PEM dimple trademark on studs and the PEM two groove trademark on standoffs. H-2 opyright 2008 PennEngineering.
3 UMINUM ND SINESS SEE SUDS YPES H, FH, H, FH / mm E ll dimensions are in inches. MERI UNIFIED ength ±.015 lind (ength code is in 16ths of an inch) Mounting Dist. Sheet Dia. of lind E In Size luminum Stainless hick ±.010 / ttached ness (1) o Edge Parts H H N.172 (#4-40) FH FH H H (#6-32) FH FH H H (#8-32) FH FH H H 032 N (#10-32) FH FH ll dimensions are in millimeters. ength ±0.4 lind Size x (ength code is in millimeters) Sheet Mounting Pitch Dia. luminum Stainless hick- ness M3 x 0.5 M4 x 0.7 M5 x 0.8 Dist. of lind E ±0.25 / (1) o Edge H H M N 4.37 FH FH H H M FH FH H H M5 N N FH FH In ttached Parts (1) lind holes may be deeper than minimums except where sheet material is at or near minimum thickness. Fasteners should always be installed so the flange is flush with the surface of the sheet. N Not available. PR NUMER DESIGNION H H = short shank FH = long shank Fastener Material = luminum = Stainless Size ength H-3
4 SINESS SEE SNDOFFS YPES, SOS YPE YPE SOS H H Style #1 Style #2 (Screw will not pass through unthreaded end) Style #3 (lind) ll dimensions are in inches. MERI UNIFIED ength lind (ength code is in 16ths of an inch) Sheet Mounting Size hick- Dia. Stainless ness of lind (4) Full (5) (1) 4 (2) 5 (2) 6 (2) 8 (3) 10 (3) 12 (3) 16 (3) (#4-40) SOS (1) 4 (1) 5 (2) 6 (2) 8 (3) 10 (3) 12 (3) 16 (3) (#6-32) SOS (1) 4 (1) 5 (2) 6 (2) 8 (3) 10 (3) 12 (3) 16 (3) (#8-32) SOS (1) 4 (1) 5 (1) 6 (1) 8 (2) 10 (3) 12 (3) 16 (3) (#10-32) SOS (1) 4 (1) 5 (1) 6 (1) 8 (2) 10 (2) 12 (3) 16 (3) (1/4-20) SOS ll dimensions are in millimeters. ength Sheet Size x (ength code is in millimeters) hick- Pitch Stainless ness M3 x 0.5 M4 x 0.7 M5 x 0.8 lind Mounting Diameter of lind (4) Full (5) M3 4 (1) 8(2) 6 (1) 10 (3) 12 (3) 16 (3) 20 (3) 25 (3) SOS 8 (3) M4 4 (1) 6 (1) 10(2) 8 (2) 12 (3) 16 (3) 20 (3) 25 (3) SOS 10 (3) M5 4 (1) 6 (1) 8 (1) 10 (2) 12 (2) 16 (3) 20 (3) 25 (3) SOS H Dist. Nom. / o Edge H Dist. Nom. / o Edge M6 x 1 SOS M6 4 (1) 6 (1) 8 (1) 10 (2) 12 (2) 16 (3) 20 (3) 25 (3) (1) Style #1. (2) Style #2. (3) Style #3. (4) lind mounting holes may be deeper than minimums except where sheet material is at or near minimum thickness. Fasteners should always be installed so the flange is flush with the surface of the sheet. (5) If standoff is used as a bushing, the hole in attached part must not exceed plus.020 / 0.51 mm. PR NUMER DESIGNION S = short shank SO = long shank S S Fastener Material S = Stainless Size ength H-4
5 PERFORMNE D (1) PERFORMNE D (1) ightening orque (in. lbs.) old-rolled Installation est Sheet Material 5052-H34 luminum Installation ightening orque old-rolled steel Installa- (kn) (N) est Sheet Material 5052-H34 luminum Installation (kn) (N) oncealed-head Standoffs oncealed-head Standoffs UNIFIED , , , , , , , , , , , , SOS , , , , , , H FH H FH oncealed-head Studs , , , , , , , , , , , , , , , , (2) (2) 1, (2) (2) 1, (2) (2) 2, (2) (2) 4, (2) (2) 1, (2) (2) 2, (2) (2) 3, (2) (2) 3, MERI M M M SOS M M M M oncealed-head Studs M H M M M FH M M M3 0.3 (2) (2) H M4 1.2 (2) (2) M (2) (2) M3 0.3 (2) (2) FH M4 1.2 (2) (2) M (2) (2) (1) he installation and pullout values reported are averages when all installation specifications and procedures are followed. Variations in mounting hole size, sheet material and installation procedure will affect this data. Performance testing of this product in your application is recommended. We will be happy to provide samples for this purpose. (2) Not applicable. MERI ND FINISH SPEIFIIONS s Fastener Materials Finish For Use In Sheet Hardness (3) External Internal, Passivated NSI / NSI / 300 Series and/or HR 70 / HR 50 / No Finish NSI / SME NSI / SME luminum Stainless tested per H 125 H M, 6g 1.13M, 6H SM 380 or ess or ess (3) HR - Hardness Rockwell Scale. H - Hardness rinell. H-5
