TECHN. DATA SHEET 2016

TECHN. DATA SHEET 2016 valid from 01.2016 EXPERTS IN FALL PROTECTION

Product Overview AIO-Horizontal lifeline systems 08-17 AIO-ENDS 09 A IO-T Y P 09 AIO-GLEIT 09 AIO-EDLE 10-11 AIO-SZH 11 AIO-EB 11-12 AIO-SEIL 12 AIO-STA 12-14 AIO-STX 15 AIO-SYST 15 AIO-SYST-SZH 16 AIO-FALZ 16 AIO-SAND 17 AIO-VARIO 17 KIT-Horizontal lifeline systems 18-19 LIFELINE KIT 19 TEMP-Temporary lifeline systems 20-21 TEMP 21 VERT-Vertical lifeline systems 22-23 VERT 23 TAURUS-Rail systems 24-27 TAURUS 25-27 BARRIER-Guardrail systems / Side protection 28-31 BARRIER 28-31 LIGHT-Skylight protection systems 32-33 LIGHT 33 LIGHT-V2 33 LWP-LIGHT 33 MOBI 33 SDH / DAS-Safety hooks 34-35 SDH 35 DAS 35 FSG / FAS-Window safety railings 36-37 FSG 37 FAS 37 EAP-Single anchor points 38-45 EAP-STABIL 38-39 EAP-STX 39 EAP-SLING 39 EAP-POINT 39-40 EAP-QUAD 40-42 EAP-SPAR 42-43 EAP-LOCK 43 EAP-FALZ 43 EAP-SYST 44 EAP-SAND 45 EAP-VARIO 45 EAP-INDUSTRY 45 PSA-Personal protective equipments 46-47 STRING 46 PSA-SET 46 BRAKE 47 SHARK 47 KARI 47 TAPE 47 HSG 47 PSA-SCHRANK 47 Product accessories / Fastening accessories 48-49 Installation tools / Installation accessories 51 Fastening sets 52-53 Presentation models 55 Dimensions / Hole spacings / Drill patterns 56-57

AIO-Horizontal lifeline systems KIT-Horizontal lifeline systems TEMP-Temporary lifeline systems VERT-Vertical lifeline systems TAURUS-Rail systems BARRIER-Guardrail systems / Side protection LIGHT-Skylight protection systems SDH / DAS-Safety hooks QR-Code to Product Finder www.innotech.at FSG / FAS-Window safety railings EAP-Single anchor points PSA-Personal protective equipments Product accessories / Fastening accessories Installation tools / Installation accessories Fastening sets Presentation models Dimensions / Hole spacings / Drill patterns

AIO-Horizontal lifeline systems AIO ALL-IN-ONE-Horizontal lifeline systems INNOTECH s AIO Lifeline systems guarantee maximum range of mobility to rooftop workers. They can walk along either side of the system without decoupling and recoupling themselves. Flexible intermediate cable brackets and curve elements are perfectly adaptable to all sorts of roof and façade structures. The systems are equipped with the latest in pretension and shock absorption elements, in order to keep the fall stresses as low as possible. INNOTECH products are also statically and dynamically tested on the necessary substructures to fulfil the European standard EN 795:2015. Certified to the latest technological standards: EN 795:2012 TYP C und E CEN/TS 16415:2013 TAURUS Rail systems TAURUS, the aluminium rail system for use on all substructures, features variable rail connections and end units. These are easy to install and are adaptable to any surroundings thanks to curve and arch elements. Users of this system can move freely along the entire length of the rail and can work with the greatest range of motion. An automatic delaying unit, Speed Control, registers fall speeds. In case of a fall, the Allround rail slider immediately stops movements in all directions. Certified to the latest technological standards: Horizontal-System: EN 795:2012 TYP D, CEN/TS 16415:2013 Vertical-System: EN 353-1:2002, CNB/P/11.073 CEN/TS 16415:2013 Allround-System: EN 795:2012 TYP D, EN 353-1:2002 CNB/P/11.073, CEN/TS 16415:2013 Vertical Work BARRIER Guardrail systems /Side protection BARRIER by INNOTECH provides additional safety for persons who spend time on flat roofs. The multifaceted and customizable system can be adapted to a wide variety of roof types and preserves the aesthetic of the building. The VARIO system is anchored with a superimposed load, making it applicable without puncturing the rooftop. Certified to the latest technological standards: EN 13374:2013, EN ISO 14122-3:2014, DIN 14094-2:2007 NF E 85-015:2008 NEW! OPTIMISED SYSTEM! longer spacing (up to 2.2 m) Angle adjustment (90, 75 ) simple and fast installation with snap-lock mechanisms 4 EXPERTS IN FALL PROTECTION

AIO-Horizontal lifeline systems APPROVAL: Z-14.9-732 EAP Single anchor points Properly installed INNOTECH Single anchor points provide safety at windows and on flat and angled roofs in cases where integrating a lifeline system cannot reasonably be implemented. A wide range of single anchor points are available to fit all sorts of roof structures. The EAP single anchor points can be installed on all kinds of substructures. Certified to the latest technological standards: EN 795:2012 TYP A CEN/TS 16415:2013 TYP A DIBt general construction clearance N : Z-14.9-732 VERT Lifeline systems NEW! The VERTICAL lifeline system from INNOTECH is used for affixing employees with personal protective equipment for secure ascent and descent of ladders. High ease-of-use is guaranteed through preassembled components that ensure simple and quick installation. The innovative safety function of the new slider excludes a wrong application of the system. Directly connected to the slider is a special shock absorber that offers best shock absorption. All these advantages lead to an absolute quick and easy ascent /descent by using an intermediate bracket and a system that now can be completely passed over. Certified to the latest technological standards: EN 353-1:2014 LIGHT Skylight protection systems INNOTECH develops solutions for many different types of skylights, in order to protect workers from falling through whether the skylight is open or closed. The products, featuring an innovative installation system, stand out thanks to their ease of setup and refitting. They also provide optimal light and smoke permeability. Their force absorption is among the best due to their innovative shock absorption system. Certified to the latest technological standards: statically and dynamically tested according to EN 1263-1:2002 5

AIO-Horizontal lifeline systems SDH / DAS Safety roof hooks INNOTECH s Safety roof hooks only require a minimal wood layer and therefore adapt perfectly to the roof s particularities. SDH, which is available in various colors, has a gentle effect on the building s appearance and guarantees perfect safety - it passed the standards test in all stress directions, including along the y axis! Certified to the latest technological standards: EN 517:2006 Typ B, stress-tested in all directions TEMP Temporary lifeline systems TEMP, the temporary lifeline system from INNOTECH, can be installed quickly and easily and is therefore especially practical for short-term needs on construction sites or in industrial settings (steel, façades, warehouse and bridge construction, etc.) A handy intermediate bracket and a cable drum including a braking mechanism ensure maximum flexibility for temporary use. Certified to the latest technological standards: EN 795:2012 Typ B and C LIFELINE-KIT Lifeline systems The flexible lifeline system LIFELINE-KIT, packaged in a handy bucket, is wonderfully suited for quick and simple setup at myriad support structures. Approved for 4 persons (including 1 person for administering first aid), it is ideal for use on construction sites of all kinds (steel, façades, warehouse and bridge construction, etc. Certified to the latest technological standards: EN 795:2012 Typ C 6 EXPERTS IN FALL PROTECTION

AIO-Horizontal lifeline systems FSG / FAS Window safety railings INNOTECH s telescoping window safety railing FSG is easy to adjust to different widths, making it universally applicable. This provides optimal safety to individuals who need to perform maintenance or cleaning duties at open windows. After use, the FSG can be removed quickly and easily. When stored it can take on a compact shape! Certified to the latest technological standards: EN 12811-1, EN13374, EN HD 1000, tested with 125 kg ÖNORM B 4007 PSA personal protective equipment Selecting the personal protective equipment from the INNOTECH product portfolio provides the utmost safety for work on roofs, scaffoldings, ladders, façades, etc. High-quality systems can be easily combined to suit individual needs and offer a high degree of functionality, durability and user-friendliness. Certified to the latest technological standards: EN 361, EN 358, EN 354 QR-Code to Product Finder www.innotech.at 7

AIO-Horizontal lifeline systems AIO-system variants overview AIO-STA-16 BEF-403 AIO-SZH-10 AIO-STA-11 BEF-203 AIO-EB-10 AIO-ENDS-10 AIO-STA-10 BEF-206 AIO-EB-10 AIO-ENDS-10 AIO-VARIO-40 AIO-EB-10 AIO-ENDS-10 AIO-VARIO-20 AIO-SZH-10 AIO-SYST-20 AIO-EDLE-10 AIO-GLEIT-10 AIO-SAND-12 AIO-SZH-10 AIO-SYST-04-SZH AIO-SZH-10 AIO-STA-10 BEF-303 AIO-EB-10 AIO-ENDS-10 AIO-SYST-01 AIO-SZH-10 AIO-STA-12 BEF-404 BEF-404-1 AIO-SZH-10 AIO-EB-12 AIO-ENDS-10 AIO-STA-10 BEF-401-10 AIO-SZH-10 AIO-STX-10 AIO-EB-14 2 x AIO-ENDS-10 AIO-STA-12 BEF-107 AIO-EDLE-19 AIO-EB-11 AIO-ENDS-10 AIO-GLEIT-10 AIO-STA-10 BEF-201 AIO-EDLE-11 AIO-SZH-11 AIO-EDLE-12 8 EXPERTS IN FALL PROTECTION

AIO-Horizontal lifeline systems AIO-ENDS Illustration Catalog N Description AIO-ENDS-10 END LOCK SET for horizontal lifeline sytem (EN 795 C), aluminium (anodised) Complete set for one cable span, constant spring pre-tension and indicator clamp! Rating plate not included! AIO-TYP AIO-TYP-20-DE AIO-TYP-20-DK AIO-TYP-20-EN AIO-TYP-20-ES AIO-TYP-20-FR AIO-TYP-20-IT AIO-TYP-20-NL AIO-TYP-20-PL AIO-TYP-20-RO AIO-TYP-20-SK AIO-TYP-20-SV AIO-TYP-21-DE AIO-TYP-21-DK AIO-TYP-21-EN AIO-TYP-21-ES AIO-TYP-21-FR AIO-TYP-21-IT AIO-TYP-21-NL AIO-TYP-21-PL AIO-TYP-21-RO AIO-TYP-21-SK AIO-TYP-21-SV RATING PLATE (EN 795 C), plastic for identifying a horizontal lifeline system Various fastening options! Revision plaque included! DE = GERMAN / DK = DANISH / EN = ENGLISH / ES = SPANISH FR = FRENCH / IT = ITALIAN / NL = DUTCH / PL = POLISH / RO = ROMANIAN SK = SLOVAKIAN / SV = SWEDISH RATING PLATE (EN 795 C-E), plastic for identifying a self-supporting horizontal lifeline system Various fastening options! Revision plaque included! DE = GERMAN / DK = DANISH / EN = ENGLISH / ES = SPANISH FR = FRENCH / IT = ITALIAN / NL = DUTCH / PL = POLISH / RO = ROMANIAN SK = SLOVAKIAN / SV = SWEDISH AIO-GLEIT AIO-GLEIT-10-A4 FREE TO MOVE SLIDER, detachable, curve compatible (EN 795 B) Material: stainless steel (AISI 316) can be attached and detached at any point on the cable in the horizontal lifeline system free to move over all pass-through elements (intermediate cable brackets and curves) 1 pce. of triple-lock carabiner (EN 362) included! AIO-GLEIT-11 FREE TO MOVE ANCHOR POINT SLIDER, not detachable, not curve compatible, (EN 795 C) free to move the pass-through elements in overhead lifeline systems (intermediate cable brackets) 1 pce. of triple-lock carabiner (EN 362) included! AIO-GLEIT-12 FREE TO MOVE ANCHOR POINT SLIDER FOR CURVES, not detachable, curve compatible, (EN 795 C) free to move the pass-through elements in overhead lifeline systems (intermediate cable brackets and curves) 1 pce. of triple-lock carabiner (EN 362) and gap control gauge included! AIO-GLEIT-13-A4 FREE TO MOVE ANCHOR POINT SLIDER, not detachable, curve compatible, (EN 795 C) Material: stainless steel (AISI 316) free to move the pass-through elements (intermediate cable brackets and curves) 1 pce. of triple-lock carabiner (EN 362) included! ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 9

AIO-Horizontal lifeline systems AIO-EDLE Illustration Catalog N Description AIO-EDLE-10 STANDARD CORNER PASS-THROUGH ELEMENT, 90, can be passed over (EN 795 C) Mountable on: AIO-STA, AIO-STX, AIO-FALZ, AIO-SAND, AIO-VARIO, AIO-SYST, etc. Pass-over capability: inside and outside corners or overhead systems Connection: thread M16 for setting up a 90 corner set Variably adjustable cable angle thanks to bent base plate! Accessories for AIO-EDLE-10 AIO-EDLE-10- ROHRBOGEN-80 AIO-EDLE-10- ROHRBOGEN-105 AIO-EDLE-10- ROHRBOGEN-120 PIPE BEND, can be passed over (EN 795 C) Application: AIO-EDLE-10 Material: stainless steel (AISI 316) for setting up a 80, 105 or 120 corner set Pass-over capability: only outside! AIO-EDLE-10 not included! AIO-EDLE-11 AIO-EDLE-12 AIO-EDLE-13 AIO-EDLE-14 AIO-EDLE-16-1 AIO-EDLE-16-1,5 AIO-EDLE-16-3 STANDARD-CURVED CORNER PASS-THROUGH ELEMENT, 135, can be passed over (EN 795 C) Mountable on: AIO-STA, AIO-STX, AIO-FALZ, AIO-SAND, AIO-VARIO, AIO-SYST, etc. Pass-over capability: inside corners Connection: thread M16 for setting up a 135 corner set FACADE CURVED CORNER PASS-THROUGH ELEMENT, 90, can be passed over (EN 795 C) Mountable on: facade Pass-over capability: inside and outside corners or overhead systems Connection: fastening boreholes Ø 17 mm Through boreholes: 134 mm Engagement positions: 0, 45, 90, 135, 180 for setting up a 90 corner set FACADE CURVED CORNER PASS-THROUGH ELEMENT, 90, can be passed over (EN 795 C) Mountable on: steel construction Pass-over capability: inside and outside corners or overhead systems Connection: fastening boreholes Ø 17 mm Engagement positions: 0, 45, 90, 135, 180 for setting up a 90 corner set Restricted use as outside corners! STANDARD-CURVED CORNER PASS-THROUGH ELEMENT, variable, cannot be passed over (EN 795 C) Mountable on: AIO-STA, AIO-STX, AIO-FALZ, AIO-SAND, AIO-VARIO, AIO-SYST, etc. Pass-over capability: inside corners Connection: thread M16, plastic for setting up a variable corner set SPECIAL CURVED CORNER PASS-THROUGH ELEMENT, EXTENSION TUBE, can be passed over (EN 795 C) Pass-over capability: special corners Length: 1000 / 1500 / 3000 mm Curve corner: 0 Material: stainless steel (AISI 316) Suitable bending device or flaring tool required for connecting to AIO-EDLE-12 / -13 / -17 / -18! (page 51) AIO-EDLE-16-90 SPECIAL CURVED CORNER PASS-THROUGH ELEMENT, EXTENSION TUBE, 90 can be passed over (EN 795 C) Pass-over capability: special corners Length: 1000 mm Curve corner: 90 Material: stainless steel (AISI 316) Suitable bending device or flaring tool required for connecting to AIO-EDLE-12 / -13 / -17 / -18! (page 51) 10 EXPERTS IN FALL PROTECTION

