EVALUATION KIT AVAILABLE MAX9622 General Description The MAX9622 op amp features rail-to-rail output and MHz GBW at just 1mA supply current. At power-up, this device autocalibrates its input offset voltage to less than 1µV. It operates from a single-supply voltage of 2.V to.2v. The MAX9622 is available in a tiny 2mm x 2mm, -pin SC7 package and is rated over the -4 C to +12 C automotive temperature range. Applications Power Modules ADC Drivers for Industrial Systems Instrumentation Filters Features MHz UGBW Low Input Voltage Offset Voltage (1μV max) Input Common-Mode Voltage Range Extends Below Ground Wide 2.V to.2v Supply Range Low 1mA Supply Current Ordering Information PART TEMP RANGE PIN- PACKAGE +Denotes a lead(pb)-free/rohs-compliant package. T = Tape and reel. TOP MARK MAX9622AXK+T -4 C to +12 C SC7 AUA Typical Application Circuit INPUT.kI.kΩ 4.7nF 14.3kΩ 47pF V CC 2kΩ V CC /2 OUTPUT 2kΩ MAX9622 USING THE MAX9622 AS A LOWPASS BESSEL FILTER (CORNER FREQUENCY = 1kHz). 19-227; Rev 1; 4/1
Absolute Maximum Ratings Supply Voltage (V CC to GND)...-.3V to +.V All Other Pins...(GND -.3V) to (V CC +.3V) Short-Circuit Duration to GND or V CC... 1s Continuous Input Current (any pins)...±2ma Thermal Limits (Note 1) Continuous Power Dissipation (T A = +7 C) -Pin SC7 (derate 3.1mW/ C above +7 C)...24.4mW Operating Temperature Range... -4 C to +12 C Junction Temperature...+1 C Storage Temperature Range... -6 C to +1 C Lead Temperature (soldering, 1s)...+3 C Soldering Temperature (reflow)...+26 C Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD1-7, using a four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Electrical Characteristics (V CC = V, V IN+ = V IN- = V, R L = 1kΩ to V CC /2, T A = -4 C to +12 C, unless otherwise noted. Typical values are at T A = +2 C.) (Note 2) POWER SUPPLY PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Supply Voltage Range V CC Guaranteed by PSRR 2.2 V Supply Current I CC No load Power-Supply Rejection Ratio PSRR T A = +2 C 1 1. -4 C T A +12 C 2.1 T A = +2 C 97 126-4 C T A +12 C 93 Power-Up Time t ON 3 ms DC SPECIFICATIONS After power-up autocalibration 8 1 Input Offset Voltage V OS -4 C T A +12 C 8 3 Input Offset Voltage Drift ΔV OS 3 µv/ C T A = +2 C 62 1 Input Bias Current I B -4 C T A +12 C 32 T A = +2 C 3 12 Input Offset Current I OS -4 C T A +12 C 3 Input Common-Mode Range V CM Guaranteed by CMRR, T A = -4 C to +12 C -.1 V CC -1.3 V Common-Mode Rejection Ratio Large-Signal Gain Output Voltage Swing CMRR A VOL T A = +2 C 87 121-4 C T A +12 C 8 4mV V OUT V CC - 4mV 4mV V OUT V CC - 4mV, R L = 1kΩ to V CC /2 T A = +2 C 91 13-4 C T A +12 C 84 T A = +2 C 77 89-4 C T A +12 C 69 V OH - V CC RL = 1kΩ to V CC /2 6 V OL RL = 1kΩ to GND, T A = +2 C 4 RL = 1kΩ to V CC /2 6 RL = 1kΩ to GND 48 Short-Circuit Current I SC (Note 3) 8 ma ma db µv na na db db mv www.maximintegrated.com Maxim Integrated 2
Electrical Characteristics (continued) (V CC = V, V IN+ = V IN- = V, R L = 1kΩ to V CC /2, T A = -4 C to +12 C, unless otherwise noted. Typical values are at T A = +2 C.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS AC SPECIFICATIONS Gain-Bandwidth Product GBW MHz Large-Signal Bandwidth BW LS V OUT = 2V P-P 3 MHz Slew Rate SR V OUT = 2V P-P, 1% to 9% 2 V/µs Settling Time t S To.1%, V OUT = 2V P-P, C L = 1pF 2 ns Total Harmonic Distortion THD f = 1kHz, V OUT = 2V P-P 9 db Input Voltage-Noise Density e N f = 1kHz 13 nv/ Hz Input Current-Noise Density i N f = 1kHz 3 pa/ Hz Note 2: The device is 1% production tested at T A = +2 C. Temperature limits are guaranteed by design. Note 3: Guaranteed by design. Typical Operating Characteristics (V CC = V, R L = 1kΩ to V CC /2, T A = +2 C, unless otherwise noted.) SUPPLY CURRENT (ma) SUPPLY CURRENT vs. SUPPLY VOLTAGE 1..98.96.94.92.9.88.86.84.82 MAX9622 toc1 QUIESCENT CURRENT (ma) QUIESCENT CURRENT vs. TEMPERATURE 2. 