6 INSION 1. Mill a blind hole to the correct minimum depth. Fasteners may also be installed into through holes. 2. Place fastener into anvil hole. 3. Place the sheet over the shank of the fastener. 4. With punch and anvil surfaces parallel, apply squeezing force until flange is flush with mounting sheet. *End mills available from PennEngineering. See chart below. s FH, FH, H, H oncealed-head studs PUNH s SOS, oncealed-head standoffs PUNH / 6.35 mm / 6.35 mm NVI NVI NVI D DIMENSIONS D D ll dimensions are in inches. ( ) UNIFIED H H FH FH SOS ll dimensions are in millimeters. (+0.08) M3 M4 M5 M6 MERI H H FH FH SOS END MI INFORMION Double-ended, two-flute H.S.S. center-cutting end mills are available from stock. PennEngineering does not manufacture center-cutting end mills, but we do keep a supply in stock for your convenience. Required Size PEM Fastener End Mill Part No. 440, M , M4 032, M5 FH, H, FH, H Studs.172 HM-172 SOS, Standoffs.213 HM-213 FH, H, FH, H Studs.213 HM-213 SOS, Standoffs.290 HM-290 FH, H, FH, H Studs.290 HM-290 SOS, Standoffs.312 HM-312 FH, H, FH, H Studs.312 HM-312 SOS, Standoffs.344 HM , M6 SOS Standoffs.390 HM-390 RoHS compliance information can be found on our website. Specifications subject to change without notice. heck our website for the most current version of this bulletin. H-6 GE-46384
S T U D S & Revised 406
C O N C E A L E D - H E A D S E L F - C L I N C H I N G S T U D S & S TA N D O F F S Revised 406 PEM CONCEALED-HEAD STUDS* AND STANDOFFS These studs and standoffs ensure permanent mounting in metal sheets
KEYHOLE STANDOFFS AND FASTENERS BULLETIN
BULLETIN SK 814 PEM KEYHOLE Standoffs ( SKC ) and sheet joining fasteners ( SKC-F ) are designed so that a PC board or panel can be quickly slipped into place and then removed from an assembly by simply
KEYHOLE STANDOFFS AND FASTENERS BULLETIN
BULLETIN SK 616 PEM KEYHOLE Standoffs ( SKC ) and sheet joining fasteners ( SKC-F ) are designed so that a PC board or panel can be quickly slipped into place and then removed from an assembly by simply
Fasteners. For Use in. Stainless. Steel Sheets. Revised 108
Fasteners For Use in Stainless Steel Sheets Revised 108 FASTENERS FOR USE IN STAINLESS STEEL SHEETS One of the very basics of self-clinching is that the fastener must be harder than the host sheet. Only
NYLON INSERT SELF-LOCKING FASTENERS BULLETIN
BULLIN PL 510 ffective mounting for reusable locking threads. he thread locking torque performance of PL and PL PMHX self-clinching fasteners is equivalent to applicable NASM25027 specifications. A nylon
FASTENERS FOR USE IN STAINLESS STEEL SHEETS BULLETIN
FSTENERS FOR USE IN STINLESS STEEL SHEETS BULLETIN SS 416 One of the very basics of self-clinching is that the fastener must always be harder than the host sheet to ensure proper and permanent installation.
FASTENERS FOR USE IN STAINLESS STEEL SHEETS BULLETIN
FSTENERS FOR USE IN STINLESS STEEL SHEETS BULLETIN SS 416 R e v 417 One of the very basics of self-clinching is that the fastener must always be harder than the host sheet to ensure proper and permanent
The edge you ve been waiting for
R I G H T A N G L E C L I N C H F A S T E N E R S The edge you ve been waiting for Revised 606 PEM R ANGLE RIGHT ANGLE CLINCH FASTENER TYPES RAA AND RAS Self-clinching PEM R ANGLE fasteners provide you
SPOTFAST FASTENERS BULLETIN
BULLETIN SF 1115 Allows permanent joining in metal to metal and metal to PCB/plastic panels Alternative to riveting and spot welding. No special installation equipment required. Flush or sub-flush on both
F A S T E N E R S F O R U S E W I T H P C B O A R D S
F A S T N R S F O R U S W I T H P B OA R S FASTNRS FOR US WITH P BOARS an satisfy component-to-board, board-to-board, and boardto-chassis production fastening needs using less attachment hardware. BROAHING
FASTENERS FOR USE WITH PC BOARDS BULLETIN
FASTNRS FOR US WITH P BOARS BULLTIN K 107 R e v. 509A FASTNRS FOR US WITH P BOARS an satisfy component-to-board, board-to-board, and board-to-chassis production fastening needs using less attachment hardware.