AIO-Horizontal lifeline systems AIO-EDLE Illustration Catalog N Description AIO-EDLE-17 RETAINING BRACKET, offset on both sides, can be passed over (EN 795 C) Mountable on: AIO-STA, AIO-STX, AIO-FALZ, AIO-SAND, AIO-VARIO, AIO-SYST, etc. Pass-over capability: inside and outside corners or overhead systems Connection: thread M16 Engagement positions: 0, 45, 90, 135, 180 Only for use with 2 pcs. of AIO-EDLE-16 and AIO-EDLE-18! AIO-EDLE-18 RETAINING BRACKET, offset on one side, can be passed over (EN 795 C) Mountable on: AIO-STA, AIO-STX, AIO-FALZ, AIO-SAND, AIO-VARIO, AIO-SYST, etc. Pass-over capability: inside and outside corners or overhead systems Connection: thread M16 Engagement positions: 0, 45, 90, 135, 180 Only for use with 1 pce. of AIO-EDLE-16! AIO-EDLE-19 RETAINING BRACKET, variable up to 135, can be passed over (EN 795 C) Mountable on: AIO-STA, AIO-STX, AIO-FALZ, AIO-SAND, AIO-VARIO, AIO-SYST, etc. Pass-over capability: inside and outside corners or overhead systems Connection: thread M16 Engagement positions: 0, 45, 90, 135, 180 Angular displacement possible from 0, 180 up to 135! Suitable bending device or flaring tool required! (page 51) (exact dimensions page 57) AIO-SZH AIO-SZH-10 STANDARD-INTERMEDIATE BRACKET, can be passed over (EN 795 C) Mountable on: AIO-STA, AIO-STX, AIO-FALZ, AIO-SAND, AIO-VARIO, AIO-SYST, etc. Connection: thread M16 Function range: 220 For use on both sides without detaching the slider! AIO-SZH-11 FACADES-INTERMEDIATE BRACKET, can be passed over (EN 795 C) Mountable on: facades Connection: fastening boreholes Ø 17 mm Through boreholes: 134 mm Function range: 220 AIO-EB AIO-EB-10 STANDARD-END LOCK FASTENING, short (EN 795 C) Mountable on: AIO-STA, AIO-STX, AIO-FALZ, AIO-SAND, AIO-VARIO, AIO-SYST, etc. Connection: thread M16 for fastening the lifeline system with an end lock (AIO-ENDS-10) AIO-EB-11 STANDARD- END LOCK FASTENING, facade (EN 795 C) Mountable on: facade Connection: fastening boreholes Ø 17 mm Through boreholes: 134 mm for fastening the lifeline system with an end lock (AIO-ENDS-10) AIO-EB-12 STANDARD- END LOCK FASTENING, concrete wall (EN 795 C) Mountable on: concrete wall, facades Connection: Ø 13 mm for fastening the lifeline system with an end lock (AIO-ENDS-10) 90 to the wall Heavy duty anchors (BEF-104-A4) must not be used on weathered facades or insulation! (use 3 pcs. of adhesive anchorbilts M12) ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 11

AIO-Horizontal lifeline systems AIO-EB Illustration Catalog N Description AIO-EB-13 CORNER-END LOCK FASTENING, 90 (EN 795 C) Mountable on: AIO-STA, AIO-STX, AIO-FALZ, AIO-SAND, AIO-VARIO, AIO-SYST, etc. Connection: thread M16 for fastening two lifeline systems (AIO-ENDS-10) at an angle of 90 AIO-EB-14 CORNER-END LOCK FASTENING, 30 180 (EN 795 C) Mountable on: AIO-STA, AIO-STX, AIO-FALZ, AIO-SAND, AIO-VARIO, AIO-SYST, etc. Connection: thread M16 for fastening two lifeline systems (AIO-ENDS-10) at an angle of 30 180 AIO-EB-15 STANDARD- END LOCK FASTENING, long (EN 795 C) Mountable on: AIO-STA, AIO-STX, AIO-FALZ, AIO-SAND, AIO-VARIO, AIO-SYST, etc. Connection: thread M16 for fastening the lifeline system with an end lock (AIO-ENDS-10) AIO-SEIL AIO-SEIL-30 STAINLESS STEEL CABLE (EN 795 C) Dimensions: Ø 8 mm (7 x 7) Breaking load: 37 kn Material: stainless steel (AISI 316) tested for INNOTECH-lifeline systems AIO-STA-10 AIO-STA-10-300 AIO-STA-10-400 AIO-STA-10-500 AIO-STA-10-600 AIO-STA-10-500-A4 AIO-STA-10-600-A4 STANDARD POST in AIO-lifeline system (EN 795 C) Mountable on: concrete, wood, trapezoidal supporting sheet, steel construction, etc. Post height: 300 / 400 / 500 / 600 mm, Ø 48 mm Base plate dimensions: 150 x 150 x 8 mm / stainless steel (AISI 316) Thermal insulation cap and sealing sleeve see Product accessories (page 48)! Fastening sets not included! (see following page) Special lengths upon request! AIO-STA-11 AIO-STA-11-340 AIO-STA-11-470 STEEP ROOF POST in AIO-lifeline system (EN 795 C) Mountable on: concrete, wood, trapezoidal supporting sheet, steel construction, etc. Post height: 340 / 470 mm, Ø 48 mm Base plate dimensions: 150 x 150 x 8 mm Thermal insulation cap and sealing sleeve see Product accessories (page 48)! Fastening sets not included! (see following page) Special lengths upon request! 12 EXPERTS IN FALL PROTECTION

AIO-Horizontal lifeline systems Fastening sets for AIO-STA-10 und AIO-STA-11 Illustration Catalog Nr. Description BEF-104-A4 CONCRETE (min. C20/25) cracked and uncracked Material: stainless steel (AISI 316) Package: 4 x anchor bolts FISCHER FAZ II 12/10 A4 Drill depth min. 105 mm (Ø 12 mm)! BEF-201 BEF-203 BEF-206 BEF-303 BEF-303-1 BEF-303-3 BEF-401-10 WOOD TIMBER RAFTER (min. 16 x 16 cm) Package: 8 x fastening bolts (8 x 140 mm) 8 x washer (coniform) Min. penetration into static load-bearing construction: 100 mm! WOOD STEEP ROOF, TIMBER RAFTER (min. 8 x 10 cm) Package: 1 x steep roof fastening bar (1250 x 195 x 35 mm) 8 x fastening bolts (8 x 220 mm) (includes fastening accessories for post installation) Min. penetration into static load-bearing construction: 90 mm! WOOD RIDGE INSTALLATION, TIMBER RAFTER (min. 8 x 8 cm) Wood cross-section of load-bearing wood min. 80 x 80 mm, strength of panelling 20 mm! Min. penetration into static load-bearing construction: 80 mm! For the fixation 12 pcs. fastening bolts are required. Fastening material not included! (page 49) TRAPEZOIDAL SUPPORTING SHEET, FASTENING FRAME Dimensions: 840 x 840 x 40 mm Sheet metal thickness: min. 0.6 mm for optimal load distribution on trapezoidal supporting sheet, widely varied useability Fastening set (BEF-303-1 / BEF-303-3) not included! TRAPEZOIDAL SUPPORTING SHEET, QUICK FASTENING BRACKET Package: 4 x fastening bracket 16 x bore fastener Sheet metal thickness: min. 0.6 mm Raised bead width: min. 60 mm (exact dimensions page 57) TRAPEZOIDAL SUPPORTING SHEET, SPECIAL TOGGLE FASTENER Package: 4 x special toggle fastener Sheet metal thickness: min. 0.6 mm Raised bead width: max. 60 mm Free space under raised bead min. 115 mm, bore diameter Ø 28 mm (exact dimensions page 57) STEEL CONSTRUCTION, COUNTER PLATE (150 x 150 x 8 mm) Max. width of steel construction: 105 mm Fastening accessories not included! (page 49) NEW! BEF-403 BEF-412 STEEL CONSTRUCTION, COUNTER PLATE (140 x 20 x 10 mm) Packaging unit: 2 pieces Max. width of steel construction: 105 mm Fastening accessories not included! (page 49) STEEL CONSTRUCTION, CLAMPING CONSOLE Flange thickness: 10 up to 40 mm Width of steel beam: 125 415 mm ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 13

AIO-Horizontal lifeline systems AIO-STA-12 Illustration Catalog N Description AIO-STA-12-300 AIO-STA-12-400 AIO-STA-12-500 AIO-STA-12-600 AIO-STA-12-700 AIO-STA-12-800 STANDARD POST (base plate 300 x 300 mm) in AIO-lifeline system (EN 795 C) Mountable on: concrete, hollow concrete slab, trapezoidal supporting sheet, steel construction, etc. Post height: 300 / 400 / 500 / 600 / 700 / 800 mm, Ø 48 mm Base plate dimensions: 300 x 300 x 8 mm Thermal insulation cap and sealing sleeve see Product accessories (page 48)! Fastening sets not included! (see below) Special lengths upon request! Fastening sets for AIO-STA-12 AIO-STA-16 BEF-104-A4 CONCRETE (min. C20/25) cracked and uncracked Material: stainless steel (AISI 316) Package: 4 x anchor bolts FISCHER FAZ II 12/10 A4 Drill depth min. 105 mm (Ø 12 mm)! BEF-107 HOLLOW CONCRETE SLAB (min. C50/60, B4) Package: 8 x hollow core anchor FISCHER FHY-M10 x 52 8 x hex bolt M10 x 60 (DIN 933) / 8 x washer (M10) hollow slab cross-section (concrete thickness) min. 30 mm BEF-303 BEF-303-1 BEF-303-3 BEF-401-12 BEF-404 BEF-404-1 TRAPEZOIDAL SUPPORTING SHEET, FASTENING FRAME Dimensions: 840 x 840 x 40 mm Sheet metal thickness: min. 0.6 mm for optimal load distribution on trapezoidal supporting sheet, widely varied useability Fastening set (BEF-303-1 / BEF-303-3) not included! TRAPEZOIDAL SUPPORTING SHEET, QUICK FASTENING BRACKET Package: 4 x fastening bracket / 16 x bore fastener Sheet metal thickness: min. 0.6 mm Raised bead width: min. 60 mm (exact dimensions page 57) TRAPEZOIDAL SUPPORTING SHEET, SPECIAL TOGGLE FASTENER Package: 4 x special toggle fastener Sheet metal thickness: min. 0.6 mm Raised bead width: max. 60 mm Free space under raised bead min. 115 mm, bore diameter Ø 28 mm (exact dimensions page 57) STEEL CONSTRUCTION, COUNTER PLATE (300 x 300 x 8 mm) Max. width of steel construction: 185 mm or 255 mm Fastening accessories not included! (page 49) TRAPEZOIDAL SUPPORTING SHEET, SCREW FASTENER Package: 4 x counter plate incl. screw material, sealing washer Sheet metal thickness: min. 0.7 mm Only for limited use in the AIO-lifeline system (BEF-404-1)! NEW! TRAPEZOIDAL SUPPORTING SHEET, STABILISATION BAR Package: 2 x support bars / 4 x bore fastener / 4 x centring washer Sheet metal thickness: min. 0.7 mm Only in combination of BEF-404 to stabilise corner- and end points! AIO-STA-16-200 AIO-STA-16-500 STANDARD POST, lateral base plate, in AIO-lifeline system (EN 795 C) Mountable on: concrete (anchoring depth at least 100 mm), steel construction, etc. Post height: 200 / 500 mm, Ø 48 mm Base plate dimensions: 150 x 192 x 8 mm (use 4 pcs. of adhesive anchor bolts M12) Fastening sets not included! (see below) Special lengths upon request! Fastening sets for AIO-STA-16 BEF-401-10 BEF-403 STEEL CONSTRUCTION, COUNTER PLATE (150 x 150 x 8 mm) Max. width of steel construction: 105 mm Fastening accessories not included! (page 49) STEEL CONSTRUCTION, COUNTER PLATE (140 x 20 x 10 mm) Packaging unit: 2 pieces Max. width of steel construction: 105 mm Fastening accessories not included! (page 49) 14 EXPERTS IN FALL PROTECTION

