Power Modules, Passivated Assembled Circuit Elements, 4 A FEATURES Glass passivated junctions for greater reliability Electrically isolated base plate PACE-PAK (D-9) PRIMARY CHARACTERISTICS I O 4 A Type Modules - thyristor, standard Package PACE-PAK (D-9) Available up to 2 V RRM /V DRM High dynamic characteristics Wide choice of circuit configurations Simplified mechanical design and assembly UL E78996 approved Material categorization: for definitions of compliance please see /doc?9992 DESCRIPTION The VS-P4 series of integrated power circuits consists of power thyristors and power diodes configured in a single package. With its isolating base plate, mechanical designs are greatly simplified giving advantages of cost reduction and reduced size. Applications include power supplies, control circuits and battery chargers. MAJOR RATINGS AND CHARACTERISTICS SYMBOL CHARACTERISTICS VALUES UNITS I O 8 C 4 A I TSM, 5 Hz 385 I FSM 6 Hz 4 A I 2 t 5 Hz 745 6 Hz 68 A 2 s I 2 t 745 A 2 s V RRM Range 4 to 2 V V ISOL 25 V T J T Stg -4 to +25 C ELECTRICAL SPECIFICATIONS VOLTAGE RATINGS TYPE NUMBER V RRM /V DRM, MAXIMUM REPETITIVE PEAK REVERSE AND PEAK OFF-STATE VOLTAGE V V RSM, MAXIMUM NON-REPETITIVE PEAK REVERSE VOLTAGE V VS-P4, VS-P42, VS-P43 4 5 VS-P42, VS-P422, VS-P432 6 7 VS-P43, VS-P423, VS-P433 8 9 VS-P44, VS-P424, VS-P434 VS-P45, VS-P425, VS-P435 2 3 I RRM MAXIMUM AT T J MAXIMUM ma Revision: 27-Jul-28 Document Number: 93755 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT /doc?9
ON-STATE CONDUCTION PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS Maximum DC output current 4 A I at case temperature O Full bridge circuits 8 C t = ms No voltage 385 Maximum peak, one-cycle I non-repetitive on-state or TSM, t = 8.3 ms reapplied 4 I forward current FSM t = ms % V RRM 325 A t = 8.3 ms reapplied Sinusoidal half wave, 34 t = ms No voltage initial T J = T J maximum 745 Maximum I 2 t for fusing I 2 t t = 8.3 ms reapplied 68 t = ms % V RRM 53 A 2 s t = 8.3 ms reapplied 48 Maximum I 2 t for fusing I 2 t t =. ms to ms, no voltage reapplied I 2 t for time tx = I 2 t tx 745 A 2 s Low level value of threshold voltage V T(TO) (6.7 % x x I T(AV) < I < x I T(AV) ), T J = T J maximum.83 High level value of threshold voltage V T(TO)2 (I > x I T(AV) ), T J = T J maximum.3 V Low level value of on-state slope resistance r t (6.7 % x x I T(AV) < I < x I T(AV) ), T J = T J maximum 9.6 High level value of on-state slope resistance r t2 (I > x I T(AV) ), T J = T J maximum 7. m Maximum on-state voltage drop V TM I TM = x I T(AV) T J = 25 C.4 V Maximum forward voltage drop V FM I FM = x I F(AV) T J = 25 C.4 V Maximum non-repetitive rate of rise of turned-on current di/dt T J = 25 C from.67 V DRM I TM = x I T(AV), I g = 5 ma, t r <.5 μs, t p > 6 μs Maximum holding current I H 3 T J = 25 C anode supply = 6 V, resistive load Maximum latching current I L 25 2 A/μs ma BLOCKING PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS Maximum critical rate of rise of off-state voltage dv/dt T J = 25 C, exponential to.67 V DRM gate open 2 V/μs Maximum peak reverse and off-state leakage current at V RRM, V DRM I RRM, I DRM T J = 25 C, gate open circuit ma Maximum peak reverse leakage current I RRM T J = 25 C μa 5 Hz, circuit to base, all terminals shorted, RMS isolation voltage V ISOL T J = 25 C, t = s 25 V TRIGGERING PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS Maximum peak gate power P GM 8 Maximum average gate power P G(AV) 2 W Maximum peak gate current I GM 2 A Maximum peak negative gate voltage -V GM V T J = 25 C 2 V T J = - 4 C 3 T J = 25 C Anode supply = T J = - 4 C 6 V resistive load 9 Maximum gate current required to trigger I GT T J = 25 C 6 ma T J = 25 C 35 Maximum gate voltage that will not trigger V GD.2 V T J = 25 C, rated V DRM applied Maximum gate current that will not trigger I GD 2 ma Revision: 27-Jul-28 2 Document Number: 93755 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT /doc?9