S ELF-CLINCHING N UTS. Revised 108
LF-LINHING N UT Revised 8 PM LF-LINHING NUT For load-bearing threads in thin sheets aluminum, steel, and other ductile materials. Proved Performance For over 6 years, PM brand self-clinching fasteners
PEM VARIMOUNT BONDING FASTENERS
Bulletin VM-917 PEM VariMount bonding fasteners are assemblies comprised of standard PEM fasteners mounted permanently into base plates. VM PEM VARIMOUNT BONDING FASTENERS The PEM VariMount fastening system
SELF-CLINCHING STUDS AND PINS
SELF-LINING S ND PINS F (flush-head) Studs are installed by placing them in punched or drilled holes in the sheets and squeezing into place with any standard press. The squeezing action embeds the head
SELF-CLINCHING TY-D CABLE TIE-MOUNTS BULLETIN
SELF-CLINCHING TY-D CABLE TIE-OUNTS BULLETIN TD 508 R E V. 809A SELF-CLINCHING CABLE TIE-OUNTS AND HOOS PE TY-D self-clinching tie-mounts and hooks provide secure attachment points for mounting wires to
Bulletin TK-518. For attachment of thin panels to plastics, common casting materials and other similar materials. NEW!
Bulletin TK-518 For attachment of thin panels to plastics, common casting materials and other similar materials. NEW! TK TACKSERT PINS For attachment of thin sheets to plastics, common casting materials
MATERIAL & FINISH SPECIFICATIONS INSTALLATION. For Types FH, FHS, FHA, FHL, FHLS, TFH, TFHS, HFH, HFHB, HFHS and HFE studs
MTERIL & FINIS SPEIFITIONS s (1) Fastener Materials Standard Finishes Optional Finish (2) For use in Sheet ardness: External, Precipi- Zinc Per Zinc Per 50 or 55 or 70 or 80 or 85 or 92 or NSI 300 2024-T4
Weld Screws, Weld Nuts, Clinch Studs
Weld Screws, Weld Nuts, Clinch Studs imensions; Mechanical & Performance Requirements Weld Screws Top Projection Style... 2 ottom Projection Style... 3 Weld Nuts Single Projection... 4 Multiple Projection...
TECH SHEET PEM - REF / TESTING CLINCH PERFORMANCE. SUBJECT: Testing clinch performance of self-clinching fasteners.
PEM - REF / TESTING CLINCH PERFORMANCE SUBJECT: Testing clinch performance of self-clinching fasteners. A self-clinching fastener s performance can be divided into two major types. The first is self-clinching
SELF-LOCKING FASTENERS
Bulletin LN-28 PEM self-clinching locknuts prevent mating hardware from loosening. LN SELF-LOCKING FASTENERS PEM SELF-CLINCHING LOCKNUTS PREVENT MATING HARDWARE FROM LOOSENING PEM self-clinching locknuts
SELF-LOCKING FASTENERS BULLETIN
BULLETIN LN 44 Rev 64 PEM SELF-CLINCHING PREVAILING TORQUE LOCKNUTS PREVENT MATING HARWARE FROM LOOSENING PEM self-clinching prevailing torque locknuts provide ideal solutions to prevent mating hardware
Surface. Mount. Fasteners. Revised 908
Surface Mount Fasteners Revised 98 SURFACE MOUNT FASTENERS PEM ReelFast surface mount nuts, spacers, panel fasteners and R ANGLE fasteners are mounted to printed circuit boards in the same manner as other
Bulletin SSA-516 REV 817. PEM brand SNAP-TOP standoffs are designed for permanent installation into metal panels or PC Boards SSA SNAP-TOP STANDOFFS
Bulletin SSA-516 REV 817 PEM brand SNAP-TOP standoffs are designed for permanent installation into metal panels or PC Boards SSA SNAP-TOP STANDOFFS PEM SNAP-TOP Standoffs are designed for permanent installation
Ideal for today s compact electronics BULLETIN MPF
Ideal for today s compact electronics BULLETIN MPF 13 R e v 513 IDEAL FOR TODAY S COMPACT ELECTRONICS Laptops Notebooks/Ultrabook Devices Tablets/eReaders Cell/Smart Phones Gaming/Hand Held Devices Ultrabook
Broaching-Type Fasteners Series CKF2 & CKFS2
Broaching-Type Fasteners CKF2 & CKFS2 CKF2 and CKFS2 broaching-type fasteners are designed for use on printed circuit boards and on most brittle or hard materials; such as, glass laminates, epoxy or resin
SELF-LOCKING FASTENERS BULLETIN
BULLETIN LN 216 Rev 816 PEM SELF-CLINCHING PREVAILING TORQUE LOCKNUTS PREVENT MATING HARWARE FROM LOOSENING PEM self-clinching prevailing torque locknuts provide ideal solutions to prevent mating hardware
TECH SHEET PEM - REF / REPAIR AND REPLACEMENT OF SELF-CLINCHING FASTENERS. SUBJECT: Repair and replacement of self-clinching fasteners
PEM - REF / REPAIR AND REPLACEMENT OF SELF-CLINCHING FASTENERS SUBJECT: Repair and replacement of self-clinching fasteners Properly installed self-clinching fasteners are designed to provide permanent
Surface. Mount. Fasteners. Revised 608
Surface Mount Fasteners Revised 608 SURFACE MOUNT FASTENERS PEM ReelFast surface mount nuts, spacers, panel fasteners and R ANGLE fasteners are mounted to printed circuit boards in the same manner as other
BLIND THREADED INSERTS CATALOG
BLIND THREADED INSERTS CATALOG 1114 Rev 315 INDEX Company Info and Capabilities 3-4 Atlas Blind ed Inserts and Studs Overview 5 SpinTite Blind ed Inserts Atlas Plus+Tite Blind ed Inserts Atlas MaxTite
Quarter-Turn Fasteners
Solutions Inc. SU-2300 Line Quarter-Turn Fasteners MIL-F-5591C * Approved The SU-2300 Line fasteners are designed for aircraft use and are used on external access panels and internal equipment. They are
TECH SHEET PEM - REF / AXIAL THREAD CLEARANCE. SUBJECT: Method for providing adequate axial thread clearance
SUBJECT: Method for providing adequate axial thread clearance In our long history of working with customers in the application of our self-clinching nuts, PennEngineering has seen numerous instances of
PEM BRAND ACCESS HARDWARE
c c e s s H a r d w a r e PM BRND SS HRDWR PM brand access hardware is designed with captive screws to help keep parts to a minimum and eliminate risks associated with loose hardware that could fall out
THE SELF-CLINCHING FASTENER HANDBOOK
THE PEM FASTENING SYSTEMS SELF-CLINCHING FASTENER HANDBOOK contents Brief fastener history...2 How and why self-clinching works...3 Anatomy of self-clinching...4 Types of self-clinching fasteners...5
THE SELF-CLINCHING FASTENER HANDBOOK
THE SELF-CLINCHING FASTENER HANDBOOK contents Brief fastener history........................................ 2 How and why self-clinching works.............................. 3 Anatomy of self-clinching.....................................
CATALOG ATLAS BLIND THREADED INSERTS
TLS atalog 1217 Rev 518 TLS brand blind threaded inserts provide strong and reusable permanent threads in sheet materials where only one side is accessible for hardware installation. TLOG TLS BLIND THREDED
P-FH & P-FHS SELF CLINCHING STUD
P-FH & P-FH LF The P-FH / P-FH LF is a threaded fastener which incorporates a knurled platform under the head, which when embedded in the sheet, displaces material into the cl ring ADVANTAG AY TO AMBL
Bulletin FIE-1018 FASTENER INSERTION EQUIPMENT
Bulletin FIE-1018 FASTENER INSERTION EQUIPMENT designed and built the first PEMSERTER automatic fastener installation press in the 1960 s as more and more self-clinching fastener users realized that further
ENGINEERING STANDARDS SECTION: D TOG-L-LOC V-LOC OVAL-LOC LANCE-N-LOC INFORMATION. Tog-L-Loc. How The Joining Process Works
Tog-L-Loc Tog-L-Loc is a circular, leakproof joint formed by drawing the metals into a circular "cup'' and then expanding the diameter to form a 360 radial lock below the bottom sheet. How The Joining
PEMSERTER Series 2000 Automatic Tooling Guide
PEM/MAN/002 ISSUE 6 13.06.07 SECTION CONTENTS PAGE HOW TO SELECT AUTOMATIC TOOLING 3-5 NUT TOOLING S, CLS, CLA, SP 6-7 NUT AND BLIND FASTENER TOOLING SMPS, F, B, BS 8 STUD TOOLING FH, FHS, FHL, TPS 9-10
SHUR-LOK CORPORATION TECHNICAL SALES BULLETIN
Page 1 of 11 1.0 INTRODUCTION: 1.1 This Technical Sales Bulletin describes installation procedure of SL850 Blind-Threaded and SL854 Thru-Threaded Pull-up type inserts. These procedures use the SLPGA850
Lenovo IdeaPad U310 NoteBook
Lenovo IdeaPad U310 NoteBook 2012-09-12 Lenovo IdeaPad U310-Overview Lenovo IdeaPad U310-Overview Top View Left Side View Comments: Bottom View Both the top case and bottom case are aluminum alloy material
ALLIGATOR All-Purpose Anchors
ALLIGATOR All-Purpose s Description ALLIGATOR anchors are designed to hold high loads in solid walls, ceilings, and floors... but also hold securely when they encounter an unexpected cavity, such as in
SPACERS & STANDOFFS. FOR CUSTOM DESIGNS: Visit our online Part Builder at keyelco.com 73 SECTION CONTENTS ASSORTMENT/MOUNT KITS
SPCERS & STNOFFS SECTION CONTENTS SSORTMENT/MOUNT KITS SPCERS Clear Hole.............................. 83 Clear Hole............................... 78 Threaded............................... 83 Economy
QUICK PRODUCT LOCATOR
QUICK PRODUCT LOCATOR INDEX 313 R e v. 613 Self-clinching fasteners are pressed into sheet metal panels as this as.016 /0.4mm. Broaching fasteners are pressed into PC board or other plastic materials as
TECH SHEET. PEM -REF / Surface Finishing Sheet Metal Assemblies Subject: Surface Finishing Sheet Metal Assemblies with Self-Clinching Fasteners
Introduction Steel and aluminum panels in assemblies often will undergo surface finishing for reasons ranging from cosmetics to performance, while stainless steel panels may require passivation. For any
MECHANICAL ASSEMBLY John Wiley & Sons, Inc. M. P. Groover, Fundamentals of Modern Manufacturing 2/e
MECHANICAL ASSEMBLY Threaded Fasteners Rivets and Eyelets Assembly Methods Based on Interference Fits Other Mechanical Fastening Methods Molding Inserts and Integral Fasteners Design for Assembly Mechanical
BrydgeAir Keyboard for ipad Air
BrydgeAir Keyboard for ipad Air May 3 rd. 2016 by XiaoMing Chen & Larry Zhang PennEngineering 1 BrydgeAir Keyboard for ipad Air Overview 2 BrydgeAir Keyboard for ipad Air Details & Findings Pictures and
ENGINEERING STANDARDS SECTION: TOG-L-LOC V-LOC LANCE-N-LOC INFORMATION. Tog-L-Loc. How The Joining Process Works
Tog-L-Loc Tog-L-Loc is a circular, leakproof joint formed by drawing the metals into a circular "cup'' and then expanding the diameter to form a 360 radial lock below the bottom sheet. How The Joining
Max. Rec. Load. Wt. Per Inch lbs. kn lbs. kn lbs. kg. Wt. Per Inch lbs. kn lbs. kn lbs. kg 750 F (399 C)
FIG. 10 FIG. 15 & 15L Function: Designed for use in pipe hanger assemblies. (Type 304 or 316 Stainless Steel upon request) Ordering: Specify figure number, rod size, length (), material, and finish. 650
Nokia 6 Cellphone. PennEngineering. April 7th, 2017 Xiaoming Chen. 1
Nokia 6 Cellphone April 7th, 2017 Xiaoming Chen PennEngineering 1 Overview Nokia 6 has a 5.5-inch FHD IPS display with a polarizer film covered with 2.5D Gorilla Glass for protection. The smartphone comes
HINGES SPECIFICATIONS. Hinge Chart - General Specifications
SPECIFICATIONS MORTISE HINGE SPECIFICATIONS FEATURES: Extruded brass, full mortise hinges are machined for precise installation and smooth movement. Knuckles are milled to a clearance of 0.010 (.25mm)
RIVETS AND THREADED INSERTS
RIVETS AND THREADED INSERTS Tri-Clamp, Multi-Grip, Dome Head and Stainless Steel Rivets Multi-Grip Rivets Adapt to All Material Types and Thicknesses Threaded Inserts Install Threads Into Blind Areas and
Est OA K L A N D, NJ S ELF -C LINCHING FASTENERS. captive. fastener corporation
captive fastener corporation CPTIVE Est. 1974 O K TION POR ENER COR FST N, NJ S EF -C INCHING FSTENERS Self-Clinching Fasteners Specifications are subject to change without notice. Not responsible for