AIO-Horizontal lifeline systems AIO-STX-10 Illustration Catalog N Description AIO-STX-10-100-250 QUICK INSTALLATION POST in AIO-lifeline system (EN 795 C) Mountable on: trapezoidal supporting sheet Material: steel Material thickness (without coating): min. 0.75 mm Insulation thickness: 100 250 mm Post height: over aquifer c. 200 mm Material: coated steel (RAL 9005), aluminium, stainless steel (AISI 304) After installation the post has to be sealed in professionally! Fastening accessories (4 pcs. bore fastener per post) and installation tools not included! (page 51) Accessories for STX-10 BBF-4,8-160-0-VZ BBF-4,8-200-0-VZ BBF-4,8-240-0-VZ BBF-4,8-280-0-VZ bore fastener, hexagonal A/F8, Ø 4.8 x 160, IR2, galvanised for insulation thickness of 100 140 mm, galvanised bore fastener, hexagonal A/F8, Ø 4.8 x 200, IR2, galvanised for insulation thickness of 135 180 mm, galvanised bore fastener, hexagonal A/F8, Ø 4.8 x 240, IR2, galvanised for insulation thickness of 175 220 mm, galvanised bore fastener, hexagonal A/F8, Ø 4.8 x 280, IR2, galvanised for insulation thickness of 215 250 mm, galvanised AIO-SYST AIO-SYST-01-410-610 AIO-SYST-03-500 AIO-SYST-04-305-333 AIO-SYST-04-400-500 AIO-SYST-06-465 AIO-SYST-09-500 AIO-SYST-20-475-695 END-, CORNER POINT in AIO-lifeline system for standing seam roofs (EN 795 C) Mountable on: (Double-) standing seam roofs Material (Material thickness): steel (min. 0.5 mm), aluminium (min. 0.7 mm) Width of profile: 410 610 mm Pre-assembled and without roof perforation! Not suitable for copper roofs use AIO-FALZ-45! END-, CORNER POINT in AIO-lifeline system for ZAMBELLI RIB-ROOF SPEED 500 (EN 795 C) Mountable on: system roof ZAMBELLI RIB-ROOF SPEED 500 Material (Material thickness): steel (min. 0.63 mm), aluminium (min. 0.7 mm) Width of profile : 410 510 mm Pre-assembled and without roof perforation! END-, CORNER POINT in AIO-lifeline system for system roofs (EN 795 C) Mountable on: system roofs similar to KALZIP, INTERFALZ Material (Material thickness): steel (min. 0.5 mm), aluminium (min. 0.7 mm) Width of profile : 305 333 mm or 400 500 mm Pre-assembled and without roof perforation! END-, CORNER POINT in AIO-lifeline system for ZAMBELLI RIB-ROOF 465 (EN 795 C) Mountable on: system roof ZAMBELLI RIB-ROOF 465 Material (Material thickness): steel (min. 0.63 mm), aluminium (min. 0.7 mm) Width of profile : 410 510 mm Pre-assembled and without roof perforation! END-, CORNER POINT AND INTERMEDIATE CABLE BRACKET in AIO-lifeline system for ZAMBELLI RIB-ROOF Evolution (EN 795 C) Mountable on: system roof ZAMBELLI RIB-ROOF Evolution Material (Material thickness): aluminium (min. 0.7 mm) Width of profile : 410 510 mm For use as end point, AIO-SHOCK-10 must be ordered! Pre-assembled and without roof perforation! END-, CORNER POINT in AIO- lifeline system for trapezoidal covering sheet (EN 795 C) Mountable on: trapezoidal covering sheet Material: steel, aluminium Material thickness: min. 0.5 mm Width of profile: 475 695 mm Fastening set and sealing strips for trapezoidal cover included! (exact dimensions page 57) ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 15

AIO-Horizontal lifeline systems AIO-SYST-SZH Illustration Catalog N Description AIO-SYST-01-410-610-SZH AIO-SYST-03-500-SZH AIO-SYST-04-305-333-SZH AIO-SYST-04-400-500-SZH AIO-SYST-06-465-SZH AIO-SYST-20-475-695-SZH INTERMEDIATE CABLE BRACKET in AIO- lifeline system for standing seam roofs (EN 795 C) Mountable on: (Double-) standing seam roofs Material (material thickness): steel (min. 0.5 mm), aluminium (min. 0.7 mm) Width of profile: 410 610 mm Pre-assembled and without roof perforation! Only for use as intermediate cable bracket in AIO-lifeline system! Not suitable for copper roofs use AIO-FALZ-25! INTERMEDIATE CABLE BRACKET in AIO- lifeline system for ZAMBELLI RIB-ROOF SPEED 500 (EN 795 C) Mountable on: system roof ZAMBELLI RIB-ROOF SPEED 500 Material (material thickness): steel (min. 0.63 mm), aluminium (min. 0.7 mm) Width of profile: 410 510 mm Pre-assembled and without roof perforation! Only for use as intermediate cable bracket in AIO-lifeline system! INTERMEDIATE CABLE BRACKET in AIO- lifeline system for system roofs (EN 795 C) Mountable on: system roofs similar to KALZIP, INTERFALZ Material (material thickness): steel (min. 0.5 mm), aluminium (min. 0.7 mm) Width of profile: 305 333 mm or 400 500 mm Pre-assembled and without roof perforation! Only for use as intermediate cable bracket in AIO-lifeline system! INTERMEDIATE CABLE BRACKET in AIO- lifeline system for ZAMBELLI RIB-ROOF 465 (EN 795 C) Mountable on: system roof ZAMBELLI RIB-ROOF 465 Material (material thickness): steel (min. 0.63 mm), aluminium (min. 0.7 mm) Width of profile: 410 510 mm Pre-assembled and without roof perforation! Only for use as intermediate cable bracket in AIO-lifeline system! INTERMEDIATE CABLE BRACKET in AIO- lifeline system for trapezoidal covering sheet (EN 795 C) Mountable on: trapezoidal covering sheet Material: steel, aluminium Material thickness: min. 0.5 mm Width of profile: 475 695 mm distance from cable to raised bead c. 200 mm Fastening set and sealing strips included! (exact dimensions page 57) AIO-FALZ AIO-FALZ-45-640 AIO-FALZ-45-790 AIO-FALZ-25-640 AIO-FALZ-25-790 END-, CORNER POINT in AIO-lifeline system for standing seam roofs (EN 795 C) Mountable on: (Double-) standing seam roofs Material: aluminium, copper, titanium-zinc alloy, stainless steel, galvanised steel, etc. Material thickness: min. 0.6 mm Width of profile: 370 640 mm or 520 790 mm Without roof perforation! INTERMEDIATE BRACKET in AIO-lifeline system for standing seam roofs (EN 795 C) Mountable on: standing seam roofs Material: aluminium, copper, titanium-zinc alloy, stainless steel, galvanised steel, etc. Material thickness: min. 0.6 mm Width of profile: 370 640 mm or 520 790 mm Without roof perforation! Only for use as intermediate cable bracket in AIO-lifeline system! Variable height adjustment up to 50 mm (VL-20-50) to increase the spacing between the lifeline system and the roofing! 16 EXPERTS IN FALL PROTECTION

AIO-Horizontal lifeline systems AIO-SAND Illustration Catalog N Description AIO-SAND-10-A2 AIO-SAND-11-A2 AIO-SAND-12-A2 END-, CORNER AND INTERMEDIATE CABLE BRACKET in AIO-lifeline system for trapezoidal sheet (EN 795 C) Mountable on: trapezoidal sheet Material: steel Material thickness: min. 0.6 mm Width of profile: 250 333.3 mm Base plate dimensions: 360.5 x 415 x 2 mm Use as intermediate bracket, variable height adjustment up to 50 mm (VL-20-50) to increase the spacing between the lifeline system and the roofing! Fastening set and sealing strips for trapezoidal cover included! (exact hole spacings page 57) END-, CORNER AND INTERMEDIATE CABLE BRACKET in AIO-lifeline system for trapezoidal sheet (EN 795 C) Mountable on: trapezoidal sheet Material: steel Material thickness: min. 0.6 mm Width of profile: 277.5 414 mm Base plate dimensions: 389 x 430 x 2 mm Use as intermediate bracket, variable height adjustment up to 50 mm (VL-20-50) to increase the spacing between the lifeline system and the roofing! Fastening set and sealing strips for trapezoidal cover included! (exact hole spacings page 57) END-, CORNER AND INTERMEDIATE CABLE BRACKET in AIO-lifeline system for trapezoidal sheet (EN 795 C) Mountable on: trapezoidal sheet Material: aluminium Material thickness: min. 0.7 mm Width of profile: 250 333.3 mm Base plate dimensions: 360.5 x 415 x 2 mm Use as intermediate bracket, variable height adjustment up to 50 mm (VL-20-50) to increase the spacing between the lifeline system and the roofing! Fastening set and sealing strips for trapezoidal cover included! (exact hole spacings page 57) AIO-VARIO AIO-VARIO-40 AIO-VARIO-20 END-, CORNER POINT in AIO-lifeline system, self-supporting (EN 795 C-E) Mountable on: flat roofs up to 3 pitch with parapet finish Dimensions: 1675 x 1675 mm Weight: c. 22 kg Final weight: c. 350 kg Filling material: concrete or 12 pcs. of concrete slabs (50 x 50 x 5 cm, 49 x 49 x 5 cm) or 16 pcs. of concrete slabs (50 x 50 x 3.8 cm) Without roof perforation! Concrete, concrete slabs not included! INTERMEDIATE ANCHOR POINT in AIO-lifeline system, self-supporting (EN 795 C-E) Mountable on: flat roofs up to 3 pitch with parapet finish Dimensions: 1675 x 586 mm Weight: c. 12 kg Final weight: c. 180 kg Filling material: concrete or 6 pcs. of concrete slabs (50 x 50 x 5 cm, 49 x 49 x 5 cm) or 8 pcs. of concrete slabs (50 x 50 x 3.8 cm) Without roof perforation! Variable height adjustment up to 50 mm (VL-20-50) to increase the spacing between the lifeline system and the roofing! Concrete, concrete slabs not included! Product accessories (page 48) ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 17

KIT-Horizontal lifeline systems KIT-system variants overview LIFELINE-KIT LIFELINE-KIT AIO-EDLE-14 LIFELINE-KIT- SZH-10 AIO-EDLE-14 LIFELINE-KIT- SZH-10 LIFELINE-KIT- EDLE-10 LIFELINE-KIT- EDLE-10 LIFELINE-KIT- SZH-10 LIFELINE-KIT- EDLE-10 LIFELINE-KIT- EDLE-10 LIFELINE-KIT- SZH-10 18 EXPERTS IN FALL PROTECTION

KIT-Horizontal lifeline systems LIFELINE-KIT Illustration Catalog N Description LIFELINE-KIT-10 LIFELINE-KIT-15* LIFELINE-KIT-25* PRE-ASSEMBLED HORIZONTAL LIFELINE SYSTEM (EN 795 C) Length: 10 / 15 / 25 m, aluminium (anodised), plastic Package includes: 1 pce. end lock 1 pce. shock absorber Stainless steel cable Quick assembly system all system components are in a single bucket! System is compatible with all AIO-lifeline system components! *LIFELINE-KIT-15/-25 including 1 pce. of LIFELINE-KIT-SZH-10 (intermediate bracket)! Corner and curve elements and intermediate brackets not included! LIFELINE-KIT-EDLE-10 KIT-CORNER ELEMENT, cannot be passed over (EN 795 C) Mountable on: facade or wall Pass-over capability: inside and outside corners Connection: fastening borehole Ø 17mm, aluminium (anodised) Variable angle adjustment with integrated shock absorber! LIFELINE-KIT-SZH-10 KIT-INTERMEDIATE BRACKET, can be passed over (EN 795 C) Mountable on: AIO-STA, AIO-STX, AIO-FALZ, AIO-SAND, AIO-VARIO, AIO-SYST, etc. Connection: thread M16 Suitable for installation on posts can only be passed over with steel carabiner! Hex bolt M16 x 45 mm and hex nut M16 icluded! ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 19

TEMP-Temporary lifeline systems TEMP-system variants overview TEMP-ENDS-10 TEMP-HASPEL TEMP-SZH-10 TEMP-ENDS-10 TEMP-HASPEL TEMP-ENDS-10 TEMP-ENDS-10 TEMP-ENDS-10 TEMP-HASPEL TEMP-ENDS-10 TEMP-SZH-10 BEF-412 BEF-412-1 AIO-STA-10 TEMP-ENDS-10 BEF-412 AIO-SZH-10 AIO-STA-10 BEF-412 BEF-412-1 AIO-STA-10 20 EXPERTS IN FALL PROTECTION

TEMP-Temporary lifeline systems TEMP Illustration Catalog N Description TEMP-ENDS-10 TEMP-SZH-10 TEMPORARY END LOCK SET with integrated shock absorber (EN 795 B-C) Mountable on: steel or concrete beam Application: steel, facade or bridge construction Length of lashing strap: 4 m Material: aluminium (anodised), plastic, galvanised steel complete set for one cable span (PU = 2 pcs.) can be quickly attached or detached at any point of the stainless steel cable (AIO-SEIL-30) can be mounted on steel or concrete beams with lashing straps Stainless steel cable (AIO-SEIL-30) not included! TEMPORARY INTERMEDIATE CABLE BRACKET (EN 795 B-C) Mountable on: steel or concrete beam Application: steel, facade or bridge construction Length of lashing strap: 2.5 m Material: aluminium (anodised), plastic, galvanised steel Can be mounted to steel or concrete beams with lashing straps (PU = 1 pce.) TEMP-HASPEL-10-150 TEMP-HASPEL-10-0 MOBILE CABLE PULLEY, galvanised steel cable drum with brakes for practical roll up of the stainless steel cable (AIO-SEIL-30) TEMP-HASPEL-10-150 incl. stainless steel cable, weight ~ 85 kg! Fastening sets for TEMP BEF-412 STEEL CONSTRUCTION, CLAMPING CONSOLE Flange thickness: 10 up to 40 mm Width of steel beam: 125 415 mm BEF-412-1 STEEL CONSTRUCTION, CLAMPING CONSOLE For creating end points with the temporary horizontal lifeline system (TEMP-ENDS-10)! ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 21

VERT-Vertical lifeline systems VERT-system variants overview VERT-SET-50 fixation on the top VERT-SET-50 fixation at the ladder VERT-GLEIT-50 free to move slider VERT-SZH-50 intermediate bracket VERT-SET-50 fixation on the bottom 22 EXPERTS IN FALL PROTECTION

