Proven Performance CARBIDE INSERTS. Proven Performance. Performance, Quality & Technology Will Turn Machining Into PROFIT!

Proven Performance CARBIDE INSERTS P S High Temp. Alloy Carbon Steel M Stainless Steel N Aluminum / Non Ferrous K Cast Iron U Proven Performance Performance, Quality & Technology Will Turn Machining Into PROFIT! Multi-Material

Anatomy of Insert Geometry Tolerances The physical characteristics of an insert that differentiates one shape from the next. The allowed deviation of all insert dimensions. Substrate The alloy carbide's properties, grain size, cobalt content. Coating Thin on the surface of the insert that allows for greater cutting speeds, wear resistance longer insert life. Grade A combination of substrate coating that determines the hardness toughness of the insert for the specific material application. Rake Angle The angle formed on the insert from the top surface area the bottom of the insert chip flow area when parallel to the floor. Geometry The physical characteristics of an insert that differentiates one shape from the next. Chipbreaker The formed groove or recess along the cutting edge of the insert that breaks chips into small manageable lengths. Relief Angle The angle measured from the vertical line perpendicular to the cutting edge of the insert the cutting face of the insert. Edge Preparation The process used to prepare the insert's edge cutting condition for specific application material. Achieved by honing, chamfering,"t" l or any combination thereof. 2 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com

Dorian First Choice CARBIDE INSERTS Proven Technology Performance Negative Insert Double Sided Cutting Edge with a Negative Relief Angle. The First Choice for high metal removal high precision finishing applications. Available molded or precision ground with a wide range of geometries, chipbreakers grades. Positive Insert Single Sided Cutting Edge with a Positive Relief Angle. The First Choice for light roughing to precision finishing applications. Available in multiple varieties of relief angles, geometries chipbreakers in both ANSI ISO styles, precision ground or molded. Insert Guide Roughing Hard Wear resistant PVD CVD Coating Small Nose radius Light Honed Edge Small Chipbreaker Wear Resistant Tough PVD CVD Coating Nose Radius Honed Cutting Edge Chipbreaker Tough Impact Resistant PVD CVD Coating Large Nose Radius Heavy Honed Cutting Edge Large Chip Breaker Small Depth of cut (a p ) Small Feed per Revolution (f n ) High Surface Cutting Speed (Vc) Use Coolant if Insert Allows Depth of cut (a p ) Feed per Revolution (f n ) Surface Cutting Speed (Vc) Use Coolant if Insert Allows Large Depth of cut (a p ) High Feed per Revolution (f n ) Low Surface Cutting Speed (Vc) Use Coolant if Insert Allows For Insert Best Performance Starting: : Optimum: Coolant: Follow the recommended use cutting parameters of the insert according to material application. For Roughing, use a tough, coated insert grade with a large nose radius, heavy honed cutting edge large chipbreaker. Cut at a low SFM with a large Depth of Cut (a p ) high Feed Rate per Rev. (f n ). For, use a hard, tough & wear resistant coated insert grade with a medium nose radius, honed cutting edge medium chipbreaker. Cut at a medium SFM with a medium Depth of Cut (a p ) medium Feed Rate per Rev. (f n ). For, use a hard & wear resistant coated insert grade with a small nose radius, sharp to light honed cutting edge small chipbreaker. Cut at a high SFM with a light Depth of Cut (ap) light Feed Rate per Rev. (f n ) Insert Wear, decrease Spindle Speed (n) /or increase Feed (f n ) or change to a harder insert grade. Insert Chipping, increase Spindle Speed (n), decrease Feed (f n ), /or change to a heavier honed edge or change to a tougher insert grade. Use Coolant, if the insert grade allows, always use high pressure coolant to remove the hot chips heat from the insert to reduce thermal shock. For Ultimate Performance Use Dorian Inserts with Dorian Jet-Stream Thru Coolant System. The insert will operate at a constant low temperature, with a clean undamaged cutting edge, Increasing Insert Life Up to 200%. Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com 3

Proven Performance 44% Longer Insert Life Than the With Higher Cutting Performance Consistent Tolerance Better Chip Control & Surface Finish CNMG-543-PER-DPC15HT Negative Turning Inserts 31% Reduced Down Time Insert Cost Customer Lehti Group Oy Part mm inch Material MocN315M (34CrNiMo6) Dia. 42.0 1.654 Workpiece Motor Shafts Length 200.0 7.874 Machine Okuma CNC Turning Center Quantity Per job 12,500 This Dorian insert replaced a leading competitor's insert used in a non affiliated independent manufacturing company. Performance Chart Roughing Semi CNMG-543-XXX-XXXX CNMG-543-PER-DPC15HT Vc 180 m/min. Vc 180 m/min. 594 feet/min. 594 feet/min. fn 0.55 mm per/ rev. fn 0.55 mm per/ rev. 0.0217 inch/ rev. 0.0217 inch/ rev. ap 4.0 mm ap 4.0 mm 0.1575 inch 0.1575 inch Condition Wet Condition Wet Insert Life 45 Min. per Edge Insert Life 65 Min. per Edge Minutes In Cut 70 65 60 55 50 45 40 35 30 25 20 10 5 This report is true verifiable by an independent source. The insert performance may vary depending on the material, machine used, machine set-up, machining process, cutting data, cutting fluid. 4 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com

Proven Performance 400% More Parts Produced Than the With Higher Cutting Performance Consistent Quality,Tolerance Better Chip Control & Surface Finish 80% Reduced Down Time Tooling Cost CNGG-432-SEF-DUP35RT Negative Turning Inserts Customer Pankl Racing System Part mm inch Material P116, 3,2 % Cr Dia. 19.0 0.748 Workpiece Piston Pin Length 40.0 1.575 Machine Mazak CNC Dual Turn 20 Quantity Per job 5,600 This Dorian insert replaced a leading competitor's insert used in a non affiliated independent manufacturing company. Performance Chart Roughing Semi CNGG-432-XXX-XXXX CNGG-432-SEF-DUP35RT Vc 180 m/min. Vc 180 m/min. 594 feet/min. 594 feet/min. fn 0.2 mm per/ rev. fn 0.2 mm per/ rev. 0.0079 inch/ rev. 0.0079 inch/ rev. ap 1.2 mm ap 1.2 mm 0.0472 inch 0.0472 inch Condition Wet Condition Wet Parts Per Edge 56 Pieces Parts Per Edge 280 Pieces Pieces machined per cutting edge 300 280 250 225 200 175 150 125 100 75 56 25 0 C This report is true verifiable by an independent source. The insert performance may vary depending on the material, machine used, machine set-up, machining process, cutting data, cutting fluid. Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com 5

Proven Performance 725% Longer Insert Life Than the With Higher Cutting Performance Consistent Tolerance Longer Cutting Edge Life & Surface Finish CNMG-432-PER-DPC15HT Negative Turning Inserts 88% Reduced Down Time Insert Cost NO Edge Fracture after 165 Minutes Edge Fractured after 20 Minutes. Customer Maschinenfabrik Mundil Part mm inch Material MocN315M (34CrNiMo6) Dia. 450.0 17.717 Workpiece Steel Roll Length 4000.0 157.480 Machine Weiler CNC Turning Center Quantity Per job, 13 This Dorian insert replaced a leading competitor's insert used in a non affiliated independent manufacturing company. Performance Chart Roughing Semi CNMG-432-XXX-XXXX CNMG-432-PER-DPC15HT Vc 60 m/min. Vc 60 m/min. 198 feet/min. 198 feet/min. fn 0.6 mm per/ rev. fn 0.6 mm per/ rev. 0.0236 inch/ rev. 0.0236 inch/ rev. ap 3.0 mm ap 3.0 mm 0.1181 inch 0.1181 inch Condition Wet Condition Wet Insert Life 20 Min. per Edge Insert Life 165 Min. per Edge Minutes in Cut 180 165 150 135 120 105 90 75 60 45 30 20 0 C This report is true verifiable by an independent source. The insert performance may vary depending on the material, machine used, machine set-up, machining process, cutting data, cutting fluid. 6 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com

Proven Performance 200% More Parts Produced Than the With Higher Cutting Performance Consistent Quality & Tolerance Better Chip Control & Surface Finish 67% Reduced Down Time Tooling Cost CNMG-432-PER-DPC15HT Negative Turning Inserts Customer Westfalia Part mm inch Material 1.057 Dia. 32.0 1.260 Workpiece Spherical Hinge Machine Padiroan CNC Turning Center Quantity Per job, 25,000 This Dorian insert replaced a leading competitor's insert used in a non affiliated independent manufacturing company. Performance Chart Roughing CNMG-432-XXX-XXXX CNMG-432-PER-DPC15HT Vc 260 m/min. Vc 260 m/min. 858 feet/min. 858 feet/min. fn 0,60 mm per/ rev. fn 0,60 mm per/ rev. 0.024 inch/ rev. 0.024 inch/ rev. ap 3.0 mm ap 3.0 mm 0.1181 inch 0.1181 inch Condition Wet Condition Wet Pieces machined per cutting edge 300 275 250 225 200 175 150 125 100 75 50 25 0 C Parts Per Edge 100 Pieces Parts Per Edge 300 Pieces This report is true verifiable by an independent source. The insert performance may vary depending on the material, machine used, machine set-up, machining process, cutting data, cutting fluid. Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com 7

Proven Performance 64% More Parts Produced Than the With Higher Cutting Performance Consistent Quality & Tolerance Better Chip Control & Surface Finish DCMT-32.51-PEF-DPC25UT Negative Turning Inserts 39% Reduced Down Time Tooling Cost Customer Plattner Part Material 1.5217 Workpiece Hallow Spacer Machine Hardinge CNC Turning Center Quantity Per job, 1,725 This Dorian insert replaced a leading competitor's insert used in a non affiliated independent manufacturing company. Performance Chart DCMT-32.51-XXX-XXXX DCMT-32.51-PEF-DPC25UT Vc 220 m/min. Vc 220 m/min. 726 feet/min. 726 feet/min. fn 0.16 mm per/ rev. fn 0.16 mm per/ rev. 0.00623 inch/ rev. 0.00623 inch/ rev. ap 0.2 mm ap 0.2 mm 0.0079 inch 0.0079 inch Condition Wet Condition Wet Pieces machined per cutting edge 120 110 100 90 80 70 60 50 40 30 20 10 0 Parts Per Edge 55 Pieces Parts Per Edge 90 Pieces This report is true verifiable by an independent source. The insert performance may vary depending on the material, machine used, machine set-up, machining process, cutting data, cutting fluid. 8 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com

Proven Performance 60% More Parts Produced Than the With Higher Cutting Performance Consistent Quality & Tolerance Better Chip Control & Surface Finish 38% Reduced Down Time Tooling Cost CNGG-432-SEM-DUP35RT Negative Turning Inserts Customer Erne Fittings Part Material 1.4571 Workpiece Fittings Machine Emco CNC Turning Center Quantity Per job, 20,000 This Dorian insert replaced a leading competitor's insert used in a non affiliated independent manufacturing company. Performance Chart CNMG-432-XXX-XXXX CNGG-432-SEM-DUP35RT Vc 130 m/min. Vc 130 m/min. 429 feet/min. 429 feet/min. fn 0.23 mm per/ rev. fn 0.23 mm per/ rev. 0.0091 inch/ rev. 0.0091 inch/ rev. ap 1.5 mm ap 1.5 mm 0.0591 inch 0.0591 inch Condition Wet Condition Wet Pieces machined per cutting edge 12 11 10 9 8 7 6 5 4 3 2 1 0 Parts Per Edge 5 Pieces Parts Per Edge 8 Pieces This report is true verifiable by an independent source. The insert performance may vary depending on the material, machine used, machine set-up, machining process, cutting data, cutting fluid. Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com 9