1.8 1.6 1.4 1.2 1..8.6.8.4 2. 2. 3. 3. 4. 4... - -2 2 7 1 12 SUPPLY VOLTAGE (V) MAX9622 toc2 INPUT OFFSET VOLTAGE (µv) 3 2 2 1 1 INPUT OFFSET VOLTAGE vs. COMMON-MODE VOLTAGE -.. 1. 1. 2. 2. 3. 3. 4. COMMON-MODE VOLTAGE (V) MAX9622 toc3 OFFSET VOLTAGE (µv) 2 1 1 - -1-1 OFFSET VOLTAGE vs. TEMPERATURE MAX9622 toc4 INPUT OFFSET VOLTAGE (µv) 1 1 - -1-1 -2-2 V CM = V INPUT OFFSET VOLTAGE vs. SUPPLY VOLTAGE MAX9622 toc OCCURANCE (%) 2 2 1 1 OFFSET VOLTAGE HISTOGRAM MAX9622 toc6-2 - -2 2 7 1 12-3 2. 2. 3. 3. 4. 4... SUPPLY VOLTAGE (V) 1 1 2 2 3 OFFSET VOLTAGE (µv) 3 4 www.maximintegrated.com Maxim Integrated 3
Typical Operating Characteristics (continued) (V CC = V, R L = 1kΩ to V CC /2, T A = +2 C, unless otherwise noted.) OUTPUT HIGH VOLTAGE (mv) OUTPUT HIGH VOLTAGE vs. TEMPERATURE SOURCING CURRENT (V CC - V OUT) 2 1 I SOURCE = ma 1 I SOURCE = 1mA I SOURCE =.1mA I SOURCE =.1mA - -2 2 7 1 12 MAX9622 toc7 OUTPUT LOW VOLTAGE (mv) OUTPUT LOW VOLTAGE vs. TEMPERATURE SINKING CURRENT 16 14 I SINK = ma 12 1 8 I SINK = 1mA I SINK =.1mA 6 4 2 I SINK =.1mA - -2 2 7 1 12 MAX9622 toc8 INPUT BIAS CURRENT (na) INPUT BIAS CURRENT vs. TEMPERATURE 2 IN+ 1 1 IN- - -2 2 7 1 12 MAX9622 toc9 INPUT BIAS CURRENT (na) 2 1 1 INPUT BIAS CURRENT vs. TEMPERATURE IN+ IN- MAX9622 toc1 CMRR (db) -2-4 -6-8 -1 COMMON-MODE REJECTION RATIO vs. FREQUENCY MAX9622 toc11 PSRR (db) -2-4 -6-8 -1 POWER-SUPPLY REJECTION RATIO vs. FREQUENCY MAX9622 toc12 - -2 2 7 1 12-12.1.1 1 1 1 1 1, FREQUENCY (khz) -12.1.1 1 1 1 1 1, FREQUENCY (khz) 4nV/div.1Hz TO 1Hz INPUT VOLTAGE NOISE MAX9622 toc13 INPUT VOLTAGE NOISE (nv/ Hz) INPUT VOLTAGE NOISE vs. FREQUENCY R 4 LOAD = NO LOAD 4 3 3 2 2 1 1 MAX9622 toc14 INPUT CURRENT NOISE (pa/ Hz) INPUT CURRENT NOISE vs. FREQUENCY 16 14 12 1 8 6 4 2 MAX9622 toc1 1s/div 1 1 1 1, FREQUENCY (Hz) 1 1 1 1, FREQUENCY (Hz) www.maximintegrated.com Maxim Integrated 4
Typical Operating Characteristics (continued) (V CC = V, R L = 1kΩ to V CC /2, T A = +2 C, unless otherwise noted.) V CC V/div GND V OUT mv/div GND TURN-ON RESPONSE V IN = 22.34mV, A V = 1V/V MAX9622 toc16 QUIESCENT CURRENT (ma) 2. 1.8 1.6 1.4 1.2 1..8.6 QUIESCENT CURRENT vs. TEMPERATURE V CC = V, V OUT IN SATURATION V OUT = HIGH V OUT = LOW MAX9622 toc17.4 - -2 2 7 1 12 OUTPUT RECOVERY FROM SATURATION V OUT SATURATED TO POSITIVE RAIL MAX9622 toc18 OUTPUT RECOVERY FROM SATURATION V OUT SATURATED TO NEGATIVE RAIL MAX9622 toc19 V OUT 1V/div V OUT 1V/div GND GND 4µs/div 4µs/div THD+N (%) -4 - -6-7 -8-9 -1 TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCY MAX9622 toc2 OPEN-LOOP GAIN (db) 12 1 8 6 4 2 OPEN-LOOP GAIN vs. FREQUENCY MAX9622 toc21-11 -12 1 1 1 1, 1, FREQUENCY (khz) -2.1.1 1 1 1 1 1, 1, FREQUENCY (khz) www.maximintegrated.com Maxim Integrated
Typical Operating Characteristics (continued) (V CC = V, R L = 1kΩ to V CC /2, T A = +2 C, unless otherwise noted.) LARGE-SIGNAL RESPONSE MAX9622 toc22 A V = 1V/V SMALL-SIGNAL RESPONSE MAX9622 toc23 A V = 1V/V OUTPUT OUTPUT mv/div 1µs/div 4µs/div ISOLATION RESISTANCE (Ω) 4 4 3 3 2 2 1 1 CAPACITIVE LOADING STABILITY vs. ISOLATION RESISTANCE, A V = 1V/V STABLE UNSTABLE MAX9622 toc24 LOAD RESISTANCE (Ω) 1, 1 PARALLEL CAPACITIVE LOADING V CC = V UNSTABLE STABLE MAX9622 toc2 1 2 3 4 6 7 8 9 1 CAPACITANCE (pf) 1 7 1 12 1 CAPACITANCE (pf) -2 CROSSTALK vs. FREQUENCY MAX9622 toc26 CROSSTALK (db) -4-6 -8-1 -12-14.1 1 1 1 1 1, 1, FREQUENCY (khz) www.maximintegrated.com Maxim Integrated 6