VERT-Vertical lifeline systems VERT Illustration Catalog N Description VERT-SET-50 VERT-GLEIT-50 VERTICAL COMPLETE SET with integrated shock absorber and cable pretension (EN 353-1) Mountable on: ladders Rung dimensions: max. 45 x 45 mm, Ø 45 mm, aluminium Additional safety fixation on the structure oft the building (VERT-SAFE-50) optionally available! Stainless steel cable (AIO-SEIL-30) not included! (page 12) FREE TO MOVE SLIDER with integrated shock absorber, detachable, curve compatible (EN 353-1:2014), (AISI 316) can be quickly attached or detached at any point of the lifeline system free to move the pass-through elements 1 pce. of triple lock carabiner (EN 362) included! VERT-SZH-50 VERTIKAL-INTERMEDIATE BRACKET, can be passed over (EN 353-1) Mountable on: ladders Rung dimensions: max. 45 x 45 mm, Ø 45 mm Material stainless steel (AISI 304) Distance between intermediate bracket 5 m! VERT-SAFE-50 ADDITIONAL PROTECTION for VERT-SET-50 (EN 353-1) Mountable on: structure Material: aluminium Additional protection to fasten the VERT-SET-50 on the structure of the building! VERT-TYP-50-CZ VERT-TYP-50-DE VERT-TYP-50-DK VERT-TYP-50-EN VERT-TYP-50-ES VERT-TYP-50-FR VERT-TYP-50-HU VERT-TYP-50-IT VERT-TYP-50-NL VERT-TYP-50-PL VERT-TYP-50-PT VERT-TYP-50-RO VERT-TYP-50-SK VERT-TYP-50-SV RATING PLATE (EN 353-1) Dimensions: 3 x 12 cm Material: plastic For sticking on VERT-SET-50! Revision plaque included! CZ = CZECH / DE = GERMAN / DK = DANISH / EN = ENGLISH / ES = SPANISH FR = FRENCH / HU = HUNGARIAN / IT = ITALIAN / NL = DUTCH / PL = POLISH PT = PORTUGUESE / RO = ROMANIAN / SK = SLOVAKIAN / SV = SWEDISH Dimensions for VERT 3 x 1050 NEW! 2 x 50 q 45 50 350 750 5000 5000 ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 23

TAURUS-Rail systems TAURUS-system variants overview TAURUS- RAIL-20 TAURUS- RAIL-10 TAURUS- BEF-30 with STA-10 TAURUS- VB-10 TAURUS- RAIL-30 TAURUS- RAIL-10 TAURUS- EA-10 TAURUS- EA-11 TAURUS- VB-10 TAURUS- AS-10 and AS-20 TAURUS- BEF-90 TAURUS- RAIL-40 TAURUS- RAIL-10 TAURUS-BEF-10 or BEF-20 TAURUS- RAIL-50 TAURUS- VB-10 TAURUS- BEF-30 with STA-10 TAURUS- EA-11 TAURUS- RAIL-30 TAURUS- BEF-90 TAURUS- AS-10 and AS-20 TAURUS- RAIL-10 TAURUS- EA-11 TAURUS-BEF-10 TAURUS-BEF-12 TAURUS-BEF-20 TAURUS-BEF-30 TAURUS-BEF-90 TAURUS-VB-10 TAURUS-EA-10 TAURUS-EA-11 24 EXPERTS IN FALL PROTECTION

TAURUS-Rail systems TAURUS Illustration Catalog N Description TAURUS-BEF-10 TAURUS-BEF-10-VE5 TAURUS-BEF-12 TAURUS-BEF-20 TAURUS-BEF-30 TAURUS-BEF-40 TAURUS-BEF-90 RAIL FASTENER for concrete Mountable on: concrete, facade, steel construction Packaging unit: 1 piece / 5 pieces Material: aluminium for fastening TAURUS-RAIL on concrete, facade and steel construction Fastening accessories not included! (page 49) RAIL FASTENER, steel construction, sliding nut M10 Mountable on: steel construction Packaging unit: 5 pieces for fastening TAURUS-RAIL on steel construction Fastening accessories not included! (page 49) (detailed illustration page 56) RAIL FASTENER for facade Mountable on: concrete, facade Through boreholes: 120 mm For mounting on concrete: 2 pcs. of adhesive anchors Minimum drill depth for concrete: min. 100 mm for fastening TAURUS-RAIL on concrete and facade Fastening accessories not included! (page 49) RAIL FASTENER, fastening angle Mountable on: AIO-STA post for fastening TAURUS-RAIL on AIO-STA post Fastening accessories included! RAIL FASTENER for wood Mountable on: wood (min. 10/12 cm) Material: aluminium for fastening TAURUS-RAIL on wood Fastening accessories included! FASTENING ELEMENT for ladder Mountable on: rung Rung dimension: max. Ø 47 mm for fastening TAURUS-RAIL on ladders Fastening accessories included! TAURUS-GLEIT-H-11 RAIL SLIDER, Horizontal (EN 795 D) Inclination range: +/- 5 rail slider for horizontal usage Suitable for overhead systems! TAURUS-PS-H-11-VE2 GUIDE SCREWS for TAURUS-GLEIT-H-11 Packaging unit: 2 pieces Guide screw for TAURUS-GLEIT-H-11 for fixing the slider during abseiling works! TAURUS-GLEIT-V-20 RAIL SLIDER, Vertical (EN 353-1) Inclination range: +/- 3 Rail slider for vertical usage including shock absorbing element! TAURUS-GLEIT-A-30 RAIL SLIDER, Allround (EN 353-1 / EN 795 D) Rail slider for horizontal and vertical usage including shock absorbing element! ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 25

TAURUS-Rail systems TAURUS Illustration Catalog N Description TAURUS-RAIL-10-3000 TAURUS-RAIL-10-6000 ALUMINIUM RAIL, straight run Length: 3000 / 6000 mm Material: aluminium rail element with a straight run TAURUS-RAIL-20-R320-15 TAURUS-RAIL-20-R320-30 TAURUS-RAIL-20-R320-45 TAURUS-RAIL-20-R320-60 TAURUS-RAIL-20-R320-75 TAURUS RAIL-20-R320-90 RAIL CURVED CORNER, horizontal Inclination: 15 / 30 / 45 / 60 / 75 / 90 Material: aluminium Always install rail fastening (TAURUS-BEF) on the rail curved corner! TAURUS-RAIL-30-R385-90 RAIL ARCH OUTSIDE, 90 Inclination: 90 Material: aluminium rail element for vertical and horizontal (facade) usage Always install rail fastening (TAURUS-BEF) on the rail curved corner! TAURUS-RAIL-40-R385-90 RAIL ARCH INSIDE, 90 Inclination: 90 Material: aluminium rail element for vertical and horizontal (facade) usage Always install rail fastening (TAURUS-BEF) on the rail curved corner! TAURUS-RAIL-50-1700-LI TAURUS-RAIL-50-1700-RE ALUMINIUM RAIL, TORSION Torsion inclination: 90 Length: 1700 mm Material: aluminium rail element with a 90 torsion to left and right left LI right RE TAURUS-TYP-10-CZ TAURUS-TYP-10-DE TAURUS-TYP-10-DK TAURUS-TYP-10-EN TAURUS-TYP-10-ES TAURUS-TYP-10-FR TAURUS-TYP-10-IT TAURUS-TYP-10-LT TAURUS-TYP-10-NL TAURUS-TYP-10-PL TAURUS-TYP-10-PT TAURUS-TYP-10-RO TAURUS-TYP-10-SK TAURUS-TYP-10-SV TAURUS-TYP-10-ZH TAURUS-TYP-20-CZ TAURUS-TYP-20-DE TAURUS-TYP-20-DK TAURUS-TYP-20-EN TAURUS-TYP-20-ES TAURUS-TYP-20-FR TAURUS-TYP-20-IT TAURUS-TYP-20-LT TAURUS-TYP-20-NL TAURUS-TYP-20-PL TAURUS-TYP-20-PT TAURUS-TYP-20-RO TAURUS-TYP-20-SK TAURUS-TYP-20-SV TAURUS-TYP-20-ZH TAURUS RATING PLATE, horizontal (EN 795 D) Dimensions: 160 x 92 mm, plastic for identifying a horizontal rail system Various fastening options! CZ = CZECH / DE = GERMAN / DK = DANISH / EN = ENGLISH / ES = SPANISH FR = FRENCH / IT = ITALIAN / LT = LITUANIAN / NL = DUTCH / PL = POLISH PT = PORTUGUESE / RO = ROMANIAN / SK = SLOVAKIAN / SV = SWEDISH ZH = CHINESE TAURUS RATING PLATE, vertical (EN 353-1) Dimensions: 160 x 92 mm, plastic for identifying a vertical rail system Various fastening options! CZ = CZECH / DE = GERMAN / DK = DANISH / EN = ENGLISH / ES = SPANISH FR = FRENCH / IT = ITALIAN / LT = LITUANIAN / NL = DUTCH / PL = POLISH PT = PORTUGUESE / RO = ROMANIAN / SK = SLOVAKIAN / SV = SWEDISH ZH = CHINESE 26 EXPERTS IN FALL PROTECTION

TAURUS-Rail systems TAURUS Illustration Catalog N Description TAURUS-TYP-30-CZ TAURUS-TYP-30-DE TAURUS-TYP-30-DK TAURUS-TYP-30-EN TAURUS-TYP-30-ES TAURUS-TYP-30-FR TAURUS-TYP-30-IT TAURUS-TYP-30-LT TAURUS-TYP-30-NL TAURUS-TYP-30-PL TAURUS-TYP-30-PT TAURUS-TYP-30-RO TAURUS-TYP-30-SK TAURUS-TYP-30-SV TAURUS-TYP-30-ZH TAURUS-TYP-35-CZ TAURUS-TYP-35-DE TAURUS-TYP-35-DK TAURUS-TYP-35-EN TAURUS-TYP-35-ES TAURUS-TYP-35-FR TAURUS-TYP-35-IT TAURUS-TYP-35-LT TAURUS-TYP-35-NL TAURUS-TYP-35-PL TAURUS-TYP-35-PT TAURUS-TYP-35-RO TAURUS-TYP-35-SK TAURUS-TYP-35-SV TAURUS-TYP-35-ZH TAURUS-EA-10 TAURUS RATING PLATE, all-round (EN 353-1 / EN 795 D) Dimensions: 160 x 92 mm, plastic for identifying an all-round rail system (vertical and horizontal) Various fastening options! CZ = CZECH / DE = GERMAN / DK = DANISH / EN = ENGLISH / ES = SPANISH FR = FRENCH / IT = ITALIAN / LT = LITUANIAN / NL = DUTCH / PL = POLISH PT = PORTUGUESE / RO = ROMANIAN / SK = SLOVAKIAN / SV = SWEDISH ZH = CHINESE TAURUS INFORMATION SIGN (EN 353-1 / EN 795 D) Dimensions: 160 x 92 mm, plastic information sign for an all-round rail system (vertical and horizontal) that is fixed on the transition from vertical to horizontal CZ = CZECH / DE = GERMAN / DK = DANISH / EN = ENGLISH / ES = SPANISH FR = FRENCH / IT = ITALIAN / LT = LITUANIAN / NL = DUTCH / PL = POLISH PT = PORTUGUESE / RO = ROMANIAN / SK = SLOVAKIAN / SV = SWEDISH ZH = CHINESE RAIL END UNIT, fixed no access to the system possible (end of the rail) Fastening accessories included! TAURUS-EA-11 RAIL END UNIT, variable, aluminium To step-in and step-out of TAURUS-GLEIT! Fastening accessories included! TAURUS-VB-10 TAURUS-VB-10-VE5 TAURUS-VB-12 TAURUS-VB-12-VE5 RAIL CONNECTION Packaging unit: 1 piece / 5 pieces Material: aluminium Connecting element for alignment of two TAURUS-RAIL elements Fastening accessories included! RAIL CONNECTION Packaging unit: 2 pieces / 10 pieces for the alignment of two TAURUS-RAIL elements Rail connection must only be used together with TAURUS-BEF-12! TAURUS-AS-10 STABILISATION VERTICAL ELEMENT, TAURUS (EN 353-1), aluminium for the vertical step-out of a ladder TAURUS-AS-20 STABILISATION ELEMENT, TAURUS (EN 353-1), aluminium for the vertical step-over of a ladder TAURUS-AS-10 must be ordered additionally! ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 27

BARRIER-Guardrail systems BARRIER-system variants overview BARRIER-R91 BARRIER-V12 BARRIER-V10 BARRIER-R21 BARRIER-R11 BARRIER-R30 BARRIER-R50 BARRIER-V91 BARRIER-R11 BARRIER-R30 BARRIER-T20 BARRIER-S10 BARRIER- T23 BARRIER-V10 / BARRIER-V81 BARRIER-VARIO SIDE PROTECTION SYSTEM held by deadweight load Mountable on: flat roofs (max. 10 pitch) System pitch (preassembled): 90, 75 Without roof perforation parapet of at least 50 mm required! Preassembled bracket with post, plastic-encased concretecounterweight (c. 25 kg) with carrying handles! For parapets < 150 mm, an additional toe board (expansion element) is required! BARRIER-ATTIKA-SEITLICH SIDE PROTECTION SYSTEM inside or outside of parapet Mountable on: parapet (inside or outside) System pitch: 90, 75, 60 BARRIER-ATTIKA-SEITLICH (KLAPPBAR) SIDE PROTECTION SYSTEM inside of parapet (fold-away) Mountable on: parapet (inside) System pitch: 0, 90 system can be folded away (while not in use!) This model is available in segments of up to 3 m (2 posts required per segment!) No connection of the individual segments necessary! (No door element can be built into this system.) BARRIER-ATTIKA-OBEN SIDE PROTECTION SYSTEM top of parapet Mountable on: parapet (top) System pitch: 90 For parapets < 150 mm, an additional toe board (expansion element) is required! BARRIER-DACH SIDE PROTECTION SYSTEM roof Mountable on: roof System pitch: 90 For parapets < 150 mm, an additional toe board (expansion element) is required! 28 EXPERTS IN FALL PROTECTION

BARRIER-Guardrail systems BARRIER Illustration Catalog N Description NEW! BARRIER-A10 BARRIER-A11 BARRIER-A21 BARRIER-A31 BARRIER-D81 ADAPTER on the side of the parapet Mountable on: concrete, steel construction System pitch: 90, 75, 60 for fastening the post BARRIER-S13 to the inside of the parapet Fastening set not included! (page 49) ADAPTER on the side of the parapet, foldable Mountable on: concrete, steel construction System pitch: 90, foldable for fastening the post BARRIER-S13 to the inside of the parapet Fastening set not included! (page 49) ADAPTER on the top of the parapet Mountable on: concrete, steel construction Effective height: 135 mm for fastening the post BARRIER-S13 to the top of the parapet Fastening set not included! (page 49) SPACER BRACKET for parapet Mountable on: concrete, steel construction 2 different adjustment ranges (65 mm 105 mm or 100 mm 145 mm) for BARRIER-A10 and BARRIER-A11 Fastening accessories for BARRIER-A10 / -A11 included! Fastening accessories for parapet not included! (page 49) ADAPTER for AIO-STA post Mountable on: AIO-STA post for fastening of the post BARRIER-S13 on an AIO-STA post Fastening accessories included! BARRIER-F20 BARRIER-F21 TOE BOARD Height x width x length: 170 x 20 x 3000 mm Material: aluminium for BARRIER-S11/S12 and VARIO-adapter BARRIER-V12 For use if no parapet is available that is not higher than 150 mm! Fastening accessories (BARRIER-F21/-F22/-F23) not included! TOE BOARD BRACKET for fastening the toe board to the post BARRIER-S13 Height x width: 25 x 45 mm Packaging unit: 2 pieces for fastening the toe board BARRIER-F20 to the post BARRIER-S13 BARRIER-F22 TOE BOARD BRACKET for fastening the toe board to the VARIO-foot unit BARRIER-V12 for fastening the toe board BARRIER-F20 to the VARIO-foot unit BARRIER-V12 BARRIER-F23 TOE BOARD CONNECTOR SET Packaging unit: 2 pieces for connecting two toe boards BARRIER-F20 ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 29