THERMAL AND MECHANICAL SPECIFICATIONS PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS Maximum junction operating and storage temperature range T J, T Stg -4 to +25 C Maximum thermal resistance, junction to case per junction R thjc DC operation.5 Maximum thermal resistance, case to heatsink R thcs Mounting surface, smooth and greased. K/W Mounting torque, base to heatsink () 4 Nm Approximate weight Case style 58 g 2. oz. PACE-PAK (D-9) Note () A mounting compound is recommended and the torque should be checked after a period of 3 hours to allow for the spread of the compound Maximum Total Power Loss (W) 2 93755_a 8 6 4 2 T J = 25 C ~ + - 8 (sine) 5 5 2 25 3 35 4 Total Output Current (A) Maximum Total Power Loss (W) 2 93755_b Fig. - Current Ratings Nomogram ( Module Per Heatsink) 8 6 4 2 K/W.5 K/W 2 K/W 3 K/W 5 K/W K/W R thsa =.7 K/W - ΔR 25 5 75 25 Maximum Allowable Ambient Temperature ( C) 3 4 Maximum Average On-State Power Loss (W) 93755_2 25 2 5 5 8 2 9 6 3 Ø Conduction angle T J = 25 C 5 5 2 Average On-State Current (A) RMS limit Maximum Average On-State Power Loss (W) 93755_3 35 3 25 2 5 5 DC 8 2 9 6 3 RMS limit Ø Conduction period T J = 25 C 5 5 2 25 3 35 Average On-State Current (A) Fig. 2 - On-State Power Loss Characteristics Fig. 3 - On-State Power Loss Characteristics Revision: 27-Jul-28 3 Document Number: 93755 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT /doc?9
Maximum Allowable Case Temperature ( C) 93755_4 3 2 9 8 7 Per module Fully turned-on 8 (Sine) 8 (Rect.) 5 5 2 25 3 35 4 45 Total Output Current (A) Fig. 4 - Current Ratings Characteristics Peak Half Sine Wave On-State Current (A) 93755_6 35 325 3 275 25 225 2 75 5 At any rated load condition and with rated V RRM applied following surge. Initial T J = 25 C at 6 Hz.83 s at 5 Hz. s Number of Equal Amplitude Half Cycle Current Pulses (N) Fig. 6 - Maximum Non-Repetitive Surge Current Instantaneous On-State Current (A) 93755_5 T J = 25 C T J = 25 C.5..5 2. 2.5 3. 3.5 4. 4.5 5. Instantaneous On-State Voltage (V) Fig. 5 - On-State Voltage Drop Characteristics Peak Half Sine Wave On-State Current (A) 93755_7 4 35 3 25 2 5. Maximum non-repetitive surge current versus pulse train duration. Control of conduction may not be maintained. Initial T J = 25 C No voltage reapplied Rated V RRM reapplied. Pulse Train Duration (s) Fig. 7 - Maximum Non-Repetitive Surge Current Z thjc - Transient Thermal Impedance (K/W). Steady state value R thjc =.5 K/W (DC operation)..... 93755_8 Square Wave Pulse Duration (s) Fig. 8 - Thermal Impedance Z thjc Characteristics Revision: 27-Jul-28 4 Document Number: 93755 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT /doc?9
Instantaneous Gate Voltage (V).. Rectangular gate pulse (a) Recommended load line for rated di/dt: V, 2 Ω, t r μs (b) Recommended load line for rated di/dt: V, 65 Ω, t r μs V GD I GD 93755_9 Instantaneous Gate Current (A) ORDERING INFORMATION TABLE (b) T J = 25 C T J = 25 C (a) T J = 4 C.. Fig. 9 - Gate Characteristics () P GM = W, t p = 5 ms (2) P GM = 2 W, t p = 25 ms (3) P GM = 5 W, t p = ms (4) P GM = W, t p = 5 μs () (2) (3) (4) Frequency limited by P G(AV) Device code VS- P 4 2 K W 2 3 4 5 6 7 - product 2 - Module type 3 - Current rating = 25 A DC (P series) 4 = 4 A DC (P4 series) 4 - Circuit configuration = single phase, hybrid bridge common cathode 2 = single phase, hybrid bridge doubler connection 3 = single phase, all SCR bridge 5 - Voltage code = 4 V 2 = 6 V 3 = 8 V 4 = V 5 = 2 V 6 - K = optional voltage suppression 7 - W = optional freewheeling diode Revision: 27-Jul-28 5 Document Number: 93755 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT /doc?9
CIRCUIT CONFIGURATION CIRCUIT DESCRIPTION CIRCUIT CONFIGURATION CODE SCHEMATIC DIAGRAM G TERMINAL POSITIONS Single phase, hybrid bridge common cathode AC AC2 G2 (-) (+) AC G - AC2 G2 + G G2 Single phase, hybrid bridge doubler connection 2 AC2 AC AC G - AC2 G2 + (-) (+) G3 G Single phase, all SCR bridge 3 AC AC2 G4 G2 (-) (+) AC2 G2 - G G4 AC G3 + CODING () CIRCUIT DESCRIPTION CIRCUIT CONFIGURATION CODE BASIC SERIES WITH VOLTAGE SUPPRESSION Note () To complete code refer to Voltage Ratings table, i.e.: for 6 V P4.W complete code is P42W WITH FREEWHEELING DIODE WITH BOTH VOLTAGE SUPPRESSION AND FREEWHEELING DIODE Single phase, hybrid bridge common cathode P4. P4.K P4.W P4.KW Single phase, hybrid bridge doubler connection 2 P42. P42.K - - Single phase, all SCR bridge 3 P43. P43.K - - Dimensions LINKS TO RELATED DOCUMENTS /doc?95335 Revision: 27-Jul-28 6 Document Number: 93755 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT /doc?9
Outline Dimensions D-9 PACE-PAK DIMENSIONS in millimeters (inches).9 x 45 (.35 x 45 ) 2.7 (.5) 2.7 (.5) Ø.65 (.6) 4.6 (.8) 2.5 (.) MAX. 63.5 (2.5) 5.5 (.6) MAX. 25 (.98) MAX. 45 (.77) Fast-on 6.35 x.8 (.25 x.3) 23.2 (.9) 5.2 (.2) 32.5 (.28) MAX. 33.8 (.33) 48.7 (.9) Document Number: 95335 For technical questions, contact: indmodules@vishay.com Revision: 24-Jul-8
Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. 27 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 8-Feb-7 Document Number: 9