ThermoSpan EPS DETAIL LIST 00 / 15 COVER SHEET 01 / 15 RIDGE DETAIL 02 / 15 HEAD FLASHING DETAIL 03 / 15 EAVES GUTTER DETAIL 04 / 15 INSULATED GUTTER 05 / 15 INSULATED BOX GUTTER 06 / 15 BARGE CAPPING DETAIL 07 / 15 BARGE/PARAPET DETAIL 08 / 15 END LAP DETAIL 09 / 15 EXPANSION STEP DETAIL 10 / 15 SKYLIGHT PANEL DETAIL (OPTIONAL) 11 / 15 INSULATED PENETRATION DETAIL 12 / 15 SIDE LAP DETAIL 13 / 15 FASCIA AND BARGE FLASHING DIMENSIONS 14 / 15 SIDE BARGE FLASHING DIMENSIONS 15 / 15 PANEL PROFILE AND SIE CREPS www.metalcraftgroup.co.nz Architectural / Specification Enquiries Ph: 09 274 0408 Mobile: 027 603 1096 Email: Frances.charles@unitedindustries.co.nz
ACCEPTABLE SOLUTION AS PER E2/ASI SITUATION 1 SITUATION 2 SITUATION 3 1. LOW, MEDIUM, HIGH WIND ONES, WHERE ROOF PITCH 10 1. ALL ROOF PITCHES IN VERY HIGH WIND ONE 2. LOW, MEDIUM, HIGH WIND ONES WHERE ROOF PITCH 10 1. FOR ALL ROOF PITCHES IN EXTRA HIGH WIND ONES X MIN. 130mm (EXCLUDDING ANY SOFT EDGE OR TURN-DOWN TO ) MIN. 200mm (EXCLUDDING ANY SOFT EDGE OR TURN-DOWN TO ) PRE-FINISHED RIDGE CAP 0.55 FLASHING ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE CATEGORY A 1. NORMAL EXPOSURE 2. ROOF PITCH >10 CATEGORY B 1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kpa. 2. ROOF PITCH <10 X MIN. 130mm MIN. 200mm PROFILED EDGE OVER THERMOSPAN RIBS X X 5mm GAP 3 min. PRE-FINISHED SELF-TAPPING TEK SCREW WITH NEOPRENE WASHER TO EVERY RIB STOPENDS TO ROOF CLADDING 5mm POP RIVETS OR PREFINISHED SELF TAPPING SCREW WITH NEOPRENE WASHER PROFILLED FILLER SEALED TOP & BOTTOM BUTYL TAPE (OPTIONAL) 300mm MAXIMUM STRUCTURAL STEEL FRAMING BY ENGINEER METALCRAFT MSS PURLIN BY ENGINEER 0.55mm COLORSTEEL FLASHING FOAM INFILL RIDGE DETAIL 01 / 15
PROFILED FILLER SEALED TOP AND BOTTOM 5mm POP RIVET BEDDED IN SILICONE OR PRE-FINISHED 8g WAFER-TEK SCREW STOP ENDS TO PANEL X PROFILED EDGE OVER THERMOSPAN RIBS PRE-FINISHED SELF-TAPPING TEK SCREW WITH NEOPRENE WASHER TO EVERY RIB FOAM SEAL BUTYL TAPE 0.55 HEAD FLASHING ACCEPTABLE SOLUTION AS PER E2/ASI STRUCTURAL STEEL FRAMING BY ENGINEER METALCRAFT THERMOSPAN X SITUATION 1 1. LOW, MEDIUM, HIGH WIND ONES, WHERE ROOF PITCH 10 MIN. 130mm (EXCLUDING ANY SOFT EDGE OR TURN-DOWN TO ) MIN. 50mm SITUATION 2 1. VERY HIGH WIND ONE 2. LOW, MEDIUM AND HIGH WIND ONES WHERE ROOF PITCH 10 MIN. 200mm (EXCLUDING ANY SOFT EDGE