Proven Performance 14% More Parts Produced Than the With Higher Cutting Performance Consistent Quality & Tolerance Longer Cutting Edge Life & Surface Finish CNMG-543-KER-DKC15RT Negative Turning Inserts 13% Reduced Down Time Tooling Cost Customer H-SLR Part Material GGG50 Workpiece Fittings Machine Doosan CNC Turning Center Quantity Per job, 100,000 This Dorian insert replaced a leading competitor's insert used in a non affiliated independent manufacturing company. Performance Chart Roughing CNMG-543-XXX-XXXX CNMG-543-KER-DKC15RT Vc 150 m/min. Vc 150 m/min. 495 feet/min. 495 feet/min. fn 0.3 mm per/ rev. fn 0.3 mm per/ rev. 0.0118 inch/ rev. 0.0118 inch/ rev. ap 4.0 mm ap 4.0 mm 0.1575 inch 0.1575 inch Condition Wet Condition Wet Pieces machined per cutting edge 6.5 6 5.5 5 4.5 4 3.5 3 2.5 2 1.5 1 0 Dorian Tool Parts Per Edge 3.5 Pieces Parts Per Edge 4 Pieces This report is true verifiable by an independent source. The insert performance may vary depending on the material, machine used, machine set-up, machining process, cutting data, cutting fluid. 10 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com

Proven Performance 64% Longer Insert Life Than the With Higher Cutting Performance Consistent Tolerance Better Chip Control & Surface Finish 39% Reduced Down Time Tooling Cost DNMG-442-PEF-DPC25UT Negative Turning Inserts Customer Seimens Part mm inch Material St60-2 Dia. 68.0 2.677 Workpiece Worm Screw Length 252.0 9.921 Machine CNC Turning Center Quantity Per job, 1,750 This Dorian insert replaced a leading competitor's insert used in a non affiliated independent manufacturing company. Performance Chart Semi DNMG-442-XXX-XXXX DNMG-442-PEF-DPC25UT Vc 200 m/min. Vc 200 m/min. 660 feet/min. 660 feet/min. fn 0.3 mm per/ rev. fn 0.3 mm per/ rev. 0.0118 inch/ rev. 0.0118 inch/ rev. ap 2.5 mm ap 2.5 mm 0.0984 inch 0.0984 inch Condition Wet Condition Wet Minutes in Cut 175 165 150 135 120 105 90 75 60 45 30 15 0 Insert Life 107 Min. per Edge Insert Life 175 Min. per Edge This report is true verifiable by an independent source. The insert performance may vary depending on the material, machine used, machine set-up, machining process, cutting data, cutting fluid. Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com 11

Proven Performance 200% More Parts Produced Than the With Higher Cutting Performance Consistent Quality & Tolerance Better Chip Control & Surface Finish CNMG-432-MER-DMC30UT Negative Turning Inserts 67% Reduced Down Time Tooling Cost Customer Seydelmann Part mm inch Material 1.4301 Dia. 23.0 0.906 Workpiece Housing Length 180.0 7.087 Machine CNC Turning Center Quantity Per job, 1,233 This Dorian insert replaced a leading competitor's insert used in a non affiliated independent manufacturing company. Performance Chart Roughing CNMG-120408-XXX-XXXX CNMG-432-MER-DMC30UT Vc 160 m/min. Vc 160 m/min. 528 feet/min. 528 feet/min. fn 0.3 mm per/ rev. fn 0.3 mm per/ rev. 0.0118 inch/ rev. 0.0118 inch/ rev. ap 0.3 mm ap 0.3 mm 0.1181 inch 0.1181 inch Condition Wet Condition Wet Pieces machined per cutting edge 12 11 10 9 8 7 6 5 4 3 2 1 0 C Parts Per Edge 3 Pieces Parts Per Edge 9 Pieces This report is true verifiable by an independent source. The insert performance may vary depending on the material, machine used, machine set-up, machining process, cutting data, cutting fluid. 12 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com

Dorian Insert Grade Chart Peak Material P Carbon & Alloy Steel Range Turning Operation Roughing Hard & Wear Resistant High Cutting Speed Hard & Tough Impact & Wear Resistant Cutting Speed Tough Impact Resistant Low Cutting Speed 05 15 25 35 45 01 10 20 30 40 DPC15HT DPC25UT DPC35RT Choosing the Best Insert for the Turning Operation 1 For : Use a hard wear resistant coated insert grade with a small nose radius, a sharp to light honed cutting edge a small chipbreaker. Cut at a high SFM with a small Depth of Cut (a p ) Feed Rate per Rev. (fn). 2 For : Use a hard, tough wear resistant coated insert grade with a medium nose radius, honed cutting edge medium chipbreaker. Cut at a medium SFM with a medium Depth of Cut (a p ) medium Feed Rate per Rev. (fn) 3 For Roughing: Use a tough coated insert grade with a large nose radius, a heavy honed cutting edge a large chipbreaker. Cut at a low SFM with a large Depth of Cut (a p ) high Feed Rate per Rev. (fn). 4 Cutting Edge: If insert wears, reduce Spindle Speed RPM (n), increase Feed (fn) or change to a harder insert grade. If insert chips, increase Spindle Speed (n), decrease Feed (fn) /or to a heavier honed edge, or change to a tougher insert grade. For smooth surface hard material use hard insert, for interrupted cut large depth of cut use a tough insert. Description First Choice: For finishing turning applications at a high SFM. Use inserts to cut Steel Stainless Steel. Inserts have a hard, wear abrasive resistant substrate with a CVD Al 2 O 3 /TiCN/Al 2 O 3 /TiCN coating (not for interrupted cuts). First Choice: For universal turning applications at a medium SFM. Use inserts to cut Alloy Steel Stainless Steel. Inserts have a hard, tough, impact, wear abrasive resistant substrate with a CVD Al 2 O 3 /TiCN/Al 2 O 3 /TiCN coating. First Choice: For roughing applications at a low SFM. Use inserts to cut Alloy Steel Stainless Steel. Inserts have a tough impact resistant substrate with a CVD Al 2 O 3 /TiCN/Al 2 O 3 /TiCN coating. DUP15VT First Choice: For finish turning applications at a very high SFM. Use inserts to cut MultiMaterials; Ferrous non Ferrous including all High Temp Super Alloys. Inserts have a very hard, high wear abrasive resistant substrate with a PVD AlCrN Coating. U Multi Material DUP25UT First Choice: For universal turning applications at a high SFM. Use inserts to cut Multi Materials; Ferrous non Ferrous including all High Temp Super Alloys. Inserts have a hard wear resistant substrate with a PVD Tin/TiAlN/TiN Coating. DUP35RT First Choice: For unstable turning applications at a medium SFM. Use inserts to cut Multi Materials; Ferrous non Ferrous including all High Temp Super Alloys. Inserts have a wear, tough impact resistant substrate with a PVD TiAlN/ WC/C coating. M Stainless Steel DMC30UT First Choice: For general turning applications at a medium SFM. Use inserts to cut 300, 400 PH series Austenitic Stainless Steel. Inserts have a hard, tough, impact, abrasive thermal shock resistant substrate with a CVD TiCN/ TiN coating. K Cast Iron DKC10UT DKC15RT First Choice: For general turning applications at a medium SFM. Use inserts to cut all non Ferrous materials including Gray Iron Ductile Iron. Also, use inserts to cut Aluminum, Stainless Steel Hardened Steel. Inserts have an uncoated, wear abrasive resistant substrate. First Choice: For roughing applications at a medium SFM. Use inserts to cut Gray Iron, Nodular Cast Iron Ductile Iron. Inserts have a wear, tough impact resistant substrate with a CVD TiN/TiCNB/Al 2 /TiO 2 /3 Al 2 O 3 coating to withst interrupted cutting conditions. N Aluminum & Non Ferrous Material DNU10GT DNX10UT First Choice: For general turning applications at a high SFM. Use inserts to cut all non Ferrous metals including Aluminum Plastics. Inserts have an uncoated, hard, high abrasive resistant micro-grain substrate with a hard cutting edge. First Choice: For universal turning at a very high SFM. Use inserts to cut all non Ferrous materials including Aluminum, Stainless Steel, Plastics, High Temp Super Alloys low Silicone Aerospace Aluminum. Inserts have a hard, abrasive resistant substrate a microplus plasma TiAlN coating. S High Temp Alloy DUP15VT DUP25UT DUP35RT First Choice: For finish turning applications at a very high SFM. Use inserts to cut all non Ferrous materials including High Temp Super Alloys. Also, use inserts to cut all Ferrous materials. Inserts have a very hard, wear high abrasive resistant substrate with a PVD AlCrN coating. First Choice: For general turning applications at a high SFM. Use inserts to cut all non Ferrous materials including High Temp Super Alloys. Also, use inserts to cut all Ferrous materials. Inserts have a hard, tough wear resistant substrate with a PVD Tin/TiAlN/TiN Coating. First Choice: For unstable roughing applications at a medium SFM. Use inserts to cut all non Ferrous materials including High Temp Super Alloys. Also, use inserts to cut all Ferrous materials. Inserts have a tough impact resistant substrate with a PVD TiAlN/WC/C coating. For more information for grades not listed in this manual refer to our 2013 Turning & Boring catalog. Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com 13

Precision Positive Ground Turning Inserts Material Insert Grade General Roughing DNU10GT DUP15VT DUP25UT DUP35RT Insert Coating Uncoated PVD AlCrN PVD Tin/TiAlN/TiN PVD TiAlN/WC/C Inch Metric Inch Metric Inch Metric Inch Metric Depth of Cut ap.002 -.039 0.05-1.00.002 -.039 0.05-1.00.004 -.079 0.10-2.00.008 -.079 0.20-2.00 Feed per Rev. fn.002 -.008 0.05-0.20.002 -.008 0.05-0.20.002 -.012 0.05-0.30.002 -.016 0.05-0.40 Material Hardness HB HRC SFM (Vc) SFM (Vc) SFM (Vc) SFM (Vc) Low Alloy Steel 5% 180 10 1470-882 446-267 980-588 297-178 1089-545 330-165 Stainless Steel Austenitic 300 Series 180 10 668-347 203-105 1114-579 338-176 743-446 225-135 825-495 250-150 Gray Cast Iron Low Tensile Strength 180 10 722-375 219-114 1203-625 365-190 802-481 243-146 891-624 270-189 Aluminum 60 6353-1906 1925-578 8258-2477 2503-751 Non Ferrous Material Free Cutting Copper Alloy 90 1240-620 376-188 2067-1034 626-313 1723-861 522-261 1914-0957 580-290 High Temp Super Alloy Iron Base 200 15 174-104 53-32 290-174 88-53 223-134 68-41 248-149 75-45 Carbon-Graphite-Phenolics 171-86 52-26 285-143 86-43 238-119 72-36 264-211 80-64 Hardened Material 45 69-42 21-13 116-69 35-21 89-53 27-16 99-69 30-21 Description ANSI ISO UPC 733101- UPC 733101- UPC 733101- UPC 733101- CCGT-UEU CCGT-21.51-UEU CCGT-060204-UEU 79455 79456 79458 79459 CCGT-32.51-UEU CCGT-09T304-UEU 79465 79466 79468 79469 DCGT-UEU DCGT-21.51-UEU DCGT-070204-UEU 79535 79536 79538 79539 DCGT-32.51-UEU DCGT-11T304-UEU 79545 79546 79548 79549 DCGT-431-UEU DCGT-150404-UEU 79555 79556 79558 79559 DCGT-432-UEU DCGT-150408-UEU 79560 79561 79563 79564 TCGT-UEU 60º Triangle TCGT-21.51-UEU TCGT-110204-UEU 79595 79596 79598 79599 TCGT-32.51-UEU TCGT-16T304-UEU 79610 79611 79613 79614 TPGT-UEU 60º Triangle TPGT-21.51-UEU TPGT-110204-UEU 79630 79631 79633 79634 TPGT-32.51-UEU TPGT-6T304-UEU 79645 79646 79648 79649 VBGT-UEU 35º Diamond VBGT-221-UEU VBGT-110304-UEU 79660 79661 79663 79664 VBGT-331-UEU VBGT-160404-UEU 79670 79671 79673 79674 VCGT-UEU 35º Diamond VCGT-221-UEU VCGT-110304-UEU 79685 79686 79688 79689 VCGT-331-UEU VCGT-160404-UEU 79700 79701 79703 79704 WCGT-UEU 80º Trigon WCGT-21.51-UEU WCGT-040204-UEU 79725 79726 79728 79729 WCGT-32.51-UEU WCGT-06T304-UEU 79735 79736 79738 79739 14 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com