BARRIER-Guardrail systems BARRIER Illustration Catalog Nr. Description BARRIER-R11 ALUMINIUM PIPE, straight Diameter x wall thickness x length: 35 x 2 x 3000 mm Material: aluminium BARRIER-R21 BARRIER-R30 BARRIER-R40 BARRIER-R50 LINEAR TIE for connecting two rail pipes BARRIER-R11 CORNER TIE Material: aluminium, plastic for creating a corner of 2 rail pipes BARRIER-R11 Angle free adjustable! WALL TIES Mountable on: concrete, steel construction Material: aluminium, plastic Angle free adjustable! Fastening accessories not included! (page 49) END SEAL Material: aluminium, plastic end seal of two rail pipes BARRIER-R11 Projection of the rail pipe max. 500 mm! BARRIER-R91 BARRIER-S11-1080 END CAP for BARRIER-R11 Diameter: 36 mm Packaging unit: 2 pieces Material: plastic end cap for rail pipe BARRIER-R11 Projection of the rail pipe max. 350 mm! POST, system VARIO, straight, fastened Length: 1080 mm Material: aluminium BARRIER-S12-1150 BARRIER-S13-1050 BOOM Length: 1150 mm Material: aluminium standard length for VARIO system, escape route as per plans Special lengths upon request! POST, straight, fastened Length: 1050 mm Material: aluminium BARRIER-T20 BARRIER-T23 DOOR SET Material: aluminium opening selectable up to 800 mm max. For load-bearing implementation, 2 x BARRIER-V10 weights required for each door side! Fastening accessories included! BARRIER-R11 not included! SIDE BAR Length x width x height:565 x 45 x 25 mm Material: aluminium side bar for BARRIER-R11 pipe Projection of pipe max. 500 mm! Fastening accessories included! End caps BARRIER-R91 not included! 30 EXPERTS IN FALL PROTECTION

BARRIER-Guardrail systems BARRIER Illustration Catalog Nr. Description BARRIER-V10 BARRIER-V12 VARIO-WEIGHT Height x width x length: 122 x 395 x 395 mm Weight: 25 kg Material: plastic, concrete plastic-coated concrete weight for foot unit BARRIER-V12 VARIO-FOOT UNIT VARIO foot unit without boom/post, for creation of a load-bearing collective side protection BARRIER-V81 VARIO-ADAPTER FOOT Application: creation of a skylight fencing of max. 2000 x 2000 mm for fastening the post BARRIER-S13 to a VARIO-weight BARRIER-V10 BARRIER-V91 VARIO-CORNER TIE for rectangular connection of two brackets of BARRIER-S12 BARRIER-Z11-DE BARRIER-Z11-DK BARRIER-Z11-EN BARRIER-Z11-ES BARRIER-Z11-FR BARRIER-Z11-IT BARRIER-Z11-NL BARRIER-Z31 RATING PLATE for BARRIER (EN 13374 / EN ISO 14122-3) DE = GERMAN / DK = DANISH / EN = ENGLISH ES = SPANISH / FR = FRENCH / IT = ITALIAN NL = DUTCH FLAME-SCARF ANGLE for BARRIER-V10 Material: aluminium Packaging unit: 1 piece for holding a VARIO-weight BARRIER-V10 in position Per BARRIER-V10 min. 2 pieces of BARRIER-Z31 required! BARRIER-Z33-250 UNDERLAY MAT for BARRIER-V12 Height x width x length: 3 x 250 x 250 mm Material: Polyurethane Packing unit: 1 items underlay mat for one VARIO-BARRIER-V12 foot unit BARRIER-Z50-3000 FOOTWAY RAIL for emergency escape routes Height x width x length: 50 x 80 x 3000 mm Application: emergency escape routes Material: aluminium for the creation of emergency escape routes using concrete slabs BARRIER-Z90 DRILLING JIG for BARRIER-S13 / -V12 for true to size drilling of the clearance holes when shortening the post BARRIER-S13 / -V12 BARRIER-Z91 INSTALLATION TOOL for BARRIER 1 x magnetic nut SW 10 mm and 13 mm for chuck adapter 1 x open-end box wrench SW 13 mm 1 x allen key SW 4 mm with power ball head 1 x pipe cutter with deburrer ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 31

LIGHT-Skylight protection systems LIGHT-Skylight protection systems overview LIGHT LIGHT-V2 LWP-LIGHT 32 EXPERTS IN FALL PROTECTION

LIGHT-Skylight protection systems LIGHT Illustration Catalog N Description LIGHT SKYLIGHT PROTECTION SYSTEM (EN 1263-1) Mesh width: max. 100 x 100 mm high light and smoke permeability easy installation and backfitting For sizes < 1 m², 1 m² will be charged! Each order must contain the inner clearance (L) and the frame profile of the skylight! Size surcharge of EURO 60.00 per size unit and transport costs on a time and material basis! Different RAL colours, other mesh width and special shapes (round, e.g.) on request! (see illustration on page 57) L IGH T-V2 LIGHT-V2-GITTERMATTE-800-800-VZ LIGHT-V2-GITTERMATTE-1000-1000-VZ LIGHT-V2-GITTERMATTE-1300-800-VZ LIGHT-V2-GITTERMATTE-1300-1300-VZ LIGHT-V2-GITTERMATTE-2200-1000-VZ SKYLIGHT PROTECTION SYSTEM (EN 1263-1) Mesh width: max. 60 x 100 mm high light and smoke permeability easy installation and backfitting Standard sizes on stock! Amount of shock absorbers at least required: 800 x 800 / 1000 x 1000 = 8 pcs. 1300 x 800 = 10 pcs. 1300 x 1300 / 2200 x 1000 = 12 pcs. Fastening sets for LIGHT-V2 LIGHT-V2-LIPPE-<3-DAEMPFER-SET FASTENING SET for LIGHT-V2 (water nose 3 mm) Length: 240 mm Packaging unit: 8 pieces Fastening screws and rating plate included! LIGHT-V2-LIPPE->3-DAEMPFER-SET BEFESTIGUNGSSET für LIGHT-V2 (Dichtlippe > 3 mm) Length: 240 mm Packaging unit: 8 pieces Fastening screws and rating plate included! LWP-LIGHT LWP-LIGHT SKYLIGHT PROTECTION SYSTEM for translucent corrugated sheets (EN 1263-1) Mesh width: max. 100 x 100 mm high light and smoke permeability easy installation and backfitting transport costs on a time and material basis! Different RAL colours and special sizes upon request! NEW! MOBI EAP-MOBI-2000-2000 EAP-MOBI-3000-3000 MOBILE SKYLIGHT PROTECTION SYSTEM (EN 1263-1) including single anchor point (EN 795 B) Sizes: 2 x 2 m (max. skylight size 1.5 x 1.5 m) 3 x 3 m (max. skylight size 2.7 x 2.7 m) Material: plastic, galvanised steel mesh net for covering the skylight inlcuding lashing strap (Lashing strap can be also used as single anchor point!) No oversizes possible! Mandatory inspection of the test threads see Services! ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 33

SDH / DAS-Safety roof hooks SDH / DAS-Safety roof hooks overview SDH-02 DAS-21 34 EXPERTS IN FALL PROTECTION

SDH / DAS-Safety roof hooks SDH Illustration Catalog N Description Color SDH-02-ST-1 SDH-02-ST-10 SDH-02-ST-A-1 SDH-02-ST-A-10 SDH-02-ST-B-1 SDH-02-ST-B-10 SDH-02-ST-R-1 SDH-02-ST-R-10 SAFETY ROOF HOOK for quick installation (EN 517 B) Mountable on: wood (min. 8/8 cm) (coated) Min. penetration into static load-bearing construction is 80 mm! 2 x hot-dip galvanised screws (8 x 220 mm) included! grey (RAL 7004) anthracite (RAL 7021) brown (RAL 8017) red (RAL 8004) DAS DAS-21-A2-1 DAS-21-A2-10 DAS-21-A2-A DAS-21-A2-B DAS-21-A2-R SAFETY ROOF HOOK with cable sling (EN 517 B) Mountable on: wood (min. 5/10 cm or 8/5 when installed under counter batten) Cable length: 1 m 4 x hot-dip galvanised nails included! (5 x 150 mm, min. 3 grooves) NEW! nature coloured anthracite (RAL 7021) brown (RAL 8217) red (RAL 8004) Accessories for DAS-21 ADK-105 CAP for cable lead-through on cold roofs Dimensions: Ø 105 mm Material: plastic black ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 35

FSG / FAS-Window safety railings FSG / FAS-Window safety railings overview FSG FAS 36 EXPERTS IN FALL PROTECTION

FSG / FAS-Window safety railings FSG Illustration Catalog N Description Accessories for FSG FSG-01-PROFI WINDOW SAFETY RAILING (EN 12811-1 / EN HD 1000) Adjustable range: 400 910 mm Weight: 5 kg, plastic Telescoping frame! FSG-02-PROFI WINDOW SAFETY RAILING (EN 12811-1 / EN HD 1000) Adjustable range: 770 1720 mm Weight: 7 kg, plastic Telescoping frame! FSG-03 WINDOW SAFETY RAILING (EN 12811-1 / EN HD 1000) Adjustable range: 490 730 mm Weight: 4.6 kg, plastic FSG-04 WINDOW SAFETY RAILING (EN 12811-1 / EN HD 1000) Adjustable range: 700 1160 mm Weight: 5 kg, plastic FSG-05 WINDOW SAFETY RAILING (EN 12811-1 / EN HD 1000) Adjustable range: 1100 1570 mm Weight: 5.9 kg, plastic FSG-SCHUTZKAPPE REPLACEMENT PROTECTIVE CAP for FSG-01 to FSG-05 Packaging unit: 1 piece Material: plastic FAS Accessories for FAS FAS-01 FALL PREVENTION SYSTEM FOR WINDOWS (EN 12811-1 / EN HD 1000) Adjustable range: 390 620 mm Weight: 1.1 kg, plastic FAS-02 FALL PREVENTION SYSTEM FOR WINDOWS (EN 12811-1 / EN HD 1000) Adjustable range: 615 1115 mm und 1115 1610 mm Weight: 3.2 kg, plastic 2 x FAS-guide rods included! FAS-03 FALL PREVENTION SYSTEM FOR WINDOWS (EN 12811-1 / EN HD 1000) Adjustable range: 1550 2400 mm Weight: 5.3 kg, plastic FH-S-R FH-S-W FH-S-R-1000 FH-S-W-1000 FH-B-R FH-B-W SB-12 GUIDE BUSH, TYPE-S Colour: red / white Packaging unit: 1 piece / 1000 pieces Material: plastic for usage for all standard window profiles GUIDE BUSH, TYPE-B Colour: red / white Packaging unit: 1 piece Material: plastic for hollow cavity and centre spar profiles Threaded joint necessary! STEP DRILL BIT, Ø 6-12 mm Material: HSS-steel for guide bush installation, for a ground joint ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 37

EAP-Single anchor points EAP-STABIL Illustration Catalog N Description EAP-STABIL-10-300 EAP-STABIL-10-400 EAP-STABIL-10-500 EAP-STABIL-10-600 SINGLE ANCHOR POINT-STANDARD POST with rotating anchorage eye (EN 795 A) Mountable on: concrete, wood, trapezoidal sheet, steel construction, etc. Post heights: 300 / 400 / 500 / 600 mm, Ø 48 mm Base plate dimensions: 150 x 150 x 8 mm, stainless steel (AISI 304) Thermal insulation cap and sealing sleeve see Product accessories (page 48) Fastening set not included! (see below) Fastening sets for EAP-STABIL-10 BEF-104-A4 CONCRETE (min. C20/25) cracked and uncracked Material: stainless steel (AISI 316) Package: 4 x anchor bolts FISCHER FAZ II 12/10 A4 Drill depth min. 105 mm (Ø 12 mm)! BEF-201 WOOD TIMBER RAFTER (min. 16 x 16 cm) Package: 8 x fastening bolts (8 x 140 mm) 8 x washer (coniform) Min. penetration into static load-bearing construction: 100 mm! BEF-203 BEF-206 BEF-303 BEF-303-1 BEF-303-3 BEF-401-10 WOOD STEEP ROOF, TIMBER RAFTER (min. 8 x 10 cm) Package: 1 x steep roof fastening bar (1250 x 195 x 35 mm) 8 x fastening bolts (8 x 220 mm) (includes fastening accessories for post installation) Min. penetration into static load-bearing construction: 90 mm! WOOD RIDGE INSTALLATION, TIMBER RAFTER (min. 8 x 8 cm) Wood cross-section of load-bearing wood min. 80 x 80 mm, strength of panelling 20 mm! Min. penetration into static load-bearing construction: 80 mm! For the fixation 12 pcs. fastening bolts are required. Fastening material not included! (page 49) TRAPEZOIDAL SUPPORTING SHEET, FASTENING FRAME Dimensions: 840 x 840 x 40 mm Sheet metal thickness: min. 0.6 mm for optimal load distribution on trapezoidal supporting sheet, widely varied useability Fastening set (BEF-303-1 / BEF-303-3) not included! (see below) TRAPEZOIDAL SUPPORTING SHEET, QUICK FASTENING BRACKET Package: 4 x fastening bracket 16 x bore fastener Sheet metal thickness: min. 0.6 mm Raised bead width: min. 60 mm (exact dimensions page 57) TRAPEZOIDAL SUPPORTING SHEET, SPECIAL TOGGLE FASTENER Package: 4 x special toggle fastener Sheet metal thickness: min. 0.6 mm Raised bead width: max. 60 mm Free space under raised bead min. 115 mm, bore diameter Ø 28 mm (exact dimensions page 57) STEEL CONSTRUCTION, COUNTER PLATE (150 x 150 x 8 mm) Max. width of steel construction: 105 mm Fastening accessories not included! (page 49) NEW! 38 EXPERTS IN FALL PROTECTION