BB1068 / BB1099 SERIES
068 / 099 SRIS LL RING TMPLT UTT HINGS HVY WIGHT Non-handed ase material: steel for series 068, stainless steel for series 099 High grade plated finishes Standard non-rising non-removable pin (NRP) Standard
3 11/16" [94.0mm] HANDRAIL HEIGHT PER LOCAL CODE AUTHORITY 6" [152.4mm]
![3 11/16 [94.0mm] HANDRAIL HEIGHT PER LOCAL CODE AUTHORITY 6 [152.4mm]](/thumbs/76/73879949.jpg "3 11/16 [94.0mm] HANDRAIL HEIGHT PER LOCAL CODE AUTHORITY 6 [152.4mm]")
PLEASE READ PLEASE READ THESE INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING THE P-OMM-INT INSTALLATION! THIS INSTRUCTION SHEET IS INTENDED TO PROVIDE A SPECIFIC GUIDE TO FOLLOW FOR THE INSTALLATION OF THIS
C13.11 HANDLES AND CONNECTION PIECES C13 SIDE HUNG WINDOWS
C13 SIDE HUNG WINDOWS C13.11 HANDLES AND CONNECTION PIECES 01.05.2014 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS
UNIQUE STRUX DESIGN PROVIDES EXCEPTIONAL PERFORMANCE
UNIQUE STRUX DESIGN PROVIDES EXCEPTIONAL PERFORMANCE Our high-performance STRUX fasteners offer a stronger and more reliable assembly alternative to traditional clinch and weld studs. Along with stud applications,
CHERRYLOCK 'A' BLIND RIVET
CHERRYLOCK 'A' BLIND RIVET SPS Fastener Division, a PCC Company CONTENTS CHERRYLOCK 'A' RIVET NAS1/1(A) CODE CR2172/7 ALUMINUM CR2572/7 MONEL CR2672/7 A-26 Features... 1 Installation... 1 Physical Properties...
UltraCon Masonry Fasteners High Performance in a Wide Range of Applications
UltraCon Masonry Fasteners High Performance in a Wide Range of Applications The UltraCon masonry fastening system from Elco Construction Products offers optimal performance in a wide range of masonry applications.
Google Pixel DISASSEMBLE. PennEngineering
Google Pixel DISASSEMBLE June 4th, 2018 Allen Wang PennEngineering www.pemnet.com 1 Google Pixel Teardown www.pemnet.com 2 Details & Findings Pictures and Description of the Google Pixel and our disassembly
Series 2000 Automatic Tooling Guide
CONTENTS SECTION PAGE HOW TO SELECT AUTOMATIC TOOLING 3-5 NUT TOOLING S, CLS, CLA, SP 6-7 NUT AND BLIND FASTENER TOOLING SMPS, F, B, BS 8 STUD TOOLING FH, FHS, FHL, TPS 9-10 ANVILS - FH THIN SHEET, FH4
HINGES SPECIFICATIONS
SPECIFICATIONS MORTISE HINGE SPECIFICATIONS FEATURES: Extruded brass, full mortise hinges are machined for precise installation and smooth movement. Knuckles are milled to a clearance of 0.010 (.25mm)
UltraCon Masonry Fasteners High Performance in a Wide Range of Applications
UltraCon Masonry Fasteners High Performance in a Wide Range of Applications The UltraCon masonry fastening system from Elco Construction Products offers optimal performance in a wide range of masonry applications.
Erickson Automatics Inc.
Erickson Automatics Inc. Custom Small Parts Specialists Precision Screw Machining Swiss CNC Screw Machining (13 Axes for Multi Tasks) CNC Machining D4 Escomatic Machining - Coil Fed Medical Machining Self-Clinching
Connecting elements for connecting hard-pressed steel with aluminium/steel
Connecting elements for connecting hard-pressed steel with aluminium/steel 1. The Tuk-Rivet punched rivet system The rivet comprises a rivet head, a shank area, one or more shank grooves and the cutting
Holemaking Products & Accessories
Holemaking Products & Holemaking Products & Made of top-of-the-line materials for longer lasting performance, Klein's diverse line of drill bits and holemaking products and accessories provide accuracy
DUO-TAPTITE. Fasteners DUO-TAPTITE. Thread Rolling Screws
Fasteners Percent thread chart... Page 8 Pilot hole sizes... Page 9 Typical torque performance... Page 10 Typical single punch extruded holes... Pages 11 & 12 Die cast cored holes... Page 12 CORFLEX...