Molded Positive Turning Inserts Material Insert Grade Insert Coating Roughing DPC15HT DPC25UT DPC35RT CVD Al 2 O 3 /TiCN/Al 2 O 3 /TiCN CVD Al 2 O 3 /TiCN/Al 2 O 3 /TiCN CVD Al 2 O 3 /TiCN/Al 2 O 3 /TiCN Inch Metric Inch Metric Inch Metric Depth of Cut ap.002 -.039 0.05-1.00.004 -.118 0.10-3.00.008 -.157 0.20-4.00 Feed per Rev. fn.002 -.008 0.05-0.20.004 -.020 0.10-0.50.008 -.031 0.20-0.80 Material Hardness HB HRC SFM (Vc) SFM (Vc) SFM (Vc) Carbon Steel Annealed 125 1616-969 490-294 1346-808 408-245 1122-561 340-170 Alloy Steel Annealed 180 8 1140-684 346-207 950-570 288-173 792-396 240-120 Alloy Steel Heat Treated 300 32 570-342 173-104 475-285 144-86 396-198 120-60 Stainless Steel Austenitic 300 Series 180 8 808-485 245-147 673-404 204-122 561-281 170-85 Gray Cast Iron 180 8 990-693 300-210 Description ANSI ISO UPC 733101- UPC 733101- UPC 733101- CCMT-PEF CCMT-21.51-PEF CCMT-060204-PEF 71877 71878 CCMT-32.51-PEF CCMT-09T304-PEF 71883 71884 CCMT-PEM CCMT-21.51-PEM CCMT-060204-PEM 71934 CCMT-32.51-PEM CCMT-09T304-PEM 71935 71936 CCMT-32.52-PEM CCMT-09T308-PEF 71887 71888 DCMT-PEF DCMT-21.51-PEF DCMT-070204-PEF 71893 71894 DCMT-32.51-PEF DCMT-11T304-PEF 71897 71898 DCMT-PEM DCMT-21.51-PEM DCMT-070204-PEM 71895 71896 DCMT-32.51-PEM DCMT-11T304-PEM 71899 71900 TCMT-PEF 60º Triangle TCMT-1.21.20.2-PEF TCMT-06T101-PEF 80249 TCMT-21.50.5-PEF TCMT-110202-PEF 71909 71910 TCMT-21.51-PEF TCMT-110204-PEF 71911 71912 TCMT-PEM 60º Triangle TCMT-21.52-PEM TCMT-110208-PEM 71913 71914 TCMT-32.51-PEM TCMT-16T304-PEM 71915 71916 TCMT-32.52-PEM TCMT-16T308-PEM 71917 71918 TPMR-PEU 60º Triangle TPMR-221-PEU TPMR-110304-PEU 71945 71946 71947 TPMR-321-PEU TPMR-160304-PEU 71951 71952 71953 TPMR-322-PEU TPMR-160308-PEU 71954 71955 71956 VBMT-PEF 35º Diamond VBMT-331-PEF VBMT-160404-PEF 71919 71920 VBMT-332-PEF VBMT-160408-PEF 71921 71922 VCMT-PEF/ PEM 35º Diamond VCMT-221-PEF VCMT-110304-PEF 71925 71926 VCMT-331-PEF VCMT-160404-PEF 71927 71928 VCMT 332-PEM VCMT-160408-PEM 71929 71930 WCMT-PEF 80º Trigon WCMT-1.210.2-PEF WCMT-S20101-PEF 80251 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com 15

Molded Positive Turning Inserts Material Insert Grade Roughing DMC30UT DKC10UT DKC15RT Insert Coating CVD TiCN/TiN CVD TiN/TiCNB/Al 2 /TiO 3 /3Al 2 O 3 CVD TiN/TiCNB/Al 2 /TiO 3 /3Al 2 O 3 Inch Metric Inch Metric Inch Metric Depth of Cut ap.002 -.157 0.05-4.00.004 -.079 0.10-2.00.008 -.157 0.20-4.00 Feed per Rev. fn.004 -.024 0.10-0.60.002 -.012 0.05-0.30.004 -.016 0.10-0.40 Material Hardness HB HRC SFM (Vc) SFM (Vc) SFM (Vc) Austenitic Stainless Steel 300 Series 180 8 878-527 266-160 Ferritic Martensitic Stainless Steel 400 Series 330 34 559-335 169-102 Gray Cast Iron 180 8 1114-668 338-203 743-520 225-158 Nodular Cast Iron 160 8 1064-639 323-194 710-497 215-151 Description ANSI ISO UPC 733101- UPC 733101- UPC 733101- CCMT-MEM / CCMT-32.51-MEM CCMT-09T304-MEM 70750 CCMT-32.52-MEM CCMT-09T308-MEM 70751 CCMT-431-MEM CCMT-120404-MEM 70752 CCMT-KEM / CCMT-32.51-KEM CCMT-09T304-KEM 70753 CCMT-32.52-KEM CCMT-09T308-KEM 70754 CCMT-432-KEM CCMT-120408-KEM 70755 DCMT-MEM / DCMT-32.51-MEM DCMT-11T304-MEM 70760 DCMT-32.52-MEM DCMT-11T308-MEM 70761 DCMT-KEM DCMT-21.51-KEM DCMT-070204-KEM 70762 70763 DCMT-21.52-KEM DCMT-070208-KEM 70764 70765 DCMT-32.51-KEM DCMT-11T304-KEM 70766 70767 DCMT-32.52-KEM DCMT-11T308-KEM 70768 70769 SCMT-MEM Square SCMT-432-MEM SCMT-120408-MEM 70772 SCMT-KEM Square SCMT-432-KEM SCMT-120408-KEM 70773 TCMT-MEM 60º Triangle TCMT-21.51-MEM TCMT-110204-MEM 70776 TCMT-21.51-MEM TCMT-110208-MEM 70777 TCMT-32.51-MEM TCMT-16T304-MEM 70778 TCMT-32.52-MEM TCMT-16T308-MEM 70779 VCMT-MEM 35º Diamond VCMT-331-MEM VCMT-160404-MEM 70783 VCMT-332-MEM VCMT-160408-MEM 70784 VCMT-333-MEM VCMT-160412-MEM 70785 16 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com

