575W HMI Scan light ZIPPER 575 USER S MANUAL This manual must be considered an integral part of the projector. The user must read this manual before using the projector
AUTHORISED AND QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR. BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR. DO NOT OPEN THE PROJECTOR IF IT IS CONNECTED TO THE MAIN SUPPLY. FOR ANY DOUBT, CONTACT YOUR SUPPLIER OR SEND AN E-MAIL TO: tech@lamposrl.it
Dimensions & weight Weight: 20.5Kg Technical data - HMI 575 lamp - Magnetic ballast with power factor correction (3.7A max @ 230VAC with lamp ON) - DMX controlled or stand alone mode - PAN 200 8/16 bit, TILT 80 8/16 bit - 6 ROTATING GOBOS + W, interchangeable, with index adjustment, can rotate clockwise and counter-clockwise. - 9 FIXED GOBOS + W - 9 COLOURS + W - Motorized FOCUS - Linear DIMMER 0 100% - STROBE run s up to 10 flashes per second - PRISM x3 with adjustable rotation clockwise and counter-clockwise - Optics 14 120cm 2mt 4mt 6mt 8mt 80cm 40cm 0cm 40cm 80cm 120cm Lux 49.600 12.200 5.300 3.070 (optics 14 ) Diam. (cm) 48 95 143 190
DMX512 specifications CH. DMX FUNCTION 01 Dimmer The projector reads normally 14 consecutive 02 Shutter/Strobe DMX channels starting from the set address. 03 Focus 04 Colour 05 Pan (HSB) 06 Tilt (HSB) The REMOTE CONTROL is active depending 07 Gobo 1 selection Of the status of REMOTE option (INDEX 9) 08 Gobo 1 index position 09 Gobo 1 rotating speed 10 Prism (insertion/speed) 11 Remote control 12 Pan (LSB) only if HIGHRES=1 13 Tilt (LSB) only if HIGHRES=1 14 Gobo FIXED selection 01 DIMMER Controls the intensity of the light beam from 0 to 255. It also works during the Strobe function. The value of this channel is ignored if the shutter channel is in the CLOSE position. Open 252..255 Proportional 4..251 Intensity Min... Max Close 0..3 02 SHUTTER/STROBE Selects blackout, channel open and strobe functions. With the SHUT ON COLOUR function selected, the shutter closes during the colour change. With the SHUT ON GOBO function selected, the shutter closes during the gobo change. Open 248..255 Close 240..247 Blackout (It has priority over the dimmer) Strobe 29 232..239 Maximum rate Strobe 28 224..231 Strobe 27 216..223 Strobe 26 208..215 Strobe 25 200..207 Strobe 24 192..199 Strobe 23 184..191 Strobe 22 176..183 Strobe 21 168..175 Strobe 20 160..167 Strobe 19 152..159 Strobe 18 144..151 Strobe 17 136..143 Strobe 16 128..135 Strobe 15 120..127 Strobe 14 112..119 Strobe 13 104..111 Strobe 12 96..103 Strobe 11 88..95 Strobe 10 80..87 Strobe 9 72..79 Strobe 8 64..71 Strobe 7 56..63 Strobe 6 48..55 Strobe 5 40..47 Strobe 4 32..39 Strobe 3 24..31 Strobe 2 16..23 Strobe 1 8..15 Minimum rate Close 0..7 Blackout (It has priority over the dimmer)
03 FOCUS Controls the focus adjustment. With the DEFOCUS ON CHANGE option selected, the generated image goes out of focus during an effect change. Max 252..255 (far) Proportional 4..251 Min 0..3 (near) 04 COLOURS The channel selects the pre-set fixed positions (white + 9 full colours). If the SHUT ON COLOUR option is activated, the shutter is closed during the colour change. C9 252..255 C8 224..251 C7 196..223 C6 168..195 C5 140..167 C4 112..139 C3 84..111 C2 56..83 C1 28..55 WH 0..27 05/06 - PAN & TILT (8 bit) The Pan/Tilt movement is controlled by the received values on the Pan and Tilt channels. If the HIGHRES option is activated, the Pan and Tilt Fine extra channels set the real position of the Pan and Tilt movement in a fine way (5/6 + 12/13). If the REVERSE PAN and/or REVERSE TILT options are activated the Pan and/or Tilt movement directions are inverted. If the PANTILT SWAP option is activated, the Pan and Tilt functions swap between themselves. 07 GOBO 1 SELECTION It selects the rotating gobo preferred or no gobo at all. The angle desired or the speed and the way of rotation are indicated from other channels (Angle, Speed Rotating Gobo). If the SHUT ON GOBO option is activated the shutter is closed during the gobo change. If the DEFOCUS ON CHANGE option is activated, the projected image goes out of focus during the gobo change. Gobo 7 216..255 Gobo 6 180..215 Gobo 5 144..179 Gobo 4 108..143 Gobo 3 72..107 Gobo 2 36..71 Gobo 1 0..35 08 GOBO 1 INDEX Assigns to the gobo a position in the range of 360. The SHUT ON GOBO or the DEFOCUS ON CHANGE options has no effect in case of variation on this channel.
09 GOBO 1 ROTATION SPEED It selects the speed and the rotation way of the selected gobo from the Gobo Selection channel. The SHUT ON GOBO or the DEFOCUS ON CHANGE options has no effect in case of variation on this channel. If the REMOTE ENABLE option is not activated the AUX channel increases resolution of this channel. Stop 252..255 The GOBO holds the position assigned with the Gobo Index channel Clockwise Rotation 130..251 From maximum (130) to minimum (251) speed 126..129 Not valid values, no effects Counter-clockwise 4..125 From minimum (4) to maximum (125) speed Rotation Stop 0..3 The GOBO holds the position assigned with the Gobo Index channel 10 PRISM INSERT/ROTATION It selects the insertion and the speed of the prism rotation. The SHUT ON GOBO and the DEFOCUS ON CHANGE options have no effects in case of variation on this channel. Prism Out 252..255 Prism In 248..251 Insert still Clockwise Rotation 130..247 From maximum (130) to minimum (247) speed 126..129 Not valid values, no effect Counter-clockwise 8..125 From maximum (8) to minimum (125) speed Rotation. Prism In 4..7 Insert still Prism Out 0..3 11 AUX / REMOTE If the REMOTE ENABLE option is not activated, the channel performs the fine control of the speed of the rotating gobo. If the REMOTE ENABLE option is activated, the channel sends, via DMX, special codes to the projector, as LAMP ON/OFF, RESET and SET-UP. 12/13 - PAN & TILT (16 bit) If the HIGHRES option is activated, the Pan and Tilt Fine extra channels set the real position of the Pan and Tilt movement in a fine way (5/6 + 12/13). 14 GOBO FIXED SELECTION It selects the gobo preferred (9 gobos+ no gobo) or no gobo at all. If the SHUT ON GOBO option is activated the shutter is closed during the gobo change. If the DEFOCUS ON CHANGE option is activated, the projected image goes out of focus during the gobo change. GOBO 9 252..255 GOBO 8 224..251 GOBO 7 196..223 GOBO 6 168..195 GOBO 5 140..167 GOBO 4 112..139 GOBO 3 84..111 GOBO 2 56..83 GOBO 1 28..55 OPEN 0..27
User s interface Press and release the push-button MODE to access the different functions, as indicated by the three LED Index (green led on): see the table in the next page for the meaning. Use the + or - button to select the number of the Index. Parameter (yellow led on): Use the + or - button to select the value of the Parameter which must be checked or modified. To enable a modification, press the ENTER button; the display will flash twice as confirmation. Fault (red led flashing): it is possible to access this mode only if a fault has happened. When the cause of the fault will be removed, the indication will be automatically removed too. It is also possible to remove some fault indication, pressing the ENTER button. Pressing the - button it is possible to see how many faults are enabled (in this case the red LED stops flashing), pressing the + button, the system returns to the visualization of the current fault code. Automatic return to the default visualization: if no buttons are pressed for more than 30 seconds, the system automatically returns back to the default visualization: the DMX INDEX, if there aren't faults, or the current fault code. Permanent visualization of a fault, when existing: when a fault has happened, even if the Index or the Parameter mode have been enabled, the red "LED" stay on. Start-up codes: when the projector is switched on, the display visualised in a sequence, 2 codes that identify the software of the main electronic board: first the Device Code (example: Zipper #003) and second the Software Release (example: 1.05). Procedures of zero: when a start procedure is going on, the display will show only one 0 on the middle digit. Special function system: when the projector runs special functions, the 3-digit display flashes the same number. 000 - Calibration of start positions 111 - Calibration of the gobo 2 position 222 - Remote control of the parameters
Parameters The parameters Boolean type (min=0, max=1) enable the controlled function when their value is 1 and they unable it when their value is 0. The Index n 12 and n 16 depend on the hardware configuration. Index Description Parameter NAME EFFECT Min Default Max 0 DMX INDEX Sets the DMX address of the projector 1 1 500 1 PANTILT SWAP Exchanges the assignment of the DMX channels between PAN & TILT 2 REVERSE PAN Reverses the PAN movement 3 REVERSE TILT Reverses the TILT movement 4 SHUT ON COLOUR Closes the shutter before to change the colour, then re-open it 5 SHUT ON GOBO Closes the shutter before to change the gobo, then re-open it 6 DEFOCUS ON CHANGE The image goes out of focus before to change the colour or the gobo, or before the prism is enabled or disabled, then returns on focus 7 HIGHRES Enables the high resolution mode (16bit) for the PAN & TILT channels 8 PANTILT SOFT Progressive softening of the Pan & Tilt short movement when the parameter decreases 9 REMOTE ENABLE Enables the possibility to remote control the parameter of the projector via DMX 10 SYNCRO STROBE Selects the strobe mode Continuous strobe = 0: does not guarantee the synchronism of 2 or more projectors driven with the same DMX value; it can be used while programming Strobe sync. = 1 12 RESET COLOR Enables the manual reset of the colour wheel (the parameter is automatically reset at the end of the procedure) 13 RESET GOBO Enables the manual reset of the gobo wheel (the parameter is automatically reset at the end of the procedure) 14 RESET Enables the manual reset of the system (the parameter is automatically reset at the end of the procedure) 16 PROGRAM Enables the STAND ALONE function and sets the number EXECUTION of STEPS to execute into the loop 17 PROGRAM STEP Determines the current STEP of the inside program to which STEP SLOPE and STEP HOLD referred to 18 STEP SLOPE Determines the time, in seconds, of the slope before the current STEP 19 STEP HOLD Determines the time, in seconds, of the current STEP duration 20 LAMP LIFE Shows the life time, in hours, of the lamp Press the ENTER button to clear the counter 1 10 100 0 0 20 1 1 20 0 0 240 0 1 240 0-16.383
Remote Control If the REMOTE ENABLE parameter (Index n 10) is equal to 1, it is possible to modify or activate some functions of the projector, via DMX. The activation of controls is based on a precise time sequence of the DMX channels values, if a step of the sequence is wrong the sequence will be deleted and it will be necessary start from the beginning the sequence. The parameters All the STEPS of the following table must be executed. STEP DMX channels status Timing Action 1 CH1..CH11 = 0 4sec<time ------------------------------ 2 CH1..CH10 = 0 CH11 = 255 3 CH1..CH10 = 0 CH11 = 0 4 CH1..CH10 = 0 CH11 = 255 5 CH1..CH10 = any CH11 different from 0 and from 255 2sec<time The display flashes the number 222 to show the entrance in the parameters remote control. If the value of the DMX channel is minor than 9, the parameter will remain the same, if it is inclusive between 9 to 128, the parameter will be equal to 0, and if it is greater than 128, the parameter will be equal to 1. The PANTILT SOFT parameter is an exception as follow: If the value of the DMX channel is minor than 100, the parameter will remain the same, if it is inclusive between 100 to 200, the parameter will be equal to DMX value 100, and if it is greater than 200, the parameter will be equal to 100. 6 CH1..CH10 = any CH11 = 0 The coupling of the parameters and the DMX channels is as follow: PANTILT SWAP CH1 REVERSE PAN CH2 REVERSE TILT CH3 SHUT ON COLOUR CH4 SHUT ON GOBO CH5 DEFOCUS ON CHANGE CH6 HIGHRES CH7 PANTILT SOFT CH8 RESET CH10 ------------ The display will return to the usual visualized condition, to signal the exit from the remote control. The values of the DMX channels at the moment of the exit from the remote control condition will modify in a permanent way the parameters to which those are coupled. N.B. if the parameter RESET has been set at 1 will be executed a global reset procedure of the projector. These procedures can be enabled only if a fault happened during the search of the zero for the colour wheel, the gobo wheel and the gobo 1 position (fault code 22,23,24); in this case the parameter REMOTE CONTROL is forced to 1 and the device with the fault, will work on temporary mode. The DMX channel will work as a linear positioning, proportional to the value. When the remote insertion of the zero will be done, the channel will go back to normal mode.
Remote insertion of the zero positions All the STEPS of the following table must be executed. Insertion of the colour wheel zero STEP DMX channel status Timing Action 1 44<CH1<84 (25%) 108<CH11<148 (50%) 2 44<CH1<84 (25%) CH11=255 (100%) 3 44<CH1<84 (25%) CH11=0 (0%) --------------- The position of the colour wheel is recorded as zero position and the channel goes back to normal mode. All the STEPS of the following table must be executed. Insertion of the gobo 1 wheel zero STEP DMX channel status Timing Action 1 108<CH1<148 (50%) 108<CH11<148 (50%) 2 108<CH1<148 (50%) CH11=255 (100%) 3 108<CH1<148 (50%) CH11=0 (0%) --------------- The position of the gobo 1 wheel is recorded as zero position and the channel goes back to normal mode. All the STEPS of the following table must be executed. Insertion of the gobo index zero STEP DMX channel status Timing Action 1 172<CH1<212 (75%) 108<CH11<148 (50%) 2 172<CH1<212 (75%) CH11=255 (100%) 3 172<CH1<212 (75%) CH11=0 (0%) --------------- The initial index of the gobos is recorded as zero position and the channel goes back to normal mode. All the STEPS of the following table must be executed. Insertion of the gobo 2 wheel zero STEP DMX channel status Timing Action 1 240<CH1 (100%) 108<CH11<148 (50%) 2 240<CH1 (100%) CH11=255 (100%) 3 240<CH1 (100%) CH11=0 (0%) --------------- The position of the gobo 2 wheel is recorded as zero position and the channel goes back to normal mode.