TAPTITE 2000 Fasteners
TAPTITE 2000 Fasteners Unique Design Increases Performance TAPTITE 2000 fasteners are designed to provide the benefits of previous TAPTITE fastener products with an innovative new thread design the Radius
Apple iphone 8. PennEngineering
Apple iphone 8 March 2018 by Jon Brunk PennEngineering www.pemnet.com 1 Apple iphone 8 www.pemnet.com 2 Details & Findings Pictures and Description of the iphone 8 and our disassembly process. www.pemnet.com
Codes: INCO, INSI, INPISANIN, INPINZANI. Reference: FT INDE-en Date: 23/03/18 Revision: 7 Page: 1 of 6 IN-CO IN-HE IN-SI CHARACTERISTICS
Reference: FT -en Date: 23/03/18 Revision: 7 Page: 1 of 6 IN-CO IN-HE IN-SI INPISANIN INPINZANI CHARACTERISTICS Anchor for hollow elements as airbrick, dry wall, plaster wall, etc. Maximum load in thin
INTRODUCTION. EqunioxRoof.com. Pro Tip
INSTALLATION MANUAL INTRODUCTION The Equinox Louvered Roof System is designed to be installed in an aluminum frame. All these sections are 1/8" thick extruded aluminum. All engineering for this system
STAINLESS STEEL CONTINUOUS HINGES
STAINLESS STEEL ONTINUO HINGES ID stainless steel hinges are full height piano hinges that provide support for the full height of the door. For doors up to 600 lbs. 0 maximum door width Hinge leafs are
INSTALLATION GUIDE SM SOLAR MOUNT PUB15JUN15
MOUNT INSTALLATION GUIDE PUB5JUN5 Wrenches and Torque SM SOLAR Wrench Size Recommended Torque (ft-lbs) /4 Hardware 7/6 *0 3/8 Hardware 9/6 *30 # Hardware 5/6 0 Torques are not designed for use with wood
Operations and Instruction Manual G-Lok Anchorage - Model #????? Portable Concrete and Steel Anchorage Connector ANSI Z359.
TM Operations and Instruction Manual G-Lok Anchorage - Model #????? Portable Concrete and Steel Anchorage Connector ANSI Z359.1 5,000 lbs / 22kn Made in the USA 3/4 Fall Protection G-Lok s are to be used
Large Diameter Tapcon
CONCRETE ANCHORING SPECIALISTS Large Diameter Tapcon (LDT ) Anchors Finished head, Removable Anchor DESCRIPTION/SUGGESTED SPECIFICATIONS Self-threading Anchors SPECIFIED FOR ANCHORAGE INTO CONCRETE The
FASTENERS FOR SPECIAL MATERIALS
FSTENERS FOR SPEIL MTERILS Wherever you are... we have the solution! FSTENERS FOR SPEIL MTERILS INTRODUTION The introduction of new materials and their successful use by designers are usually dependant
CLWP6048. Classic Sign Family Wall Panel. Part Number / Specifications. 60" Wide x 48" High CHPL Panel Wall Mount. ISO / Perspective View.
ISO / Perspective View Dwg. Date: pril 7, 25 ll Drawings Copyright. WP6048HRS (Single-Sided) Standard - Rectangular Panel C Upgrade Panel Option - Horizontal rched WP6048HPS (Single-Sided) Upgrade - Peaked
P R O D U C T G U I D E A N D I N D E X T O B U L L E T I N S
P R O D U C T G U I D E A N D I N D E X T O B U L L E T I N S Revised 406 INTRODUCTION PennEngineering serves as a single source for fastening solutions, offering the hardware, equipment, and technical
Sheet Steel Facts. Most common head design for self-drilling, self-tapping screws.
Sheet Steel Facts Fastener Guide for Sheet Steel Building Products August, 2003 Fastener Materials Fasteners are manufactured from several materials and coatings. For the purpose of this fact sheet, the
Chapter Tests and Problems
Chapter Tests and Problems Chapter 11 Fasteners and Springs Test INSTRUCTIONS Answer the questions with short, complete statements or drawings as needed. QUESTIONS Define the screw thread terms given in
Instructions for Prepping an Opening for SOSS Invisible Hinges
Instructions for Prepping an Opening for SOSS Invisible Hinges IMPORTANT Use only Porter-Cable Template Guide Bushing #42024 (Lock Face Routing) and #42237 (Lock Nut) to assure the following guide bushing
Umbrella Inserts and Stubby Screens
ADHESIVE ANCHORING SPECIALISTS Umbrella Inserts and Stubby Screens High Performance Adhesive Systems for Fastening to Hollow Base Materials DESCRIPTION/ADVANTAGES Hollow Block Fastening with A7 Adhesive
Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System. Effectivity: Helicopters manufactured prior to January, 1981
Page 1 of 12 Date: December 2, 1981 Subject: Models: Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System F-28C and 280C Effectivity: Helicopters manufactured prior to
Le Max2. PennEngineering. September 26 th 2016 by Larry Zhang. 1
September 26 th 2016 by Larry Zhang PennEngineering 1 Overview 5.7-inch Super AMOLED display with 2560 1440 resolution (Quad HD /2K) 2.21-megapixel rear camera with dual pixel autofocus, 4K video capture;
Ordering Guide - Shaft Assemblies -
Ordering uide - Shaft ssemblies - S & TRS Series TRS - - SS - 4 ssembly Type S TRS Shaft Diameter Overall Length xxx - inches Shaft Material - 00 Steel SS - 440C Stainless Steel CR - Chrome Plated 00 Steel
Installation Manual Flat Track Series
Manual Flat Track Series Contents Safety...1 Parts...2 Hardware.......................................... 2 Tools Required..................................... 4.............................................