Pin Configuration TOP VIEW + MAX9622 IN+ 1 V CC GND 2 IN- 3 4 OUT SC7 Pin Description PIN NAME FUNCTION 1 IN+ Positive Input 2 GND Ground 3 IN- Negative Input 4 OUT Output V CC Positive Power Supply. Bypass with a.1µf capacitor to ground. www.maximintegrated.com Maxim Integrated 7
Detailed Description The MAX9622 is a power-efficient, high-speed op amp ideal for capturing fast edges in a wide variety of signal processing applications. It precisely calibrates its V OS on power-up to eliminate the effects of package stresses, power supplies, and temperature. Applications Information Power-Up Autotrim The MAX9622 features power-up autotrimming that allows the devices to achieve less than 1µV of input offset voltage. The startup sequence takes approximately 4ms to complete after the supply voltage exceeds an internal threshold of 1.8V. During this time, the inputs and outputs are connected to an auxiliary amplifier that has an input offset of mv (typ). As soon as the autotrimming is completed, the inputs and outputs switch from the auxiliary amplifier to the calibrated amplifier. The calibration settings hold until the supply voltage drops below an internal threshold of 1.4V. This could be used to recalibrate the amplifier. The supply current of the part increases to about 2.mA during the power-up autotrim period. Use good supply decoupling with low ESR capacitors. Active Filters The MAX9622 is ideal for a wide variety of active filter circuits that make use of their wide output voltage swings and large bandwidth capabilities. The Typical Application Circuit shows a multiple feedback active filter circuit example with a 1kHz corner frequency. At low frequencies, the amplifier behaves like a simple low-distortion inverting amplifier gain = -1, while its high bandwidth gives excellent stopband attenuation above its corner frequency. See the Typical Application Circuit. Input Differential Voltage Protection During normal op-amp operation, the inverting and noninverting inputs of the MAX9622 are at essentially the same voltage. However, either due to fast input voltage transients or due to loss of negative feedback, these pins can be forced to different voltages. Internal back-to-back diodes and series resistors protect input-stage transistors from large input differential voltages (see Figure 2). IN+ and IN- can survive any voltage between the powersupply rails. This op amp has been designed to exhibit no phase inversion to overdriven inputs. V CC V OUT V 1.8V V 2V V Figure 1. Autotrim Timing Diagram AUXILIARY AMPLIFIER ACTIVE 1Ω 1Ω 4ms CALIBRATED AMPLIFIER ACTIVE Figure 2. Input Protection Circuit www.maximintegrated.com Maxim Integrated 8
Package Information For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a +, #, or - in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. SC7 X+1 21-76 9-188 www.maximintegrated.com Maxim Integrated 9
Revision History REVISION NUMBER REVISION DATE DESCRIPTION PAGES CHANGED 9/1 Initial release 1 4/1 Removed automotive reference from data sheet 1 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated s website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. 21 Maxim Integrated Products, Inc. 1