OR TURN-DOWN TO ) MIN. 70mm SITUATION 3 1. ALL ROOF PITCHES IN EXTRA HIGH WIND ONE MIN. 200mm (EXCLUDING ANY SOFT EDGE OR TURN-DOWN TO ) MIN. 90mm ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE CATEGORY A CATEGORY B X 1. NORMAL EXPOSURE 2. ROOF PITCH >10 MIN. 130mm MIN. 50mm (VERTICALLY DOWN FACE - SMOOTH) MIN. 75mm (VERTICALLY DOWN FACE - PROFILED) 1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kpa. 2. ROOF PITCH <10 MIN. 200mm MIN. 75mm (VERTICALLY DOWN FACE - SMOOTH) MIN. 100mm (VERTICALLY DOWN FACE - PROFILED) HEAD FLASHING DETAIL 02 / 15
PRE-FINISHED SELF- TAPPING TEK SCREW WITH NEOPRENE WASHER TO EVERY RIB FOAM SEAL 75 3 min. METALCRAFT BOX GUTTER 175 WITH EXTERNAL BRACKET BUTYL TAPE (OPTIONAL) PRE-FINISHED 0.55 GUTTER FLASHING FASTEN GUTTER BRACKET WITH SUITABLE LENGTH TEK SCREWS INTO FASCIA PURLIN INSULATED PANEL STRUCTURAL STEEL FRAMING BY ENGINEER EAVES GUTTER DETAIL 03 / 15
5 min. PARAPET AND COVER FLASHINGS (BY OTHERS) 75 MIN 3 min. PRE-FINISHED SELF-TAPPING TEK SCREW WITH NEOPRENE WASHER TO EVERY RIB 75 100mm BUTYNOL CONTINTUED CONCRETE PARAPET (BY OTHERS) BUTYNOL 75 MINIMUM 150 MINIMUM 75 MIN 1.5mm STEEL BRACKET BUTYL TAPE (OPTIONAL) METALCRAFT MSS PURLIN BY ENGINEER INSULATED PANEL INSULATED PANEL GUTTER (SUPPORTED BY OTHERS) ROOF SUPPORT STRUCTURE INSULATED GUTTER 04 / 15
250mm MIN PRE-FINISHED SELF-TAPPING TEK SCREW WITH NEOPRENE WASHER IN EVERY RIB 80 80 BUTYNOL METALCRAFT MSS PURLIN BY ENGINEER 0.55 FILLET BRACKET 75 MIN 75 MIN 1.5mm STEEL BRACKET (BY OTHERS) BUTYL TAPE (OPTIONAL) INSULATED PANEL INSULATED PANEL INSULATED PANELS ROOF SUPPORT STRUCTURE INSULATED BOX GUTTER 05 / 15
Y PRE-FINISHED SELF-TAPPING TEK SCREW WITH NEOPRENE WASHER TO EVERY RIB 5mm GAP 0.55 PROFILE FLASHING (NOT REQUIRED WHEN OVER 2 RIBS) FOAM INFILL ROOF SUPPORT STRUCTURE METALCRAFT INSULATED PANEL ACCEPTABLE SOLUTION AS PER E2/ASI SITUATION 1 SITUATION 2 SITUATION 3 Y 1. LOW, MEDIUM, HIGH WIND ONES, WHERE ROOF PITCH 10 AT LEAST TWO CRESTS 1. VERY HIGH WIND ONE 2. LOW, MEDIUM & HIGH WIND ONES WHERE ROOF PITCH 10 AT LEAST TWO CRESTS 1.ALL ROOF PITCHES IN EXTRA HIGH WIND ONE AT LEAST TWO CRESTS MIN. 50mm MIN. 70mm MIN. 90mm ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE CATEGORY A CATEGORY B Y 1. NORMAL EXPOSURE 2. ROOF PITCH >10 ONE RIB (TRAPEOIDAL & TRAY) 2 CORRUGATIONS MIN. 50mm (VERTICALLY DOWN FACE - SMOOTH) MIN. 75mm (VERTICALLY DOWN FACE - PROFILED) 1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kpa. 2. ROOF PITCH <10 ONE RIB, TWO RIBS (<20mm) (TRAPEOIDAL & TRAY) 3 CORRUGATIONS MIN. 75mm (VERTICALLY DOWN FACE - SMOOTH) MIN. 100mm (VERTICALLY DOWN FACE - PROFILED) BARGE CAPPING DETAIL 06 / 15