Calibration procedures WARNING! USE THE CALIBRATION PROCEDURES CAREFULLY AND ONLY WHEN NECESSARY. Calibration of the reset positions (Gobos 1 and colours) Press the MODE and ENTER button together, for at least 5 seconds, until when the display will show 000 flashing. The DMX channel from 1 to 3 will give the value of the offset to add, or subtract, to the zero position DMX FUNCTION VALUE 1 Offset COLOUR wheel DMX channel = 0 offset = minus 4 steps 2 Offset GOBO 1 wheel DMX channel = 128 offset = 0 3 Offset GOBO position DMX channel = 255 offset = plus 4 steps To exit the calibration mode press ENTER: the set values will be stored. Calibration of the reset positions (fixed gobos wheel) Press the MODE and + button together, for at least 5 seconds, until when the display will show 111 flashing. The DMX channel 1will give the value of the offset to add, or subtract, to the zero position DMX FUNCTION VALUE 1 Offset GOBO 2 wheel DMX channel = 0 offset = minus 4 steps DMX channel = 128 offset = 0 DMX channel = 255 offset = plus 4 steps To exit the calibration mode press ENTER: the set values will be stored. Faults If the microprocessor finds a functional fault, it stores and shows that on the display. Can be stored up to a maximum of 5 codes of fault. Some faults can reset automatically as soon as disappear the cause that generated them, and some others have to be manually reset, pressing the ENTER button in the fault mode. CODE CAUSE EFFECT RESET 5 Absence of DMX signal The system wait for the signal Automatic 22 The zero COLOUR wheel sensor fault The COLOUR wheel will work on temporary mode (linear positioning of the wheel referred to the corresponding DMX channel) until when will Manual 23 The zero GOBO 1 wheel sensor fault 24 The zero GOBO 1 position sensor fault 25 The zero GOBO 2 wheel sensor fault be inserted, via remote control, the zero position. The GOBO 1 wheel will work on temporary mode (linear positioning of the wheel referred to the corresponding DMX channel) until when will be inserted, via remote control, the zero position. The GOBO 1 wheel will work on temporary mode (linear positioning of the wheel referred to the corresponding DMX channel) until when will be inserted, via remote control, the zero position. The GOBO 2 wheel will work on temporary mode (linear positioning of the wheel referred to the corresponding DMX channel) until when will be inserted, via remote control, the zero position. Manual Manual Manual
Inside program It is possible to create an inside program that allows the projector to function on "stand-alone" mode, so, it is not necessary to have a DMX controller to drive the projector. When the "stand-alone" function is enabled, the projector becomes a DMX generator which supply, via DMX line, the values corresponding to the inside program. WARNING!! To avoid conflicts of the DMX signal, if one projector is in this mode, it is necessary remove the connection with the DMX controller. The inside program runs a loop of up to 20 steps (PROGRAM STEP); each step contains: a DMX value of all the channels of the projector, a time slope to achieve the new step (STEP SLOPE) and a hold time of the step (STEP HOLD). Storing of the steps Via the DMX controller, give to the projector the position and the image required Set the value of STEP SLOPE (Index 18) to assign the time (in seconds) of the transition from the previous step to this new one Confirm with the ENTER button Set the value of STEP HOLD (Index 19) to assign the time (in seconds) of the hold time of this new step Confirm with the ENTER button Assign to the PROGRAM STEP parameter (Index 17) the number of the step you want memorize Push the ENTER button to store Execution of the inside program If the PROGRAM EXECUTION parameter (Index 16) contains "0", than the projector follows the command received from an external DMX controller, otherwise, if it contains a value between "1" and "20", than the projector execute a loop of steps from "1" to the number stored in the PROGRAM EXECUTION parameter. 1 2 3 N Modification of the program during execution If, during the execution of a program in "stand-alone" mode, you set a PROGRAM STEP value (Index 17) and then you push the ENTER button, the program in execution will jump directly to the step required. If, during the execution of a program in "stand-alone" mode, you set a STEP SLOPE value (Index 18) or a STEP HOLD value (Index 19) and then you push the ENTER button, the corresponding parameter of the step in execution will be modified. DMX Step 2 Step 1 Slope 1 Hold 1 Slope 2 Hold 2 Time
Lamp Replacement 1) Disconnect the projector from the main power supply 2) Unscrew the screws that hold the lamp cover 3) Remove the lamp cover 4) Remove the lamp, taking care to wear proper protective gloves 5) Insert a new lamp 6) Re-insert the lamp cover 7) Fix well all the screws that hold the lamp cover WARNING!! DISCHARGE LAMPS CONTAIN SUBSTANCES THAT CAN POLLUTE THE AMBIENCE. DISPOSE OF USING THE APPROPRIATE REFUGES (TOXIC). The improper use of this projector, cancel the guarantee and our responsibility. All the information have been written and driven with extreme care; however, we do not engage us any responsibility for contingent errors or omissions. We reserve the right to modify and/ or improve our product as we retain necessary, without subsequent warning or notice. It is forbidden any complete or partial reproduction of this handbook, if not expressly authorized.