BULLeTIN PeM CAPTIve PANeL SCReWS 617 Rev 1117
BULLTIN PF PM PTIV PNL SRWS 617 R e v 1117 PM PTIV PNL SRWS PM brand captive panel screws are designed to help keep parts to a minimum and eliminate risks associated with loose hardware that could fall
28" Adjustable Solar Tilt Mount ADJ-28. Owner's Manual. Please read this manual BEFORE installing your solar tilt mount
28" Adjustable Solar Tilt Mount ADJ-28 Owner's Manual Please read this manual BEFORE installing your solar tilt mount SECTION 1 Introduction Mounting your solar panel inclined to an optimized angle with
Thread Repair & Thread Protection
Thread Repair & Thread Protection Screw Thread Inserts, Kits & Components for Industrial Maintenance, Repair and Overhaul Bulletin 998 C E R T I F I E D ISO 9001 AS 9100 TS 16949 ISO 14001 The HELI-COIL
BOLTS AND NUTS Square Bolts( Table 1 ) Hex Nuts ( Table 7 ) Heavy Hex Nuts (Table 7) Heavy Hex Structural Bolts ( Table 2 )
BOLTS AND NUTS 1493 An externally threaded fastener that must be assembled with a nut to perform its intended service is a bolt. (Example: heavy hex structural bolt.) An externally threaded fastener that
Product Information Report Nutserts
A B C A: Nutsert B: TSN (Thinsheet) Nutsert C: Large Flange Diamond Grip II ed Insert D: Standard Flange Diamond Grip II ed Insert E: Nutsert for Soft Materials D E Overview are inserts that, when installed,
RIVNUT. The Original Blind Rivet Nut. Tel Fax
The Original Blind Rivet Nut DISTRIBUTED BY: AIM Industries, Inc. 6216 Transit Road Depew, NY 14043 Tel. 716-681-6196 Fax. 716-681-1610 aimrivnut@aol.com www.aimfasteners.com PLUSNUT A commitment to quality
Tail Vise. Installation Instructions. (revised 10/11/2017)
Tail Vise Installation Instructions (revised 10/11/2017) Lie-Nielsen Tail Vise Instructions Table of Contents page About Your Tail Vise 3 Parts List 4 step 1. Prepare Your Bench Top 5 step 2. Prepare the
V blocks. Materials. V-block
V blocks I needed a pair of identical V-blocks to clamp the Bonelle/Quorn toolholder. I wanted to mill the sides of the tool holder parallell to the mandrel and bar bed centre lines. To get two identical
TAPTITE Fasteners. High Performance Thread Rolling Screws for Metals
TAPTITE 2000 Fasteners High Performance Thread Rolling Screws for Metals TAPTITE 2000 thread forming technology joins two unique concepts and advances fastener performance to new levels. TAPTITE 2000 fasteners
TANGENT SHELVING. Tangent has won numerous design awards since its introduction in 1997:
TANGENT SHELVING Tangent is an innovative, strong, and graceful shelving system. Tangent is unique because of its beautifully simple means of assembly. When the shelves are eased into their supports, they
Installation and Assembly: Flat \ Tilt Wall Mount for VESA 400x400
Installation and ssembly: Flat \ Tilt Wall Mount for VES 400x400 Model: T642-003 Max Load Capacity: 100 lb (45.4 kg) 3215 W. North ve. Melrose Park, IL 60160 (800) 729-0307 or (708) 865-8870 Fax: (708)
Chapter 7. Fasteners
Chapter 7 Fasteners LEARNING OBJECTIVES After studying this chapter, students will be able to: Identify several types of fasteners. Explain why inch-based fasteners are not interchangeable with metric-based
Installation and Assembly: Universal Projector Wall Arm
Installation and ssembly: Universal Projector Wall rm Models: PST-2955, PST-2955-W, PST-2955, PST-2955-W Max UL Load Capacity: 35 lb (5.8 kg) 2300 White Oak Circle urora, Il 60502 (800) 865-22 Fax: (800)
UNIT 9b: SCREW FASTENERS Introduction Functions Screw Features Elements Terms of a Thread Profile
UNIT 9b: SCREW FASTENERS Introduction A mechanical screw is a cylinder or cone that has a helical ridge called a thread. A helix has one or more turns, so a screw can have several turns. If the helix is