ACCEPTABLE SOLUTION AS PER E2/ASI SITUATION 1 SITUATION 2 SITUATION 3 1. LOW, MEDIUM, HIGH WIND ONES, WHERE ROOF PITCH 10 1. ALL ROOF PITCHES IN VERY HIGH WIND ONE 2. LOW, MEDIUM, & HIGH WIND ONES WHERE ROOF PITCH 10 1. ALL ROOF PITCHES IN EXTRA HIGH WIND ONE G MIN. 35mm MIN. 35mm MIN. 35mm N MIN. 75mm MIN. 75mm MIN. 75mm PARAPET AND COVER FLASHINGS L MIN. 130mm (EXCLUDING ANY SOFT EDGE OR TURN-DOWN TO ) MIN. 50mm MIN. 200mm (EXCLUDING ANY SOFT EDGE OR TURN-DOWN TO ) MIN. 70mm MIN. 200mm (EXCLUDING ANY SOFT EDGE OR TURN-DOWN TO ) MIN. 90mm G N L PRE-FINISHED SELF-TAPPING TEK SCREW TO EVERY RIB WITH SEALED WASHER 0.55mm APRON FLASHING FLASHING TO SECOND CROWN OR USE '' FLASHING ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE G N L CATEGORY A 1. NORMAL EXPOSURE 2. ROOF PITCH >10 25mm MIN. 50mm + HEM OR 75mm (VERTICALLY UP FACE - SMOOTH) MIN. 75mm + HEM OR 100mm (VERTICALLY UP FACE - PROFILED) MIN. 150mm MIN. 50mm (VERTICALLY DOWN FACE - SMOOTH) MIN. 75mm (VERTICALLY DOWN FACE - PROFILED) CATEGORY B 1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kpa. 2. ROOF PITCH <10 25mm MIN. 75mm + HEM OR 100mm (VERTICALLY UP FACE - SMOOTH) MIN. 100mm + HEM OR 125mm (VERTICALLY UP FACE - PROFILED) MIN. 200mm MIN. 75mm (VERTICALLY DOWN FACE - SMOOTH) MIN. 100mm(VERTICALLY DOWN FACE - PROFILED) PANEL 6X4 BUTYL TAPE FOAM SEAL ROOF SUPPORT STRUCTURE CONCRETE PARAPET (BY OTHERS) BARGE/PARAPET DETAIL 07 / 15
3 min. 225 6x4mm BUTYL SEALANT OVERLAP METALCRAFT THERMOSPAN STITCHING SCREWS WITH NEO WASHER TWO PER PAN METALCRAFT THERMOSPAN EPS PRE-FINISHED SELF- TAPPING TEK SCREW WITH NEOPRENE WASHER TO EVERY RIB ROOF SUPPORT STRUCTURE END LAP DETAIL 08 / 15
5mm GAP DETAIL RECOMMENDED WHERE ROOF RUNS EXCEED 16m 0.55mm COLORSTEEL FLASHING PROFILED FILLER SEALED TOP AND BOTTOM TURN DOWN PAN APRROX 20 (SPECIAL TOOL AVAILABLE) TURN UP PAN TO FULL RIB HEIGHT (SPECIAL TOOL AVAILABLE) FOAM INFILL 50mm ROOF STEP 50mm ROOF STEP PANEL PRE-FILLED SELF-TAPPING TEK SCREW WITH NEOPRENE WASHER TO EVERY RIB (TYPICAL) ROOF SUPPORT STRUCTURE BUTYL TAPE 3 min. 4mm Ø STEEL RIVET EXPANSION STEP DETAIL 09 / 15
