BTA6-600BW3G, BTA6-800BW3G, Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to 800 On-State Current Rating of 6 A RMS at 80C Uniform Gate Trigger Currents in Three Quadrants High Immunity to d/dt 500 /µs minimum at 25C Minimizes Snubber Networks for Protection Industry Standard TO-220AB Package Pin Out High Commutating di/dt 4.0 A/ms minimum at 25C Internally Isolated (2500 RMS ) These Devices are Pb Free Functional Diagram CASE 22A STYLE 4 MT2 G 2 Additional Information Datasheet Resources Samples
Maximum Ratings (T J = 25C unless otherwise noted) Rating Symbol alue Unit Peak Repetitive Off-State oltage (Note ) (Gate Open, Sine Wave 50 to 60 Hz, T J = -40 to 25C) BTA6 600BW3G BTA6 800BW3G DRM, RRM 600 800 On-State RMS Current (Full Cycle Sine Wave, 60 Hz, T C = 80C) I T (RMS) 6 A Peak Non-Repetitive Surge Current (One Full Cycle Sine Wave, 60 Hz, T C = 25C) I TSM 70 A Circuit Fusing Consideration (t = 8.3 ms) I 2 t 20 A²sec Non Repetitive Surge Peak Off State oltage (T J = 25C, t = ms) DSM / RSM DSM / RSM +0 Peak Gate Current (T J = 25C, t = 20ms) I GM 4.0 A Peak Gate Power (Pulse Width.0 µs, T C = 80C) P G(A) 20 W Average Gate Power (T J = 25C) P G(A).0 W Operating Junction Temperature Range T J -40 to +25 C Storage Temperature Range T stg -40 to +25 C RMS Isolation oltage (t = 300 ms, R.H. 30%, T A = 25C) iso 2500 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.. DRM and RRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. Thermal Characteristics Rating Symbol alue Unit Thermal Resistance, Junction to Case (AC) Junction to Ambient R 8JC R 8JA 2.5 60 C/W Maximum Lead Temperature for Soldering Purposes, /8 from case for seconds T L 260 C
Electrical Characteristics - OFF (T J = 25C unless otherwise noted ; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit Peak Repetitive Blocking Current T J = 25C ( D = DRM = RRM ; Gate Open) T J = 25C I DRM, I RRM - - 0.005 - - 2.0 ma Electrical Characteristics - ON (T J = 25C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit Forward On-State oltage (Note 2) (I TM = ±22.5 A Peak) TM.55 Gate Trigger Current (Continuous dc) ( D = 2, R L = 30 Ω) 2.5 50 MT2(+), G( ) 2.5 50 I GT ma MT2( ), G( ) 2.5 50 Holding Current ( D = 2, Gate Open, Initiating Current = ±50 ma) 60 ma 70 Latching Current ( D = 2, I G = 50 ma) I L MT2(+), G( ) 90 ma MT2( ), G( ) 70 0.5.7 Gate Trigger oltage ( D = 2, R L = 30 Ω) MT2(+), G( ) 0.5. GT MT2( ), G( ) 0.5. 0.2 Gate Non Trigger oltage (T J = 25C) MT2(+), G( ) 0.2 t gt MT2( ), G( ) 0.2 2. Indicates Pulse Test: Pulse Width 2.0 ms, Duty Cycle 2%.
Dynamic Characteristics Characteristic Symbol Min Typ Max Unit Rate of Change of Commutating Current, See Figure. (Gate Open, T J = 25C, No Snubber) (di/dt)c 4.0 A/ms Critical Rate of Rise of On State Current (T J = 25C, f = 20 Hz, I G = 2 x I GT, tr 0 ns) di/dt 50 A/µs Critical Rate of Rise of Off-State oltage ( D = 0.66 x DRM, Exponential Waveform, Gate Open, T J = 25C) d/dt 500 /µs oltage Current Characteristic of SCR Symbol Parameter +C urrent DRM I DRM RRM Peak Repetitive Forward Off State oltage Peak Forward Blocking Current Peak Repetitive Reverse Off State oltage I RRM at RRM on state TM Quadrant MainTerminal 2 + I RRM Peak Reverse Blocking Current off state + oltage I DRM at DRM TM Maximum On State oltage Holding Current Quadrant 3 MainTerminal 2 TM Quadrant Definitions for a Triac MT2 POSITIE (Positive Half Cycle) + (+) MT2 (+) MT2 Quadrant II ( ) I GT (+) I GT Quadrant I I GT +I GT ( ) MT2 ( ) MT2 Quadrant III ( ) I GT (+) I GT Quadrant I MT2 NEGATIE (Negative Half Cycle) All polarities are referenced to. With in phase signals (using standard AC lines) quadrants I and III are used.
I Thyristors Figure. RMS Current Derating Figure 2. On-State Power Dissipation Figure 3. On State Characteristics Figure 4. Thermal Response 00 0 r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) 0. 0.0 0. 0 00 4 Figure 5. Hold Current ariation I T 20 0.
I Thyristors Figure 6. Gate Trigger Current ariation Figure 7. Gate Trigger oltage ariation 0 L.6 L.2 0.6 Figure 8. Critical Rate of Rise of Off-State oltage (Exponential Waveform) µ 5000 4K D = 800 pk T J = 25C 3K 2K K 0 0 00 R G, TO MAIN TERMINAL RESISTANCE (OHMS) 000 Figure 9. Simplified Test Circuit to Measure the Critical Rate of Rise of Commutating Current (di/dt) L L N4007 200 RMS ADJUST FOR I TM, 60 Hz AC MEASURE I CHARGE TRIGGER CHARGE CONTROL C L TRIGGER CONTROL N94 5 MT2 G - + 200 Note: Component values are for verification of rated (di/dt) c. See AN48 for additional information. Note: Component values are for verification of rated (di/dt)c. See AN48 for additional information
Dimensions Part Marking System SEATING PLANE 4 B F T C S H Q Z 4 2 3 A K U 2 3 TO 220AB CASE 22A STYLE 2 L R G N D J Dim Inches Millimeters Min Max Min Max A 0.570 0.620 4.48 5.75 B 0.380 0.405 9.66.28 C 0.60 0.90 4.07 4.82 D 0.025 0.035 0.64 0.88 F 0.42 0.47 3.6 3.73 G 0.095 0.5 2.42 2.66 H 0. 0.55 2.80 3.93 J 0.04 0.022 0.36 0.55 K 0.500 0.562 2.70 4.27 L 0.045 0.060.5.52 N 0.90 0.2 4.83 5.33 Q 0.0 0.20 2.54 3.04 R 0.080 0. 2.04 2.79 S 0.045 0.055.5.39 T 0.235 0.255 5.97 6.47 U 0.000 0.050 0.00.27 0.045.5 Z 0.080 2.04 Pin Assignment Main Terminal 2 Main Terminal 2 3 Gate 4 No Connection Ordering Information Device Package Shipping BTA6 600BW3G BTA6 800BW3G TO 220AB (Pb Free) TO 220AB (Pb Free) 50 Units / Rail 50 Units / Rail. DIMENSIONING AND TOLERANCING PER ANSI Y4.5M, 982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics.