NEWS 2009 Part. N 95.0423/0 MINITEC NEWS 2009 1
TABLE OF CONTENT INTRODUCTION CONTENTS 3 END CAP Z WITH HAMMER TAPS 3 END CAP 45X45 VA 4 ANGLE 25 GD-Z 4 ANGLE 45X90 GD-Z 5 ANGLE 90 GD-Z 5 HINGE 19 S 6 HINGE 32 S 6 HINGE 45 S 7 DOOR HINGE SMALL 7 DOOR HINGE LARGE 8 T-SLOT MAGNET 8 SEALING PROFILE 9 SLIDE LR6 COMPACT 9 SLIDE LR6 COMPACT 10 RAIL LR 6 COMPACT 10 UNIVERSAL CLAMPING SOCKET 11 SLIDE G 32 11 BRACKET CONSOLE FOR MINIATURE ADJUSTMENT UNIT 12 CENTER DRIVE - 3 WHEELS SYSTEM 12 CUP HOLDER 2 MINITEC NEWS 2009
END CAP Z WITH HAMMER TAPS Part. N 22.1007/1 - End cap 19x45 Z Part N 22.1001/1 - End cap 32x32 Z Part N 22.1002/1 - End cap 45x45 Z Part N 22.1004/1 - End cap 45x90 Z Part N 22.1007/1 - Good clamping effectiveness via hammer taps in the star-shaped hole - Simple disassembly - The end cap can be re-used with replacement pins - Hammer the taps flush using a plastic hammer - For dismantling, hammer the pin with a ø 4 centre punch - Replacement pins (10 pack) Part N 221009/1 END CAP 45X45 VA Part. N 21.0026/0 - End cap stainless steel - With fixing pan head screw M8 x 10 stainless steel - For Profile VA and Profile AL - ESD on request - Rounded edges - Tap an M8 thread 12 mm deep into the profile - Place the end cap on and turn until the screw safety catches - Screw in the screw included in the scope of delivery with SW4 MINITEC NEWS 2009 3
ANGLE 25 GD-Z Part. N 21.0969/0 - Aluminium GD, powder coated, grey - Fixing kit - Removable centering tabs - Weight 0,066 kg - General constructions, particularly useful for subsequent fitting of profiles into existing constructions - Fixing of panel elements, table tops - Strengthening of profile constructions - Use fixing kit from supply schedule - Break centering tabs with pliers if nonaligning grooves - For subsequent mounting into vertical profiles use square nut M8 with positionfixing Part N 21.1351/2 - End cap MW 25 GD-Z Part. N 22.0997/1 ANGLE 45X90 GD-Z Part. N 21.1397/0 TECHN. DATA / ITEMS SUPPLIED - Aluminium GD, powder coated, grey - Fixing kit - Weight 0,281 kg - General constructions, particularly useful for subsequent fitting of profiles into existing constructions - Fixing of panel elements, table tops - Strengthening of profile constructions - Use fixing kit from supply schedule - For mounting into vertical profile use square nut M8 with position-fixing Part N 21.1351/2 - Recommended locking torque 20 Nm - Use hammer-head screw Part N 21.1370/0 - Suitable end cap MW 45x90 GD-Z Part N 22.0998/1 4 MINITEC NEWS 2009
ANGLE 90 GD-Z Part. N 21.0978/0 TECHN. DATA / ITEMS SUPPLIED - Aluminium GD, powder coated, grey - Fixing kit - Weight 0,460 kg - For profiles 90 and 180 - General constructions, particularly useful for subsequent fitting of profiles into existing constructions - Fixing of panel elements, table tops - Strengthening of all profile connections - Use fixing kit from supply schedule - For subsequent mounting into vertical profiles use square nut M8 with positionfixing Part N 21.1351/2 - Hammer head screw can be used - Recommended locking torque 20 Nm - Suitable end cap MW 90 GD-Z Part N 220999/1 HINGE 19 S Part. N 21.1044/0 TECHN. DATA / ITEMS SUPPLIED - Aluminium GD, powder coated, grey - Without fixing kit - with end caps - Weight 0,100 kg - Load max. 600 N - Suitable for large doors and flaps of profile type 19 or 32 - Guard units - Connection of profiles 19 and 32 at any angle - Fasten hinge with 4 M6 x 18 bolts and 4 square nuts on the profile groove, or with screws corresponding to the material thickness directly on the panel elements - For heavy-duty applications use multiple hinges MINITEC NEWS 2009 5
HINGE 32 S Part. N 21.1055/0 TECHN. DATA / ITEMS SUPPLIED - Aluminium GD, powder-coated, grey - Without fixing kit - With end caps - Weight 0,105 kg - Load max. 600 N - Suitable for large doors and flaps - Guard units - Connection of profiles 19, 32 and 45 at any angles - Fasten hinge with 4 M6 x 18 bolts and 4 square nuts on the profile groove or with screws corresponding to the material thickness directly on the panel elements - Fasten hinge with M8 x 30 bolt on the 45 x 45 profile face side; fasten the other hinge half with M6 x 20 bots and square nuts on the profile groove or with M6 x 18 bolts corresponding to the material thicknes - For heavy-duty applications use multiple hinges HINGE 45 S Part. N 21.1098/0 TECHN. DATA / ITEMS SUPPLIED - Aluminium GD, powder-coated, grey - Without fixing kit - With End caps - Weight 0,110 kg - Load max. 600 N - Suitable for large doors and flaps - Guard units - Connection of profiles at various angles - For higher loads use more hinges - 1: 2 screws M8 x 30-2: 2 screws M6 x 18, square nuts M6, 1 screw M8 x 30-3: 2 screws M6 x 18, 2 square nuts M6, 2 screws M6 for panel element according to material - 4: 4 screws M6 x 18, 4square nuts M6 6 MINITEC NEWS 2009
DOOR HINGE SMALL Part. N 21.0973/0 - Aluminium - Fixing kit - Weight 0,120 kg - Suitable for large doors and lids - Guard units - Connection of profiles at any angle - Use fixing kit from supply schedule DOOR HINGE LARGE Part. N 21.0970/0 - Aluminium - Fixing kit - Weight 0,235 kg - Suitable for large doors and lids - Guard units - Connection of profilles at any angle - Use fixing kit from supply schedule MINITEC NEWS 2009 7
T-SLOT MAGNET Part. N 21.0023/0-1 Magnet NeFeB zinc-plated - Without fixing kit - Weight 0,13 kg - Attention: Electric- and memory devices can be faulted by the magnet - Adhesive magnet for tools - Below conveyors as guidance, for magnetisable trnasported material or for higher conveyiry speed - Insert magnet into t-slot - For fixing: (strongly recommended) Use end cap Al, set screw M8 x 12 with square nut M8 or t-slot bar SEALING PROFILE Part. N 22.1011/0 - Weight 0,122 kg/m - Length 100 m - Sealing of doors, lids and other constructions against water, dust and noise - Press into profile groove 8 MINITEC NEWS 2009
SLIDE LR6 COMPACT Part. N 28.0140/0 TECH. DATA / ITEMS SUPPLIED - Aluminium, all faces machined - 3 Double row, angular-contact bearings - Assembled ready for use - Weight 0,194 kg - MiniTec linear guide systems LR 6 - Material-handling - Measuring devices - Doors - Slip slide onto rail - Adjust clearance with key 2,5 A/F - Tighten fixing screw with a torque of 20 Nm SLIDE LR6 COMPACT Part. N 28.0127/0 - Slide PEUHMW, black - With square nut M8, steel zinc-plated - Weight 0,068 kg - Material-handling - Measuring devices - Doors - Slip slide onto rail - Adjust slide clearance with hexagon key MINITEC NEWS 2009 9
RAIL LR 6 COMPACT Part. N 28.0016/0 TECH. DATA / ITEMS SUPPLIED - Aluminium, natural anodized E6/EV 1-2 Shafts Cf 53 h6, steel - With fixing bores Ø 8,5 mm, grid: 150 mm - Weight 1,779 kg/m - Lenght 4 m - Material-handling - Measuring devices - Doors - Fasten rail with countersunk screws M8 x 20 and square nut M8 on MiniTec profile UNIVERSAL CLAMPING SOCKET Part. N P20.060/0 - Case PA 6 GF - Knurled screw steel - Weight 0,037 kg - For assembly of pneumatic switches for learning and training purposes - To fasten diverse pneumatic switches - Fastening of valves including those from different manufacturers - Simple pneumatic accessories fastened with M3 screws (not in scope of delivery) onto the clamping socket - By pressing the knurled screw, the clamping socket can be fit into the slot - When released, it is automatically indexed 10 MINITEC NEWS 2009
SLIDE G 32 Part. N 28.0355/0 TECHN. DATA / ITEMS SUPPLIED - Slide aluminium anodized - Slide bearing (plastic) - Without adjusting units - Weight 0,314 kg - to adjust light barriers, reflectors, side guides etc. - Insert the slides of the mini adjustment unit into the sliding guides and turn the spindle - Adjust using the play of the M6 tensioning screw - Fasten the spindle bearing to the handle profile 32 BRACKET CONSOLE FOR MINIATURE ADJUSTMENT UNIT Part. N 28.0371/0 - Console aluminium, natural anodized - Without fixing kit - Weight 0,044 kg - For connection of two adjustment units Part N 28.0351/0, 28.0352/0 and 28.0353/0 - For connecting small loads, such as light barriers, sensors etc. - Each with two M6 threads, 10 mm deep, separation of 25 mm placed into slides - Connect adjustment units with cylinder head screws M6x15 MINITEC NEWS 2009 11
CENTER DRIVE - 3 WHEELS SYSTEM Part. N 29.5260/0 - Cylinder, steel zink-plated - Ball bearings on both sides - With Fixing kit - Part. N 29.5260/0 Weight with drive ø 50: 50,800 kg/m - Space saving drive - Motor below conveyor - Suitable for nosebar on both ends - First install sheets - Assemble driving drum, tensioning drive and bearing housing - Assemble sprocked wheel, chain and motor. Adjust belt-tension after that - Part. N 29.5261/0 Weight with drive ø 70: 70,566 kg/m CUP HOLDER Part. N 32.0544/0 - Cup holder aluminium anodized - Cup with MiniTec company logo - With fixing kit - Weight 0,580 kg - Cup or bottle holder for workplace systems - With cut-out for cup handel - Screw on profile constructions by using fixing kit 12 MINITEC NEWS 2009