ALSYNITE RECOMMEND CONTINUOUS RUN FROM RIDGE TO GUTTER R-VALUE OF ROOFLIGHT =0.57 NO SAFETY MESH REQUIRED FOR MORE INFORMATION REFER www.alsynite.co.nz TOPGLASS GC ULTRASAFE 1.8mm 3660GSM TOP SKIN TEK SCREW TO EVERY RIB WITH SEALED WASHER 6x4mm BUTYL TAPE EPS EPS LASERLITE MAKROLON TWO LAYERS, 6mm LAMINATED TOGETHER ROOF SUPPORT STRUCTURE SKYLIGHT PANEL DETAIL (OPTIONAL) 10 / 15
50 700mm MAXIMUM PENETRATION PROVIDED & WEATHER SEALED BY OTHERS 1.6mm SOAKER TRAY 1.6mm SOAKER TRAY INSULATED PANEL UPSTAND SAME R-VALUE(min) AS ROOF TURN UP PANBS TO FULL RIB HEIGHT 250mm MIN 1.6mm ALUMINIUM DIVERTER WELDED TO SOAKER TRAY PRE-FINISHED SELF-TAPPING TEK SCREW WITH NEOPRENE WASHER IN EVERY RIB PROFILED FILLER SEALED TOP AND BOTTOM 300mm MAXIMUM BUTYL TAPE CUT BACK CROWN OF ROOF PROFILE 300mm MAXIMUM METALCRAFT THERMOSPAN BUTYL TAPE INSULATED PENETRATION DETAIL 11 / 15
TEK SCREW ROOF WASHER STITCHING 14G TEK SCREW, OPTIONAL 12mmØ EPDM SEAL BUTYL TAPE SEALANT METALCRAFT THERMOSPAN METALCRAFT THERMOSPAN ROOF SUPPORT STRUCTURE 6x4mm BUTYL TAPE SEALANT (WHERE OPTIMUM SEALING IS REQUIRED) Date 30.08.2016 Scale 1 : 2 SIDE LAP DETAIL 12 / 15
THERMOSPAN HEAD BARGE FLASHING 150 THERMOSPAN FACIA FLASHING 40 20 VARIES DEPENDENT ON PITCH TO SUIT ROOF PITCH (90 - ROOF PITCH) TO SUIT ROOF PITCH (90 + ROOF PITCH) 30 20 TO SUIT ROOF PITCH (90 - ROOF PITCH) TO SUIT ROOF PITCH (90 + ROOF PITCH) VARIES DEPENDENT ON PITCH 50 10 TURN UP WEATHER PROOF METALCRAFT THERMOSPAN EPS Ø5mm STEEL RIVETS @ 300mm CRS GUTTER HEAD BARGE FLASHING FASCIA FLASHING FASCIA AND BARGE FLASHING DIMENSIONS Date 30.08.2016 Scale 1 : 2 13 / 15
THERMOSPAN SIDE BARGE x = 2RIBS 38 Thermospan thickness SIDE BARGE Flashing Height (a) 50mm 115mm 110 75mm 100mm 140mm 165mm a 10 125mm 150mm 190mm 215mm 200mm 265mm 30 250mm 315mm Ø5mm RIVETS @ 300 CRS TURN UP WEATHER PROOF THERMOSPAN BARGE FLASHING THERMOSPAN BARGE FLASHING Date 30.08.2016 Scale 1 : 2 SIDE BARGE FLASHING DIMENSIONS 14 / 15
THERMOSPAN EPS A = 50, 75, 100, 125,150, 200, 250 250 1000 A 32 SCALE @ 1:5 FLAT FINISH INTERNAL LINER FINISHES SILKLINE FINISH 2 15 30 MESA FINISH 1 9 40 9 58 RIBBED FINISH 1 SCALE @ 1:2 12 4 107 Date 30.08.2016 PANEL PROFILE AND SIE ScaleAs indicated 15 / 15