Molded Positive Turning Inserts Material General DNU10GT DNX10UT Insert Coating Uncoated Micropuls Plasma TiAlN Inch Metric Inch Metric Depth of Cut ap.002 -.039 0.05-1.00.002 -.157 0.05-4.00 Feed per Rev. fn.002 -.008 0.05-0.20.002 -.020 0.05-0.50 Material Hardness HB HRC SFM (Vc) SFM (Vc) Aluminum 70 6353-1906 1925-578 8250-2475 2500-750 Magnesium-Zinc 10 2261-678 685-206 2937-881 890-267 Copper Alloy 1474-737 447-223 1914-957 580-290 Brass -Bronze 10 826-413 250-125 1073-536 325-163 Nylon- Plastic & Rubber 0 2246-674 681-204 2917-875 884-265 Carbon-Graphite-Phenolics 10 305-122 92-37 396-158 120-48 Description ANSI ISO UPC 733101- UPC 733101- CCGT-NFU CCGT-21.51-NFU CCGT-060204-NFU 80024 80025 CCGT-32.51-NFU CCGT-09T304-NFU 80032 80033 CCGT-32.52-NFU CCGT-09T308-NFU 80036 80037 CCGT-432-NFU CCGT-120408-NFU 80044 80045 DCGT-NFU DCGT-21.51-NFU DCGT-070204-NFU 80052 80053 DCGT-32.51-NFU DCGT-11T304-NFU 80060 80061 DCGT-32.52-NFU DCGT-11T308-NFU 80064 80065 RCGT-NFU Round RCGT-0602MO-NFU RCGT-0602MO-NFU 80068 80069 RCGT-0803MO-NFU RCGT-0803MO-NFU 80072 80073 RCGT-1003MO-NFU RCGT-1003MO-NFU 80076 80077 TCGT-NFU 60º Triangle TCGT-21.51-NFU TCGT-110204-NFU 80089 80090 TCGT-32.51-NFU TCGT-16T304-NFU 80093 80094 VCGT-NFU 35º Triangle VCGT-221-NFU VCGT-110304-NFU 80103 80104 VCGT-331-NFU VCGT-160404-NFU 80111 80112 VCGT-332-NFU VCGT-160408-NFU 80115 80116 VPGT-NFU 35º Triangle VPGT-221-NFU VPGT-110304-NFU 80127 VPGT-333-NFU VPGT-160412-NFU 80131 80133 WCGT-NFU 80º Trigon WCGT-32.51-NFU WCGT-06T304-NFU 80144 80145 WCGT-32.52-NFU WCGT-06T308-NFU 80148 80149 WCGT-431-NFU WCGT-080404-NFU 80152 80153 WCGT-432-NFU WCGT-080408-NFU 80156 80157 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com 17

Molded Negative Turning Inserts Material Roughing Insert Grade DPC15HT DPC25UT DPC35RT Insert Coating CVD Al 2 O 3 /TiCN/Al 2 O 3 /TiCN CVD Al 2 O 3 /TiCN/Al 2 O 3 /TiCN CVD Al 2 O 3 /TiCN/Al 2 O 3 /TiCN Inch Metric Inch Metric Inch Metric Depth of Cut ap.002 -.039 0.05-1.00.016 -.236 0.40-6.00.031 -.394 0.80-10.00 Feed per Rev. fn.004 -.079 0.10-2.00.004 -.020 0.10-0.50.008 -.031 0.20-0.80 Material Hardness HB HRC SFM (Vc) SFM (Vc) SFM (Vc) Carbon Steel Annealed 125 1616-969 490-294 1346-808 408-245 1122-561 340-170 Alloy Steel Annealed 180 8 1140-684 346-207 950-570 288-173 792-396 240-120 Alloy Steel Heat Treated 300 32 570-342 173-104 475-285 144-86 396-198 120-60 Stainless Steel Austenitic 300 Series 180 8 808-485 245-147 673-404 204-122 561-281 170-85 Gray Cast Iron 180 8 990-693 300-210 Description ANSI ISO UPC 733101- UPC 733101- UPC 733101- CNMG-PEF CNMG-431-PEF CNMG-120404-PEF 69250 69251 CNMG-PEM CNMG-432-PEM CNMG-120408-PEM 69408 69278 69279 CNMG-PER Roughing CNMG-432-PER CNMG-120408-PER 69351 69352 69353 CNMG-433-PER CNMG-120412-PER 69354 69355 69356 DNMG-PEF DNMG-331-PEF DNMG-110404-PEF 69254 DNMG-431-PEF DNMG-150404-PEF 69258 DNMG-441-PEF DNMG-150604-PEF 69262 DNMG-PEM DNMG-332-PEM DNMG-110408-PEM 69295 69296 DNMG-432-PEM DNMG-150408-PEM 69298 69299 DNMG-442-PEM DNMG-150608-PEM 69304 69305 DNMG-PER Roughing DNMG-432-PER DNMG-150408-PER 69375 69376 69377 DNMG-442-PER DNMG-150608-PER 69381 69382 69383 TNMG-PEF 60º Triangle TNMG-331-PEF TNMG-160404-PEF 69268 TNMG-PEM 60º Triangle TNMG-332-PEM TNMG-160408-PEM 69325 69326 69327 VNMG-PEF 35º Diamond VNMG-331-PEF VNMG-160404-PEF 69272 VNMG-332-PEF VNMG-160408-PEF 69274 69275 VNMG-PEM 35º Diamond VNMG-332-PEM VNMG-160408-PEM 69336 69337 69338 WNMG-PEM 80º Trigon WNMG-332-PEM WNMG-060408-PEM 69342 69343 WNMG-432-PEM WNMG-080408-PEM 69345 69346 WNMG-PER 80º Trigon Roughing WNMG-432-PER WNMG-080408-PER 69402 69403 69404 18 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com