EAP-Single anchor points Fastening sets for EAP-STABIL-10 Illustration Catalog N Description BEF-403 BEF-412 STEEL CONSTRUCTION, COUNTER PLATE (140 x 20 x 10 mm) Packaging unit: 2 pieces Max. width of steel construction: 105 mm Fastening accessories not included! (page 49) STEEL CONSTRUCTION, CLAMPING CONSOLE Flange thickness: 10 up to 40 mm Width of steel beam: 125 415 mm E A P-ST X-10 EAP-STX-10-100-250 SINGLE ANCHOR POINT-STANDARD POST with rotating anchorage eye for quick installation (EN 795 A) Mountable on: trapezoidal sheet Material: steel Material thickness (without coating): min. 0.75 mm Insulation thickness: 100 250 mm Post height over aquifer c. 200 mm Material: coated steel (RAL 9005), aluminium, stainless steel (AISI 304) After installation the post has to be sealed in professionally! Fastening material (4 pcs. bore fastener per post, see below) and installation tool (page 51) not included! Fastening sets for STX-10 BBF-4,8-160-0-VZ BBF-4,8-200-0-VZ BBF-4,8-240-0-VZ BBF-4,8-280-0-VZ bore fastener, hexagonal A/F8, Ø 4.8 x 160, IR2, galvanised for insulation thickness of 100 140 mm, galvanised bore fastener, hexagonal A/F8, Ø 4.8 x 200, IR2, galvanised for insulation thickness of 135 180 mm, galvanised bore fastener, hexagonal A/F8, Ø 4.8 x 240, IR2, galvanised for insulation thickness of 175 220 mm, galvanised bore fastener, hexagonal A/F8, Ø 4.8 x 280, IR2, galvanised for insulation thickness of 215 250 mm, galvanised EAP-SLING EAP-SLING-10 EAP-SLING-10-10 STEEP ROOF SLING for steep roofs (EN 795 A) Mountable on: wood (min. 10/12 cm or 8/8 cm + min. 20 mm roof boarding) Cable diameter: Ø 5 mm, stainless steel (AISI 304) Sling length: 400 mm Packaging unit: 1 piece / 10 pieces, stainless steel (AISI 304) Min. penetration into static load-bearing construction is 100 or 80 mm! Order additionally matching fastening bolts, according to the roof system (HBS Ø 8 mm, length= 100 400 mm)! (page 49) (detailed illustration page 56) EAP-POINT EAP-POINT-11-300 EAP-POINT-11-400 EAP-POINT-11-500 EAP-POINT-11-600 SINGLE ANCHOR POINT with rotating anchorage eye (EN 795 A) Mountable on: wood (min. 10/14 cm + min. 19 mm wood boarding or min. 14/14 cm without wood boarding) Post heights: 300 / 400 / 500 / 600 mm, Ø 18 mm Drill hole: Ø 18 mm (drill depth min. 125 mm) EAP-POINT-12-300 EAP-POINT-12-400 EAP-POINT-12-500 EAP-POINT-12-600 SINGLE ANCHOR POINT with rotating anchorage eye (EN 795 A) Mountable on: concrete (min. C16/20) Post heights 300 / 400 / 500 / 600 mm, Ø 18 mm Drill hole: Ø 18 mm (drill depth min. 130 mm) quick installation with specified torque Ideal for annual inspection! ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 39

EAP-Single anchor points EAP-POINT Abbildung Bestell-Nr. Beschreibung EAP-POINT-13-300-A2 EAP-POINT-13-400-A2 EAP-POINT-13-500-A2 EAP-POINT-13-600-A2 EAP-POINT-15-300-A2 EAP-POINT-15-400-A2 EAP-POINT-15-500-A2 EAP-POINT-15-600-A2 SINGLE ANCHOR POINT with rotating anchorage eye (EN 795 A) Mountable on: concrete (min. C20/25) Post heights: 300 / 400 / 500 / 600 mm, Ø 16 mm Drill hole: Ø 18 mm (drill depth min. 120 mm) For bounding in concrete: BEF-110, FISCHER FIS SB 390 S, HILTI HY 200 or HILTI HVU-TZ M16 Fastening set not included! (see below) SINGLE ANCHOR POINT with rotating anchorage eye (EN 795 A, DIBt) Mountable on: concrete (min. C20/25), steel Post heights: 300 / 400 / 500 / 600 mm, Ø 16 mm Drill hole: Ø 18 mm (drill depth min. 100 mm) For bounding in concrete: FISCHER FIS SB 390 S Fastening set not included! NEW! Fastening sets for EAP-POINT-13 BEF-110 CONCRETE (min. C20/25) Package: 1 x hammer capsule, FISCHER-Superbond-System Drill depth 120 mm (Ø 18 mm)! EAP-QUAD-10 EAP-QUAD-10-300 EAP-QUAD-10-400 EAP-QUAD-10-500 EAP-QUAD-10-600 EAP-QUAD-10-300-10 EAP-QUAD-10-400-10 EAP-QUAD-10-500-10 EAP-QUAD-10-600-10 SINGLE ANCHOR POINT with rotating anchorage eye (EN 795 A) Mountable on: concrete, wood, trapezoidal sheet, steel construction Post heights: 300 / 400 / 500 / 600 mm, Ø 16 mm Base plate dimensions: 150 x 150 x 5 mm Packaging unit: 1 piece / 10 pieces Fastening set not included! (see below) Fastening sets for EAP-QUAD-10 BEF-104-A4 CONCRETE (min. C20/25) cracked and uncracked Material: stainless steel (AISI 316) Package: 4 x anchor bolts FISCHER FAZ II 12/10 A4 Drill depth min. 105 mm (Ø 12 mm)! BEF-204 WOOD TIMBER RAFTER (min. 16 x 16 cm) Package: 4 x fastening bolts (8 x 120 mm) 4 x washers (coniform) Min. penetration into static load-bearing construction is 110 mm! BEF-303 BEF-303-1 TRAPEZOIDAL SUPPORTING SHEET, FASTENING FRAME Dimensions: 840 x 840 x 40 mm Sheet metal thickness: min. 0.6 mm for optimal load distribution on trapezoidal supporting sheet, widely varied useability Fastening set (BEF-303-1 / BEF-303-3) not included! (page 41) NEW! TRAPEZOIDAL SUPPORTING SHEET, QUICK FASTENING BRACKET Package: 4 x fastening bracket 16 x bore fastener Sheet metal thickness: min. 0.6 mm Raised bead width: min. 60 mm (exact dimensions page 57) 40 EXPERTS IN FALL PROTECTION

EAP-Single anchor points Fastening sets for EAP-QUAD-10 Illustration Catalog Nr. Description BEF-303-3 BEF-401-10 BEF-403 TRAPEZOIDAL SUPPORTING SHEET, SPECIAL TOGGLE FASTENER Package: 4 x special toggle fastener Sheet metal thickness: min. 0.6 mm Raised bead width: max. 60 mm Free space under raised bead min. 115 mm, bore diameter Ø 28 mm (exact dimensions page 57) STEEL CONSTRUCTION, COUNTER PLATE (150 x 150 x 8 mm) Max. width of steel construction: 105 mm Fastening accessories not included! (page 49) STEEL CONSTRUCTION, COUNTER PLATE (140 x 20 x 10 mm) Packaging unit: 2 pieces Max. width of steel construction: 105 mm Fastening accessories not included! (page 49) EAP-QUAD-11 EAP-QUAD-11-300 EAP-QUAD-11-400 EAP-QUAD-11-500 EAP-QUAD-11-600 SINGLE ANCHOR POINT with rotating anchorage eye (EN 795 A) Mountable on: concrete, wood, trapezoidal sheet, steel construction Post heights: 300 / 400 / 500 / 600 mm, Ø 16 mm Base plate dimensions: 235 x 235 x 4 mm Fastening sets not included! (see below) Fastening sets for EAP-QUAD-11 BEF-103 CONCRETE (min. C20/25) / HOLLOW CONCRETE SLAB (min. C50-60, B4) Package: 4 x screw-in anchor HILTI HUS-H 8 x 55 mm Drill depth on concrete min. 60 mm (Ø 8 mm), Hollow slab cross section (concrete thickness) min. 35 mm! BEF-205 BEF-501-A2 WOOD SANDWICH STRUCTURED COMPOSITE Package: 4 x fastening bolts (8 x 120 mm) 8 x fastening bolts (6 x 40 mm) Wood cross-section of load-bearing wood min. 80 x 100 mm, strength of panelling 20 mm! Min. penetration into static load-bearing construction: 95 mm! TRAPEZOIDAL SUPPORTING SHEET, UNIVERSAL FASTENER Package: 4 x universal fastener Sheet metal thickness: min. 0.75 mm EAP-QUAD-12 EAP-QUAD-12-300 EAP-QUAD-12-400 EAP-QUAD-12-500 EAP-QUAD-12-600 SINGLE ANCHOR POINT with rotating anchorage eye (EN 795 A) Mountable on: trapezoidal sheet Material: steel Material thickness: min. 0.75 mm max. 1.5 mm Post heights: 300 / 400 / 500 / 600 mm, Ø 16 mm Base plate dimensions: 390 x 400 x 2 mm Material: coated steel (RAL 7035), stainless steel (AISI 304) Fastening set included! (exact hole spacings page 56) ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 41

EAP-Single anchor points EAP-QUAD-13 Illustration Catalog N Description EAP-QUAD-13-300 EAP-QUAD-13-400 EAP-QUAD-13-500 EAP-QUAD-13-600 EAP-QUAD-13-300-10 EAP-QUAD-13-400-10 EAP-QUAD-13-500-10 EAP-QUAD-13-600-10 SINGLE ANCHOR POINT with rotating anchorage eye (EN 795 A, DIBt) Mountable on: concrete, trapezoidal sheet Post heights: 300 / 400 / 500 / 600 mm, Ø 16 mm Base plate dimensions: 212 x 212 x 5 mm Packaging unit: 1 piece / 10 pieces Material: coated steel (RAL 7004), stainless steel (AISI 304) Fastening set not included! (exact hole spacings page 56) Fastening sets for EAP-QUAD-13 BEF-104-A4 BEF-307 CONCRETE (min. C20/25) cracked and uncracked Material: stainless steel (AISI 316) Package: 4 x anchor bolts FISCHER FAZ II 12/10 A4 Drill depth min. 105 mm (Ø 12 mm)! TRAPEZOIDAL SUPPORTING SHEET, SPECIAL ANCHOR BOLT, plastic Package: 4 x special anchor bolt Sheet metal thickness: min. 0.63 mm NEW! BEF-502-A2 TRAPEZOIDAL SUPPORTING SHEET, SPECIAL TOGGLE FASTENER Package: 4 x special toggle fastener Sheet metal thickness: min. 0.75 mm EAP-ABP-10 EAP-SPAR EAP-ABP-10-30-A4 SINGLE ANCHOR POINT with rotating abseiling eye (EN 795 A) Mountable on: steel construction, AIO-STA (up to max. 500 mm length), AIO-SYST, AIO-FALZ-45 Thread length to use: 29 mm Thread: M16 (DIN 933, ISO 4017) Material: stainless steel (AISI 316) for abseiling Fastening set included! EAP-SPAR-10-25 SINGLE ANCHOR POINT with rotating (replacement) anchorage eye (EN 795 A) Mountable on: AIO-/EAP STA(BIL), AIO-/EAP-SYST, AIO-/EAP-FALZ-45(-15), AIO-/EAP-SAND, steel construction Thread length to use: 29 mm Thread: M16 (DIN 933, ISO 4017) Not suitable for AIO-/EAP-VARIO, EAP-POINT! Fastening set included! EAP-SPAR-11-50 SINGLE ANCHOR POINT with rotating anchorage eye (EN 795 A) Mountable on: steel construction Thread length to use: 50 mm Thread: M16 Clamping range: 27 mm Drill hole: Ø 17 mm EAP-SPAR-11-125 SINGLE ANCHOR POINT with rotating anchorage eye (EN 795 A) Mountable on: concrete (min. C20/25) Thread length to use: 125 mm Thread: M16 Drill hole: Ø 18 mm (drill depth min. 125 mm) Not suitable for the installation on a flat roof! For bounding in concrete: FISCHER FIS SB 390 or HILTI HY 200 Fastening set not included! 42 EXPERTS IN FALL PROTECTION

EAP-Single anchor points EAP-SPAR Illustration Catalog N Description EAP-SPAR-11-200 EAP-SPAR-11-300 EAP-SPAR-11-400 EAP-SPAR-11-500 SINGLE ANCHOR POINT with rotating anchorage eye (EN 795 A) Mountable on: concrete (min. C20/25), red brick, wood, steel construction Clamping width: clamping width [mm] = thread length to use [mm] minus 110 mm Tread length to use: 200 /300 /400 / 500 mm Thread: M16 Drill hole: Ø 18 mm (drill depth min. 125 mm) Not suitable for installation on flat roof! Fastening set not included! Fastening sets for EAP-SPAR-11 BEF-411 STEEL CONSTRUCTION, CLAMPING CONSOLE Flange thickness: max. 16 mm Width of steel beam: 55 up to 400 mm (exact dimensions page 57) EAP-SPAR-15-125 SINGLE ANCHOR POINT with rotating anchorage eye (EN 795 A, DIBt) Mountable on: concrete (min. C20/25), steel construction Tread length to use: 125 mm Thread: M16 Drill hole: Ø 18 mm (drill depth min. 125 mm) For bounding in concrete: FISCHER FIS SB 390 S Fastening set not included! NEW! EAP-LOCK EAP-LOCK-13 SINGLE ANCHOR POINT-detachable, with rotating anchorage eye (EN 795 A) Mountable on: receptacle sleeve EAP-LOCK-11, aluminium, brass Higher safety through innovative double lock system! EAP-LOCK-11-100 EAP-LOCK-11-150 EAP-LOCK-11-200 EAP-LOCK-11-300 EAP-LOCK-11-400 EAP-LOCK-11-500 EAP-LOCK-12-R EAP-LOCK-12-W RECEPTACLE SLEEVE for EAP-LOCK-13 (EN 795 A) Mountable on: concrete (min. C20/25), red brick, wood, steel construction Thread length to use: 100 / 150 / 200 /300 / 400 / 500 mm Thread: M22 Drill hole: Ø 24 mm (drill depth min. 110 mm) Accessories: 2 pieces of replacement caps in red and white colour with internal thread M10, can be used for pull-out test Also for the usage outside. The product must not be used when the outside is exposed to weather conditions. for bounding in concrete: FISCHER FIS SB 390 or HILTI HY 200 Fastening set not included! Special lengths upon request! REPLACEMENT CAP for EAP-LOCK-11 in red or white colour Material: plastic EAP-FALZ EAP-FALZ-15-640 EAP-FALZ-15-790 SINGLE ANCHOR POINT with rotating anchorage eye for standing seam roofs (EN 795 A) Mountable on: (Double-) standing seam roofs Material: aluminium, copper, titanium-zinc, stainless steel, galvanised steel, etc. Material thickness: min. 0.6 mm Width of profile: 370-640 mm or 520-790 mm Without roof perforation! ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 43

