1.Find these Parts First. 2.Take out F11, F12 For Fuselage Assembly. 3.Assemble F13 as below. Do not glue!!! 4.Assemble F4 as below. Do not glue!!! Do not glue!!! 5. Assemble F16 Do not glue!!! 6. Turn it over.
7. Find this part. It is marked- If it does not fit, pls check the mark to see whether it is 8. Assemble as below. Still Do not glue!!! 9. Find this part. It is marked- 10. Assemble it as below. After Assembly, it should look like this. Still Do not glue!!! 11. Check the lines below. Make sure they are straight. Make Sure They Are Straight Forward Still Do not glue!!! Still Do not glue!!! Make Sure They Are Straight Forward 12. Make sure all parts are in position, and glue. Make sure all parts are in proper position. Then glue them.
Glue each joint position. 13. Find Part F10. 14. Install F10 as below. 15. Glue F10. 15. Glue F10. 16. Find F14. 17. Install F14 as below. 18. Glue F14.
19. Find F15. 20. Install and glue F15 as below. 21. Find the fuselage parts as below photo shows. 22. Assemble as below. 23. Glue a little. Do not glue too much! 24. As photo shows, the characters face to interior. 5. Find the clear film. It's rapped with the white the paper. 26. Shear cut the clear windows.
27. Glue the Windows. Better to use foam glue here. 28. Find the below parts. 29. Install and drop glue to the small holes. This is Wrong!!! This is correct!
Glue as below red mark shows. The red line below should be straight! It should be symmetric! After check, glue it! Find F25 Install as below. Do not glue! Find F24. Install F24 as below. Do not glue!
Install F23 as below. Do not glue! Install F22 as below. Do not glue! Glue as below red mark shows. Find F20 and F21.
Install F21 as below. Install F20 as below. Install F17 as below. Find this wod bar. Fill this gap between F16 and f17 with the wood bar. Cut to keep the surface even and smooth.
Find F5. Install and glue F5. Find F6 and F7.5 Install and glue F6 and F7.5 as below. Install and glue F1 as below. Install and glue F2 as below.
Install and glue F3 as below. Find the 5x5mm wood bar. Install as below. Do not glue! Find F18 Install F18 as below. Do not glue! Glue after check the position is correct. Cut the wood bar after glue.
Install and glue F19 as below. Find the steel wires. Pull out the steel wire. Install the plastic tube first. This mark- means "Rudder" This mark- means "Elevator"
Push the steel wires through the tube. And glue as below yellow mark shows. Find some useless wood plate. Cut the wood plate small. Use the small wood to fill the gap as below and glue it.
Fill in this gap as well. Pull out the steel wire, and polish to keep the surface even. Push the steel wires through the tube again. Try to pull and push the steel wire to see whether it is smooth. Find below parts
Install as below. Fill the gap as well. Find F26.
Install f26 as below. Install the wood bar as below. Glue according to yellow mark below.
Cut to keep the surface even,
F2 and F3 should be perpendicular to fuselage side panel Find the front window. Install front window as below. Do not glue. Find F7.
Install F7 and DO NOT glue! Glue as below yellow mark. Be careful not to drop glue on window. Find F8, install and glue it. Install F9 over F8. Find a useless wood part.
Cut down a part as below, and glue it as yellow mark shows. Add wood part to both sides for stronger wing support. Polish the fuselage. At least 10 minutes. Before Polishing. After Polishing.
Before Polishing. After Polishing. Now start to Mask. Mask as below. Glue after install correctly.
Mask the bottom. Fill the gap.
Glue the back window. Now start Tail WIng installation
Install Hinges. Assemble and install motor strut.
Install X7 exactly as below. Do not glue! Wrong.
Right! Install and Glue. Polish Mask
Make sure the screw hole on the cowl match with the hole on X7. Then glue, and install Cowl. Pls polish the Surface before cover.
Put 11.1v 1500mAh Lipo battery at front. Fill the gap.