Molded Negative Turning Inserts Material High Performance High Performance Roughing Insert Grade DPC15HT DPC25UT Insert Coating CVD l 2 O 3 /TiCN/Al 2 O 3 /TiCN CVD Al 2 O 3 /TiCN/Al 2 O 3 /TiCN Inch Metric Inch Metric Depth of Cut ap.031 -.126 0.80-3.20.016 -.157 0.40-4.00 Feed per Rev. fn.004 -.016 0.10-0.40.008 -.025 0.20-0.63 Material Hardness HB HRC SFM (Vc) SFM (Vc) Carbon Steel Annealed 125 1774-1064 538-323 1478-887 448-269 Alloy Steel Annealed 180 10 982-589 298-179 818-491 248-149 Alloy Steel Heat Treated 300 32 693-416 210-126 578-347 175-105 Description ANSI ISO UPC 733101- UPC 733101- CNMG-PEX High Performance CNMG-432-PEX CNMG-120408-PEX 69485 69486 DNMG-PEX High Performance DNMG-443-PEX DNMG-150612-PEX 69487 69488 Wiper Insert Technology Double Leading Angle To maximize insert cutting edge strength 118 15 R2 R1 R2 Triple Nose Radius To minimize cutting friction 3 Wiper Angle For high surface finish close turning tolerance 3 Rake Angle For chip control evacuation high rate of material removal Cutting Edge Preparation To minimize cutting pressure maximize insert life Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com 19

Molded Negative Turning Inserts Material Insert Grade Insert Coating Roughing DMC30UT DMC30UT DMC30UT CVD TiCN/TiN CVD TiCN/TiN CVD TiCN/TiN Inch Metric Inch Metric Inch Metric Depth of Cut ap.008 -.118 0.20-3.00.031 -.157 0.80-4.00.039 -.236 1.00-6.00 Feed per Rev. fn.002 -.012 0.05-0.30.004 -.016 0.10-0.40.008 -.031 0.20-0.80 Material Hardness HB HRC SFM (Vc) SFM (Vc) SFM (Vc) Austentic S. S. 300 Series 180 10 878-527 266-160 799-479 242-145 726-436 220-132 Ferritic Martensitic S.S. 400 Series 330 35 559-335 169-102 508-305 154-92 462-277 140-84 Precipitation Hardening S.S. 17-4-PH 330 35 499-299 151-91 454-272 138-83 413-248 125-75 Description ANSI ISO UPC 733101- UPC 733101- UPC 733101- CNMG-MEF CNMG-321-MEF CNMG-090304-MEF 69964 CNMG-431-MEF CNMG-120404-MEF 69965 CNMG-MEM CNMG-432-MEM CNMG-120408-MEM 69968 CNMG-MER Roughing CNMG-433-MER CNMG-120412-MER 69970 DNMG-MEF DNMG-331-MEF DNMG-110404-MEF 69973 DNMG-441-MEF DNMG-150604-MEF 69974 DNMG-442-MEF DNMG-150608-MEF 69975 DNMG-MEM DNMG-332-MEM DNMG-110408-MEM 69976 DNMG-432-MEM DNMG-150408-MEM 69977 DNMG-442-MEM DNMG-150608-MEM 69978 DNMG-MER Roughing DNMG-442-MER DNMG-150608-MER 69980 DNMG-443-MER DNMG-150612-MER 69981 WNMG-MEF 80º Trigon WNMG-331-MEF WNMG-060404-MEF 69989 WNMG-431-MEF WNMG-080404-MEF 69990 WNMG-MEM 80º Trigon WNMG-332-MEM WNMG-060408-MEM 69992 WNMG-432-MEM WNMG-080408-MEM 69993 WNMG-MER 80º Trigon Roughing WNMG-432-MER WNMG-080408-MER 69996 20 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com

Negative Ground Turning Inserts Material Insert Grade Insert Coating -Roughing DUP35RT PVD TiAlN/WC/C Inch Metric Depth of Cut ap.008 -.079 0.20-2.00 Feed per Rev. fn.002 -.016 0.05-0.40 Material Hardness HB HRC SFM (Vc) Aluminum 60 Non Ferrous Material Free Cutting Copper Alloy 90 1914-957 580-290 Heat Resistant Super Alloy Iron Base 200 15 248-149 75-45 Carbon-Graphite-Phenolics 264-211 80-64 Description ANSI ISO UPC 733101- CNGG-SEF CNGG-431-SEF CNGG-120404-SEF 69932 CNGG-432-SEF CNGG-120408-SEF 69933 CNMG-SEM CNMG-431-SEM CNMG-120404-SEM 69938 CNMG- 432-SEM CNMG-120408-SEM 69939 CNGG-SER Roughing CNGG-432-SER CNGG-120408-SER 69940 DNGG-SEF DNGG-431-SEF DNGG-150404-SEF 69942 DNGG-432-SEF DNGG-150408-SEF 69943 DNGG-441-SEF DNGG-150604-SEF 69945 DNGG-442-SEF DNGG-150608-SEF 69946 DNMG-SEM DNMG-431-SEM DNMG-150404-SEM 69948 DNMG-432-SEM DNMG-150408-SEM 69949 DNMG-441-SEM DNMG-150604-SEM 69951 DNMG-442-SEM DNMG-150608-SEM 69952 VNMG-SEF 35º Diamond VNMG-331-SEF VNMG-160404-SEF 69954 VNMG-332-SEF VNMG-160408-SEF 69955 WNGG-SEF 80º Trigon WNGG-431-SEF WNGG-080404-SEF 69956 WNGG-432-SEF WNGG-080408-SEF 69957 WNGG-SEM WNMG-SEM 80º Trigon WNMG-431-SEM WNMG-080404-SEM 69961 WNMG-432-SEM WNMG-080408-SEM 69962 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com 21