EAP-Single anchor points EAP-SYST Illustration Catalog N Description EAP-SYST-01-410-610 EAP-SYST-02-410-590-P EAP-SYST-03-500-Z EAP-SYST-04-305-333 EAP-SYST-04-400-500 EAP-SYST-06-465-Z EAP-SYST-09-500-Z SINGLE ANCHOR POINT with rotating anchorage eye for standing seam roofs (EN 795 A) Mountable on: (Doublel-) standing seam roofs Material (material thickness): steel (min. 0.5 mm), aluminium (min. 0.7 mm) Width of profile: 410 610 mm Pre-assembled and without roof perforation! Not suitable for copper roofs use EAP-FALZ-15! SINGLE ANCHOR POINT with rotating anchorage eye for PREFA-standing seam roofs (EN 795 A) Mountable on: PREFA-system roofs Material (material thickness): aluminium (min. 0.7 mm) Width of profile: 410 590 mm Pre-assembled and without roof perforation! SINGLE ANCHOR POINT with rotating anchorage eye for ZAMBELLI RIB-ROOF Speed 500 (EN 795 A) Mountable on: system roof ZAMBELLI RIB-ROOF Speed 500 Material (material thickness): steel (min. 0.63 mm), aluminium (min. 0.7 mm) Width of profile: 410 510 mm Pre-assembled and without roof perforation! SINGLE ANCHOR POINT with rotating anchorage eye for system roofs (EN 795 A) Mountable on: system roofs similar to INTERFALZ, KALZIP Material (material thickness): steel (min. 0.5 mm), aluminium (min. 0.7 mm) Width of profile: 305 333 mm or 400 500 mm Pre-assembled and without roof perforation! SINGLE ANCHOR POINT with rotating anchorage eye for ZAMBELLI RIB-ROOF 465 (EN 795 A) Mountable on: system roof ZAMBELLI RIB-ROOF 465 Material (material thickness): steel (min. 0.63 mm), aluminium (min. 0.7 mm) Width of profile: 410 510 mm Pre-assembled and without roof perforation! SINGLE ANCHOR POINT with rotating anchorage eye for ZAMBELLI RIB-ROOF EVOLUTION (EN 795 A) Mountable on: system roof ZAMBELLI RIB-ROOF EVOLUTION Material (material thickness): aluminium (min. 0.7 mm) Width of profile: 400 500 mm Pre-assembled and without roof perforation! 44 EXPERTS IN FALL PROTECTION

EAP-Single anchor points EAP-SAND Illustration Catalog N Description EAP-SAND-10-A2 EAP-SAND-11-A2 EAP-SAND-12-A2 SINGLE ANCHOR POINT with rotating anchorage eye for trapezoidal sheet (EN 795 A) Mountable on: trapezoidal sheet Material: steel Material thickness min. 0.6 mm Width of profile: 250 333.3 mm Base plate dimensions: 360.5 x 415 x 2 mm Fastening set and sealing strips included! (exact hole spacings page 57) SINGLE ANCHOR POINT with rotating anchorage eye for trapezoidal sheet (EN 795 A) Mountable on: trapezoidal sheet Material: steel Material thickness: min. 0.6 mm Width of profile: 277.5-414 mm Base plate dimensions: 389 x 430 x 2 mm Fastening set and sealing strips included! (exact hole spacings page 57) SINGLE ANCHOR POINT with rotating anchorage eye for trapezoidal sheet (EN 795 A) Mountable on: trapezoidal sheet Material: aluminium Material thickness: min. 0.6 mm Width of profile: 250 333.3 mm Base plate dimensions: 360.5 x 415 x 2 mm Fastening set and sealing strips included! (exact hole spacings page 57) EAP-VARIO EAP-VARIO-10 SINGLE ANCHOR POINT-SELF SUPPORTING with rotating anchorage eye (EN 795 E) Mountable on: flat roofs up to 3 pitch with parapet Dimensions: 1675 x 1675 x 167 mm Weight: c. 22 kg Final weight: c. 350 kg Can be filled with: concrete or 12 pcs. of concrete slabs (50 x 50 x 5 cm, 49 x 49 x 5 cm) or 16 pcs. of concrete slabs (50 x 50 x 3.8 cm) Without roof perforation! Concrete or concrete slabs not included! EAP-INDUSTRY EAP-INDUSTRY-11 SINGLE ANCHOR POINT-STAINLESS STEEL CLAMP for metal roof systems (EN 795 A) Mountable on: metal roof systems similar to INTERFALZ, KALZIP Material thickness: min. 1 mm Without roof perforation! Not suitable for standing seam coverings! ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 45

PSA-Personal protective equipment PSA-STRING Illustration Catalog N Description PSA-STRING-1/M PSA-STRING-1/L SAFETY HARNESS (EN 358 / EN 361) Sizes: M (height < 1.8 m and/or < 1 m midsection circumference) L (height > 1.8 m and/or > 1 m midsection circumference) extendible basic safety harness (< 1kg) with automatic buckler in a bag PSA-STRING-2 LANYARD (EN 354) Length: 470 mm extension for PSA-STRING-1 (for work on a steep roof e.g.) 2 pieces of TRIPLE-LOCK carabiner (aluminium) included! PSA-STRING-3/M PSA-STRING-3/L PSA-STRING-4 RESTRAINT AND POSITIONING HARNESS for PSA-STRING-1 (EN 358) Sizes: M (wearer height < 1.8 m and/or < 1 m midsection circumference) L (height > 1.8 m and/or > 1 m midsection circumference) extension for PSA-STRING-1 for additional use as hip harness for restraint and positioning work (EN 363) SHOULDER PAD for PSA-STRING-1 Detachable shoulder pad for additional comfort while wearing the safety harness PSA-STRING-1 PSA-STRING-5 SEAT BOARD for PSA-STRING-1 extension for safety harness PSA-STRING-1 for the usage while working suspended by cable PSA-SET PSA-SET-BASIC/M PSA-SET-BASIC/L PSA-SET for universal usage 1 pce. PSA-STRING-1, safety harness, size M / L, EN 358 / EN 361 1 pce. PSA-BRAKE-10, Kernmantle rope (Ø 12 mm) with guided type fall arrester and integrated shock absorber, length 10 m (EN 353-2 / EN 358 / EN 795) 1 pce. PSA-KARI-1, (Triple-Lock-Carabiner, aluminium, EN 362) PSA-SET-DACH/M PSA-SET-DACH/L PSA-SET for work on the roof 1 pce. PSA-STRING-1, safety harness, sizes M / L, EN 358 / EN 361 1 pce. PSA-STRING-2, length 470 mm, EN 354 1 pce. PSA-BRAKE-10, Kernmantle rope (Ø 12 mm) with guided type fall arrester and integrated shock absorber, length 10 m (EN 353-2 / EN 358 / EN 795) 1 pce. PSA-TAPE-80, (band sling, length 0.8 m, EN 354 / EN 566 / EN 795) 1 pce. PSA-KARI-1, (Triple-Lock carabiner, aluminium, EN 362) 2 pcs. KA-TL-10-362-A2, (Triple-Lock carabiner, stainless steel (AISI 304), EN 362) BRAKE PSA-BRAKE-2 PSA-BRAKE-5 PSA-BRAKE-10 PSA-BRAKE-15 PSA-BRAKE-20 PSA-BRAKE-25 KERNMANTLE ROPE (Ø 12 mm) with length adjusting device (EN 353-2 / EN 354 / EN 358 / EN 795) Lengths: 2 / 5 / 10 / 15 / 20 / 25 m PSA-BRAKE-2 without integrated shock absorber for: Restraint system (EN 354) Positioning system (EN 358) off PSA-BRAKE-5 with integrated shock absorber for: Fall arrest system / restraint system (EN 353-2) Positioning system (EN 358) Temporary horizontal lifeline system (EN 795) NEW! 46 EXPERTS IN FALL PROTECTION

PSA-Personal protective equipment SHARK Illustration Catalog N Description PSA-SHARK-2 PSA-SHARK-5 PSA-SHARK-10 PSA-SHARK-15 KERNMANTLE ROPE (Ø 6 mm) with steel core and length adjusting device (EN 353-2 / EN 354 / EN 358 / EN 795) Lengths: 2 / 5 / 10 / 15 m PSA-SHARK-2 without integrated shock absorber: Restraint system (EN 354) Positioning system (EN 358) off PSA-SHARK-5 with integrated shock absorber: Fall arrest system / restraint system (EN 353-2) Positioning system (EN 358) Temporary horizontal lifeline system (EN 795) Edge tested according to pren 354:2008 Annex A und CNB11/P/11.054! KARI PSA-KARI-1 TRIPLE-LOCK CARABINER, aluminium (EN 362) Material: aluminium Load-bearing capacity: 22 kn Closes automatically! KA-TL-10-362-A2 TRIPLE-LOCK CARABINER, stainless steel (EN 362) Load-bearing capacity: 22 kn replacement carabiner for AIO-GLEIT-10 / -13 Closes automatically! TAPE PSA-TAPE-60 PSA-TAPE-80 PSA-TAPE-120 PSA-TAPE-150 PSA-TAPE-200 TAPE SLING (EN 354 / EN 566 / EN 795) Material: polyester (PES) Dimensions: 25 x 2 mm Lengths: 0.6 / 0.8 / 1.2 / 1.5 / 2.0 m Load capacity: 22 kn for creating anchor points (EN 795) for use as mountain climbing equipment (EN 566) for use as lanyard (EN 354) HSG FALL ARREST DEVICE (EN 360) Material case: aluminium, plastic Lanyard: rope (galvanised steel), harness strap (plastic) with carabiner hook and swivel attachment HSG-41-HWPS-3 HSG-41-HWS-6 HSG-41-HWS-9 HSG-41-HWS-12 HSG 41-HWB-3,5 HSG 41-HWPB-9 HSG 41-HWPB-12 wire rope, galvanised, weight 1.9 kg, length 3 m (EN 360) wire rope, galvanised, weight 3.0 kg, length 6 m (EN 360) wire rope, galvanised, weight 3.7 kg, length 9 m (EN 360) wire rope, galvanised, weight 5.4 kg, length 12 m (EN 360) belt strap, weight 1.4 kg, length 3.5 m (EN 360) belt strap, weight 2.3 kg, length 9 m (EN 360) belt strap, weight 3.4 kg, length 12 m (EN 360) PSA-SCHRANK PSA-SCHRANK-W CUPBOARD for PPE, white Material: steel painted white Dimensions: 600 x 400 x 250 mm for handy storage of PPE ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 47

Product accessories ADM-Sealing sleeve Illustration Catalog N Description ADM-33-EB-ZYL ADM-55-EB SEALING SLEEVE with shrink tube, Ø 33 mm Total height: 250 mm Tube diameter: 33 mm Elastomeric bitumen sheeting: Ø 470 mm Material: bitumen, plastic For EAP-POINT and EAP-QUAD! SEALING SLEEVE with shrink tube, Ø 55 mm Total height: 250 mm Tube diameter: 55 mm Elastomeric bitumen sheeting: Ø 470 mm Material: bitumen, plastic For EAP-STABIL and AIO-STA! ISOL-Thermal isolation cap ISOL-16-300 ISOL-50-300 THERMAL ISOLATION CAP, iø 16 mm Height: ~ 300 mm Material: plastic For EAP-POINT and EAP-QUADRAT! THERMAL ISOLATION CAP, iø 50 mm Height: ~ 300 mm Material: plastic For EAP-STABIL and AIO-STA! VL-Extensions VL-10-200 VL-20-50 EXTENSION SLEEVE, Ø 48 mm Extension: up to max. 200 mm For EAP-STABIL and AIO-STA! Must not be used for AIO end- and AIO corner units! EXTENSION SLEEVE, M16 Extension: up to max. 50 mm Must not be used for AIO end- and AIO corner units! Accessories lifeline system AIO-STOP IDENTIFICATION LIFELINE SYSTEM, end of cable span, aluminium, plastic is directly fixed on the cable and indicates it s end Fastening accessories included! INNO-PLAK REVISION PLAQUE, INNOTECH Colour: foil white, font black Packaging unit: 10 pieces Material: plastic SHOCK-10 SHOCK ABSORBER Material: aluminium anodised reduces the forces in the end points of an AIO lifeline systems Enhancement of the cable deflection up to approximately 50 cm! 48 EXPERTS IN FALL PROTECTION

Product accessories BEFZ-Fastening sets Illustration Catalog N Description HBS-8-80-T40-VZ HBS-8-100-T40-VZ HBS-8-120-T40-VZ HBS-8-140-T40-VZ HBS-8-160-T40-VZ HBS-8-180-T40-VZ HBS-8-200-T40-VZ HBS-8-220-T40-VZ HBS-8-320-T40-VZ HBS-8-360-T40-VZ HBS-8-400-T40-VZ BS-M10-0-125-A2 BS-M12-0-125-A2 BS-M16-0-125-A2 KS-M16-0-9021-A2 HF-07-201-010-ST FASTENING BOLTS (Ø 8 mm) for wood substrate Material: galvanised For fitting the respective installation to the substructure! Observe the minimum penetration into the load-bearing construction as specified in the respective instruction manual! Special lengths upon request! WASHER (DIN 125, ISO 7089/7090) without chamfer iø 10.5 mm/m10 WASHER (DIN 125, ISO 7089/7090) without chamfer iø 13 mm/m12 WASHER (DIN 125, ISO 7089/7090) without chamfer iø 17 mm/m16 LARGE DIAMETER WASHER (DIN 9021, ISO 7093) iø 17 mm/m16 WASHER Ø 8.4 mm chipboard/mdf board countersunk screws SKM-M12-0-934-A2 SKM-M16-0-934-A2 SM-M12-0-985-A2 SM-M16-0-985-A2 SKS-M10-20-933-A2 SKS-M10-25-933-A2 SKS-M10-30-933-A2 SKS-M12-40-933-A2 SKS-M12-60-933-A2 SKS-M12-70-933-A2 SKS-M16-60-933-A2 SKS-M16-70-933-A2 GS-M12-1000-976 GS-M16-1000-976 HEX NUT (DIN 934, ISO 4032) with standard thread M12 HEX NUT (DIN 934, ISO 4032) with standard thread M16 LOCK NUT (DIN 985, ISO 7040) M12 LOCK NUT (DIN 985, ISO 7040) M16 HEX BOLT (DIN 933, ISO 4017) with standard thread w/o shaft / M10 x 20 mm HEX BOLT (DIN 933, ISO 4017) with standard thread w/o shaft / M10 x 25 mm HEX BOLT (DIN 933, ISO 4017) with standard thread w/o shaft / M10 x 30 mm HEX BOLT (DIN 933, ISO 4017) with standard thread w/o shaft / M12 x 40 mm HEX BOLT (DIN 933, ISO 4017) with standard thread w/o shaft / M12 x 60 mm HEX BOLT (DIN 933, ISO 4017) with standard thread w/o shaft / M12 x 70 mm HEX BOLT (DIN 933, ISO 4017) with standard thread w/o shaft / M16 x 60 mm HEX BOLT (DIN 933, ISO 4017) with standard thread w/o shaft / M16 x 70 mm THREADED ROD (DIN 976) M12 x 1000 mm THREADED ROD (DIN 976) M16 x 1000 mm ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 49