Hot Chips are Forced Away from the insert cutting edge. As a result, the insert will operate at a constant low temperature, with a clean undamaged cutting edge, changing the way metal is cut! At a close range of 1/4" (6mm) the Jet-Stream Coolant System aims the coolant precisely onto the cutting edge of the insert at a very high velocity. 22 Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com

For Ultimate Performacne Use Dorian Proven Performance Inserts with Dorian s Jet-Stream System Stringy Chips & Short Insert Life Without Dorian's Jet-Stream System Longer Insert Life & Shorter Chips With Dorian's Jet-Stream System Improve Quality, Productivity Increase Insert Life Up to 200% With Dorian's Jet-Stream System Call: 979-282-2861 Fax: 979-282-2951 Visit:www.doriantool.com E-mail:sales@doriantool.com 23

Insert Aptitude Manufacturer's Insert Grade Crossover Material Characteristic Performance ISO Coating Dorian Tool Ingersoll TaeguTec Iscar Kennametal Korloy Mitsubishi Svik Seco Sumitomo Tungaloy Hard & Wear Resistant High SFM If insert chips use DPC25UT P15 CVD DPC15HT TT8115 TT8125 IC9015 IC530N IC507 KC9110 NC3010 NC3020 UE6110 GC 4215 TP1500 AC810P AC900G T9105 T9115 Carbon Steel Annealed Alloy Steel Annealed Alloy Steel Heat Treated Forged Alloy Steel to Roughing Wear & Impact Resistant SFM If insert chips use DPC35RT If insert wears use DCP15HT P25 CVD DPC25UT TT5100 TT7100 TT8125 IC808 IC9054 KC9125 NC3120 NC3030 UE6020 GC 4225 TP2500 AC2000 AC830P T9125 Roughing & Interrupt Cut Tough & Impact Resistant Low SFM If insert wears use DCP25UT P40 CVD DPC35RT TT5100 TT7100 TT8135 IC3028 IC1008 KC9140 NC500H UE6035 UH6400 GC 4235 TP3500 AC3000 AC830P T9135 Stainless Steel: Austentic 300 Series Ferritic 400 Series Martensitic 400 Series 17-4-PH Series Roughing Wear Resistant SFM Tough & Impact Resistant Low SFM If insert chips use DMC30UT If insert wears use DUP25UT M20 PVD DUP25UT M35 CVD DMC30UT TT9215 TT9225 TT8020 TT9225 TT9235 IC1008 IC3028 IC1008 IC1028 KC9225 KCM15 KCM25 KC9240 KCM25 KCM35 NCM325 US7020 GC 2025 TM2000 AC610M NC9025 NCM335 US735 GC 235 TM4000 AC630M AC530U T6020 T9125 T6030 SH730 Hard & Wear Resistant High SFM If insert chips use DKC10UT K05 CVD DKC05UT TT1300 TT7310 IC428 IC4028 IC5005 KC9315 NC6105 NC6110 NC315K UC5105 GC 3005 TK1001 AC410K AC420K AC700G T5105 T5115 Gray Cast Iron Modular Cast Iron Malleable Cast Iron Wear & Impact Resistant SFM If insert chips use DKC15RT If insert wears use DKC05UT K10 CVD DKC10UT TT1300 TT7310 IC5010 IC1008 KC9315 KC9325 NC6105 NC6110 NC315K UC5105 GC 3005 TK1001 AC420K AC700G T5105 T5115 Roughing Tough & Impact Resistant Low SFM If insert wears use DKC10UT K20 CVD DKC15RT TT7310 TT6300 IC1008 IC9015 IC418 KC9325 NC5330 NC315K UC5115 H 13A TK2001 AC700G AC900G AC530U T5125 T9125 Aluminum Wear Resistant to High SFM Hard & Wear Resistant High SFM If insert wears use DNX10UT If insert wears use DCP15HT N10 N.A. DNU10GT K10 IC20 H01 HTi10 GC 1515 H1 N10 PVD DNX10UT IC520 KC5410 PD1000 KS05F KS15F TH10 Hard & Wear Resistant High SFM If insert chips use DUP25UT S10 PVD DUP15VT TT5080 IC807 IC907 KC5510 PC8110 NC9025 VP05RT GC 1025 CP200 AC510U EH510Z AH110 AH120 AH725 High Temp Alloys Super Alloy Wear & Impact Resistent SFM If insert chips use DUP35RT If insert wears use DUP15VT S25 PVD DUP25UT TT9215 TT9225 IC807 IC907 KC5510 KC5525 PC8110 NC9025 VP05RT VP10RT GC 1025 GC 1105 CP200 CP250 EH510Z EH520Z AH110 AH120 AH725 Roughing Tough & Impact Resistant Low SFM If insert wears use DUP25UT S25 PVD DUP35RT TT9225 TT9235 IC807 IC907 KC5525 PC8110 NC9025 VP15TF GC 1105 CP500 EH510Z EH520Z AH120 AH725 For our complete cross-over chart for all brs in excel format, e-mail sales@doriantool.com or call 979-282-2951. MPR08 MV 2013INSERT