Installation tools / Installation accessories 50 EXPERTS IN FALL PROTECTION

Installation tools / Installation accessories MONT-Montagetools Illustration Catalog Nr. Description MONT-1 MONT-2 INSTALLATION SET-1 1 x ring spanner set and ratchet set for system installation 1 x cable shears, 1 x plastic mallet 1 x parallel tension clamp, 1 x chain hoist 2 x torque spanner (4 20 Nm, 20 100 mm) 1 x hexagonal long socket (19 mm) 1 x PSA-TAPE-60 Sling (EN 354, EN 795 B, EN 566, EN 1498 C) + different accessories (sockets, bit, elongation, etc.) INSTALLATION SET-2 1 x chain hoist (3 m) up to 250 kg 1 x parallel tension clamp (for Ø 3 9 mm) MONT-M TORQUE SPANNER (20 to 100 Nm) includes 1 x long nut (19 mm) MONT-S CABLE SHEARS for cutting AIO-SEIL (Ø 8 mm) to length MONT-N RIVET PLIERS (set in case) Hand riveter for rivets (3.2 6.4 mm) Threaded nuts (M4 M10) MONT-ANTISEIZE LUBRICANT for stainless steel thread 3 x WEICON Antiseize syringes ASW 10000 (1 ml in 3 ml syringe) MONT-BO-32 HOLE CUTTER (up to Ø 32 mm) MONT-BO-18-250 MONT-BO-18-450 4-BIT HARD METAL HAMMER DRILL SDS-PLUS Ø 18 mm Operating range: 200 mm or 400 mm MONT-FIS-SB-390-S COMPOUND MORTAR 1 x 390ml cartridge (Fischer FIS SB 390 S with styrene-free hybrid mortar) 2 x static mixer for use with EAP-POINT-13, EAP-LOCK, EAP-SPAR, etc. MONT-RBM TUBE BENDING MACHINE with flaring feature maximum bending angle = 90 suitable for special corner sets in the AIO Lifeline system (AIO-EDLE-16, AIO-EDLE-19) Grease the tube using antiseize compound prior to flaring! MONT-STX- DAEMMMATERIALBOHRER MONT-STX- TRAPEZBLECHBOHRER MONT-STX- VORSTECHER INSTALLATION TOOL for STX-10 post Ø 50 mm borer for insulation INSTALLATION TOOL for STX-10 post Ø 40 mm borer for the trapezoidal sheet INSTALLATION TOOL for STX-10 post Ø 4 mm, I = 390 mm to locate the raised bead ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 51

Fastening sets Illustration Catalog Nr. Description BEF-103 CONCRETE (min. C20/25) / HOLLOW CONCRETE SLAB (min. C50-60, B4) Package: 4 x screw-in anchor HILTI HUS-H 8 x 55 mm Product: EAP-QUAD-11 Drill depth on concrete min. 60 mm (Ø 8 mm), Hollow slab cross section (concrete thickness) min. 35 mm! BEF-104-A4 CONCRETE (min. C20/25) cracked and uncracked Material: stainless steel (AISI 316) Package: 4 x anchor bolts FISCHER FAZ II 12 / 10 A4 Product: EAP-STABIL-10 / EAP-QUAD-10 /EAP-QUAD-13 / AIO-STA-10 / AIO-STA-11 / AIO-STA-12 Drill depth min. 105 mm (Ø 12 mm)! BEF-107 HOLLOW CONCRETE SLAB (min. C50/60, B4) Package: 8 x hollow core anchor FISCHER FHY-M10 x 52 8 x hex bolt M10 x 60 (DIN 933) 8 x washer (M10) Product: AIO-STA-12 Hollow slab cross-section (concrete thickness) min. 30 mm! BEF-110 CONCRETE (min. C20/25) Package: 1 x adhesive anchor, FISCHER-Superbond-System Product: EAP-POINT-13 Drill depth 120 mm (Ø 18 mm)! BEF-201 BEF-203 BEF-204 WOOD TIMBER RAFTER (min. 16 x 16 cm) Package: 8 x fastening bolts (8 x 140 mm) 8 x washer (coniform) Product: EAP-STABIL-10 / AIO-STA-10 / AIO-STA-11 Min. penetration into static load-bearing construction is 100 mm! WOOD STEEP ROOF, TIMBER RAFTER (min. 8 x 10 cm) Package: 1 x steep roof fastening bar (1250 x 195 x 35 mm) 8 x fastening bolts (8 x 220 mm) (includes fastening accessories for post installation) Product: EAP-STABIL-10 / AIO-STA-10 / AIO-STA-11 Min. penetration into static load-bearing construction is 90 mm! WOOD TIMBER RAFTER (min. 16 x 16 cm) Package: 4 x fastening bolts (8 x 120 mm) 4 x washers (coniform) Product: EAP-QUAD-10 Min. penetration into static load-bearing construction is 110 mm! BEF-205 BEF-206 BEF-303 BEF-303-1 WOOD SANDWICH STRUCTURED COMPOSITE Package: 4 x fastening bolts (8 x 120 mm) 8 x fastening bolts (6 x 40 mm) Product: EAP-QUAD-11 Wood cross-section of load-bearing wood min. 80 x 100 mm, strength of panelling 20 mm! Min. penetration into static load-bearing construction is 95 mm! WOOD RIDGE INSTALLATION, TIMBER RAFTER (min. 8 x 8 cm) Product: EAP-STABIL-10 / AIO-STA-10 Wood cross-section of load-bearing wood min. 80 x 80 mm, strength of panelling 20 mm! Min. penetration into static load-bearing construction is 80 mm! For the fixation 12 pcs. fastening bolts are required. Fastening material not included! (page 49) TRAPEZOIDAL SUPPORTING SHEET, FASTENING FRAME Dimensions: 840 x 840 x 40 mm Sheet metal thickness: min. 0.6 mm Product: EAP-STABIL-10 / EAP-QUAD-10 / AIO-STA-10 / AIO-STA-11 / AIO-STA-12 for optimal load distribution on trapezoidal supporting sheet, widely varied useability Fastening set (BEF-303-1 / BEF-303-3) not included! NEW! TRAPEZOIDAL SUPPORTING SHEET, QUICK FASTENING BRACKET Package: 4 x fastening bracket 16 x bore fastener Sheet metal thickness: min. 0.6 mm Raised bead width: min. 60 mm Product: BEF-303 (exact dimensions page 57) 52 EXPERTS IN FALL PROTECTION

Fastening sets Illustration Catalog Nr. Description BEF-303-3 BEF-306-VE250 BEF-306-VE50 BEF-307 BEF-401-10 BEF-401-12 BEF-403 BEF-404 BEF-404-1 TRAPEZOIDAL SUPPORTING SHEET, SPECIAL TOGGLE FASTENER Package: 4 x special toggle fastener Sheet metal thickness: min. 0.6 mm Raised bead width: max. 60 mm Product: BEF-303 Free space under raised bead min. 115 mm, bore diameter Ø 28 mm (exact dimensions page 57) TRAPEZOIDAL COVER SHEET / SANDWICH PANEL, sealing rivets Packaging unit: 50 piece / 250 pieces Sheet thickness (aluminium): min. 0.5 mm (without coating) Product: AIO-SAND-12 Metal driller Ø 6,5 mm included! TRAPEZOIDAL SUPPORTING SHEET, SPECIAL ANCHOR BOLT, plastic Package: 4 x special anchor bolt Sheet metal thickness: min. 0.63 mm Product: EAP-QUAD-13 STEEL CONSTRUCTION, COUNTER PLATE (150 x 150 x 8 mm) / (300 x 300 x 8 mm) Max. width of steel construction: 105 mm / 185 mm or 255 mm Product: EAP-STABIL-10 / AIO-STA-10 / AIO-STA-11 / AIO-STA-16 / EAP-QUAD-10 BEF-401-12: AIO-STA-12 Fastening accessories not included! (page 49) STEEL CONSTRUCTION, COUNTER PLATE (140 x 20 x 10 mm) Packaging unit: 2 pieces Max. width of steel construction: 105 mm Product: EAP-STABIL-10 / AIO-STA-10 / AIO-STA-11 / AIO-STA-16 / EAP-QUAD-10 Fastening accessories not included! (page 49) TRAPEZOIDAL SUPPORTING SHEET, SCREW FASTENER Package: 4 x counter plate incl. screw material, sealing washer Sheet metal thickness: min. 0.7 mm Product: AIO-STA-12 Only for limited use in the AIO Lifeline system (BEF-404-1)! TRAPEZOIDAL SUPPORTING SHEET, STABILISATION BAR Package: 2 x support bars 4 x bore fastener 4 x centring washer Sheet metal thickness: min. 0.7 mm Product: BEF-404 Only in combination of BEF-404 to stabilise corner- and end points! NEW! BEF-411 BEF-412 BEF-412-1 BEF-501-A2 BEF-502-A2 STEEL CONSTRUCTION, CLAMPING CONSOLE Flange thickness: max. 16 mm Width of steel beam: 55 up to 400 mm Product: EAP-SPAR-11 (exact dimensions page 57) STEEL CONSTRUCTION, CLAMPING CONSOLE Flange thickness: 10 up to 40 mm Width of steel beam: 125 415 mm Product: EAP-STABIL-10 / AIO-STA-10 / AIO-STA-11 / TEMP-ENDS-10 / TEMP-SZH-10 STEEL CONSTRUCTION, CLAMPING CONSOLE Product: BEF-412 / AIO-STA-10 / TEMP For creating end points with the temporary horizontal lifeline system (TEMP-ENDS-10)! TRAPEZOIDAL SUPPORTING SHEET, UNIVERSAL FASTENER Package: 4 x universal fastener Sheet metal thickness: min. 0.75 mm Product: EAP-QUAD-11 TRAPEZOIDAL SUPPORTING SHEET, SPECIAL TOGGLE FASTENER Package: 4 x special toggle fastener Sheet metal thickness: min. 0.75 mm Product: EAP-QUAD-13 ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 53

Presentation models 54 EXPERTS IN FALL PROTECTION

Presentation models Presentation Models Illustration Catalog Nr. Description VERT-ENDS-11-DEMO VERTICAL PRESENTATION MODEL (Vertical lifeline system) Scale: 1:1 Length: 1.8 m Original components (VERT-ENDS-11) mounted on aluminium ladder without intermediate cable brackets VERT-SZH-12 and VERT-GLEIT-10 AIO-PLUS-DEMO AIO PRESENTATION MODEL (Horizontal lifeline system) Scale: 1:1 AIO-ENDS-10, AIO-SZH-10, AIO-GLEIT-10 mounted on steel construction BARRIER-DEMO BARRIER PRESENTATION MODEL (Safety railing) Scale: 1:1 Presentation case contains all components for the presentation of the BARRIER-side protection system! TAURUS-DEMO TAURUS PRESENTATION MODEL (Rail system) Scale: 1:1 Presentation case contains the most common components for the presentation of TAURUS-rail system! LIGHT-DEMO LIGHT PRESENTATION MODEL (Skylight protection) Scale: 1:1 Dimensions: 360 x 360 mm VARIO-DEMO VARIO PRESENTATION MODEL Scale: 1:3 ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 55

Dimensions / Hole spacings / Drill patterns EAP-QUAD-12 EAP-SLING EAP-QUAD-13 VERT TAURUS BEF-12 t=3-6 mm = M10 x 20 DIN 933 A2 t= 7-11 mm = M10 x 25 DIN 933 A2 t= 12-16 mm = M10 x 30 DIN 933 A2 3 x t > 0,5 13-17 > 1 2 x 50 q 45 50 350 750 5000 5000 1050 56 EXPERTS IN FALL PROTECTION

Dimensions / Hole spacings / Drill patterns AIO-EDLE-19 AIO-SYST-20 / SYST-20-SZH AIO/EAP-SAND-10 /-11 /-12 SAND-10 SAND-11 SAND-12 >12 >12 BEF-303-1 BEF-303-3 BEF-411 LIGHT B max. t=8 t=16 INNOTECH SPAR-11 101 85 TYP-200 201 185 TYP-300 301 285 TYP-400 401 385 TYP-500 N-Skylight dimension M16 >20 B K-Inner clearance K-Ceiling clearance t = 8-16 ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! 57

Notes EXPERTS IN FALL PROTECTION

Notes ATTENTION: Read the latest INNOTECH instructions for installation and usage of the products! www.innotech.at

INNOTECH Arbeitsschutz GmbH Laizing 10, 4656 Kirchham, Austria T: +43 7619 22122-0 F: +43 7619 22122-147 E-mail: office@innotech.at www.innotech.at INNOTECH Arbeitsschutz GmbH Garnisonsring 29, 57072 Siegen, Germany T: +49 271 2341 94-0 F: +49 271 2341 94-250 E-mail: office@innotech.de www.innotech.de INNOTECH Arbeitsschutz AG Seestrasse 14b, 5432 Neuenhof, Switzerland T: +41 56 416 90 40 F: +41 56 416 90 49 E-mail: info@innotechag.ch www.innotechag.ch QR-Code to Product Finder www.innotech.at